| Age | Commit message (Collapse) | Author |
|---|
|
The Hyper-V Linux Integration Services use the VMBus implementation for
communication with the Hypervisor. VMBus registers its own interrupt
handler that completely bypasses the common Linux interrupt handling.
This implies that the interrupt entropy collector is not triggered.
This patch adds the interrupt entropy collection callback into the VMBus
interrupt handler function.
Cc: stable@kernel.org
Signed-off-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Kdump keeps biting. Turns out CHANNELMSG_UNLOAD_RESPONSE is always
delivered to the CPU which was used for initial contact or to CPU0
depending on host version. vmbus_wait_for_unload() doesn't account for
the fact that in case we're crashing on some other CPU we won't get the
CHANNELMSG_UNLOAD_RESPONSE message and our wait on the current CPU will
never end.
Do the following:
1) Check for completion_done() in the loop. In case interrupt handler is
still alive we'll get the confirmation we need.
2) Read message pages for all CPUs message page as we're unsure where
CHANNELMSG_UNLOAD_RESPONSE is going to be delivered to. We can race with
still-alive interrupt handler doing the same, add cmpxchg() to
vmbus_signal_eom() to not lose CHANNELMSG_UNLOAD_RESPONSE message.
3) Cleanup message pages on all CPUs. This is required (at least for the
current CPU as we're clearing CPU0 messages now but we may want to bring
up additional CPUs on crash) as new messages won't be delivered till we
consume what's pending. On boot we'll place message pages somewhere else
and we won't be able to read stale messages.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify the logic that picks MMIO ranges by pulling out the
logic related to trying to lay frame buffer claim on top of where
the firmware placed the frame buffer.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Later in the boot sequence, we need to figure out which memory
ranges can be given out to various paravirtual drivers. The
hyperv_fb driver should, ideally, be placed right on top of
the frame buffer, without some other device getting plopped on
top of this range in the meantime. Recording this now allows
that to be guaranteed.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch changes vmbus_allocate_mmio() and vmbus_free_mmio() so
that when child paravirtual devices allocate memory-mapped I/O
space, they allocate it privately from a resource tree pointed
at by hyperv_mmio and also by the public resource tree
iomem_resource. This allows the region to be marked as "busy"
in the private tree, but a "bridge window" in the public tree,
guaranteeing that no two bridge windows will overlap each other
but while also allowing the PCI device children of the bridge
windows to overlap that window.
One might conclude that this belongs in the pnp layer, rather
than in this driver. Rafael Wysocki, the maintainter of the
pnp layer, has previously asked that we not modify the pnp layer
as it is considered deprecated. This patch is thus essentially
a workaround.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A patch later in this series allocates child nodes
in this resource tree. For that to work, this tree
needs to be sorted in ascending order.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces a function that reverses everything
done by vmbus_allocate_mmio(). Existing code just called
release_mem_region(). Future patches in this series
require a more complex sequence of actions, so this function
is introduced to wrap those actions.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In existing code, this tree of resources is created
in single-threaded code and never modified after it is
created, and thus needs no locking. This patch introduces
a semaphore for tree access, as other patches in this
series introduce run-time modifications of this resource
tree which can happen on multiple threads.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Starting with Windows 2012 R2, message inteerupts can be delivered
on any VCPU in the guest. Support this functionality.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have 3 functions dealing with messages and they all implement
the same logic to finalize reads, move it to vmbus_signal_eom().
Suggested-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Radim Kr.má<rkrcmar@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
wait_for_completion() may sleep, it enables interrupts and this
is something we really want to avoid on crashes because interrupt
handlers can cause other crashes. Switch to the recently introduced
vmbus_wait_for_unload() doing busy wait instead.
Reported-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Radim Kr.má<rkrcmar@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We must handle HVMSG_TIMER_EXPIRED messages in the interrupt context
and we offload all the rest to vmbus_on_msg_dpc() tasklet. This functions
loops to see if there are new messages pending. In case we'll ever see
HVMSG_TIMER_EXPIRED message there we're going to lose it as we can't
handle it from there. Avoid looping in vmbus_on_msg_dpc(), we're OK
with handling one message per interrupt.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Radim Kr.má<rkrcmar@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Only the coming hv_sock driver has a "true" value for this flag.
We treat the hvsock offers/channels as special VMBus devices.
Since the hv_sock driver handles all the hvsock offers/channels, we need to
tweak vmbus_match() for hv_sock driver, so we introduce this flag.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add vendor and device attributes to VMBUS devices. These will be used
by Hyper-V tools as well user-level RDMA libraries that will use the
vendor/device tuple to discover the RDMA device.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes 16GB GPUs work in Hyper-V VMs, since, for
compatibility reasons, the Hyper-V BIOS lists MMIO ranges in 2GB
chunks in its root bus's _CRS object.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the path vmbus_onoffer_rescind() -> vmbus_device_unregister() ->
device_unregister() -> ... -> __device_release_driver(), we can see for a
device without a driver loaded: dev->driver is NULL, so
dev->bus->remove(dev), namely vmbus_remove(), isn't invoked.
As a result, vmbus_remove() -> hv_process_channel_removal() isn't invoked
and some cleanups(like sending a CHANNELMSG_RELID_RELEASED message to the
host) aren't done.
We can demo the issue this way:
1. rmmod hv_utils;
2. disable the Heartbeat Integration Service in Hyper-V Manager and lsvmbus
shows the device disappears.
3. re-enable the Heartbeat in Hyper-V Manager and modprobe hv_utils, but
lsvmbus shows the device can't appear again.
This is because, the host thinks the VM hasn't released the relid, so can't
re-offer the device to the VM.
We can fix the issue by moving hv_process_channel_removal()
from vmbus_close_internal() to vmbus_device_release(), since the latter is
always invoked on device_unregister(), whether or not the dev has a driver
loaded.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The irq we extract from ACPI is not used - we deliver hypervisor
interrupts on a special vector. Make the necessary adjustments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use uuid_le_cmp() for comparing GUIDs.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Consistently use uuid_le type in the Hyper-V driver code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch exposes the mapping between Linux CPU number and Hyper-V virtual
processor number. This is necessary because the hypervisor needs to know which
virtual processors to target when making a mapping in the Interrupt Redirection
Table in the I/O MMU.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before vmbus_connect() synic is setup per vcpu - this means
hypervisor receives writes at synic msr's and probably allocate
hypervisor resources per synic setup.
If vmbus_connect() failed for some reason it's neccessary to cleanup
synic setup by call hv_synic_cleanup() at each vcpu to get a chance
to free allocated resources by hypervisor per synic.
This patch does appropriate cleanup in case of vmbus_connect() failure.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e513229b4c38 ("Drivers: hv: vmbus: prevent cpu offlining on newer
hypervisors") was altering smp_ops.cpu_disable to prevent CPU offlining.
We can bo better by using cpu_hotplug_enable/disable functions instead of
such hard-coding.
Reported-by: Radim Kr.má <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is useful to analyze performance issue.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch deletes the logic from hyperv_fb which picked a range of MMIO space
for the frame buffer and adds new logic to hv_vmbus which picks ranges for
child drivers. The new logic isn't quite the same as the old, as it considers
more possible ranges.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch changes the logic in hv_vmbus to record all of the ranges in the
VM's firmware (BIOS or UEFI) that offer regions of memory-mapped I/O space for
use by paravirtual front-end drivers. The old logic just found one range
above 4GB and called it good. This logic will find any ranges above 1MB.
It would have been possible with this patch to just use existing resource
allocation functions, rather than keep track of the entire set of Hyper-V
related MMIO regions in VMBus. This strategy, however, is not sufficient
when the resource allocator needs to be aware of the constraints of a
Hyper-V virtual machine, which is what happens in the next patch in the series.
So this first patch exists to show the first steps in reworking the MMIO
allocation paths for Hyper-V front-end drivers.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hypervisor Top Level Functional Specification v3.1/4.0 notes that cpuid
(0x40000003) EDX's 10th bit should be used to check that Hyper-V guest
crash MSR's functionality available.
This patch should fix this recognition. Currently the code checks EAX
register instead of EDX.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
current_pt_regs() sometimes returns regs of the userspace process and in
case of a kernel crash this is not what we need to report. E.g. when we
trigger crash with sysrq we see the following:
...
RIP: 0010:[<ffffffff815b8696>] [<ffffffff815b8696>] sysrq_handle_crash+0x16/0x20
RSP: 0018:ffff8800db0a7d88 EFLAGS: 00010246
RAX: 000000000000000f RBX: ffffffff820a0660 RCX: 0000000000000000
...
at the same time current_pt_regs() give us:
ip=7f899ea7e9e0, ax=ffffffffffffffda, bx=26c81a0, cx=7f899ea7e9e0, ...
These registers come from the userspace process triggered the crash. As we
don't even know which process it was this information is rather useless.
When kernel crash happens through 'die' proper regs are being passed to
all receivers on the die_chain (and panic_notifier_list is being notified
with the string passed to panic() only). If panic() is called manually
(e.g. on BUG()) we won't get 'die' notification so keep the 'panic'
notification reporter as well but guard against double reporting.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Full kernel hang is observed when kdump kernel starts after a crash. This
hang happens in vmbus_negotiate_version() function on
wait_for_completion() as Hyper-V host (Win2012R2 in my testing) never
responds to CHANNELMSG_INITIATE_CONTACT as it thinks the connection is
already established. We need to perform some mandatory minimalistic
cleanup before we start new kernel.
Reported-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When general-purpose kexec (not kdump) is being performed in Hyper-V guest
the newly booted kernel fails with an MCE error coming from the host. It
is the same error which was fixed in the "Drivers: hv: vmbus: Implement
the protocol for tearing down vmbus state" commit - monitor pages remain
special and when they're being written to (as the new kernel doesn't know
these pages are special) bad things happen. We need to perform some
minimalistic cleanup before booting a new kernel on kexec. To do so we
need to register a special machine_ops.shutdown handler to be executed
before the native_machine_shutdown(). Registering a shutdown notification
handler via the register_reboot_notifier() call is not sufficient as it
happens to early for our purposes. machine_ops is not being exported to
modules (and I don't think we want to export it) so let's do this in
mshyperv.c
The minimalistic cleanup consists of cleaning up clockevents, synic MSRs,
guest os id MSR, and hypercall MSR.
Kdump doesn't require all this stuff as it lives in a separate memory
space.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We already have hv_synic_free() which frees all per-cpu pages for all
CPUs, let's remove the hv_synic_free_cpu() call from hv_synic_cleanup()
so it will be possible to do separate cleanup (writing to MSRs) and final
freeing. This is going to be used to assist kexec.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Explicitly kill tasklets we create on module unload.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement the protocol for tearing down the monitor state established with
the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 96c1d0581d00f7abe033350edb021a9d947d8d81 ("Drivers: hv: vmbus: Add
support for VMBus panic notifier handler") introduced
atomic_notifier_chain_register() call on module load. We also need to call
atomic_notifier_chain_unregister() on module unload as otherwise the following
crash is observed when we bring hv_vmbus back:
[ 39.788877] BUG: unable to handle kernel paging request at ffffffffa00078a8
[ 39.788877] IP: [<ffffffff8109d63f>] notifier_call_chain+0x3f/0x80
...
[ 39.788877] Call Trace:
[ 39.788877] [<ffffffff8109de7d>] __atomic_notifier_call_chain+0x5d/0x90
...
[ 39.788877] [<ffffffff8109d788>] ? atomic_notifier_chain_register+0x38/0x70
[ 39.788877] [<ffffffff8109d767>] ? atomic_notifier_chain_register+0x17/0x70
[ 39.788877] [<ffffffffa002814f>] hv_acpi_init+0x14f/0x1000 [hv_vmbus]
[ 39.788877] [<ffffffff81002144>] do_one_initcall+0xd4/0x210
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case we do request_resource() in vmbus_acpi_add() we need to tear it down
to be able to load the driver again. Otherwise the following crash in observed
when hv_vmbus unload/load sequence is performed on a Generation2 instance:
[ 38.165701] BUG: unable to handle kernel paging request at ffffffffa00075a0
[ 38.166315] IP: [<ffffffff8107dc5f>] __request_resource+0x2f/0x50
[ 38.166315] PGD 1f34067 PUD 1f35063 PMD 3f723067 PTE 0
[ 38.166315] Oops: 0000 [#1] SMP
[ 38.166315] Modules linked in: hv_vmbus(+) [last unloaded: hv_vmbus]
[ 38.166315] CPU: 0 PID: 267 Comm: modprobe Not tainted 3.19.0-rc5_bug923184+ #486
[ 38.166315] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012
[ 38.166315] task: ffff88003f401cb0 ti: ffff88003f60c000 task.ti: ffff88003f60c000
[ 38.166315] RIP: 0010:[<ffffffff8107dc5f>] [<ffffffff8107dc5f>] __request_resource+0x2f/0x50
[ 38.166315] RSP: 0018:ffff88003f60fb58 EFLAGS: 00010286
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A work item in vmbus_connection.work_queue can sleep, waiting for a new
host message (usually it is some kind of "completion" message). Currently
the new message will be handled in the same workqueue, but since work items
in the workqueue is serialized, we actually have no chance to handle
the new message if the current work item is sleeping -- as as result, the
current work item will hang forever.
K. Y. has posted the below fix to resolve the issue:
Drivers: hv: vmbus: Perform device register in the per-channel work element
Actually we can simplify the fix by directly running non-blocking message
handlers in the dispatch tasklet (inspired by K. Y.).
This patch is the fundamental change. The following 2 patches will simplify
the message offering and rescind-offering handling a lot.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hyper-V allows a guest to notify the Hyper-V host that a panic
condition occured. This notification can include up to five 64
bit values. These 64 bit values are written into crash MSRs.
Once the data has been written into the crash MSRs, the host is
then notified by writing into a Crash Control MSR. On the Hyper-V
host, the panic notification data is captured in the Windows Event
log as a 18590 event.
Crash MSRs are defined in appendix H of the Hypervisor Top Level
Functional Specification. At the time of this patch, v4.0 is the
current functional spec. The URL for the v4.0 document is:
http://download.microsoft.com/download/A/B/4/AB43A34E-BDD0-4FA6-BDEF-79EEF16E880B/Hypervisor Top Level Functional Specification v4.0.docx
Signed-off-by: Nick Meier <nmeier@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In response to a rescind message, we need to remove the channel and the
corresponding device. Cleanup this code path by factoring out the code
to remove a channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handle the case when the device may be removed when the device has no driver
attached to it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Newly introduced clockevent devices made it impossible to unload hv_vmbus
module as clockevents_config_and_register() takes additional reverence to
the module. To make it possible again we do the following:
- avoid setting dev->owner for clockevent devices;
- implement hv_synic_clockevents_cleanup() doing clockevents_unbind_device();
- call it from vmbus_exit().
In theory hv_synic_clockevents_cleanup() can be merged with hv_synic_cleanup(),
however, we call hv_synic_cleanup() from smp_call_function_single() and this
doesn't work for clockevents_unbind_device() as it does such call on its own. I
opted for a separate function.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SynIC has to be switched off when we unload the module, otherwise registered
memory pages can get corrupted after (as Hyper-V host still writes there) and
we see the following crashes for random processes:
[ 89.116774] BUG: Bad page map in process sh pte:4989c716 pmd:36f81067
[ 89.159454] addr:0000000000437000 vm_flags:00000875 anon_vma: (null) mapping:ffff88007bba55a0 index:37
[ 89.226146] vma->vm_ops->fault: filemap_fault+0x0/0x410
[ 89.257776] vma->vm_file->f_op->mmap: generic_file_mmap+0x0/0x60
[ 89.297570] CPU: 0 PID: 215 Comm: sh Tainted: G B 3.19.0-rc5_bug923184+ #488
[ 89.353738] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090006 05/23/2012
[ 89.409138] 0000000000000000 000000004e083d7b ffff880036e9fa18 ffffffff81a68d31
[ 89.468724] 0000000000000000 0000000000437000 ffff880036e9fa68 ffffffff811a1e3a
[ 89.519233] 000000004989c716 0000000000000037 ffffea0001edc340 0000000000437000
[ 89.575751] Call Trace:
[ 89.591060] [<ffffffff81a68d31>] dump_stack+0x45/0x57
[ 89.625164] [<ffffffff811a1e3a>] print_bad_pte+0x1aa/0x250
[ 89.667234] [<ffffffff811a2c95>] vm_normal_page+0x55/0xa0
[ 89.703818] [<ffffffff811a3105>] unmap_page_range+0x425/0x8a0
[ 89.737982] [<ffffffff811a3601>] unmap_single_vma+0x81/0xf0
[ 89.780385] [<ffffffff81184320>] ? lru_deactivate_fn+0x190/0x190
[ 89.820130] [<ffffffff811a4131>] unmap_vmas+0x51/0xa0
[ 89.860168] [<ffffffff811ad12c>] exit_mmap+0xac/0x1a0
[ 89.890588] [<ffffffff810763c3>] mmput+0x63/0x100
[ 89.919205] [<ffffffff811eba48>] flush_old_exec+0x3f8/0x8b0
[ 89.962135] [<ffffffff8123b5bb>] load_elf_binary+0x32b/0x1260
[ 89.998581] [<ffffffff811a14f2>] ? get_user_pages+0x52/0x60
hv_synic_cleanup() function exists but noone calls it now. Do the following:
- call hv_synic_cleanup() on each cpu from vmbus_exit();
- write global disable bit through MSR;
- use hv_synic_free_cpu() to avoid memory leask and code duplication.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pages on shutdown
We need to destroy hv_vmbus_con on module shutdown, otherwise the following
crash is sometimes observed:
[ 76.569845] hv_vmbus: Hyper-V Host Build:9600-6.3-17-0.17039; Vmbus version:3.0
[ 82.598859] BUG: unable to handle kernel paging request at ffffffffa0003480
[ 82.599287] IP: [<ffffffffa0003480>] 0xffffffffa0003480
[ 82.599287] PGD 1f34067 PUD 1f35063 PMD 3f72d067 PTE 0
[ 82.599287] Oops: 0010 [#1] SMP
[ 82.599287] Modules linked in: [last unloaded: hv_vmbus]
[ 82.599287] CPU: 0 PID: 26 Comm: kworker/0:1 Not tainted 3.19.0-rc5_bug923184+ #488
[ 82.599287] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012
[ 82.599287] Workqueue: hv_vmbus_con 0xffffffffa0003480
[ 82.599287] task: ffff88007b6ddfa0 ti: ffff88007f8f8000 task.ti: ffff88007f8f8000
[ 82.599287] RIP: 0010:[<ffffffffa0003480>] [<ffffffffa0003480>] 0xffffffffa0003480
[ 82.599287] RSP: 0018:ffff88007f8fbe00 EFLAGS: 00010202
...
To avoid memory leaks we need to free monitor_pages and int_page for
vmbus_connection. Implement vmbus_disconnect() function by separating cleanup
path from vmbus_connect().
As we use hv_vmbus_con to release channels (see free_channel() in channel_mgmt.c)
we need to make sure the work was done before we remove the queue, do that with
drain_workqueue(). We also need to avoid handling messages which can (potentially)
create new channels, so set vmbus_connection.conn_state = DISCONNECTED at the very
beginning of vmbus_exit() and check for that in vmbus_onmessage_work().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All channel work queues are named 'hv_vmbus_ctl', this makes them
indistinguishable in ps output and makes it hard to link to the corresponding
vmbus device. Rename them to hv_vmbus_ctl/N and make vmbus device names match,
e.g. now vmbus_1 device is served by hv_vmbus_ctl/1 work queue.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When an SMP Hyper-V guest is running on top of 2012R2 Server and secondary
cpus are sent offline (with echo 0 > /sys/devices/system/cpu/cpu$cpu/online)
the system freeze is observed. This happens due to the fact that on newer
hypervisors (Win8, WS2012R2, ...) vmbus channel handlers are distributed
across all cpus (see init_vp_index() function in drivers/hv/channel_mgmt.c)
and on cpu offlining nobody reassigns them to CPU0. Prevent cpu offlining
when vmbus is loaded until the issue is fixed host-side.
This patch also disables hibernation but it is OK as it is also broken (MCE
error is hit on resume). Suspend still works.
Tested with WS2008R2 and WS2012R2.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc patches from Greg KH:
"Here's the big char/misc driver update for 3.20-rc1.
Lots of little things in here, all described in the changelog.
Nothing major or unusual, except maybe the binder selinux stuff, which
was all acked by the proper selinux people and they thought it best to
come through this tree.
All of this has been in linux-next with no reported issues for a while"
* tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
coresight: fix function etm_writel_cp14() parameter order
coresight-etm: remove check for unknown Kconfig macro
coresight: fixing CPU hwid lookup in device tree
coresight: remove the unnecessary function coresight_is_bit_set()
coresight: fix the debug AMBA bus name
coresight: remove the extra spaces
coresight: fix the link between orphan connection and newly added device
coresight: remove the unnecessary replicator property
coresight: fix the replicator subtype value
pdfdocs: Fix 'make pdfdocs' failure for 'uio-howto.tmpl'
mcb: Fix error path of mcb_pci_probe
virtio/console: verify device has config space
ti-st: clean up data types (fix harmless memory corruption)
mei: me: release hw from reset only during the reset flow
mei: mask interrupt set bit on clean reset bit
extcon: max77693: Constify struct regmap_config
extcon: adc-jack: Release IIO channel on driver remove
extcon: Remove duplicated include from extcon-class.c
Drivers: hv: vmbus: hv_process_timer_expiration() can be static
Drivers: hv: vmbus: serialize Offer and Rescind offer
...
|
|
structures.
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
drivers/hv/vmbus_drv.c:582:6: sparse: symbol 'hv_process_timer_expiration' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement a clockevent device based on the timer support available on
Hyper-V.
In this version of the patch I have addressed Jason's review comments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The uuid structure could be managed as a const in several places.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
|
Stephan Mueller
Vitaly Kuznetsov
Jake Oshins
K. Y. Srinivasan
Dexuan Cui
Andrey Smetanin
Denis V. Lunev
kbuild test robot
Nick Meier
Linus Torvalds
Lv Zheng
stephen hemminger