diff options
Diffstat (limited to 'meta/recipes-connectivity/wpa-supplicant')
9 files changed, 483 insertions, 796 deletions
diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-AP-Silently-ignore-management-frame-from-unexpected-.patch b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-AP-Silently-ignore-management-frame-from-unexpected-.patch deleted file mode 100644 index 7b0713cf6d..0000000000 --- a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-AP-Silently-ignore-management-frame-from-unexpected-.patch +++ /dev/null @@ -1,82 +0,0 @@ -hostapd before 2.10 and wpa_supplicant before 2.10 allow an incorrect indication -of disconnection in certain situations because source address validation is -mishandled. This is a denial of service that should have been prevented by PMF -(aka management frame protection). The attacker must send a crafted 802.11 frame -from a location that is within the 802.11 communications range. - -CVE: CVE-2019-16275 -Upstream-Status: Backport -Signed-off-by: Ross Burton <ross.burton@intel.com> - -From 8c07fa9eda13e835f3f968b2e1c9a8be3a851ff9 Mon Sep 17 00:00:00 2001 -From: Jouni Malinen <j@w1.fi> -Date: Thu, 29 Aug 2019 11:52:04 +0300 -Subject: [PATCH] AP: Silently ignore management frame from unexpected source - address - -Do not process any received Management frames with unexpected/invalid SA -so that we do not add any state for unexpected STA addresses or end up -sending out frames to unexpected destination. This prevents unexpected -sequences where an unprotected frame might end up causing the AP to send -out a response to another device and that other device processing the -unexpected response. - -In particular, this prevents some potential denial of service cases -where the unexpected response frame from the AP might result in a -connected station dropping its association. - -Signed-off-by: Jouni Malinen <j@w1.fi> ---- - src/ap/drv_callbacks.c | 13 +++++++++++++ - src/ap/ieee802_11.c | 12 ++++++++++++ - 2 files changed, 25 insertions(+) - -diff --git a/src/ap/drv_callbacks.c b/src/ap/drv_callbacks.c -index 31587685fe3b..34ca379edc3d 100644 ---- a/src/ap/drv_callbacks.c -+++ b/src/ap/drv_callbacks.c -@@ -131,6 +131,19 @@ int hostapd_notif_assoc(struct hostapd_data *hapd, const u8 *addr, - "hostapd_notif_assoc: Skip event with no address"); - return -1; - } -+ -+ if (is_multicast_ether_addr(addr) || -+ is_zero_ether_addr(addr) || -+ os_memcmp(addr, hapd->own_addr, ETH_ALEN) == 0) { -+ /* Do not process any frames with unexpected/invalid SA so that -+ * we do not add any state for unexpected STA addresses or end -+ * up sending out frames to unexpected destination. */ -+ wpa_printf(MSG_DEBUG, "%s: Invalid SA=" MACSTR -+ " in received indication - ignore this indication silently", -+ __func__, MAC2STR(addr)); -+ return 0; -+ } -+ - random_add_randomness(addr, ETH_ALEN); - - hostapd_logger(hapd, addr, HOSTAPD_MODULE_IEEE80211, -diff --git a/src/ap/ieee802_11.c b/src/ap/ieee802_11.c -index c85a28db44b7..e7065372e158 100644 ---- a/src/ap/ieee802_11.c -+++ b/src/ap/ieee802_11.c -@@ -4626,6 +4626,18 @@ int ieee802_11_mgmt(struct hostapd_data *hapd, const u8 *buf, size_t len, - fc = le_to_host16(mgmt->frame_control); - stype = WLAN_FC_GET_STYPE(fc); - -+ if (is_multicast_ether_addr(mgmt->sa) || -+ is_zero_ether_addr(mgmt->sa) || -+ os_memcmp(mgmt->sa, hapd->own_addr, ETH_ALEN) == 0) { -+ /* Do not process any frames with unexpected/invalid SA so that -+ * we do not add any state for unexpected STA addresses or end -+ * up sending out frames to unexpected destination. */ -+ wpa_printf(MSG_DEBUG, "MGMT: Invalid SA=" MACSTR -+ " in received frame - ignore this frame silently", -+ MAC2STR(mgmt->sa)); -+ return 0; -+ } -+ - if (stype == WLAN_FC_STYPE_BEACON) { - handle_beacon(hapd, mgmt, len, fi); - return 1; --- -2.20.1 diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-Install-wpa_passphrase-when-not-disabled.patch b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-Install-wpa_passphrase-when-not-disabled.patch new file mode 100644 index 0000000000..c04c608bde --- /dev/null +++ b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-Install-wpa_passphrase-when-not-disabled.patch @@ -0,0 +1,33 @@ +From 57b12a1e43605f71239a21488cb9b541f0751dda Mon Sep 17 00:00:00 2001 +From: Alex Kiernan <alexk@zuma.ai> +Date: Thu, 21 Apr 2022 10:15:29 +0100 +Subject: [PATCH] Install wpa_passphrase when not disabled + +As part of fixing CONFIG_NO_WPA_PASSPHRASE, whilst wpa_passphrase gets +built, its not installed during `make install`. + +Fixes: cb41c214b78d ("build: Re-enable options for libwpa_client.so and wpa_passphrase") +Signed-off-by: Alex Kiernan <alexk@zuma.ai> +Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> +Upstream-Status: Submitted [http://lists.infradead.org/pipermail/hostap/2022-April/040448.html] +--- + wpa_supplicant/Makefile | 3 +++ + 1 file changed, 3 insertions(+) + +diff --git a/wpa_supplicant/Makefile b/wpa_supplicant/Makefile +index 0bab313f2355..12787c0c7d0f 100644 +--- a/wpa_supplicant/Makefile ++++ b/wpa_supplicant/Makefile +@@ -73,6 +73,9 @@ $(DESTDIR)$(BINDIR)/%: % + + install: $(addprefix $(DESTDIR)$(BINDIR)/,$(BINALL)) + $(MAKE) -C ../src install ++ifndef CONFIG_NO_WPA_PASSPHRASE ++ install -D wpa_passphrase $(DESTDIR)/$(BINDIR)/wpa_passphrase ++endif + ifdef CONFIG_BUILD_WPA_CLIENT_SO + install -m 0644 -D libwpa_client.so $(DESTDIR)/$(LIBDIR)/libwpa_client.so + install -m 0644 -D ../src/common/wpa_ctrl.h $(DESTDIR)/$(INCDIR)/wpa_ctrl.h +-- +2.35.1 + diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-PEAP-client-Update-Phase-2-authentication-requiremen.patch b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-PEAP-client-Update-Phase-2-authentication-requiremen.patch new file mode 100644 index 0000000000..620560d3c7 --- /dev/null +++ b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-PEAP-client-Update-Phase-2-authentication-requiremen.patch @@ -0,0 +1,213 @@ +From f6f7cead3661ceeef54b21f7e799c0afc98537ec Mon Sep 17 00:00:00 2001 +From: Jouni Malinen <j@w1.fi> +Date: Sat, 8 Jul 2023 19:55:32 +0300 +Subject: [PATCH] PEAP client: Update Phase 2 authentication requirements + +The previous PEAP client behavior allowed the server to skip Phase 2 +authentication with the expectation that the server was authenticated +during Phase 1 through TLS server certificate validation. Various PEAP +specifications are not exactly clear on what the behavior on this front +is supposed to be and as such, this ended up being more flexible than +the TTLS/FAST/TEAP cases. However, this is not really ideal when +unfortunately common misconfiguration of PEAP is used in deployed +devices where the server trust root (ca_cert) is not configured or the +user has an easy option for allowing this validation step to be skipped. + +Change the default PEAP client behavior to be to require Phase 2 +authentication to be successfully completed for cases where TLS session +resumption is not used and the client certificate has not been +configured. Those two exceptions are the main cases where a deployed +authentication server might skip Phase 2 and as such, where a more +strict default behavior could result in undesired interoperability +issues. Requiring Phase 2 authentication will end up disabling TLS +session resumption automatically to avoid interoperability issues. + +Allow Phase 2 authentication behavior to be configured with a new phase1 +configuration parameter option: +'phase2_auth' option can be used to control Phase 2 (i.e., within TLS +tunnel) behavior for PEAP: + * 0 = do not require Phase 2 authentication + * 1 = require Phase 2 authentication when client certificate + (private_key/client_cert) is no used and TLS session resumption was + not used (default) + * 2 = require Phase 2 authentication in all cases + +Signed-off-by: Jouni Malinen <j@w1.fi> + +CVE: CVE-2023-52160 +Upstream-Status: Backport [https://w1.fi/cgit/hostap/commit/?id=8e6485a1bcb0baffdea9e55255a81270b768439c] + +Signed-off-by: Claus Stovgaard <claus.stovgaard@gmail.com> + +--- + src/eap_peer/eap_config.h | 8 ++++++ + src/eap_peer/eap_peap.c | 40 +++++++++++++++++++++++++++--- + src/eap_peer/eap_tls_common.c | 6 +++++ + src/eap_peer/eap_tls_common.h | 5 ++++ + wpa_supplicant/wpa_supplicant.conf | 7 ++++++ + 5 files changed, 63 insertions(+), 3 deletions(-) + +diff --git a/src/eap_peer/eap_config.h b/src/eap_peer/eap_config.h +index 3238f74..047eec2 100644 +--- a/src/eap_peer/eap_config.h ++++ b/src/eap_peer/eap_config.h +@@ -469,6 +469,14 @@ struct eap_peer_config { + * 1 = use cryptobinding if server supports it + * 2 = require cryptobinding + * ++ * phase2_auth option can be used to control Phase 2 (i.e., within TLS ++ * tunnel) behavior for PEAP: ++ * 0 = do not require Phase 2 authentication ++ * 1 = require Phase 2 authentication when client certificate ++ * (private_key/client_cert) is no used and TLS session resumption was ++ * not used (default) ++ * 2 = require Phase 2 authentication in all cases ++ * + * EAP-WSC (WPS) uses following options: pin=Device_Password and + * uuid=Device_UUID + * +diff --git a/src/eap_peer/eap_peap.c b/src/eap_peer/eap_peap.c +index 12e30df..6080697 100644 +--- a/src/eap_peer/eap_peap.c ++++ b/src/eap_peer/eap_peap.c +@@ -67,6 +67,7 @@ struct eap_peap_data { + u8 cmk[20]; + int soh; /* Whether IF-TNCCS-SOH (Statement of Health; Microsoft NAP) + * is enabled. */ ++ enum { NO_AUTH, FOR_INITIAL, ALWAYS } phase2_auth; + }; + + +@@ -114,6 +115,19 @@ static void eap_peap_parse_phase1(struct eap_peap_data *data, + wpa_printf(MSG_DEBUG, "EAP-PEAP: Require cryptobinding"); + } + ++ if (os_strstr(phase1, "phase2_auth=0")) { ++ data->phase2_auth = NO_AUTH; ++ wpa_printf(MSG_DEBUG, ++ "EAP-PEAP: Do not require Phase 2 authentication"); ++ } else if (os_strstr(phase1, "phase2_auth=1")) { ++ data->phase2_auth = FOR_INITIAL; ++ wpa_printf(MSG_DEBUG, ++ "EAP-PEAP: Require Phase 2 authentication for initial connection"); ++ } else if (os_strstr(phase1, "phase2_auth=2")) { ++ data->phase2_auth = ALWAYS; ++ wpa_printf(MSG_DEBUG, ++ "EAP-PEAP: Require Phase 2 authentication for all cases"); ++ } + #ifdef EAP_TNC + if (os_strstr(phase1, "tnc=soh2")) { + data->soh = 2; +@@ -142,6 +156,7 @@ static void * eap_peap_init(struct eap_sm *sm) + data->force_peap_version = -1; + data->peap_outer_success = 2; + data->crypto_binding = OPTIONAL_BINDING; ++ data->phase2_auth = FOR_INITIAL; + + if (config && config->phase1) + eap_peap_parse_phase1(data, config->phase1); +@@ -454,6 +469,20 @@ static int eap_tlv_validate_cryptobinding(struct eap_sm *sm, + } + + ++static bool peap_phase2_sufficient(struct eap_sm *sm, ++ struct eap_peap_data *data) ++{ ++ if ((data->phase2_auth == ALWAYS || ++ (data->phase2_auth == FOR_INITIAL && ++ !tls_connection_resumed(sm->ssl_ctx, data->ssl.conn) && ++ !data->ssl.client_cert_conf) || ++ data->phase2_eap_started) && ++ !data->phase2_eap_success) ++ return false; ++ return true; ++} ++ ++ + /** + * eap_tlv_process - Process a received EAP-TLV message and generate a response + * @sm: Pointer to EAP state machine allocated with eap_peer_sm_init() +@@ -568,6 +597,11 @@ static int eap_tlv_process(struct eap_sm *sm, struct eap_peap_data *data, + " - force failed Phase 2"); + resp_status = EAP_TLV_RESULT_FAILURE; + ret->decision = DECISION_FAIL; ++ } else if (!peap_phase2_sufficient(sm, data)) { ++ wpa_printf(MSG_INFO, ++ "EAP-PEAP: Server indicated Phase 2 success, but sufficient Phase 2 authentication has not been completed"); ++ resp_status = EAP_TLV_RESULT_FAILURE; ++ ret->decision = DECISION_FAIL; + } else { + resp_status = EAP_TLV_RESULT_SUCCESS; + ret->decision = DECISION_UNCOND_SUCC; +@@ -887,8 +921,7 @@ continue_req: + /* EAP-Success within TLS tunnel is used to indicate + * shutdown of the TLS channel. The authentication has + * been completed. */ +- if (data->phase2_eap_started && +- !data->phase2_eap_success) { ++ if (!peap_phase2_sufficient(sm, data)) { + wpa_printf(MSG_DEBUG, "EAP-PEAP: Phase 2 " + "Success used to indicate success, " + "but Phase 2 EAP was not yet " +@@ -1199,8 +1232,9 @@ static struct wpabuf * eap_peap_process(struct eap_sm *sm, void *priv, + static bool eap_peap_has_reauth_data(struct eap_sm *sm, void *priv) + { + struct eap_peap_data *data = priv; ++ + return tls_connection_established(sm->ssl_ctx, data->ssl.conn) && +- data->phase2_success; ++ data->phase2_success && data->phase2_auth != ALWAYS; + } + + +diff --git a/src/eap_peer/eap_tls_common.c b/src/eap_peer/eap_tls_common.c +index c1837db..a53eeb1 100644 +--- a/src/eap_peer/eap_tls_common.c ++++ b/src/eap_peer/eap_tls_common.c +@@ -239,6 +239,12 @@ static int eap_tls_params_from_conf(struct eap_sm *sm, + + sm->ext_cert_check = !!(params->flags & TLS_CONN_EXT_CERT_CHECK); + ++ if (!phase2) ++ data->client_cert_conf = params->client_cert || ++ params->client_cert_blob || ++ params->private_key || ++ params->private_key_blob; ++ + return 0; + } + +diff --git a/src/eap_peer/eap_tls_common.h b/src/eap_peer/eap_tls_common.h +index 9ac0012..3348634 100644 +--- a/src/eap_peer/eap_tls_common.h ++++ b/src/eap_peer/eap_tls_common.h +@@ -79,6 +79,11 @@ struct eap_ssl_data { + * tls_v13 - Whether TLS v1.3 or newer is used + */ + int tls_v13; ++ ++ /** ++ * client_cert_conf: Whether client certificate has been configured ++ */ ++ bool client_cert_conf; + }; + + +diff --git a/wpa_supplicant/wpa_supplicant.conf b/wpa_supplicant/wpa_supplicant.conf +index 6619d6b..d63f73c 100644 +--- a/wpa_supplicant/wpa_supplicant.conf ++++ b/wpa_supplicant/wpa_supplicant.conf +@@ -1321,6 +1321,13 @@ fast_reauth=1 + # * 0 = do not use cryptobinding (default) + # * 1 = use cryptobinding if server supports it + # * 2 = require cryptobinding ++# 'phase2_auth' option can be used to control Phase 2 (i.e., within TLS ++# tunnel) behavior for PEAP: ++# * 0 = do not require Phase 2 authentication ++# * 1 = require Phase 2 authentication when client certificate ++# (private_key/client_cert) is no used and TLS session resumption was ++# not used (default) ++# * 2 = require Phase 2 authentication in all cases + # EAP-WSC (WPS) uses following options: pin=<Device Password> or + # pbc=1. + # diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-build-Re-enable-options-for-libwpa_client.so-and-wpa.patch b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-build-Re-enable-options-for-libwpa_client.so-and-wpa.patch new file mode 100644 index 0000000000..6e930fc98d --- /dev/null +++ b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-build-Re-enable-options-for-libwpa_client.so-and-wpa.patch @@ -0,0 +1,73 @@ +From cb41c214b78d6df187a31950342e48a403dbd769 Mon Sep 17 00:00:00 2001 +From: Sergey Matyukevich <geomatsi@gmail.com> +Date: Tue, 22 Feb 2022 11:52:19 +0300 +Subject: [PATCH 1/2] build: Re-enable options for libwpa_client.so and + wpa_passphrase + +Commit a41a29192e5d ("build: Pull common fragments into a build.rules +file") introduced a regression into wpa_supplicant build process. The +build target libwpa_client.so is not built regardless of whether the +option CONFIG_BUILD_WPA_CLIENT_SO is set or not. This happens because +this config option is used before it is imported from the configuration +file. Moving its use after including build.rules does not help: the +variable ALL is processed by build.rules and further changes are not +applied. Similarly, option CONFIG_NO_WPA_PASSPHRASE also does not work +as expected: wpa_passphrase is always built regardless of whether the +option is set or not. + +Re-enable these options by adding both build targets to _all +dependencies. + +Fixes: a41a29192e5d ("build: Pull common fragments into a build.rules file") +Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com> +Upstream-Status: Backport +Signed-off-by: Alex Kiernan <alexk@zuma.ai> +Signed-off-by: Alex Kiernan <alexk@gmail.com> +--- + wpa_supplicant/Makefile | 19 ++++++++++++------- + 1 file changed, 12 insertions(+), 7 deletions(-) + +diff --git a/wpa_supplicant/Makefile b/wpa_supplicant/Makefile +index cb66defac7c8..c456825ae75f 100644 +--- a/wpa_supplicant/Makefile ++++ b/wpa_supplicant/Makefile +@@ -1,24 +1,29 @@ + BINALL=wpa_supplicant wpa_cli + +-ifndef CONFIG_NO_WPA_PASSPHRASE +-BINALL += wpa_passphrase +-endif +- + ALL = $(BINALL) + ALL += systemd/wpa_supplicant.service + ALL += systemd/wpa_supplicant@.service + ALL += systemd/wpa_supplicant-nl80211@.service + ALL += systemd/wpa_supplicant-wired@.service + ALL += dbus/fi.w1.wpa_supplicant1.service +-ifdef CONFIG_BUILD_WPA_CLIENT_SO +-ALL += libwpa_client.so +-endif + + EXTRA_TARGETS=dynamic_eap_methods + + CONFIG_FILE=.config + include ../src/build.rules + ++ifdef CONFIG_BUILD_WPA_CLIENT_SO ++# add the dependency this way to allow CONFIG_BUILD_WPA_CLIENT_SO ++# being set in the config which is read by build.rules ++_all: libwpa_client.so ++endif ++ ++ifndef CONFIG_NO_WPA_PASSPHRASE ++# add the dependency this way to allow CONFIG_NO_WPA_PASSPHRASE ++# being set in the config which is read by build.rules ++_all: wpa_passphrase ++endif ++ + ifdef LIBS + # If LIBS is set with some global build system defaults, clone those for + # LIBS_c and LIBS_p to cover wpa_passphrase and wpa_cli as well. +-- +2.35.1 + diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-replace-systemd-install-Alias-with-WantedBy.patch b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-replace-systemd-install-Alias-with-WantedBy.patch deleted file mode 100644 index a476cf040e..0000000000 --- a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0001-replace-systemd-install-Alias-with-WantedBy.patch +++ /dev/null @@ -1,52 +0,0 @@ -From 94c401733a5a3d294cc412671166e6adfb409f53 Mon Sep 17 00:00:00 2001 -From: Joshua DeWeese <jdeweese@hennypenny.com> -Date: Wed, 30 Jan 2019 16:19:47 -0500 -Subject: [PATCH] replace systemd install Alias with WantedBy - -According to the systemd documentation "WantedBy=foo.service in a -service bar.service is mostly equivalent to -Alias=foo.service.wants/bar.service in the same file." However, -this is not really the intended purpose of install Aliases. - -Upstream-Status: Submitted [hostap@lists.infradead.org] - -Signed-off-by: Joshua DeWeese <jdeweese@hennypenny.com> ---- - wpa_supplicant/systemd/wpa_supplicant-nl80211.service.arg.in | 2 +- - wpa_supplicant/systemd/wpa_supplicant-wired.service.arg.in | 2 +- - wpa_supplicant/systemd/wpa_supplicant.service.arg.in | 2 +- - 3 files changed, 3 insertions(+), 3 deletions(-) - -diff --git a/wpa_supplicant/systemd/wpa_supplicant-nl80211.service.arg.in b/wpa_supplicant/systemd/wpa_supplicant-nl80211.service.arg.in -index 03ac507..da69a87 100644 ---- a/wpa_supplicant/systemd/wpa_supplicant-nl80211.service.arg.in -+++ b/wpa_supplicant/systemd/wpa_supplicant-nl80211.service.arg.in -@@ -12,4 +12,4 @@ Type=simple - ExecStart=@BINDIR@/wpa_supplicant -c/etc/wpa_supplicant/wpa_supplicant-nl80211-%I.conf -Dnl80211 -i%I - - [Install] --Alias=multi-user.target.wants/wpa_supplicant-nl80211@%i.service -+WantedBy=multi-user.target -diff --git a/wpa_supplicant/systemd/wpa_supplicant-wired.service.arg.in b/wpa_supplicant/systemd/wpa_supplicant-wired.service.arg.in -index c8a744d..ca3054b 100644 ---- a/wpa_supplicant/systemd/wpa_supplicant-wired.service.arg.in -+++ b/wpa_supplicant/systemd/wpa_supplicant-wired.service.arg.in -@@ -12,4 +12,4 @@ Type=simple - ExecStart=@BINDIR@/wpa_supplicant -c/etc/wpa_supplicant/wpa_supplicant-wired-%I.conf -Dwired -i%I - - [Install] --Alias=multi-user.target.wants/wpa_supplicant-wired@%i.service -+WantedBy=multi-user.target -diff --git a/wpa_supplicant/systemd/wpa_supplicant.service.arg.in b/wpa_supplicant/systemd/wpa_supplicant.service.arg.in -index 7788b38..55d2b9c 100644 ---- a/wpa_supplicant/systemd/wpa_supplicant.service.arg.in -+++ b/wpa_supplicant/systemd/wpa_supplicant.service.arg.in -@@ -12,4 +12,4 @@ Type=simple - ExecStart=@BINDIR@/wpa_supplicant -c/etc/wpa_supplicant/wpa_supplicant-%I.conf -i%I - - [Install] --Alias=multi-user.target.wants/wpa_supplicant@%i.service -+WantedBy=multi-user.target --- -2.7.4 - diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0002-Fix-removal-of-wpa_passphrase-on-make-clean.patch b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0002-Fix-removal-of-wpa_passphrase-on-make-clean.patch new file mode 100644 index 0000000000..53b0fcdf53 --- /dev/null +++ b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/0002-Fix-removal-of-wpa_passphrase-on-make-clean.patch @@ -0,0 +1,26 @@ +From d001b301ba7987f4b39453a211631b85c48f2ff8 Mon Sep 17 00:00:00 2001 +From: Jouni Malinen <quic_jouni@quicinc.com> +Date: Thu, 3 Mar 2022 13:26:42 +0200 +Subject: [PATCH 2/2] Fix removal of wpa_passphrase on 'make clean' + +Fixes: 0430bc8267b4 ("build: Add a common-clean target") +Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com> +Upstream-Status: Backport +Signed-off-by: Alex Kiernan <alexk@zuma.ai> +Signed-off-by: Alex Kiernan <alexk@gmail.com> +--- + wpa_supplicant/Makefile | 1 + + 1 file changed, 1 insertion(+) + +diff --git a/wpa_supplicant/Makefile b/wpa_supplicant/Makefile +index c456825ae75f..4b4688931b1d 100644 +--- a/wpa_supplicant/Makefile ++++ b/wpa_supplicant/Makefile +@@ -2077,3 +2077,4 @@ clean: common-clean + rm -f libwpa_client.a + rm -f libwpa_client.so + rm -f libwpa_test1 libwpa_test2 ++ rm -f wpa_passphrase +-- +2.35.1 + diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/defconfig b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/defconfig deleted file mode 100644 index f04e398fdb..0000000000 --- a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant/defconfig +++ /dev/null @@ -1,552 +0,0 @@ -# Example wpa_supplicant build time configuration -# -# This file lists the configuration options that are used when building the -# hostapd binary. All lines starting with # are ignored. Configuration option -# lines must be commented out complete, if they are not to be included, i.e., -# just setting VARIABLE=n is not disabling that variable. -# -# This file is included in Makefile, so variables like CFLAGS and LIBS can also -# be modified from here. In most cases, these lines should use += in order not -# to override previous values of the variables. - - -# Uncomment following two lines and fix the paths if you have installed OpenSSL -# or GnuTLS in non-default location -#CFLAGS += -I/usr/local/openssl/include -#LIBS += -L/usr/local/openssl/lib - -# Some Red Hat versions seem to include kerberos header files from OpenSSL, but -# the kerberos files are not in the default include path. Following line can be -# used to fix build issues on such systems (krb5.h not found). -#CFLAGS += -I/usr/include/kerberos - -# Example configuration for various cross-compilation platforms - -#### sveasoft (e.g., for Linksys WRT54G) ###################################### -#CC=mipsel-uclibc-gcc -#CC=/opt/brcm/hndtools-mipsel-uclibc/bin/mipsel-uclibc-gcc -#CFLAGS += -Os -#CPPFLAGS += -I../src/include -I../../src/router/openssl/include -#LIBS += -L/opt/brcm/hndtools-mipsel-uclibc-0.9.19/lib -lssl -############################################################################### - -#### openwrt (e.g., for Linksys WRT54G) ####################################### -#CC=mipsel-uclibc-gcc -#CC=/opt/brcm/hndtools-mipsel-uclibc/bin/mipsel-uclibc-gcc -#CFLAGS += -Os -#CPPFLAGS=-I../src/include -I../openssl-0.9.7d/include \ -# -I../WRT54GS/release/src/include -#LIBS = -lssl -############################################################################### - - -# Driver interface for Host AP driver -CONFIG_DRIVER_HOSTAP=y - -# Driver interface for Agere driver -#CONFIG_DRIVER_HERMES=y -# Change include directories to match with the local setup -#CFLAGS += -I../../hcf -I../../include -I../../include/hcf -#CFLAGS += -I../../include/wireless - -# Driver interface for madwifi driver -# Deprecated; use CONFIG_DRIVER_WEXT=y instead. -#CONFIG_DRIVER_MADWIFI=y -# Set include directory to the madwifi source tree -#CFLAGS += -I../../madwifi - -# Driver interface for ndiswrapper -# Deprecated; use CONFIG_DRIVER_WEXT=y instead. -#CONFIG_DRIVER_NDISWRAPPER=y - -# Driver interface for Atmel driver -# CONFIG_DRIVER_ATMEL=y - -# Driver interface for old Broadcom driver -# Please note that the newer Broadcom driver ("hybrid Linux driver") supports -# Linux wireless extensions and does not need (or even work) with the old -# driver wrapper. Use CONFIG_DRIVER_WEXT=y with that driver. -#CONFIG_DRIVER_BROADCOM=y -# Example path for wlioctl.h; change to match your configuration -#CFLAGS += -I/opt/WRT54GS/release/src/include - -# Driver interface for Intel ipw2100/2200 driver -# Deprecated; use CONFIG_DRIVER_WEXT=y instead. -#CONFIG_DRIVER_IPW=y - -# Driver interface for Ralink driver -#CONFIG_DRIVER_RALINK=y - -# Driver interface for generic Linux wireless extensions -# Note: WEXT is deprecated in the current Linux kernel version and no new -# functionality is added to it. nl80211-based interface is the new -# replacement for WEXT and its use allows wpa_supplicant to properly control -# the driver to improve existing functionality like roaming and to support new -# functionality. -CONFIG_DRIVER_WEXT=y - -# Driver interface for Linux drivers using the nl80211 kernel interface -CONFIG_DRIVER_NL80211=y - -# driver_nl80211.c requires libnl. If you are compiling it yourself -# you may need to point hostapd to your version of libnl. -# -#CFLAGS += -I$<path to libnl include files> -#LIBS += -L$<path to libnl library files> - -# Use libnl v2.0 (or 3.0) libraries. -#CONFIG_LIBNL20=y - -# Use libnl 3.2 libraries (if this is selected, CONFIG_LIBNL20 is ignored) -CONFIG_LIBNL32=y - - -# Driver interface for FreeBSD net80211 layer (e.g., Atheros driver) -#CONFIG_DRIVER_BSD=y -#CFLAGS += -I/usr/local/include -#LIBS += -L/usr/local/lib -#LIBS_p += -L/usr/local/lib -#LIBS_c += -L/usr/local/lib - -# Driver interface for Windows NDIS -#CONFIG_DRIVER_NDIS=y -#CFLAGS += -I/usr/include/w32api/ddk -#LIBS += -L/usr/local/lib -# For native build using mingw -#CONFIG_NATIVE_WINDOWS=y -# Additional directories for cross-compilation on Linux host for mingw target -#CFLAGS += -I/opt/mingw/mingw32/include/ddk -#LIBS += -L/opt/mingw/mingw32/lib -#CC=mingw32-gcc -# By default, driver_ndis uses WinPcap for low-level operations. This can be -# replaced with the following option which replaces WinPcap calls with NDISUIO. -# However, this requires that WZC is disabled (net stop wzcsvc) before starting -# wpa_supplicant. -# CONFIG_USE_NDISUIO=y - -# Driver interface for development testing -#CONFIG_DRIVER_TEST=y - -# Driver interface for wired Ethernet drivers -CONFIG_DRIVER_WIRED=y - -# Driver interface for the Broadcom RoboSwitch family -#CONFIG_DRIVER_ROBOSWITCH=y - -# Driver interface for no driver (e.g., WPS ER only) -#CONFIG_DRIVER_NONE=y - -# Enable IEEE 802.1X Supplicant (automatically included if any EAP method is -# included) -CONFIG_IEEE8021X_EAPOL=y - -# EAP-MD5 -CONFIG_EAP_MD5=y - -# EAP-MSCHAPv2 -CONFIG_EAP_MSCHAPV2=y - -# EAP-TLS -CONFIG_EAP_TLS=y - -# EAL-PEAP -CONFIG_EAP_PEAP=y - -# EAP-TTLS -CONFIG_EAP_TTLS=y - -# EAP-FAST -# Note: If OpenSSL is used as the TLS library, OpenSSL 1.0 or newer is needed -# for EAP-FAST support. Older OpenSSL releases would need to be patched, e.g., -# with openssl-0.9.8x-tls-extensions.patch, to add the needed functions. -#CONFIG_EAP_FAST=y - -# EAP-GTC -CONFIG_EAP_GTC=y - -# EAP-OTP -CONFIG_EAP_OTP=y - -# EAP-SIM (enable CONFIG_PCSC, if EAP-SIM is used) -#CONFIG_EAP_SIM=y - -# EAP-PSK (experimental; this is _not_ needed for WPA-PSK) -#CONFIG_EAP_PSK=y - -# EAP-pwd (secure authentication using only a password) -#CONFIG_EAP_PWD=y - -# EAP-PAX -#CONFIG_EAP_PAX=y - -# LEAP -CONFIG_EAP_LEAP=y - -# EAP-AKA (enable CONFIG_PCSC, if EAP-AKA is used) -#CONFIG_EAP_AKA=y - -# EAP-AKA' (enable CONFIG_PCSC, if EAP-AKA' is used). -# This requires CONFIG_EAP_AKA to be enabled, too. -#CONFIG_EAP_AKA_PRIME=y - -# Enable USIM simulator (Milenage) for EAP-AKA -#CONFIG_USIM_SIMULATOR=y - -# EAP-SAKE -#CONFIG_EAP_SAKE=y - -# EAP-GPSK -#CONFIG_EAP_GPSK=y -# Include support for optional SHA256 cipher suite in EAP-GPSK -#CONFIG_EAP_GPSK_SHA256=y - -# EAP-TNC and related Trusted Network Connect support (experimental) -#CONFIG_EAP_TNC=y - -# Wi-Fi Protected Setup (WPS) -CONFIG_WPS=y -# Enable WSC 2.0 support -#CONFIG_WPS2=y -# Enable WPS external registrar functionality -#CONFIG_WPS_ER=y -# Disable credentials for an open network by default when acting as a WPS -# registrar. -#CONFIG_WPS_REG_DISABLE_OPEN=y -# Enable WPS support with NFC config method -#CONFIG_WPS_NFC=y - -# EAP-IKEv2 -#CONFIG_EAP_IKEV2=y - -# EAP-EKE -#CONFIG_EAP_EKE=y - -# PKCS#12 (PFX) support (used to read private key and certificate file from -# a file that usually has extension .p12 or .pfx) -CONFIG_PKCS12=y - -# Smartcard support (i.e., private key on a smartcard), e.g., with openssl -# engine. -CONFIG_SMARTCARD=y - -# PC/SC interface for smartcards (USIM, GSM SIM) -# Enable this if EAP-SIM or EAP-AKA is included -#CONFIG_PCSC=y - -# Support HT overrides (disable HT/HT40, mask MCS rates, etc.) -#CONFIG_HT_OVERRIDES=y - -# Support VHT overrides (disable VHT, mask MCS rates, etc.) -#CONFIG_VHT_OVERRIDES=y - -# Development testing -#CONFIG_EAPOL_TEST=y - -# Select control interface backend for external programs, e.g, wpa_cli: -# unix = UNIX domain sockets (default for Linux/*BSD) -# udp = UDP sockets using localhost (127.0.0.1) -# named_pipe = Windows Named Pipe (default for Windows) -# udp-remote = UDP sockets with remote access (only for tests systems/purpose) -# y = use default (backwards compatibility) -# If this option is commented out, control interface is not included in the -# build. -CONFIG_CTRL_IFACE=y - -# Include support for GNU Readline and History Libraries in wpa_cli. -# When building a wpa_cli binary for distribution, please note that these -# libraries are licensed under GPL and as such, BSD license may not apply for -# the resulting binary. -#CONFIG_READLINE=y - -# Include internal line edit mode in wpa_cli. This can be used as a replacement -# for GNU Readline to provide limited command line editing and history support. -#CONFIG_WPA_CLI_EDIT=y - -# Remove debugging code that is printing out debug message to stdout. -# This can be used to reduce the size of the wpa_supplicant considerably -# if debugging code is not needed. The size reduction can be around 35% -# (e.g., 90 kB). -#CONFIG_NO_STDOUT_DEBUG=y - -# Remove WPA support, e.g., for wired-only IEEE 802.1X supplicant, to save -# 35-50 kB in code size. -#CONFIG_NO_WPA=y - -# Remove IEEE 802.11i/WPA-Personal ASCII passphrase support -# This option can be used to reduce code size by removing support for -# converting ASCII passphrases into PSK. If this functionality is removed, the -# PSK can only be configured as the 64-octet hexstring (e.g., from -# wpa_passphrase). This saves about 0.5 kB in code size. -#CONFIG_NO_WPA_PASSPHRASE=y - -# Disable scan result processing (ap_mode=1) to save code size by about 1 kB. -# This can be used if ap_scan=1 mode is never enabled. -#CONFIG_NO_SCAN_PROCESSING=y - -# Select configuration backend: -# file = text file (e.g., wpa_supplicant.conf; note: the configuration file -# path is given on command line, not here; this option is just used to -# select the backend that allows configuration files to be used) -# winreg = Windows registry (see win_example.reg for an example) -CONFIG_BACKEND=file - -# Remove configuration write functionality (i.e., to allow the configuration -# file to be updated based on runtime configuration changes). The runtime -# configuration can still be changed, the changes are just not going to be -# persistent over restarts. This option can be used to reduce code size by -# about 3.5 kB. -#CONFIG_NO_CONFIG_WRITE=y - -# Remove support for configuration blobs to reduce code size by about 1.5 kB. -#CONFIG_NO_CONFIG_BLOBS=y - -# Select program entry point implementation: -# main = UNIX/POSIX like main() function (default) -# main_winsvc = Windows service (read parameters from registry) -# main_none = Very basic example (development use only) -#CONFIG_MAIN=main - -# Select wrapper for operatins system and C library specific functions -# unix = UNIX/POSIX like systems (default) -# win32 = Windows systems -# none = Empty template -#CONFIG_OS=unix - -# Select event loop implementation -# eloop = select() loop (default) -# eloop_win = Windows events and WaitForMultipleObject() loop -#CONFIG_ELOOP=eloop - -# Should we use poll instead of select? Select is used by default. -#CONFIG_ELOOP_POLL=y - -# Select layer 2 packet implementation -# linux = Linux packet socket (default) -# pcap = libpcap/libdnet/WinPcap -# freebsd = FreeBSD libpcap -# winpcap = WinPcap with receive thread -# ndis = Windows NDISUIO (note: requires CONFIG_USE_NDISUIO=y) -# none = Empty template -#CONFIG_L2_PACKET=linux - -# PeerKey handshake for Station to Station Link (IEEE 802.11e DLS) -CONFIG_PEERKEY=y - -# IEEE 802.11w (management frame protection), also known as PMF -# Driver support is also needed for IEEE 802.11w. -#CONFIG_IEEE80211W=y - -# Select TLS implementation -# openssl = OpenSSL (default) -# gnutls = GnuTLS -# internal = Internal TLSv1 implementation (experimental) -# none = Empty template -#CONFIG_TLS=openssl - -# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.1) -# can be enabled to get a stronger construction of messages when block ciphers -# are used. It should be noted that some existing TLS v1.0 -based -# implementation may not be compatible with TLS v1.1 message (ClientHello is -# sent prior to negotiating which version will be used) -#CONFIG_TLSV11=y - -# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.2) -# can be enabled to enable use of stronger crypto algorithms. It should be -# noted that some existing TLS v1.0 -based implementation may not be compatible -# with TLS v1.2 message (ClientHello is sent prior to negotiating which version -# will be used) -#CONFIG_TLSV12=y - -# If CONFIG_TLS=internal is used, additional library and include paths are -# needed for LibTomMath. Alternatively, an integrated, minimal version of -# LibTomMath can be used. See beginning of libtommath.c for details on benefits -# and drawbacks of this option. -#CONFIG_INTERNAL_LIBTOMMATH=y -#ifndef CONFIG_INTERNAL_LIBTOMMATH -#LTM_PATH=/usr/src/libtommath-0.39 -#CFLAGS += -I$(LTM_PATH) -#LIBS += -L$(LTM_PATH) -#LIBS_p += -L$(LTM_PATH) -#endif -# At the cost of about 4 kB of additional binary size, the internal LibTomMath -# can be configured to include faster routines for exptmod, sqr, and div to -# speed up DH and RSA calculation considerably -#CONFIG_INTERNAL_LIBTOMMATH_FAST=y - -# Include NDIS event processing through WMI into wpa_supplicant/wpasvc. -# This is only for Windows builds and requires WMI-related header files and -# WbemUuid.Lib from Platform SDK even when building with MinGW. -#CONFIG_NDIS_EVENTS_INTEGRATED=y -#PLATFORMSDKLIB="/opt/Program Files/Microsoft Platform SDK/Lib" - -# Add support for old DBus control interface -# (fi.epitest.hostap.WPASupplicant) -#CONFIG_CTRL_IFACE_DBUS=y - -# Add support for new DBus control interface -# (fi.w1.hostap.wpa_supplicant1) -CONFIG_CTRL_IFACE_DBUS_NEW=y - -# Add introspection support for new DBus control interface -#CONFIG_CTRL_IFACE_DBUS_INTRO=y - -# Add support for loading EAP methods dynamically as shared libraries. -# When this option is enabled, each EAP method can be either included -# statically (CONFIG_EAP_<method>=y) or dynamically (CONFIG_EAP_<method>=dyn). -# Dynamic EAP methods are build as shared objects (eap_*.so) and they need to -# be loaded in the beginning of the wpa_supplicant configuration file -# (see load_dynamic_eap parameter in the example file) before being used in -# the network blocks. -# -# Note that some shared parts of EAP methods are included in the main program -# and in order to be able to use dynamic EAP methods using these parts, the -# main program must have been build with the EAP method enabled (=y or =dyn). -# This means that EAP-TLS/PEAP/TTLS/FAST cannot be added as dynamic libraries -# unless at least one of them was included in the main build to force inclusion -# of the shared code. Similarly, at least one of EAP-SIM/AKA must be included -# in the main build to be able to load these methods dynamically. -# -# Please also note that using dynamic libraries will increase the total binary -# size. Thus, it may not be the best option for targets that have limited -# amount of memory/flash. -#CONFIG_DYNAMIC_EAP_METHODS=y - -# IEEE Std 802.11r-2008 (Fast BSS Transition) -#CONFIG_IEEE80211R=y - -# Add support for writing debug log to a file (/tmp/wpa_supplicant-log-#.txt) -#CONFIG_DEBUG_FILE=y - -# Send debug messages to syslog instead of stdout -#CONFIG_DEBUG_SYSLOG=y -# Set syslog facility for debug messages -#CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON - -# Add support for sending all debug messages (regardless of debug verbosity) -# to the Linux kernel tracing facility. This helps debug the entire stack by -# making it easy to record everything happening from the driver up into the -# same file, e.g., using trace-cmd. -#CONFIG_DEBUG_LINUX_TRACING=y - -# Enable privilege separation (see README 'Privilege separation' for details) -#CONFIG_PRIVSEP=y - -# Enable mitigation against certain attacks against TKIP by delaying Michael -# MIC error reports by a random amount of time between 0 and 60 seconds -#CONFIG_DELAYED_MIC_ERROR_REPORT=y - -# Enable tracing code for developer debugging -# This tracks use of memory allocations and other registrations and reports -# incorrect use with a backtrace of call (or allocation) location. -#CONFIG_WPA_TRACE=y -# For BSD, uncomment these. -#LIBS += -lexecinfo -#LIBS_p += -lexecinfo -#LIBS_c += -lexecinfo - -# Use libbfd to get more details for developer debugging -# This enables use of libbfd to get more detailed symbols for the backtraces -# generated by CONFIG_WPA_TRACE=y. -#CONFIG_WPA_TRACE_BFD=y -# For BSD, uncomment these. -#LIBS += -lbfd -liberty -lz -#LIBS_p += -lbfd -liberty -lz -#LIBS_c += -lbfd -liberty -lz - -CONFIG_TLS = %ssl% -CONFIG_CTRL_IFACE_DBUS=y -CONFIG_CTRL_IFACE_DBUS_NEW=y - -# wpa_supplicant depends on strong random number generation being available -# from the operating system. os_get_random() function is used to fetch random -# data when needed, e.g., for key generation. On Linux and BSD systems, this -# works by reading /dev/urandom. It should be noted that the OS entropy pool -# needs to be properly initialized before wpa_supplicant is started. This is -# important especially on embedded devices that do not have a hardware random -# number generator and may by default start up with minimal entropy available -# for random number generation. -# -# As a safety net, wpa_supplicant is by default trying to internally collect -# additional entropy for generating random data to mix in with the data fetched -# from the OS. This by itself is not considered to be very strong, but it may -# help in cases where the system pool is not initialized properly. However, it -# is very strongly recommended that the system pool is initialized with enough -# entropy either by using hardware assisted random number generator or by -# storing state over device reboots. -# -# wpa_supplicant can be configured to maintain its own entropy store over -# restarts to enhance random number generation. This is not perfect, but it is -# much more secure than using the same sequence of random numbers after every -# reboot. This can be enabled with -e<entropy file> command line option. The -# specified file needs to be readable and writable by wpa_supplicant. -# -# If the os_get_random() is known to provide strong random data (e.g., on -# Linux/BSD, the board in question is known to have reliable source of random -# data from /dev/urandom), the internal wpa_supplicant random pool can be -# disabled. This will save some in binary size and CPU use. However, this -# should only be considered for builds that are known to be used on devices -# that meet the requirements described above. -#CONFIG_NO_RANDOM_POOL=y - -# IEEE 802.11n (High Throughput) support (mainly for AP mode) -#CONFIG_IEEE80211N=y - -# IEEE 802.11ac (Very High Throughput) support (mainly for AP mode) -# (depends on CONFIG_IEEE80211N) -#CONFIG_IEEE80211AC=y - -# Wireless Network Management (IEEE Std 802.11v-2011) -# Note: This is experimental and not complete implementation. -#CONFIG_WNM=y - -# Interworking (IEEE 802.11u) -# This can be used to enable functionality to improve interworking with -# external networks (GAS/ANQP to learn more about the networks and network -# selection based on available credentials). -#CONFIG_INTERWORKING=y - -# Hotspot 2.0 -#CONFIG_HS20=y - -# Disable roaming in wpa_supplicant -#CONFIG_NO_ROAMING=y - -# AP mode operations with wpa_supplicant -# This can be used for controlling AP mode operations with wpa_supplicant. It -# should be noted that this is mainly aimed at simple cases like -# WPA2-Personal while more complex configurations like WPA2-Enterprise with an -# external RADIUS server can be supported with hostapd. -CONFIG_AP=y - -CONFIG_BGSCAN_SIMPLE=y - -# P2P (Wi-Fi Direct) -# This can be used to enable P2P support in wpa_supplicant. See README-P2P for -# more information on P2P operations. -#CONFIG_P2P=y - -# Enable TDLS support -#CONFIG_TDLS=y - -# Wi-Fi Direct -# This can be used to enable Wi-Fi Direct extensions for P2P using an external -# program to control the additional information exchanges in the messages. -#CONFIG_WIFI_DISPLAY=y - -# Autoscan -# This can be used to enable automatic scan support in wpa_supplicant. -# See wpa_supplicant.conf for more information on autoscan usage. -# -# Enabling directly a module will enable autoscan support. -# For exponential module: -CONFIG_AUTOSCAN_EXPONENTIAL=y -# For periodic module: -#CONFIG_AUTOSCAN_PERIODIC=y - -# Password (and passphrase, etc.) backend for external storage -# These optional mechanisms can be used to add support for storing passwords -# and other secrets in external (to wpa_supplicant) location. This allows, for -# example, operating system specific key storage to be used -# -# External password backend for testing purposes (developer use) -#CONFIG_EXT_PASSWORD_TEST=y diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.10.bb b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.10.bb new file mode 100644 index 0000000000..8113bcab09 --- /dev/null +++ b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.10.bb @@ -0,0 +1,138 @@ +SUMMARY = "Client for Wi-Fi Protected Access (WPA)" +DESCRIPTION = "wpa_supplicant is a WPA Supplicant for Linux, BSD, Mac OS X, and Windows with support for WPA and WPA2 (IEEE 802.11i / RSN). Supplicant is the IEEE 802.1X/WPA component that is used in the client stations. It implements key negotiation with a WPA Authenticator and it controls the roaming and IEEE 802.11 authentication/association of the wlan driver." +HOMEPAGE = "http://w1.fi/wpa_supplicant/" +BUGTRACKER = "http://w1.fi/security/" +SECTION = "network" +LICENSE = "BSD-3-Clause" +LIC_FILES_CHKSUM = "file://COPYING;md5=5ebcb90236d1ad640558c3d3cd3035df \ + file://README;beginline=1;endline=56;md5=e3d2f6c2948991e37c1ca4960de84747 \ + file://wpa_supplicant/wpa_supplicant.c;beginline=1;endline=12;md5=76306a95306fee9a976b0ac1be70f705" + +DEPENDS = "dbus libnl" + +SRC_URI = "http://w1.fi/releases/wpa_supplicant-${PV}.tar.gz \ + file://wpa-supplicant.sh \ + file://wpa_supplicant.conf \ + file://wpa_supplicant.conf-sane \ + file://99_wpa_supplicant \ + file://0001-build-Re-enable-options-for-libwpa_client.so-and-wpa.patch \ + file://0002-Fix-removal-of-wpa_passphrase-on-make-clean.patch \ + file://0001-Install-wpa_passphrase-when-not-disabled.patch \ + file://0001-PEAP-client-Update-Phase-2-authentication-requiremen.patch \ + " +SRC_URI[sha256sum] = "20df7ae5154b3830355f8ab4269123a87affdea59fe74fe9292a91d0d7e17b2f" + +S = "${WORKDIR}/wpa_supplicant-${PV}" + +inherit pkgconfig systemd + +PACKAGECONFIG ?= "openssl" +PACKAGECONFIG[gnutls] = ",,gnutls libgcrypt" +PACKAGECONFIG[openssl] = ",,openssl" + +CVE_PRODUCT = "wpa_supplicant" + +EXTRA_OEMAKE = "'LIBDIR=${libdir}' 'INCDIR=${includedir}' 'BINDIR=${sbindir}'" + +do_configure () { + ${MAKE} -C wpa_supplicant clean + sed -e '/^CONFIG_TLS=/d' <wpa_supplicant/defconfig >wpa_supplicant/.config + + if ${@ bb.utils.contains('PACKAGECONFIG', 'openssl', 'true', 'false', d) }; then + echo 'CONFIG_TLS=openssl' >>wpa_supplicant/.config + elif ${@ bb.utils.contains('PACKAGECONFIG', 'gnutls', 'true', 'false', d) }; then + echo 'CONFIG_TLS=gnutls' >>wpa_supplicant/.config + sed -i -e 's/\(^CONFIG_DPP=\)/#\1/' \ + -e 's/\(^CONFIG_EAP_PWD=\)/#\1/' \ + -e 's/\(^CONFIG_SAE=\)/#\1/' wpa_supplicant/.config + fi + + # For rebuild + rm -f wpa_supplicant/*.d wpa_supplicant/dbus/*.d +} + +do_compile () { + oe_runmake -C wpa_supplicant + if [ -z "${DISABLE_STATIC}" ]; then + oe_runmake -C wpa_supplicant libwpa_client.a + fi +} + +do_install () { + oe_runmake -C wpa_supplicant DESTDIR="${D}" install + + install -d ${D}${docdir}/wpa_supplicant + install -m 644 wpa_supplicant/README ${UNPACKDIR}/wpa_supplicant.conf ${D}${docdir}/wpa_supplicant + + install -d ${D}${sysconfdir} + install -m 600 ${UNPACKDIR}/wpa_supplicant.conf-sane ${D}${sysconfdir}/wpa_supplicant.conf + + install -d ${D}${sysconfdir}/network/if-pre-up.d/ + install -d ${D}${sysconfdir}/network/if-post-down.d/ + install -d ${D}${sysconfdir}/network/if-down.d/ + install -m 755 ${UNPACKDIR}/wpa-supplicant.sh ${D}${sysconfdir}/network/if-pre-up.d/wpa-supplicant + ln -sf ../if-pre-up.d/wpa-supplicant ${D}${sysconfdir}/network/if-post-down.d/wpa-supplicant + + install -d ${D}/${sysconfdir}/dbus-1/system.d + install -m 644 ${S}/wpa_supplicant/dbus/dbus-wpa_supplicant.conf ${D}/${sysconfdir}/dbus-1/system.d + install -d ${D}/${datadir}/dbus-1/system-services + install -m 644 ${S}/wpa_supplicant/dbus/*.service ${D}/${datadir}/dbus-1/system-services + + if ${@bb.utils.contains('DISTRO_FEATURES','systemd','true','false',d)}; then + install -d ${D}/${systemd_system_unitdir} + install -m 644 ${S}/wpa_supplicant/systemd/*.service ${D}/${systemd_system_unitdir} + fi + + install -d ${D}/etc/default/volatiles + install -m 0644 ${UNPACKDIR}/99_wpa_supplicant ${D}/etc/default/volatiles + + install -d ${D}${includedir} + install -m 0644 ${S}/src/common/wpa_ctrl.h ${D}${includedir} + + if [ -z "${DISABLE_STATIC}" ]; then + install -d ${D}${libdir} + install -m 0644 wpa_supplicant/libwpa_client.a ${D}${libdir} + fi +} + +pkg_postinst:${PN} () { + # If we're offline, we don't need to do this. + if [ "x$D" = "x" ]; then + killall -q -HUP dbus-daemon || true + fi +} + +PACKAGE_BEFORE_PN += "${PN}-passphrase ${PN}-cli" +PACKAGES =+ "${PN}-lib" +PACKAGES += "${PN}-plugins" +ALLOW_EMPTY:${PN}-plugins = "1" + +PACKAGES_DYNAMIC += "^${PN}-plugin-.*$" +NOAUTOPACKAGEDEBUG = "1" + +FILES:${PN}-passphrase = "${sbindir}/wpa_passphrase" +FILES:${PN}-cli = "${sbindir}/wpa_cli" +FILES:${PN}-lib = "${libdir}/libwpa_client*${SOLIBSDEV}" +FILES:${PN} += "${datadir}/dbus-1/system-services/* ${systemd_system_unitdir}/*" +FILES:${PN}-dbg += "${sbindir}/.debug ${libdir}/.debug" + +CONFFILES:${PN} += "${sysconfdir}/wpa_supplicant.conf" + +RRECOMMENDS:${PN} = "${PN}-passphrase ${PN}-cli ${PN}-plugins" + +SYSTEMD_SERVICE:${PN} = "wpa_supplicant.service" +SYSTEMD_AUTO_ENABLE = "disable" + +python split_wpa_supplicant_libs () { + libdir = d.expand('${libdir}/wpa_supplicant') + dbglibdir = os.path.join(libdir, '.debug') + + split_packages = do_split_packages(d, libdir, r'^(.*)\.so', '${PN}-plugin-%s', 'wpa_supplicant %s plugin', prepend=True) + split_dbg_packages = do_split_packages(d, dbglibdir, r'^(.*)\.so', '${PN}-plugin-%s-dbg', 'wpa_supplicant %s plugin - Debugging files', prepend=True, extra_depends='${PN}-dbg') + + if split_packages: + pn = d.getVar('PN') + d.setVar('RRECOMMENDS:' + pn + '-plugins', ' '.join(split_packages)) + d.appendVar('RRECOMMENDS:' + pn + '-dbg', ' ' + ' '.join(split_dbg_packages)) +} +PACKAGESPLITFUNCS += "split_wpa_supplicant_libs" diff --git a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.9.bb b/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.9.bb deleted file mode 100644 index 3e92427bb0..0000000000 --- a/meta/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.9.bb +++ /dev/null @@ -1,110 +0,0 @@ -SUMMARY = "Client for Wi-Fi Protected Access (WPA)" -HOMEPAGE = "http://w1.fi/wpa_supplicant/" -BUGTRACKER = "http://w1.fi/security/" -SECTION = "network" -LICENSE = "BSD-3-Clause" -LIC_FILES_CHKSUM = "file://COPYING;md5=279b4f5abb9c153c285221855ddb78cc \ - file://README;beginline=1;endline=56;md5=e7d3dbb01f75f0b9799e192731d1e1ff \ - file://wpa_supplicant/wpa_supplicant.c;beginline=1;endline=12;md5=0a8b56d3543498b742b9c0e94cc2d18b" -DEPENDS = "dbus libnl" -RRECOMMENDS_${PN} = "wpa-supplicant-passphrase wpa-supplicant-cli" - -PACKAGECONFIG ??= "gnutls" -PACKAGECONFIG[gnutls] = ",,gnutls libgcrypt" -PACKAGECONFIG[openssl] = ",,openssl" - -inherit pkgconfig systemd - -SYSTEMD_SERVICE_${PN} = "wpa_supplicant.service wpa_supplicant-nl80211@.service wpa_supplicant-wired@.service" -SYSTEMD_AUTO_ENABLE = "disable" - -SRC_URI = "http://w1.fi/releases/wpa_supplicant-${PV}.tar.gz \ - file://defconfig \ - file://wpa-supplicant.sh \ - file://wpa_supplicant.conf \ - file://wpa_supplicant.conf-sane \ - file://99_wpa_supplicant \ - file://0001-replace-systemd-install-Alias-with-WantedBy.patch \ - file://0001-AP-Silently-ignore-management-frame-from-unexpected-.patch \ - " -SRC_URI[md5sum] = "2d2958c782576dc9901092fbfecb4190" -SRC_URI[sha256sum] = "fcbdee7b4a64bea8177973299c8c824419c413ec2e3a95db63dd6a5dc3541f17" - -CVE_PRODUCT = "wpa_supplicant" - -S = "${WORKDIR}/wpa_supplicant-${PV}" - -PACKAGES_prepend = "wpa-supplicant-passphrase wpa-supplicant-cli " -FILES_wpa-supplicant-passphrase = "${bindir}/wpa_passphrase" -FILES_wpa-supplicant-cli = "${sbindir}/wpa_cli" -FILES_${PN} += "${datadir}/dbus-1/system-services/*" -CONFFILES_${PN} += "${sysconfdir}/wpa_supplicant.conf" - -do_configure () { - ${MAKE} -C wpa_supplicant clean - install -m 0755 ${WORKDIR}/defconfig wpa_supplicant/.config - - if echo "${PACKAGECONFIG}" | grep -qw "openssl"; then - ssl=openssl - elif echo "${PACKAGECONFIG}" | grep -qw "gnutls"; then - ssl=gnutls - fi - if [ -n "$ssl" ]; then - sed -i "s/%ssl%/$ssl/" wpa_supplicant/.config - fi - - # For rebuild - rm -f wpa_supplicant/*.d wpa_supplicant/dbus/*.d -} - -export EXTRA_CFLAGS = "${CFLAGS}" -export BINDIR = "${sbindir}" - -do_compile () { - unset CFLAGS CPPFLAGS CXXFLAGS - sed -e "s:CFLAGS\ =.*:& \$(EXTRA_CFLAGS):g" -i ${S}/src/lib.rules - oe_runmake -C wpa_supplicant -} - -do_install () { - install -d ${D}${sbindir} - install -m 755 wpa_supplicant/wpa_supplicant ${D}${sbindir} - install -m 755 wpa_supplicant/wpa_cli ${D}${sbindir} - - install -d ${D}${bindir} - install -m 755 wpa_supplicant/wpa_passphrase ${D}${bindir} - - install -d ${D}${docdir}/wpa_supplicant - install -m 644 wpa_supplicant/README ${WORKDIR}/wpa_supplicant.conf ${D}${docdir}/wpa_supplicant - - install -d ${D}${sysconfdir} - install -m 600 ${WORKDIR}/wpa_supplicant.conf-sane ${D}${sysconfdir}/wpa_supplicant.conf - - install -d ${D}${sysconfdir}/network/if-pre-up.d/ - install -d ${D}${sysconfdir}/network/if-post-down.d/ - install -d ${D}${sysconfdir}/network/if-down.d/ - install -m 755 ${WORKDIR}/wpa-supplicant.sh ${D}${sysconfdir}/network/if-pre-up.d/wpa-supplicant - cd ${D}${sysconfdir}/network/ && \ - ln -sf ../if-pre-up.d/wpa-supplicant if-post-down.d/wpa-supplicant - - install -d ${D}/${sysconfdir}/dbus-1/system.d - install -m 644 ${S}/wpa_supplicant/dbus/dbus-wpa_supplicant.conf ${D}/${sysconfdir}/dbus-1/system.d - install -d ${D}/${datadir}/dbus-1/system-services - install -m 644 ${S}/wpa_supplicant/dbus/*.service ${D}/${datadir}/dbus-1/system-services - - if ${@bb.utils.contains('DISTRO_FEATURES','systemd','true','false',d)}; then - install -d ${D}/${systemd_unitdir}/system - install -m 644 ${S}/wpa_supplicant/systemd/*.service ${D}/${systemd_unitdir}/system - fi - - install -d ${D}/etc/default/volatiles - install -m 0644 ${WORKDIR}/99_wpa_supplicant ${D}/etc/default/volatiles -} - -pkg_postinst_wpa-supplicant () { - # If we're offline, we don't need to do this. - if [ "x$D" = "x" ]; then - killall -q -HUP dbus-daemon || true - fi - -} |