diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
22 files changed, 480 insertions, 75 deletions
diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index 4648948f7c3b..e15589f47787 100644 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -19,6 +19,9 @@ Optional properties: - interrupt-names: must be "mdio_done_error" when there is a share interrupt fed to this hardware block, or must be "mdio_done" for the first interrupt and "mdio_error" for the second when there are separate interrupts +- clocks: A reference to the clock supplying the MDIO bus controller +- clock-frequency: the MDIO bus clock that must be output by the MDIO bus + hardware, if absent, the default hardware values are used Child nodes of this MDIO bus controller node are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt index 4194ff7e6ee6..c26f4e11037c 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -10,6 +10,8 @@ device the slave device is attached to. Required properties: - compatible: should contain one of the following: + * "brcm,bcm20702a1" + * "brcm,bcm4330-bt" * "brcm,bcm43438-bt" Optional properties: @@ -18,8 +20,13 @@ Optional properties: - shutdown-gpios: GPIO specifier, used to enable the BT module - device-wakeup-gpios: GPIO specifier, used to wakeup the controller - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor - - clocks: clock specifier if external clock provided to the controller - - clock-names: should be "extclk" + - clocks: 1 or 2 clocks as defined in clock-names below, in that order + - clock-names: names for clock inputs, matching the clocks given + - "extclk": deprecated, replaced by "txco" + - "txco": external reference clock (not a standalone crystal) + - "lpo": external low power 32.768 kHz clock + - vbat-supply: phandle to regulator supply for VBAT + - vddio-supply: phandle to regulator supply for VDDIO Example: diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index bfc0c433654f..bc77477c6878 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -24,6 +24,14 @@ Optional properties: if this property is present then controller is assumed to be big endian. +- fsl,stop-mode: register bits of stop mode control, the format is + <&gpr req_gpr req_bit ack_gpr ack_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset of CAN stop request. + req_bit is the bit offset of CAN stop request. + ack_gpr is the gpr register offset of CAN stop acknowledge. + ack_bit is the bit offset of CAN stop acknowledge. + Example: can@1c000 { diff --git a/Documentation/devicetree/bindings/net/can/holt_hi311x.txt b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt index 903a78da65be..3a9926f99937 100644 --- a/Documentation/devicetree/bindings/net/can/holt_hi311x.txt +++ b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt @@ -17,7 +17,7 @@ Example: reg = <1>; clocks = <&clk32m>; interrupt-parent = <&gpio4>; - interrupts = <13 IRQ_TYPE_EDGE_RISING>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; vdd-supply = <®5v0>; xceiver-supply = <®5v0>; }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 94a7f33ac5e9..9936b9ee67c3 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -3,7 +3,9 @@ Renesas R-Car CAN controller Device Tree Bindings Required properties: - compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC. + "renesas,can-r8a7744" if CAN controller is a part of R8A7744 SoC. "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC. + "renesas,can-r8a774a1" if CAN controller is a part of R8A774A1 SoC. "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. @@ -13,26 +15,32 @@ Required properties: "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC. "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. "renesas,can-r8a7796" if CAN controller is a part of R8A7796 SoC. + "renesas,can-r8a77965" if CAN controller is a part of R8A77965 SoC. "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-can" for a generic R-Car Gen2 or RZ/G1 compatible device. - "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device. + "renesas,rcar-gen3-can" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first followed by the generic version. - reg: physical base address and size of the R-Car CAN register map. - interrupts: interrupt specifier for the sole interrupt. -- clocks: phandles and clock specifiers for 3 CAN clock inputs. -- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk". +- clocks: phandles and clock specifiers for 2 CAN clock inputs for RZ/G2 + devices. + phandles and clock specifiers for 3 CAN clock inputs for every other + SoC. +- clock-names: 2 clock input name strings for RZ/G2: "clkp1", "can_clk". + 3 clock input name strings for every other SoC: "clkp1", "clkp2", + "can_clk". - pinctrl-0: pin control group to be used for this controller. - pinctrl-names: must be "default". -Required properties for "renesas,can-r8a7795" and "renesas,can-r8a7796" -compatible: -In R8A7795 and R8A7796 SoCs, "clkp2" can be CANFD clock. This is a div6 clock -and can be used by both CAN and CAN FD controller at the same time. It needs to -be scaled to maximum frequency if any of these controllers use it. This is done +Required properties for R8A7795, R8A7796 and R8A77965: +For the denoted SoCs, "clkp2" can be CANFD clock. This is a div6 clock and can +be used by both CAN and CAN FD controller at the same time. It needs to be +scaled to maximum frequency if any of these controllers use it. This is done using the below properties: - assigned-clocks: phandle of clkp2(CANFD) clock. @@ -41,8 +49,9 @@ using the below properties: Optional properties: - renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: <0x0> (default) : Peripheral clock (clkp1) - <0x1> : Peripheral clock (clkp2) - <0x3> : Externally input clock + <0x1> : Peripheral clock (clkp2) (not supported by + RZ/G2 devices) + <0x3> : External input clock Example ------- diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt index 060e2d46bad9..100cc40b8510 100644 --- a/Documentation/devicetree/bindings/net/can/xilinx_can.txt +++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt @@ -6,6 +6,7 @@ Required properties: - "xlnx,zynq-can-1.0" for Zynq CAN controllers - "xlnx,axi-can-1.00.a" for Axi CAN controllers - "xlnx,canfd-1.0" for CAN FD controllers + - "xlnx,canfd-2.0" for CAN FD 2.0 controllers - reg : Physical base address and size of the controller registers map. - interrupts : Property with a value describing the interrupt diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index b3acebe08eb0..3264e1978d25 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -22,7 +22,8 @@ Required properties: - cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection device. See also cpsw-phy-sel.txt for it's binding. Note that in legacy cases cpsw-phy-sel may be - a child device instead of a phandle. + a child device instead of a phandle + (DEPRECATED, use phys property instead). Optional properties: - ti,hwmods : Must be "cpgmac0" @@ -44,6 +45,7 @@ Optional properties: Slave Properties: Required properties: - phy-mode : See ethernet.txt file in the same directory +- phys : phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt) Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports @@ -85,12 +87,14 @@ Examples: phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1 0>; }; cpsw_emac1: slave@1 { phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2 0>; }; }; @@ -114,11 +118,13 @@ Examples: phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1 0>; }; cpsw_emac1: slave@1 { phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2 0>; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 1811e1972a7a..5201bc15fdd6 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -46,6 +46,42 @@ Required properties: "brcm,bcm6328-switch" "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" +Required properties for BCM585xx/586xx/88312 SoCs: + + - reg: a total of 3 register base addresses, the first one must be the + Switch Register Access block base, the second is the port 5/4 mux + configuration register and the third one is the SGMII configuration + and status register base address. + + - interrupts: a total of 13 interrupts must be specified, in the following + order: port 0-5, 7-8 link status change, then the integrated PHY interrupt, + then the timestamping interrupt and the sleep timer interrupts for ports + 5,7,8. + +Optional properties for BCM585xx/586xx/88312 SoCs: + + - reg-names: a total of 3 names matching the 3 base register address, must + be in the following order: + "srab" + "mux_config" + "sgmii_config" + + - interrupt-names: a total of 13 names matching the 13 interrupts specified + must be in the following order: + "link_state_p0" + "link_state_p1" + "link_state_p2" + "link_state_p3" + "link_state_p4" + "link_state_p5" + "link_state_p7" + "link_state_p8" + "phy" + "ts" + "imp_sleep_timer_p5" + "imp_sleep_timer_p7" + "imp_sleep_timer_p8" + See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 3ceeb8de1196..35694c0c376b 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -7,7 +7,7 @@ limitations. Current Binding --------------- -Switches are true Linux devices and can be probes by any means. Once +Switches are true Linux devices and can be probed by any means. Once probed, they register to the DSA framework, passing a node pointer. This node is expected to fulfil the following binding, and may contain additional properties as required by the device it is diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index ac145b885e95..0f407fb371ce 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -8,6 +8,10 @@ Required properties: - "microchip,ksz9477" - "microchip,ksz9897" +Optional properties: + +- reset-gpios : Should be a gpio specifier for a reset line + See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt new file mode 100644 index 000000000000..886cbe8ffb38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -0,0 +1,143 @@ +Lantiq GSWIP Ethernet switches +================================== + +Required properties for GSWIP core: + +- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the + xRX200 SoC +- reg : memory range of the GSWIP core registers + : memory range of the GSWIP MDIO registers + : memory range of the GSWIP MII registers + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of +additional required and optional properties. + + +Required properties for MDIO bus: +- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP + core of the xRX200 SoC and the PHYs connected to it. + +See Documentation/devicetree/bindings/net/mdio.txt for a list of additional +required and optional properties. + + +Required properties for GPHY firmware loading: +- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw" + for the loading of the firmware into the embedded + GPHY core of the SoC. +- lantiq,rcu : reference to the rcu syscon + +The GPHY firmware loader has a list of GPHY entries, one for each +embedded GPHY + +- reg : Offset of the GPHY firmware register in the RCU + register range +- resets : list of resets of the embedded GPHY +- reset-names : list of names of the resets + +Example: + +Ethernet switch on the VRX200 SoC: + +switch@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-gswip"; + reg = < 0xe108000 0x3100 /* switch */ + 0xe10b100 0xd8 /* mdio */ + 0xe10b1d8 0x130 /* mii */ + >; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + + port@4 { + reg = <4>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy13>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + + port@6 { + reg = <0x6>; + label = "cpu"; + ethernet = <ð0>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + }; + }; + + gphy-fw { + compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"; + lantiq,rcu = <&rcu0>; + #address-cells = <1>; + #size-cells = <0>; + + gphy@20 { + reg = <0x20>; + + resets = <&reset0 31 30>; + reset-names = "gphy"; + }; + + gphy@68 { + reg = <0x68>; + + resets = <&reset0 29 28>; + reset-names = "gphy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt index 5bb3a18cc38d..54c66d0611cb 100644 --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -10,6 +10,7 @@ Required properties: "allwinner,sun8i-r40-gmac" "allwinner,sun8i-v3s-emac" "allwinner,sun50i-a64-emac" + "allwinner,sun50i-h6-emac", "allwinner-sun50i-a64-emac" - reg: address and length of the register for the device. - interrupts: interrupt for the device - interrupt-names: must be "macirq" diff --git a/Documentation/devicetree/bindings/net/icplus-ip101ag.txt b/Documentation/devicetree/bindings/net/icplus-ip101ag.txt new file mode 100644 index 000000000000..a784592bbb15 --- /dev/null +++ b/Documentation/devicetree/bindings/net/icplus-ip101ag.txt @@ -0,0 +1,19 @@ +IC Plus Corp. IP101A / IP101G Ethernet PHYs + +There are different models of the IP101G Ethernet PHY: +- IP101GR (32-pin QFN package) +- IP101G (die only, no package) +- IP101GA (48-pin LQFP package) + +There are different models of the IP101A Ethernet PHY (which is the +predecessor of the IP101G): +- IP101A (48-pin LQFP package) +- IP101AH (48-pin LQFP package) + +Optional properties for the IP101GR (32-pin QFN package): + +- icplus,select-rx-error: + pin 21 ("RXER/INTR_32") will output the receive error status. + interrupts are not routed outside the PHY in this mode. +- icplus,select-interrupt: + pin 21 ("RXER/INTR_32") will output the interrupt signal. diff --git a/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt new file mode 100644 index 000000000000..5ff5e68bbbb6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt @@ -0,0 +1,21 @@ +Lantiq xRX200 GSWIP PMAC Ethernet driver +================================== + +Required properties: + +- compatible : "lantiq,xrx200-net" for the PMAC of the embedded + : GSWIP in the xXR200 +- reg : memory range of the PMAC core inside of the GSWIP core +- interrupts : TX and RX DMA interrupts. Use interrupt-names "tx" for + : the TX interrupt and "rx" for the RX interrupt. + +Example: + +ethernet@e10b308 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-net"; + reg = <0xe10b308 0xcf8>; + interrupts = <73>, <72>; + interrupt-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt index c329608fa887..83370ebf5b89 100644 --- a/Documentation/devicetree/bindings/net/marvell,prestera.txt +++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt @@ -2,7 +2,7 @@ Marvell Prestera Switch Chip bindings ------------------------------------- Required properties: -- compatible: one of the following +- compatible: must be "marvell,prestera" and one of the following "marvell,prestera-98dx3236", "marvell,prestera-98dx3336", "marvell,prestera-98dx4251", @@ -21,7 +21,7 @@ switch { ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>; packet-processor@0 { - compatible = "marvell,prestera-98dx3236"; + compatible = "marvell,prestera-98dx3236", "marvell,prestera"; reg = <0 0x4000000>; interrupts = <33>, <34>, <35>; dfx = <&dfx>; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index fc019df0d863..b78397669320 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -31,7 +31,7 @@ required. Required properties (port): -- interrupts: interrupt for the port +- interrupts: interrupt(s) for the port - port-id: ID of the port from the MAC point of view - gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the GOP (Group Of Ports) point of view. This ID is used to index the @@ -43,10 +43,12 @@ Optional properties (port): - marvell,loopback: port is loopback mode - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). -- interrupt-names: if more than a single interrupt for rx is given, must - be the name associated to the interrupts listed. Valid - names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3", - "rx-shared", "link". +- interrupt-names: if more than a single interrupt for is given, must be the + name associated to the interrupts listed. Valid names are: + "hifX", with X in [0..8], and "link". The names "tx-cpu0", + "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported + for backward compatibility but shouldn't be used for new + additions. - marvell,system-controller: a phandle to the system controller. Example for marvell,armada-375-pp2: @@ -89,9 +91,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <0>; gop-port-id = <0>; }; @@ -101,9 +108,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <1>; gop-port-id = <2>; }; @@ -113,9 +125,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <2>; gop-port-id = <3>; }; diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt new file mode 100644 index 000000000000..8a08621a5b54 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt @@ -0,0 +1,78 @@ +MediaTek DWMAC glue layer controller + +This file documents platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +The device node has following properties. + +Required properties: +- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC +- reg: Address and length of the register set for the device +- interrupts: Should contain the MAC interrupts +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Should be "macirq" for the main MAC IRQ +- clocks: Must contain a phandle for each entry in clock-names. +- clock-names: The name of the clock listed in the clocks property. These are + "axi", "apb", "mac_main", "ptp_ref" for MT2712 SoC +- mac-address: See ethernet.txt in the same directory +- phy-mode: See ethernet.txt in the same directory +- mediatek,pericfg: A phandle to the syscon node that control ethernet + interface and timing delay. + +Optional properties: +- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. + It should be defined for RGMII/MII interface. +- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0. + It should be defined for RGMII/MII/RMII interface. +Both delay properties need to be a multiple of 170 for RGMII interface, +or will round down. Range 0~31*170. +Both delay properties need to be a multiple of 550 for MII/RMII interface, +or will round down. Range 0~31*550. + +- mediatek,rmii-rxc: boolean property, if present indicates that the RMII + reference clock, which is from external PHYs, is connected to RXC pin + on MT2712 SoC. + Otherwise, is connected to TXC pin. +- mediatek,txc-inverse: boolean property, if present indicates that + 1. tx clock will be inversed in MII/RGMII case, + 2. tx clock inside MAC will be inversed relative to reference clock + which is from external PHYs in RMII case, and it rarely happen. +- mediatek,rxc-inverse: boolean property, if present indicates that + 1. rx clock will be inversed in MII/RGMII case. + 2. reference clock will be inversed when arrived at MAC in RMII case. +- assigned-clocks: mac_main and ptp_ref clocks +- assigned-clock-parents: parent clocks of the assigned clocks + +Example: + eth: ethernet@1101c000 { + compatible = "mediatek,mt2712-gmac"; + reg = <0 0x1101c000 0 0x1300>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "macirq"; + phy-mode ="rgmii"; + mac-address = [00 55 7b b5 7d f7]; + clock-names = "axi", + "apb", + "mac_main", + "ptp_ref", + "ptp_top"; + clocks = <&pericfg CLK_PERI_GMAC>, + <&pericfg CLK_PERI_GMAC_PCLK>, + <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>; + assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, + <&topckgen CLK_TOP_APLL1_D3>; + mediatek,pericfg = <&pericfg>; + mediatek,tx-delay-ps = <1530>; + mediatek,rx-delay-ps = <1530>; + mediatek,rmii-rxc; + mediatek,txc-inverse; + mediatek,rxc-inverse; + snps,txpbl = <32>; + snps,rxpbl = <32>; + snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index e22d8cfea687..5100358177c9 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -1,4 +1,4 @@ -Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY +Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY Some boards require special tuning values, particularly when it comes to clock delays. You can specify clock delay values in the PHY OF @@ -64,6 +64,32 @@ KSZ9031: Attention: The link partner must be configurable as slave otherwise no link will be established. +KSZ9131: + + All skew control options are specified in picoseconds. The increment + step is 100ps. Unlike KSZ9031, the values represent picoseccond delays. + A negative value can be assigned as rxc-skew-psec = <(-100)>;. + + Optional properties: + + Range of the value -700 to 2400, default value 0: + + - rxc-skew-psec : Skew control of RX clock pad + - txc-skew-psec : Skew control of TX clock pad + + Range of the value -700 to 800, default value 0: + + - rxdv-skew-psec : Skew control of RX CTL pad + - txen-skew-psec : Skew control of TX CTL pad + - rxd0-skew-psec : Skew control of RX data 0 pad + - rxd1-skew-psec : Skew control of RX data 1 pad + - rxd2-skew-psec : Skew control of RX data 2 pad + - rxd3-skew-psec : Skew control of RX data 3 pad + - txd0-skew-psec : Skew control of TX data 0 pad + - txd1-skew-psec : Skew control of TX data 1 pad + - txd2-skew-psec : Skew control of TX data 2 pad + - txd3-skew-psec : Skew control of TX data 3 pad + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt index 0a84711abece..9e5c17d426ce 100644 --- a/Documentation/devicetree/bindings/net/mscc-ocelot.txt +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -12,7 +12,6 @@ Required properties: - "sys" - "rew" - "qs" - - "hsio" - "qsys" - "ana" - "portX" with X from 0 to the number of last port index available on that @@ -45,7 +44,6 @@ Example: reg = <0x1010000 0x10000>, <0x1030000 0x10000>, <0x1080000 0x100>, - <0x10d0000 0x10000>, <0x11e0000 0x100>, <0x11f0000 0x100>, <0x1200000 0x100>, @@ -59,10 +57,9 @@ Example: <0x1280000 0x100>, <0x1800000 0x80000>, <0x1880000 0x10000>; - reg-names = "sys", "rew", "qs", "hsio", "port0", - "port1", "port2", "port3", "port4", "port5", - "port6", "port7", "port8", "port9", "port10", - "qsys", "ana"; + reg-names = "sys", "rew", "qs", "port0", "port1", "port2", + "port3", "port4", "port5", "port6", "port7", + "port8", "port9", "port10", "qsys", "ana"; interrupts = <21 22>; interrupt-names = "xtr", "inj"; diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 0eedabe22cc3..5ff37c68c941 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -1,10 +1,5 @@ * Microsemi - vsc8531 Giga bit ethernet phy -Required properties: -- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" - The PHY device uses the binding described in - Documentation/devicetree/bindings/net/phy.txt - Optional properties: - vsc8531,vddmac : The vddmac in mV. Allowed values is listed in the first row of Table 1 (below). @@ -27,14 +22,16 @@ Optional properties: 'vddmac'. Default value is 0%. Ref: Table:1 - Edge rate change (below). -- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. - Allowed values are define in - "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_1000_ACTIVITY (1). -- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. - Allowed values are define in +- vsc8531,led-[N]-mode : LED mode. Specify how the LED[N] should behave. + N depends on the number of LEDs supported by a + PHY. + Allowed values are defined in "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_100_ACTIVITY (2). + Default values are VSC8531_LINK_1000_ACTIVITY (1), + VSC8531_LINK_100_ACTIVITY (2), + VSC8531_LINK_ACTIVITY (0) and + VSC8531_DUPLEX_COLLISION (8). + Table: 1 - Edge rate change ----------------------------------------------------------------| diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index da249b7c406c..7ad36213093e 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -6,6 +6,7 @@ interface contains. Required properties: - compatible: Must contain one or more of the following: - "renesas,etheravb-r8a7743" for the R8A7743 SoC. + - "renesas,etheravb-r8a7744" for the R8A7744 SoC. - "renesas,etheravb-r8a7745" for the R8A7745 SoC. - "renesas,etheravb-r8a77470" for the R8A77470 SoC. - "renesas,etheravb-r8a7790" for the R8A7790 SoC. @@ -17,6 +18,7 @@ Required properties: R-Car Gen2 and RZ/G1 devices. - "renesas,etheravb-r8a774a1" for the R8A774A1 SoC. + - "renesas,etheravb-r8a774c0" for the R8A774C0 SoC. - "renesas,etheravb-r8a7795" for the R8A7795 SoC. - "renesas,etheravb-r8a7796" for the R8A7796 SoC. - "renesas,etheravb-r8a77965" for the R8A77965 SoC. diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 7fd4e8ce4149..ae661e65354e 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -21,10 +21,22 @@ can be provided per device. SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi". -Optional properties: - reg: Address and length of the register set for the device. - reg-names: Must include the list of following reg names, "membase" +- interrupts: reference to the list of 17 interrupt numbers for "qcom,ipq4019-wifi" + compatible target. + reference to the list of 12 interrupt numbers for "qcom,wcn3990-wifi" + compatible target. + Must contain interrupt-names property per entry for + "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets. + +- interrupt-names: Must include the entries for MSI interrupt + names ("msi0" to "msi15") and legacy interrupt + name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi" + compatible targets. + +Optional properties: - resets: Must contain an entry for each entry in reset-names. See ../reset/reseti.txt for details. - reset-names: Must include the list of following reset names, @@ -37,12 +49,9 @@ Optional properties: - clocks: List of clock specifiers, must contain an entry for each required entry in clock-names. - clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", - "wifi_wcss_rtc". -- interrupts: List of interrupt lines. Must contain an entry - for each entry in the interrupt-names property. -- interrupt-names: Must include the entries for MSI interrupt - names ("msi0" to "msi15") and legacy interrupt - name ("legacy"), + "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and + "cxo_ref_clk_pin" for "qcom,wcn3990-wifi" + compatible target. - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into MSI address register. @@ -55,9 +64,25 @@ Optional properties: - qcom,ath10k-pre-calibration-data : pre calibration data as an array, the length can vary between hw versions. - <supply-name>-supply: handle to the regulator device tree node - optional "supply-name" is "vdd-0.8-cx-mx". + optional "supply-name" are "vdd-0.8-cx-mx", + "vdd-1.8-xo", "vdd-1.3-rfa" and "vdd-3.3-ch0". +- memory-region: + Usage: optional + Value type: <phandle> + Definition: reference to the reserved-memory for the msa region + used by the wifi firmware running in Q6. +- iommus: + Usage: optional + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. +- ext-fem-name: + Usage: Optional + Value type: string + Definition: Name of external front end module used. Some valid FEM names + for example: "microsemi-lx5586", "sky85703-11" + and "sky85803" etc. -Example (to supply the calibration data alone): +Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller. @@ -69,10 +94,10 @@ pci { #address-cells = <3>; device_type = "pci"; - ath10k@0,0 { + wifi@0,0 { reg = <0 0 0 0 0>; - device_type = "pci"; qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + ext-fem-name = "microsemi-lx5586"; }; }; }; @@ -133,20 +158,25 @@ wifi@18000000 { compatible = "qcom,wcn3990-wifi"; reg = <0x18800000 0x800000>; reg-names = "membase"; - clocks = <&clock_gcc clk_aggre2_noc_clk>; - clock-names = "smmu_aggre2_noc_clk" + clocks = <&clock_gcc clk_rf_clk2_pin>; + clock-names = "cxo_ref_clk_pin"; interrupts = - <0 130 0 /* CE0 */ >, - <0 131 0 /* CE1 */ >, - <0 132 0 /* CE2 */ >, - <0 133 0 /* CE3 */ >, - <0 134 0 /* CE4 */ >, - <0 135 0 /* CE5 */ >, - <0 136 0 /* CE6 */ >, - <0 137 0 /* CE7 */ >, - <0 138 0 /* CE8 */ >, - <0 139 0 /* CE9 */ >, - <0 140 0 /* CE10 */ >, - <0 141 0 /* CE11 */ >; + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>; vdd-0.8-cx-mx-supply = <&pm8998_l5>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + memory-region = <&wifi_msa_mem>; + iommus = <&apps_smmu 0x0040 0x1>; }; |