diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa')
4 files changed, 184 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 1811e1972a7a..5201bc15fdd6 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -46,6 +46,42 @@ Required properties: "brcm,bcm6328-switch" "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" +Required properties for BCM585xx/586xx/88312 SoCs: + + - reg: a total of 3 register base addresses, the first one must be the + Switch Register Access block base, the second is the port 5/4 mux + configuration register and the third one is the SGMII configuration + and status register base address. + + - interrupts: a total of 13 interrupts must be specified, in the following + order: port 0-5, 7-8 link status change, then the integrated PHY interrupt, + then the timestamping interrupt and the sleep timer interrupts for ports + 5,7,8. + +Optional properties for BCM585xx/586xx/88312 SoCs: + + - reg-names: a total of 3 names matching the 3 base register address, must + be in the following order: + "srab" + "mux_config" + "sgmii_config" + + - interrupt-names: a total of 13 names matching the 13 interrupts specified + must be in the following order: + "link_state_p0" + "link_state_p1" + "link_state_p2" + "link_state_p3" + "link_state_p4" + "link_state_p5" + "link_state_p7" + "link_state_p8" + "phy" + "ts" + "imp_sleep_timer_p5" + "imp_sleep_timer_p7" + "imp_sleep_timer_p8" + See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 3ceeb8de1196..35694c0c376b 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -7,7 +7,7 @@ limitations. Current Binding --------------- -Switches are true Linux devices and can be probes by any means. Once +Switches are true Linux devices and can be probed by any means. Once probed, they register to the DSA framework, passing a node pointer. This node is expected to fulfil the following binding, and may contain additional properties as required by the device it is diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index ac145b885e95..0f407fb371ce 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -8,6 +8,10 @@ Required properties: - "microchip,ksz9477" - "microchip,ksz9897" +Optional properties: + +- reset-gpios : Should be a gpio specifier for a reset line + See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt new file mode 100644 index 000000000000..886cbe8ffb38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -0,0 +1,143 @@ +Lantiq GSWIP Ethernet switches +================================== + +Required properties for GSWIP core: + +- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the + xRX200 SoC +- reg : memory range of the GSWIP core registers + : memory range of the GSWIP MDIO registers + : memory range of the GSWIP MII registers + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of +additional required and optional properties. + + +Required properties for MDIO bus: +- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP + core of the xRX200 SoC and the PHYs connected to it. + +See Documentation/devicetree/bindings/net/mdio.txt for a list of additional +required and optional properties. + + +Required properties for GPHY firmware loading: +- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw" + for the loading of the firmware into the embedded + GPHY core of the SoC. +- lantiq,rcu : reference to the rcu syscon + +The GPHY firmware loader has a list of GPHY entries, one for each +embedded GPHY + +- reg : Offset of the GPHY firmware register in the RCU + register range +- resets : list of resets of the embedded GPHY +- reset-names : list of names of the resets + +Example: + +Ethernet switch on the VRX200 SoC: + +switch@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-gswip"; + reg = < 0xe108000 0x3100 /* switch */ + 0xe10b100 0xd8 /* mdio */ + 0xe10b1d8 0x130 /* mii */ + >; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + + port@4 { + reg = <4>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy13>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + + port@6 { + reg = <0x6>; + label = "cpu"; + ethernet = <ð0>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + }; + }; + + gphy-fw { + compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"; + lantiq,rcu = <&rcu0>; + #address-cells = <1>; + #size-cells = <0>; + + gphy@20 { + reg = <0x20>; + + resets = <&reset0 31 30>; + reset-names = "gphy"; + }; + + gphy@68 { + reg = <0x68>; + + resets = <&reset0 29 28>; + reset-names = "gphy"; + }; + }; +}; |