diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c')
83 files changed, 7622 insertions, 1074 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt deleted file mode 100644 index 552b6a82cb1f..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/adv7180.txt +++ /dev/null @@ -1,49 +0,0 @@ -* Analog Devices ADV7180 analog video decoder family - -The adv7180 family devices are used to capture analog video to different -digital interfaces like MIPI CSI-2 or parallel video. - -Required Properties : -- compatible : value must be one of - "adi,adv7180" - "adi,adv7180cp" - "adi,adv7180st" - "adi,adv7182" - "adi,adv7280" - "adi,adv7280-m" - "adi,adv7281" - "adi,adv7281-m" - "adi,adv7281-ma" - "adi,adv7282" - "adi,adv7282-m" - -Device nodes of "adi,adv7180cp" and "adi,adv7180st" must contain one -'port' child node per device input and output port, in accordance with the -video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. The port -nodes are numbered as follows. - - Port adv7180cp adv7180st -------------------------------------------------------------------- - Input 0-2 0-5 - Output 3 6 - -The digital output port node must contain at least one endpoint. - -Optional Properties : -- powerdown-gpios: reference to the GPIO connected to the powerdown pin, - if any. - - -Example: - - i2c0@1c22000 { - ... - ... - adv7180@21 { - compatible = "adi,adv7180"; - reg = <0x21>; - }; - ... - }; - diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.yaml b/Documentation/devicetree/bindings/media/i2c/adv7180.yaml new file mode 100644 index 000000000000..c8d887eee3bb --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7180.yaml @@ -0,0 +1,179 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adv7180.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV7180 analog video decoder family + +maintainers: + - Lars-Peter Clausen <lars@metafoo.de> + +description: + The adv7180 family devices are used to capture analog video to different + digital interfaces like MIPI CSI-2 or parallel video. + +properties: + compatible: + items: + - enum: + - adi,adv7180 + - adi,adv7180cp + - adi,adv7180st + - adi,adv7182 + - adi,adv7280 + - adi,adv7280-m + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + - adi,adv7282 + - adi,adv7282-m + + reg: + maxItems: 1 + + powerdown-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + adv,force-bt656-4: + description: + Indicates that the output is a BT.656-4 compatible stream. + type: boolean + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + ports: true + +additionalProperties: false + +required: + - compatible + - reg + +allOf: + - if: + properties: + compatible: + enum: + - adi,adv7180 + - adi,adv7182 + - adi,adv7280 + - adi,adv7280-m + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + - adi,adv7282 + - adi,adv7282-m + then: + required: + - port + + - if: + properties: + compatible: + contains: + const: adi,adv7180cp + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + patternProperties: + "^port@[0-2]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + required: + - port@3 + + required: + - ports + + - if: + properties: + compatible: + contains: + const: adi,adv7180st + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@6: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + patternProperties: + "^port@[0-5]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + required: + - port@6 + + required: + - ports + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep>; + }; + }; + }; + + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7180cp"; + reg = <0x20>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7180_in: endpoint { + remote-endpoint = <&composite_con_in>; + }; + }; + + port@3 { + reg = <3>; + adv7180_out: endpoint { + remote-endpoint = <&vin4_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt deleted file mode 100644 index 4f91686e54a6..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/adv748x.txt +++ /dev/null @@ -1,116 +0,0 @@ -* Analog Devices ADV748X video decoder with HDMI receiver - -The ADV7481 and ADV7482 are multi format video decoders with an integrated -HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB -from three input sources HDMI, analog and TTL. - -Required Properties: - - - compatible: Must contain one of the following - - "adi,adv7481" for the ADV7481 - - "adi,adv7482" for the ADV7482 - - - reg: I2C slave addresses - The ADV748x has up to twelve 256-byte maps that can be accessed via the - main I2C ports. Each map has it own I2C address and acts as a standard - slave device on the I2C bus. The main address is mandatory, others are - optional and remain at default values if not specified. - -Optional Properties: - - - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or - "intrq3". All interrupts are optional. The "intrq3" interrupt - is only available on the adv7481 - - interrupts: Specify the interrupt lines for the ADV748x - - reg-names : Names of maps with programmable addresses. - It shall contain all maps needing a non-default address. - Possible map names are: - "main", "dpll", "cp", "hdmi", "edid", "repeater", - "infoframe", "cbus", "cec", "sdp", "txa", "txb" - -The device node must contain one 'port' child node per device input and output -port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes -are numbered as follows. - - Name Type Port - --------------------------------------- - AIN0 sink 0 - AIN1 sink 1 - AIN2 sink 2 - AIN3 sink 3 - AIN4 sink 4 - AIN5 sink 5 - AIN6 sink 6 - AIN7 sink 7 - HDMI sink 8 - TTL sink 9 - TXA source 10 - TXB source 11 - -The digital output port nodes, when present, shall contain at least one -endpoint. Each of those endpoints shall contain the data-lanes property as -described in video-interfaces.txt. - -Required source endpoint properties: - - data-lanes: an array of physical data lane indexes - The accepted value(s) for this property depends on which of the two - sources are described. For TXA 1, 2 or 4 data lanes can be described - while for TXB only 1 data lane is valid. See video-interfaces.txt - for detailed description. - -Ports are optional if they are not connected to anything at the hardware level. - -Example: - - video-receiver@70 { - compatible = "adi,adv7482"; - reg = <0x70 0x71 0x72 0x73 0x74 0x75 - 0x60 0x61 0x62 0x63 0x64 0x65>; - reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", - "infoframe", "cbus", "cec", "sdp", "txa", "txb"; - - #address-cells = <1>; - #size-cells = <0>; - - interrupt-parent = <&gpio6>; - interrupt-names = "intrq1", "intrq2"; - interrupts = <30 IRQ_TYPE_LEVEL_LOW>, - <31 IRQ_TYPE_LEVEL_LOW>; - - port@7 { - reg = <7>; - - adv7482_ain7: endpoint { - remote-endpoint = <&cvbs_in>; - }; - }; - - port@8 { - reg = <8>; - - adv7482_hdmi: endpoint { - remote-endpoint = <&hdmi_in>; - }; - }; - - port@a { - reg = <10>; - - adv7482_txa: endpoint { - clock-lanes = <0>; - data-lanes = <1 2 3 4>; - remote-endpoint = <&csi40_in>; - }; - }; - - port@b { - reg = <11>; - - adv7482_txb: endpoint { - clock-lanes = <0>; - data-lanes = <1>; - remote-endpoint = <&csi20_in>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.yaml b/Documentation/devicetree/bindings/media/i2c/adv748x.yaml new file mode 100644 index 000000000000..d6353081402b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.yaml @@ -0,0 +1,212 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adv748x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV748X video decoder with HDMI receiver + +maintainers: + - Kieran Bingham <kieran.bingham@ideasonboard.com> + - Niklas Sรถderlund <niklas.soderlund@ragnatech.se> + +description: + The ADV7481 and ADV7482 are multi format video decoders with an integrated + HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB + from three input sources HDMI, analog and TTL. + +properties: + compatible: + items: + - enum: + - adi,adv7481 + - adi,adv7482 + + reg: + minItems: 1 + maxItems: 12 + description: + The ADV748x has up to twelve 256-byte maps that can be accessed via the + main I2C ports. Each map has it own I2C address and acts as a standard + slave device on the I2C bus. The main address is mandatory, others are + optional and remain at default values if not specified. + + reg-names: + minItems: 1 + items: + - const: main + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + + interrupts: true + + interrupt-names: true + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + patternProperties: + "^port@[0-7]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port nodes for analog inputs AIN[0-7]. + + properties: + port@8: + $ref: /schemas/graph.yaml#/properties/port + description: Input port node for HDMI. + + port@9: + $ref: /schemas/graph.yaml#/properties/port + description: Input port node for TTL. + + port@a: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter TXA. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - clock-lanes + - data-lanes + + port@b: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter TXB. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + maxItems: 1 + + required: + - clock-lanes + - data-lanes + +allOf: + - if: + properties: + compatible: + contains: + const: adi,adv7481 + then: + properties: + interrupts: + minItems: 1 + maxItems: 3 + + interrupt-names: + minItems: 1 + maxItems: 3 + items: + enum: [ intrq1, intrq2, intrq3 ] + else: + properties: + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + minItems: 1 + maxItems: 2 + items: + enum: [ intrq1, intrq2 ] + +additionalProperties: false + +required: + - compatible + - reg + - ports + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + video-receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70 0x71 0x72 0x73 0x74 0x75 + 0x60 0x61 0x62 0x63 0x64 0x65>; + reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", + "infoframe", "cbus", "cec", "sdp", "txa", "txb"; + + interrupt-parent = <&gpio6>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, <31 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "intrq1", "intrq2"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@a { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@b { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt deleted file mode 100644 index b3e688b77a38..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ /dev/null @@ -1,88 +0,0 @@ -* Analog Devices ADV7604/11/12 video decoder with HDMI receiver - -The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated -HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog -input, and the ADV7611 has one HDMI input and no analog input. The 7612 is -similar to the 7611 but has 2 HDMI inputs. - -These device tree bindings support the ADV7611/12 only at the moment. - -Required Properties: - - - compatible: Must contain one of the following - - "adi,adv7611" for the ADV7611 - - "adi,adv7612" for the ADV7612 - - - reg: I2C slave addresses - The ADV76xx has up to thirteen 256-byte maps that can be accessed via the - main I2C ports. Each map has it own I2C address and acts as a standard - slave device on the I2C bus. The main address is mandatory, others are - optional and revert to defaults if not specified. - - - hpd-gpios: References to the GPIOs that control the HDMI hot-plug - detection pins, one per HDMI input. The active flag indicates the GPIO - level that enables hot-plug detection. - -The device node must contain one 'port' child node per device input and output -port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes -are numbered as follows. - - Port ADV7611 ADV7612 ------------------------------------------------------------- - HDMI 0 0, 1 - Digital output 1 2 - -The digital output port node must contain at least one endpoint. - -Optional Properties: - - - reset-gpios: Reference to the GPIO connected to the device's reset pin. - - default-input: Select which input is selected after reset. - - reg-names : Names of maps with programmable addresses. - It can contain any map needing a non-default address. - Possible maps names are : - "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", - "rep", "edid", "hdmi", "test", "cp", "vdp" - -Optional Endpoint Properties: - - The following three properties are defined in video-interfaces.txt and are - valid for source endpoints only. - - - hsync-active: Horizontal synchronization polarity. Defaults to active low. - - vsync-active: Vertical synchronization polarity. Defaults to active low. - - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. - - If none of hsync-active, vsync-active and pclk-sample is specified the - endpoint will use embedded BT.656 synchronization. - -Example: - - hdmi_receiver@4c { - compatible = "adi,adv7611"; - /* - * The edid page will be accessible @ 0x66 on the I2C bus. All - * other maps will retain their default addresses. - */ - reg = <0x4c>, <0x66>; - reg-names = "main", "edid"; - - reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; - hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; - - #address-cells = <1>; - #size-cells = <0>; - - default-input = <0>; - - port@0 { - reg = <0>; - }; - port@1 { - reg = <1>; - hdmi_in: endpoint { - remote-endpoint = <&ccdc_in>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.yaml b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml new file mode 100644 index 000000000000..7589d377c686 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adv7604.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV7604/10/11/12 video decoder with HDMI receiver + +maintainers: + - Hans Verkuil <hverkuil-cisco@xs4all.nl> + +description: + The ADV7604 and ADV7610/11/12 are multiformat video decoders with + an integrated HDMI receiver. The ADV7604 has four multiplexed HDMI inputs + and one analog input, and the ADV7610/11 have one HDMI input and no analog + input. The ADV7612 is similar to the ADV7610/11 but has 2 HDMI inputs. + + These device tree bindings support the ADV7610/11/12 only at the moment. + +properties: + compatible: + items: + - enum: + - adi,adv7610 + - adi,adv7611 + - adi,adv7612 + + reg: + minItems: 1 + maxItems: 13 + + reg-names: + minItems: 1 + items: + - const: main + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + hpd-gpios: + minItems: 1 + description: + References to the GPIOs that control the HDMI hot-plug detection pins, + one per HDMI input. The active flag indicates the GPIO level that + enables hot-plug detection. + + default-input: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Select which input is selected after reset. + + ports: true + +required: + - compatible + - reg + - ports + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: adi,adv7611 + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + required: + - port@1 + + - if: + properties: + compatible: + contains: + const: adi,adv7612 + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + patternProperties: + "^port@[0-1]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + required: + - port@2 + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + /* + * The edid page will be accessible @ 0x66 on the I2C bus. All + * other maps will retain their default addresses. + */ + reg = <0x4c>, <0x66>; + reg-names = "main", "edid"; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + default-input = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; + + + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ak7375.txt b/Documentation/devicetree/bindings/media/i2c/ak7375.txt deleted file mode 100644 index aa3e24b41241..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ak7375.txt +++ /dev/null @@ -1,8 +0,0 @@ -Asahi Kasei Microdevices AK7375 voice coil lens driver - -AK7375 is a camera voice coil lens. - -Mandatory properties: - -- compatible: "asahi-kasei,ak7375" -- reg: I2C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/alliedvision,alvium-csi2.yaml b/Documentation/devicetree/bindings/media/i2c/alliedvision,alvium-csi2.yaml new file mode 100644 index 000000000000..d3329e991d16 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/alliedvision,alvium-csi2.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/alliedvision,alvium-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allied Vision Alvium Camera + +maintainers: + - Tommaso Merciai <tomm.merciai@gmail.com> + - Martin Hecht <martin.hecht@avnet.eu> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: alliedvision,alvium-csi2 + + reg: + maxItems: 1 + + vcc-ext-in-supply: + description: | + The regulator that supplies power to the VCC_EXT_IN pins. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - vcc-ext-in-supply + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + alvium: camera@3c { + compatible = "alliedvision,alvium-csi2"; + reg = <0x3c>; + vcc-ext-in-supply = <®_vcc_ext_in>; + + port { + alvium_out: endpoint { + remote-endpoint = <&mipi_csi_0_in>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <681250000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml new file mode 100644 index 000000000000..be00de2f2d58 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/aptina,mt9p031.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: | + The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor + with an active array size of 2592H x 1944V. It is programmable through a + simple two-wire serial interface. + +properties: + compatible: + enum: + - aptina,mt9p006 + - aptina,mt9p031 + - aptina,mt9p031m + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + vdd-supply: + description: Digital supply voltage, 1.8 V + + vdd_io-supply: + description: I/O supply voltage, 1.8 or 2.8 V + + vaa-supply: + description: Analog supply voltage, 2.8 V + + reset-gpios: + maxItems: 1 + description: Chip reset GPIO + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + input-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 6000000 + maximum: 96000000 + description: Input clock frequency + + pixel-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 96000000 + description: Target pixel clock frequency + + pclk-sample: + default: 0 + + required: + - input-clock-frequency + - pixel-clock-frequency + +required: + - compatible + - reg + - clocks + - vdd-supply + - vdd_io-supply + - vaa-supply + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + mt9p031@5d { + compatible = "aptina,mt9p031"; + reg = <0x5d>; + reset-gpios = <&gpio_sensor 0 0>; + + clocks = <&sensor_clk>; + + vdd-supply = <®_vdd>; + vdd_io-supply = <®_vdd_io>; + vaa-supply = <®_vaa>; + + port { + mt9p031_1: endpoint { + input-clock-frequency = <6000000>; + pixel-clock-frequency = <96000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt deleted file mode 100644 index bd896e9f67d1..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt +++ /dev/null @@ -1,46 +0,0 @@ -* Aptina MT9V111 CMOS sensor ----------------------------- - -The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core -based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). - -The sensor has an active pixel array of 640x480 pixels and can output a number -of image resolution and formats controllable through a simple two-wires -interface. - -Required properties: --------------------- - -- compatible: shall be "aptina,mt9v111". -- clocks: reference to the system clock input provider. - -Optional properties: --------------------- - -- enable-gpios: output enable signal, pin name "OE#". Active low. -- standby-gpios: low power state control signal, pin name "STANDBY". - Active high. -- reset-gpios: chip reset signal, pin name "RESET#". Active low. - -The device node must contain one 'port' child node with one 'endpoint' child -sub-node for its digital output video port, in accordance with the video -interface bindings defined in: -Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: --------- - - &i2c1 { - camera@48 { - compatible = "aptina,mt9v111"; - reg = <0x48>; - - clocks = <&camera_clk>; - - port { - mt9v111_out: endpoint { - remote-endpoint = <&ceu_in>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml new file mode 100644 index 000000000000..088022f88010 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/aptina,mt9v111.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Aptina MT9V111 CMOS sensor + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + +description: | + The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core + based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). + + The sensor has an active pixel array of 640x480 pixels and can output a number + of image resolutions and formats controllable through a simple two-wires + interface. + +properties: + compatible: + const: aptina,mt9v111 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + enable-gpios: + description: Enable signal, pin name "OE#". Active low. + maxItems: 1 + + standby-gpios: + description: | + Low power state control signal, pin name "STANDBY". Active high. + maxItems: 1 + + reset-gpios: + description: Chip reset signal, pin name "RESET#". Active low. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: | + Output video port. + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + clocks = <&camera_clk>; + + port { + mt9v111_out: endpoint { + remote-endpoint = <&ceu_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/asahi-kasei,ak7375.yaml b/Documentation/devicetree/bindings/media/i2c/asahi-kasei,ak7375.yaml new file mode 100644 index 000000000000..fe312cc6a873 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/asahi-kasei,ak7375.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/asahi-kasei,ak7375.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Asahi Kasei Microdevices AK7375 voice coil lens actuator + +maintainers: + - Tianshu Qiu <tian.shu.qiu@intel.com> + +description: + AK7375 is a voice coil motor (VCM) camera lens actuator that + is controlled over I2C. + +properties: + compatible: + enum: + - asahi-kasei,ak7345 + - asahi-kasei,ak7375 + + reg: + maxItems: 1 + + vdd-supply: + description: VDD supply + + vio-supply: + description: I/O pull-up supply + +required: + - compatible + - reg + - vdd-supply + - vio-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ak7375: camera-lens@c { + compatible = "asahi-kasei,ak7375"; + reg = <0x0c>; + + vdd-supply = <&vreg_l23a_2p8>; + vio-supply = <&vreg_lvs1a_1p8>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml new file mode 100644 index 000000000000..4e69b6a7ffcc --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/chrontel,ch7322.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chrontel HDMI-CEC Controller + +maintainers: + - Jeff Chase <jnchase@google.com> + +description: + The Chrontel CH7322 is a discrete HDMI-CEC controller. It is + programmable through I2C and drives a single CEC line. + +allOf: + - $ref: /schemas/media/cec/cec-common.yaml# + +properties: + compatible: + const: chrontel,ch7322 + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + description: + Reference to the GPIO connected to the RESET pin, if any. This + pin is active-low. + maxItems: 1 + + standby-gpios: + description: + Reference to the GPIO connected to the OE pin, if any. When low + the device will respond to power status requests with "standby" + if in auto mode. + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + cec@75 { + compatible = "chrontel,ch7322"; + reg = <0x75>; + interrupts = <47 IRQ_TYPE_EDGE_RISING>; + standby-gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + hdmi-phandle = <&hdmi>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt deleted file mode 100644 index b88dcdd41def..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt +++ /dev/null @@ -1,9 +0,0 @@ -Dongwoon Anatech DW9714 camera voice coil lens driver - -DW9174 is a 10-bit DAC with current sink capability. It is intended -for driving voice coil lenses in camera modules. - -Mandatory properties: - -- compatible: "dongwoon,dw9714" -- reg: IยฒC slave address diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml new file mode 100644 index 000000000000..66229a3dc05d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9714.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9714 camera voice coil lens driver + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: + DW9174 is a 10-bit DAC with current sink capability. It is intended for + driving voice coil lenses in camera modules. + +properties: + compatible: + const: dongwoon,dw9714 + + reg: + maxItems: 1 + + powerdown-gpios: + description: + XSD pin for shutdown (active low) + + vcc-supply: + description: VDD power supply + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-lens@c { + compatible = "dongwoon,dw9714"; + reg = <0x0c>; + vcc-supply = <®_csi_1v8>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml new file mode 100644 index 000000000000..a0855d3b7577 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9768.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9768 Voice Coil Motor (VCM) Lens + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Dongwoon DW9768 is a single 10-bit digital-to-analog (DAC) converter + with 100 mA output current sink capability. VCM current is controlled with + a linear mode driver. The DAC is controlled via a 2-wire (I2C-compatible) + serial interface that operates at clock rates up to 1MHz. This chip + integrates Advanced Actuator Control (AAC) technology and is intended for + driving voice coil lenses in camera modules. + +properties: + compatible: + enum: + - dongwoon,dw9768 # for DW9768 VCM + - giantec,gt9769 # for GT9769 VCM + + reg: + maxItems: 1 + + vin-supply: + description: + Definition of the regulator used as Digital I/O voltage supply. + + vdd-supply: + description: + Definition of the regulator used as Digital core voltage supply. + + dongwoon,aac-mode: + description: + Indication of AAC mode select. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 1 # AAC2 mode(operation time# 0.48 x Tvib) + - 2 # AAC3 mode(operation time# 0.70 x Tvib) + - 3 # AAC4 mode(operation time# 0.75 x Tvib) + - 5 # AAC8 mode(operation time# 1.13 x Tvib) + default: 2 + + dongwoon,aac-timing: + description: + Number of AAC Timing count that controlled by one 6-bit period of + vibration register AACT[5:0], the unit of which is 100 us. + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0x20 + minimum: 0x00 + maximum: 0x3f + + dongwoon,clock-presc: + description: + Indication of VCM internal clock dividing rate select, as one multiple + factor to calculate VCM ring periodic time Tvib. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # Dividing Rate - 2 + - 1 # Dividing Rate - 1 + - 2 # Dividing Rate - 1/2 + - 3 # Dividing Rate - 1/4 + - 4 # Dividing Rate - 8 + - 5 # Dividing Rate - 4 + default: 1 + +required: + - compatible + - reg + - vin-supply + - vdd-supply + +additionalProperties: false + +examples: + - | + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dw9768: camera-lens@c { + compatible = "dongwoon,dw9768"; + reg = <0x0c>; + + vin-supply = <&mt6358_vcamio_reg>; + vdd-supply = <&mt6358_vcama2_reg>; + dongwoon,aac-timing = <0x39>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt deleted file mode 100644 index c4701f1eaaf6..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt +++ /dev/null @@ -1,9 +0,0 @@ -Dongwoon Anatech DW9807 voice coil lens driver - -DW9807 is a 10-bit DAC with current sink capability. It is intended for -controlling voice coil lenses. - -Mandatory properties: - -- compatible: "dongwoon,dw9807-vcm" -- reg: I2C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml new file mode 100644 index 000000000000..aae246ca3fcf --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2018, 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9807-vcm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9807 voice coil lens driver + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: | + DW9807 is a 10-bit DAC with current sink capability. It is intended for + controlling voice coil lenses. + +properties: + compatible: + const: dongwoon,dw9807-vcm + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + lens@e { + compatible = "dongwoon,dw9807-vcm"; + reg = <0x0e>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml new file mode 100644 index 000000000000..f81e7daed67b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc0308.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Galaxycore GC0308 and GC0309 Image Sensors + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: | + The GalaxyCore GC0308 (1/6.5") and GC0309 (1/9") are 640x480 VGA sensors + programmable through an I2C interface and connected via parallel bus. + They include an ISP capable of auto exposure and auto white balance. + +allOf: + - $ref: ../video-interface-devices.yaml# + +properties: + compatible: + oneOf: + - const: galaxycore,gc0308 + - items: + - const: galaxycore,gc0309 + - const: galaxycore,gc0308 + + reg: + const: 0x21 + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + reset-gpios: + description: GPIO descriptor for the reset pin. + maxItems: 1 + + powerdown-gpios: + description: GPIO descriptor for the powerdown pin. + maxItems: 1 + + vdd28-supply: + description: 2.8V supply + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: true + data-shift: true + hsync-active: true + vsync-active: true + data-active: true + pclk-sample: true + + required: + - bus-width + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - powerdown-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@21 { + compatible = "galaxycore,gc0308"; + reg = <0x21>; + clocks = <&camera_clk>; + powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + vdd28-supply = <&vdd28>; + + port { + gc0308_ep: endpoint { + remote-endpoint = <¶llel_from_gc0308>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <1>; /* active high */ + vsync-active = <1>; /* active high */ + data-active = <1>; /* active high */ + pclk-sample = <1>; /* sample on rising edge */ + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml new file mode 100644 index 000000000000..1726ecca4c77 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc2145.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Galaxy Core 1/5'' UXGA CMOS Image Sensor + +maintainers: + - Alain Volmat <alain.volmat@foss.st.com> + +description: + The Galaxy Core GC2145 is a 2 Megapixel CMOS image sensor, for mobile + phone camera applications and digital camera products. GC2145 incorporates a + 1616V x 1232H active pixel array, on-chip 10-bit ADC, and image signal + processor allowing AE/AWB/interpolation/de-noise/color-conversion and + gamma correction. Bayer RGB, RGB565 and YCbCr 4:2:2 can be provided by the + sensor. It is programmable through an I2C interface. Image data is sent + either through a parallel interface or through MIPI CSI-2. + +allOf: + - $ref: ../video-interface-devices.yaml# + +properties: + compatible: + const: galaxycore,gc2145 + + reg: + const: 0x3c + + clocks: + maxItems: 1 + + powerdown-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + iovdd-supply: + description: Power Supply for I/O circuits (1.7 - 3V). + + avdd-supply: + description: Power for analog circuit/sensor array (2.7 - 3V). + + dvdd-supply: + description: Power for digital core (1.7 - 1.9V). + + orientation: true + + rotation: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + required: + - link-frequencies + + required: + - endpoint + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - powerdown-gpios + - reset-gpios + - iovdd-supply + - avdd-supply + - dvdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "galaxycore,gc2145"; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + iovdd-supply = <&scmi_v3v3_sw>; + avdd-supply = <&scmi_v3v3_sw>; + dvdd-supply = <&scmi_v3v3_sw>; + powerdown-gpios = <&mcp23017 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + reset-gpios = <&mcp23017 4 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + + port { + endpoint { + remote-endpoint = <&mipid02_0>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <120000000 192000000 240000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml new file mode 100644 index 000000000000..60f19e1152b3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor + +maintainers: + - Martin Kepplinger <martin.kepplinger@puri.sm> + +description: |- + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data + interface and CCI (I2C compatible) control bus. The output format + is raw Bayer. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: hynix,hi846 + + reg: + maxItems: 1 + + clocks: + items: + - description: Reference to the mclk clock. + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + reset-gpios: + description: Reference to the GPIO connected to the RESETB pin. Active low. + maxItems: 1 + + shutdown-gpios: + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low. + maxItems: 1 + + vddio-supply: + description: Definition of the regulator used for the VDDIO power supply. + + vdda-supply: + description: Definition of the regulator used for the VDDA power supply. + + vddd-supply: + description: Definition of the regulator used for the VDDD power supply. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - assigned-clocks + - assigned-clock-rates + - vddio-supply + - vdda-supply + - vddd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hi846: camera@20 { + compatible = "hynix,hi846"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_csi1>; + clocks = <&clk 0>; + assigned-clocks = <&clk 0>; + assigned-clock-rates = <25000000>; + vdda-supply = <®_camera_vdda>; + vddd-supply = <®_camera_vddd>; + vddio-supply = <®_camera_vddio>; + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>; + orientation = <0>; + rotation = <0>; + + port { + camera_out: endpoint { + remote-endpoint = <&csi1_ep1>; + link-frequencies = /bits/ 64 + <80000000 200000000>; + data-lanes = <1 2>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml new file mode 100644 index 000000000000..e57575c44930 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imi,rdacm2x-gmsl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IMI D&D RDACM20 and RDACM21 Automotive Camera Platforms + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Sรถderlund <niklas.soderlund+renesas@ragnatech.se> + +description: -| + The IMI D&D RDACM20 and RDACM21 are GMSL-compatible camera designed for + automotive applications. + + The RDACM20 camera module encloses a Maxim Integrated MAX9271 GMSL serializer, + coupled with an OV10635 image sensor and an embedded MCU. Both the MCU and + the image sensor are connected to the serializer local I2C bus and are + accessible by the host SoC by direct addressing. + + The RDACM21 camera module encloses the same serializer, coupled with an + OV10640 image sensor and an OV490 ISP. Only the OV490 ISP is interfaced to + the serializer local I2C bus while the image sensor is not accessible from + the host SoC. + + They both connect to a remote GMSL endpoint through a coaxial cable. + + IMI RDACM20 + +---------------+ +--------------------------------+ + | GMSL | <- Video Stream | <- Video--------\ | + | |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV10635 | + | de-serializer | <- I2C messages -> | \<-->MCU | + +---------------+ +--------------------------------+ + + IMI RDACM21 + +---------------+ +--------------------------------+ + | GMSL | <- Video Stream | <- Video--------\ | + | |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV490 | + | | <- I2C messages -> | | | + | de-serializer | | OV10640 <-------| | + +---------------+ +--------------------------------+ + + Both camera modules serialize video data generated by the embedded camera + sensor on the GMSL serial channel to a remote GMSL de-serializer. They also + receive and transmit I2C messages encapsulated and transmitted on the GMSL + bidirectional control channel. + + All I2C traffic received on the GMSL link not directed to the serializer is + propagated on the local I2C bus to the remote device there connected. All the + I2C traffic generated on the local I2C bus not directed to the serializer is + propagated to the remote de-serializer encapsulated in the GMSL control + channel. + + The RDACM20 and RDACM21 DT node should be a direct child of the GMSL + deserializer's I2C bus corresponding to the GMSL link that the camera is + attached to. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + enum: + - imi,rdacm20 + - imi,rdacm21 + + reg: + description: -| + I2C device addresses, the first to be assigned to the serializer, the + following ones to be assigned to the remote devices. + + For RDACM20 the second entry of the property is assigned to the + OV10635 image sensor and the optional third one to the embedded MCU. + + For RDACM21 the second entry is assigned to the OV490 ISP and the optional + third one ignored. + + minItems: 2 + maxItems: 3 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + Connection to the remote GMSL endpoint. + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + camera@31 { + compatible = "imi,rdacm20"; + reg = <0x31>, <0x41>, <0x51>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + }; + }; + + - | + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + camera@31 { + compatible = "imi,rdacm21"; + reg = <0x31>, <0x41>; + + port { + rdacm21_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.yaml b/Documentation/devicetree/bindings/media/i2c/imx219.yaml index 32d6b693274f..07d088cf66e0 100644 --- a/Documentation/devicetree/bindings/media/i2c/imx219.yaml +++ b/Documentation/devicetree/bindings/media/i2c/imx219.yaml @@ -40,16 +40,20 @@ properties: Digital core voltage supply, 1.2 volts reset-gpios: + maxItems: 1 description: |- Reference to the GPIO connected to the xclr pin, if any. Must be released (set high) after all supplies are applied. - # See ../video-interfaces.txt for more details port: - type: object + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + properties: endpoint: - type: object + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + properties: data-lanes: description: |- @@ -60,17 +64,8 @@ properties: - const: 1 - const: 2 - clock-noncontinuous: - type: boolean - description: |- - MIPI CSI-2 clock is non-continuous if this property is present, - otherwise it's continuous. - - link-frequencies: - allOf: - - $ref: /schemas/types.yaml#/definitions/uint64-array - description: - Allowed data bus frequencies. + clock-noncontinuous: true + link-frequencies: true required: - link-frequencies @@ -88,7 +83,7 @@ additionalProperties: false examples: - | - i2c0 { + i2c { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/media/i2c/imx258.yaml b/Documentation/devicetree/bindings/media/i2c/imx258.yaml new file mode 100644 index 000000000000..80d24220baa0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx258.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imx258.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: |- + IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel + type stacked image sensor with a square pixel array of size 4208 x 3120. It + is programmable through I2C interface. Image data is sent through MIPI + CSI-2. + +properties: + compatible: + const: sony,imx258 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: + Clock frequency from 6 to 27 MHz. + maxItems: 1 + + reg: + maxItems: 1 + + reset-gpios: + description: |- + Reference to the GPIO connected to the XCLR pin, if any. + + vana-supply: + description: + Analog voltage (VANA) supply, 2.7 V + + vdig-supply: + description: + Digital I/O voltage (VDIG) supply, 1.2 V + + vif-supply: + description: + Interface voltage (VIF) supply, 1.8 V + + # See ../video-interfaces.txt for more details + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <320000000>; + }; + }; + }; + }; + + /* Oscillator on the camera board */ + imx258_clk: clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + assigned-clocks = <&imx258_clk>; + assigned-clock-rates = <19200000>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <633600000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/imx274.txt b/Documentation/devicetree/bindings/media/i2c/imx274.txt deleted file mode 100644 index 80f2e89568e1..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/imx274.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor - -The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with -an active array size of 3864H x 2202V. It is programmable through I2C -interface. The I2C address is fixed to 0x1a as per sensor data sheet. -Image data is sent through MIPI CSI-2, which is configured as 4 lanes -at 1440 Mbps. - - -Required Properties: -- compatible: value should be "sony,imx274" for imx274 sensor -- reg: I2C bus address of the device - -Optional Properties: -- reset-gpios: Sensor reset GPIO - -The imx274 device node should contain one 'port' child node with -an 'endpoint' subnode. For further reading on port node refer to -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: - sensor@1a { - compatible = "sony,imx274"; - reg = <0x1a>; - #address-cells = <1>; - #size-cells = <0>; - reset-gpios = <&gpio_sensor 0 0>; - port { - sensor_out: endpoint { - remote-endpoint = <&csiss_in>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/imx290.txt b/Documentation/devicetree/bindings/media/i2c/imx290.txt deleted file mode 100644 index a3cc21410f7c..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/imx290.txt +++ /dev/null @@ -1,57 +0,0 @@ -* Sony IMX290 1/2.8-Inch CMOS Image Sensor - -The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with -Square Pixel for Color Cameras. It is programmable through I2C and 4-wire -interfaces. The sensor output is available via CMOS logic parallel SDR output, -Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the -default. No bindings have been defined for the other busses. - -Required Properties: -- compatible: Should be "sony,imx290" -- reg: I2C bus address of the device -- clocks: Reference to the xclk clock. -- clock-names: Should be "xclk". -- clock-frequency: Frequency of the xclk clock in Hz. -- vdddo-supply: Sensor digital IO regulator. -- vdda-supply: Sensor analog regulator. -- vddd-supply: Sensor digital core regulator. - -Optional Properties: -- reset-gpios: Sensor reset GPIO - -The imx290 device node should contain one 'port' child node with -an 'endpoint' subnode. For further reading on port node refer to -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Required Properties on endpoint: -- data-lanes: check ../video-interfaces.txt -- link-frequencies: check ../video-interfaces.txt -- remote-endpoint: check ../video-interfaces.txt - -Example: - &i2c1 { - ... - imx290: camera-sensor@1a { - compatible = "sony,imx290"; - reg = <0x1a>; - - reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&camera_rear_default>; - - clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; - clock-names = "xclk"; - clock-frequency = <37125000>; - - vdddo-supply = <&camera_vdddo_1v8>; - vdda-supply = <&camera_vdda_2v8>; - vddd-supply = <&camera_vddd_1v5>; - - port { - imx290_ep: endpoint { - data-lanes = <1 2 3 4>; - link-frequencies = /bits/ 64 <445500000>; - remote-endpoint = <&csiphy0_ep>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml b/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml new file mode 100644 index 000000000000..034a6e3466af --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/isil,isl79987.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intersil ISL79987 Analog to MIPI CSI-2 decoder + +maintainers: + - Michael Tretter <m.tretter@pengutronix.de> + - Marek Vasut <marex@denx.de> + +description: + The Intersil ISL79987 is an analog to MIPI CSI-2 decoder which is capable of + receiving up to four analog stream and multiplexing them into up to four MIPI + CSI-2 virtual channels, using one MIPI clock lane and 1/2 data lanes. + +properties: + compatible: + enum: + - isil,isl79987 + + reg: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: + A GPIO spec for the RSTB pin (active high) + + powerdown-gpios: + maxItems: 1 + description: + A GPIO spec for the Power Down pin (active high) + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + + patternProperties: + "^port@[1-4]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input ports + + required: + - port@0 + +additionalProperties: false + +required: + - compatible + - reg + - ports + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + isl7998x_mipi@44 { + compatible = "isil,isl79987"; + reg = <0x44>; + powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + isl79987_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&camera_0>; + }; + }; + + port@2 { + reg = <2>; + endpoint { + remote-endpoint = <&camera_1>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml new file mode 100644 index 000000000000..a37447256f8d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml @@ -0,0 +1,416 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated Quad GMSL Deserializer + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Sรถderlund <niklas.soderlund+renesas@ragnatech.se> + +description: | + The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia + Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data + lanes. + + In addition to video data, the GMSL links carry a bidirectional control + channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic + not addressed to itself to the other side of the links, where a GMSL + serializer will output it on a local I2C bus. In the other direction all I2C + traffic received over GMSL by the MAX9286 is output on the local I2C bus. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + const: maxim,max9286 + + reg: + description: I2C device address + maxItems: 1 + + poc-supply: + description: Regulator providing Power over Coax to all the ports + + enable-gpios: + description: GPIO connected to the \#PWDN pin with inverted polarity + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + maxim,bus-width: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 24, 27, 32 ] + description: | + The GMSL serial data bus width. This setting is normally controlled by + the BWS pin, but may be overridden with this property. The value must + match the configuration of the remote serializers. + + maxim,i2c-remote-bus-hz: + enum: [ 8470, 28300, 84700, 105000, 173000, 339000, 533000, 837000 ] + default: 105000 + description: | + The I2C clock frequency for the remote I2C buses. The value must match + the configuration of the remote serializers. + + maxim,reverse-channel-microvolt: + minimum: 30000 + maximum: 200000 + default: 170000 + description: | + Initial amplitude of the reverse control channel, in micro volts. + + The initial amplitude shall be adjusted to a value compatible with the + configuration of the connected remote serializer. + + Some camera modules (for example RDACM20) include an on-board MCU that + pre-programs the embedded serializer with power supply noise immunity + (high-threshold) enabled. A typical value of the deserializer's reverse + channel amplitude to communicate with pre-programmed serializers is + 170000 micro volts. + + A typical value for the reverse channel amplitude to communicate with + a remote serializer whose high-threshold noise immunity is not enabled + is 100000 micro volts + + maxim,gpio-poc: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: | + Index of the MAX9286 gpio output line (0 or 1) that controls Power over + Coax to the cameras and its associated polarity flag. + + The property accepts an array of two unsigned integers, the first being + the gpio line index (0 or 1) and the second being the gpio line polarity + flag (GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW) as defined in + <include/dt-bindings/gpio/gpio.h>. + + When the remote cameras power is controlled by one of the MAX9286 gpio + lines, this property has to be used to specify which line among the two + available ones controls the remote camera power enablement. + + When this property is used it is not possible to register a gpio + controller as the gpio lines are controlled directly by the MAX9286 and + not available for consumers, nor the 'poc-supply' property should be + specified. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 0 + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 1 + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 2 + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 3 + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + + required: + - data-lanes + + required: + - port@4 + + i2c-mux: + type: object + $ref: /schemas/i2c/i2c-mux.yaml# + unevaluatedProperties: false + description: | + Each GMSL link is modelled as a child bus of an i2c bus multiplexer/switch. + + patternProperties: + "^i2c@[0-3]$": + type: object + additionalProperties: false + description: | + Child node of the i2c bus multiplexer which represents a GMSL link. + Each serializer device on the GMSL link remote end is represented with + an i2c-mux child node. The MAX9286 chip supports up to 4 GMSL + channels. + + properties: + reg: + description: The index of the GMSL channel. + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + "^camera@[a-f0-9]+$": + type: object + description: | + The remote camera device, composed by a GMSL serializer and a + connected video source. + + properties: + compatible: + description: The remote device compatible string. + + reg: + minItems: 2 + maxItems: 3 + description: | + The I2C addresses to be assigned to the remote devices through + address reprogramming. The number of entries depends on the + requirements of the currently connected remote device. + + port: + $ref: /schemas/graph.yaml#/properties/port + description: Connection to the MAX9286 sink. + + required: + - compatible + - reg + - port + + additionalProperties: false + +patternProperties: + "^port[0-3]-poc-supply$": + description: Regulator providing Power over Coax for a particular port + +required: + - compatible + - reg + - ports + - i2c-mux + +allOf: + # Only one way of specifying power supplies is allowed: 'maxim,gpio-poc', + # 'poc-supply' or per-port poc-supply. Additionally, if 'maxim,gpio-poc' is + # present, then 'gpio-controller' isn't allowed. + - if: + required: + - maxim,gpio-poc + then: + properties: + poc-supply: false + gpio-controller: false + patternProperties: + "^port[0-3]-poc-supply$": false + + - if: + required: + - poc-supply + then: + patternProperties: + "^port[0-3]-poc-supply$": false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + gmsl-deserializer@2c { + compatible = "maxim,max9286"; + reg = <0x2c>; + poc-supply = <&camera_poc_12v>; + enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + maxim,i2c-remote-bus-hz = <339000>; + maxim,reverse-channel-microvolt = <170000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + max9286_in0: endpoint { + remote-endpoint = <&rdacm20_out0>; + }; + }; + + port@1 { + reg = <1>; + + max9286_in1: endpoint { + remote-endpoint = <&rdacm20_out1>; + }; + }; + + port@2 { + reg = <2>; + + max9286_in2: endpoint { + remote-endpoint = <&rdacm20_out2>; + }; + }; + + port@3 { + reg = <3>; + + max9286_in3: endpoint { + remote-endpoint = <&rdacm20_out3>; + }; + }; + + port@4 { + reg = <4>; + + max9286_out: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + camera@51 { + compatible = "imi,rdacm20"; + reg = <0x51>, <0x61>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + camera@52 { + compatible = "imi,rdacm20"; + reg = <0x52>, <0x62>; + + port { + rdacm20_out1: endpoint { + remote-endpoint = <&max9286_in1>; + }; + }; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + camera@53 { + compatible = "imi,rdacm20"; + reg = <0x53>, <0x63>; + + port { + rdacm20_out2: endpoint { + remote-endpoint = <&max9286_in2>; + }; + }; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + camera@54 { + compatible = "imi,rdacm20"; + reg = <0x54>, <0x64>; + + port { + rdacm20_out3: endpoint { + remote-endpoint = <&max9286_in3>; + }; + }; + }; + }; + }; + }; + + /* + * Example of a deserializer that controls the camera Power over Coax + * through one of its gpio lines. + */ + gmsl-deserializer@6c { + compatible = "maxim,max9286"; + reg = <0x6c>; + enable-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + + /* + * The remote camera power is controlled by MAX9286 GPIO line #0. + * No 'poc-supply' nor 'gpio-controller' are specified. + */ + maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>; + + /* + * Do not describe connections as they're the same as in the previous + * example. + */ + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml new file mode 100644 index 000000000000..6c72e77b927c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max96712.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Quad GMSL2 to CSI-2 Deserializer with GMSL1 Compatibility + +maintainers: + - Niklas Sรถderlund <niklas.soderlund+renesas@ragnatech.se> + +description: | + The MAX96712 deserializer converts GMSL2 or GMSL1 serial inputs into MIPI + CSI-2 D-PHY or C-PHY formatted outputs. The device allows each link to + simultaneously transmit bidirectional control-channel data while forward + video transmissions are in progress. The MAX96712 can accommodate as many as + four remotely located sensors using industry-standard coax or STP + interconnects. + + Each GMSL2 serial link operates at a fixed rate of 3Gbps or 6Gbps in the + forward direction and 187.5Mbps in the reverse direction. In GMSL1 mode, the + MAX96712 can be paired with first-generation 3.12Gbps or 1.5Gbps GMSL1 + serializers or operate up to 3.12Gbps with GMSL2 serializers in GMSL1 mode. + +properties: + compatible: + const: maxim,max96712 + + reg: + description: I2C device address + maxItems: 1 + + enable-gpios: true + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 0 + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 1 + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 2 + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 3 + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + - bus-type + + required: + - port@4 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe6508000>; + + gmsl0: gmsl-deserializer@49 { + compatible = "maxim,max96712"; + reg = <0x49>; + enable-gpios = <&pca9654_a 0 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + max96712_out0: endpoint { + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml new file mode 100644 index 000000000000..f8ace8cbccdb --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2014--2020 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/mipi-ccs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MIPI CCS, SMIA++ and SMIA compliant camera sensors + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: + + CCS (Camera Command Set) is a raw Bayer camera sensor standard defined by the + MIPI Alliance; see + <URL:https://www.mipi.org/specifications/camera-command-set>. + + SMIA (Standard Mobile Imaging Architecture) is an image sensor standard + defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension of + that. + + More detailed documentation can be found in + Documentation/devicetree/bindings/media/video-interfaces.txt . + +properties: + compatible: + oneOf: + - items: + - const: mipi-ccs-1.1 + - const: mipi-ccs + - items: + - const: mipi-ccs-1.0 + - const: mipi-ccs + - const: nokia,smia + + reg: + maxItems: 1 + + vana-supply: + description: Analogue voltage supply (VANA), sensor dependent. + + vcore-supply: + description: Core voltage supply (VCore), sensor dependent. + + vio-supply: + description: I/O voltage supply (VIO), sensor dependent. + + clocks: + description: External clock to the sensor. + maxItems: 1 + + clock-frequency: + description: Frequency of the external clock to the sensor in Hz. + + reset-gpios: + description: Reset GPIO. Also commonly called XSHUTDOWN in hardware + documentation. + maxItems: 1 + + flash-leds: + description: Flash LED phandles. See ../video-interfaces.txt for details. + + lens-focus: + description: Lens focus controller phandles. See ../video-interfaces.txt + for details. + + rotation: + description: Rotation of the sensor. See ../video-interfaces.txt for + details. + enum: [ 0, 180 ] + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + data-lanes: true + bus-type: + enum: + - 1 # CSI-2 C-PHY + - 3 # CCP2 + - 4 # CSI-2 D-PHY + + required: + - link-frequencies + - data-lanes + - bus-type + +required: + - compatible + - reg + - clock-frequency + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + clock-frequency = <400000>; + + camera-sensor@10 { + compatible = "mipi-ccs-1.0", "mipi-ccs"; + reg = <0x10>; + reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + port { + ccs_ep: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + link-frequencies = /bits/ 64 <199200000 210000000 + 499200000>; + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt deleted file mode 100644 index cb60443ff78f..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt +++ /dev/null @@ -1,40 +0,0 @@ -* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor - -The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with -an active array size of 2592H x 1944V. It is programmable through a simple -two-wire serial interface. - -Required Properties: -- compatible: value should be either one among the following - (a) "aptina,mt9p031" for mt9p031 sensor - (b) "aptina,mt9p031m" for mt9p031m sensor - -- input-clock-frequency: Input clock frequency. - -- pixel-clock-frequency: Pixel clock frequency. - -Optional Properties: -- reset-gpios: Chip reset GPIO - -For further reading on port node refer to -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: - - i2c0@1c22000 { - ... - ... - mt9p031@5d { - compatible = "aptina,mt9p031"; - reg = <0x5d>; - reset-gpios = <&gpio3 30 0>; - - port { - mt9p031_1: endpoint { - input-clock-frequency = <6000000>; - pixel-clock-frequency = <96000000>; - }; - }; - }; - ... - }; diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt deleted file mode 100644 index 10ece8108081..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ /dev/null @@ -1,66 +0,0 @@ -SMIA/SMIA++ sensor - -SMIA (Standard Mobile Imaging Architecture) is an image sensor standard -defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension -of that. These definitions are valid for both types of sensors. - -More detailed documentation can be found in -Documentation/devicetree/bindings/media/video-interfaces.txt . - -The device node should contain a "port" node which may contain one or more -endpoint nodes, in accordance with video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt . - -Mandatory properties --------------------- - -- compatible: "nokia,smia" -- reg: I2C address (0x10, or an alternative address) -- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor - dependent). -- clocks: External clock to the sensor -- clock-frequency: Frequency of the external clock to the sensor -- link-frequencies: List of allowed data link frequencies. An array of - 64-bit elements. - - -Optional properties -------------------- - -- reset-gpios: XSHUTDOWN GPIO -- flash-leds: See ../video-interfaces.txt -- lens-focus: See ../video-interfaces.txt -- rotation: Integer property; valid values are 0 (sensor mounted upright) - and 180 (sensor mounted upside down). See - ../video-interfaces.txt . - - -Endpoint node mandatory properties ----------------------------------- - -- data-lanes: <1..n> - - -Example -------- - -&i2c2 { - clock-frequency = <400000>; - - camera-sensor@10 { - compatible = "nokia,smia"; - reg = <0x10>; - reset-gpios = <&gpio3 20 0>; - vana-supply = <&vaux3>; - clocks = <&omap3_isp 0>; - clock-frequency = <9600000>; - nokia,nvm-size = <512>; /* 8 * 64 */ - link-frequencies = /bits/ 64 <199200000 210000000 499200000>; - port { - smiapp_ep: endpoint { - data-lanes = <1 2>; - remote-endpoint = <&csi2a_ep>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml b/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml new file mode 100644 index 000000000000..b617cc5c6a9f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/onnn,ar0521.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ON Semiconductor AR0521 MIPI CSI-2 sensor + +maintainers: + - Krzysztof Haลasa <khalasa@piap.pl> + +description: |- + The AR0521 is a raw CMOS image sensor with MIPI CSI-2 and + I2C-compatible control interface. + +properties: + compatible: + const: onnn,ar0521 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: extclk + + vaa-supply: + description: + Definition of the regulator used as analog (2.7 V) voltage supply. + + vdd-supply: + description: + Definition of the regulator used as digital core (1.2 V) voltage supply. + + vdd_io-supply: + description: + Definition of the regulator used as digital I/O (1.8 V) voltage supply. + + reset-gpios: + description: reset GPIO, usually active low + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + const: 4 + data-lanes: + anyOf: + - items: + - const: 1 + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + +required: + - compatible + - reg + - clocks + - clock-names + - vaa-supply + - vdd-supply + - vdd_io-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/imx6qdl-clock.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ar0521: camera-sensor@36 { + compatible = "onnn,ar0521"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mipi_camera>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "extclk"; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + vaa-supply = <®_2p7v>; + vdd-supply = <®_1p2v>; + vdd_io-supply = <®_1p8v>; + + port { + mipi_camera_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2 3 4>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/onnn,mt9m114.yaml b/Documentation/devicetree/bindings/media/i2c/onnn,mt9m114.yaml new file mode 100644 index 000000000000..f6b87892068a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/onnn,mt9m114.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/onnn,mt9m114.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: onsemi 1/6-inch 720p CMOS Digital Image Sensor + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The onsemi MT9M114 is a 1/6-inch 720p (1.26 Mp) CMOS digital image sensor + with an active pixel-array size of 1296H x 976V. It is programmable through + an I2C interface and outputs image data over a 8-bit parallel or 1-lane MIPI + CSI-2 connection. + +properties: + compatible: + const: onnn,mt9m114 + + reg: + description: I2C device address + enum: + - 0x48 + - 0x5d + + clocks: + description: EXTCLK clock signal + maxItems: 1 + + vdd-supply: + description: + Core digital voltage supply, 1.8V + + vddio-supply: + description: + I/O digital voltage supply, 1.8V or 2.8V + + vaa-supply: + description: + Analog voltage supply, 2.8V + + reset-gpios: + description: |- + Reference to the GPIO connected to the RESET_BAR pin, if any (active + low). + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + bus-type: + enum: [4, 5, 6] + + link-frequencies: true + remote-endpoint: true + + # The number and mapping of lanes (for CSI-2), and the bus width and + # signal polarities (for parallel and BT.656) are fixed and must not + # be specified. + + required: + - bus-type + - link-frequencies + +required: + - compatible + - reg + - clocks + - vdd-supply + - vddio-supply + - vaa-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "onnn,mt9m114"; + reg = <0x48>; + + clocks = <&clk24m 0>; + + reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + + vddio-supply = <®_cam_1v8>; + vdd-supply = <®_cam_1v8>; + vaa-supply = <®_2p8v>; + + port { + endpoint { + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + link-frequencies = /bits/ 64 <384000000>; + remote-endpoint = <&mipi_csi_in>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt deleted file mode 100644 index 11e925ed9dad..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov2680.txt +++ /dev/null @@ -1,46 +0,0 @@ -* Omnivision OV2680 MIPI CSI-2 sensor - -Required Properties: -- compatible: should be "ovti,ov2680". -- clocks: reference to the xvclk input clock. -- clock-names: should be "xvclk". -- DOVDD-supply: Digital I/O voltage supply. -- DVDD-supply: Digital core voltage supply. -- AVDD-supply: Analog voltage supply. - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the powerdown/reset pin, - if any. This is an active low signal to the OV2680. - -The device node must contain one 'port' child node for its digital output -video port, and this port must have a single endpoint in accordance with - the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Endpoint node required properties for CSI-2 connection are: -- remote-endpoint: a phandle to the bus receiver's endpoint node. -- clock-lanes: should be set to <0> (clock lane on hardware lane 0). -- data-lanes: should be set to <1> (one CSI-2 lane supported). - -Example: - -&i2c2 { - ov2680: camera-sensor@36 { - compatible = "ovti,ov2680"; - reg = <0x36>; - clocks = <&osc>; - clock-names = "xvclk"; - reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; - DOVDD-supply = <&sw2_reg>; - DVDD-supply = <&sw2_reg>; - AVDD-supply = <®_peri_3p15v>; - - port { - ov2680_to_mipi: endpoint { - remote-endpoint = <&mipi_from_sensor>; - clock-lanes = <0>; - data-lanes = <1>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2685.txt b/Documentation/devicetree/bindings/media/i2c/ov2685.txt deleted file mode 100644 index 625c4a8c0d53..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov2685.txt +++ /dev/null @@ -1,41 +0,0 @@ -* Omnivision OV2685 MIPI CSI-2 sensor - -Required Properties: -- compatible: shall be "ovti,ov2685" -- clocks: reference to the xvclk input clock -- clock-names: shall be "xvclk" -- avdd-supply: Analog voltage supply, 2.8 volts -- dovdd-supply: Digital I/O voltage supply, 1.8 volts -- dvdd-supply: Digital core voltage supply, 1.8 volts -- reset-gpios: Low active reset gpio - -The device node shall contain one 'port' child node with an -'endpoint' subnode for its digital output video port, -in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. -The endpoint optional property 'data-lanes' shall be "<1>". - -Example: -&i2c7 { - ov2685: camera-sensor@3c { - compatible = "ovti,ov2685"; - reg = <0x3c>; - pinctrl-names = "default"; - pinctrl-0 = <&clk_24m_cam>; - - clocks = <&cru SCLK_TESTCLKOUT1>; - clock-names = "xvclk"; - - avdd-supply = <&pp2800_cam>; - dovdd-supply = <&pp1800>; - dvdd-supply = <&pp1800>; - reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; - - port { - ucam_out: endpoint { - remote-endpoint = <&mipi_in_ucam>; - data-lanes = <1>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt deleted file mode 100644 index c97c2f2da12d..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt +++ /dev/null @@ -1,92 +0,0 @@ -* Omnivision OV5640 MIPI CSI-2 / parallel sensor - -Required Properties: -- compatible: should be "ovti,ov5640" -- clocks: reference to the xclk input clock. -- clock-names: should be "xclk". -- DOVDD-supply: Digital I/O voltage supply, 1.8 volts -- AVDD-supply: Analog voltage supply, 2.8 volts -- DVDD-supply: Digital core voltage supply, 1.5 volts - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the reset pin, if any. - This is an active low signal to the OV5640. -- powerdown-gpios: reference to the GPIO connected to the powerdown pin, - if any. This is an active high signal to the OV5640. -- rotation: as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt, - valid values are 0 (sensor mounted upright) and 180 (sensor - mounted upside down). - -The device node must contain one 'port' child node for its digital output -video port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. - -Endpoint node required properties for CSI-2 connection are: -- remote-endpoint: a phandle to the bus receiver's endpoint node. -- clock-lanes: should be set to <0> (clock lane on hardware lane 0) -- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) - -Endpoint node required properties for parallel connection are: -- remote-endpoint: a phandle to the bus receiver's endpoint node. -- bus-width: shall be set to <8> for 8 bits parallel bus - or <10> for 10 bits parallel bus -- data-shift: shall be set to <2> for 8 bits parallel bus - (lines 9:2 are used) or <0> for 10 bits parallel bus -- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. -- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock - signal. - -Examples: - -&i2c1 { - ov5640: camera@3c { - compatible = "ovti,ov5640"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ov5640>; - reg = <0x3c>; - clocks = <&clks IMX6QDL_CLK_CKO>; - clock-names = "xclk"; - DOVDD-supply = <&vgen4_reg>; /* 1.8v */ - AVDD-supply = <&vgen3_reg>; /* 2.8v */ - DVDD-supply = <&vgen2_reg>; /* 1.5v */ - powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; - rotation = <180>; - - port { - /* MIPI CSI-2 bus endpoint */ - ov5640_to_mipi_csi2: endpoint { - remote-endpoint = <&mipi_csi2_from_ov5640>; - clock-lanes = <0>; - data-lanes = <1 2>; - }; - }; - }; -}; - -&i2c1 { - ov5640: camera@3c { - compatible = "ovti,ov5640"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ov5640>; - reg = <0x3c>; - clocks = <&clk_ext_camera>; - clock-names = "xclk"; - - port { - /* Parallel bus endpoint */ - ov5640_to_parallel: endpoint { - remote-endpoint = <¶llel_from_ov5640>; - bus-width = <8>; - data-shift = <2>; /* lines 9:2 are used */ - hsync-active = <0>; - vsync-active = <0>; - pclk-sample = <1>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt deleted file mode 100644 index 72ad992f77be..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt +++ /dev/null @@ -1,54 +0,0 @@ -* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor - -The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with -an active array size of 2592H x 1944V. It is programmable through a serial I2C -interface. - -Required Properties: -- compatible: Value should be "ovti,ov5645". -- clocks: Reference to the xclk clock. -- clock-names: Should be "xclk". -- clock-frequency: Frequency of the xclk clock. -- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds - to the hardware pin PWDNB which is physically active low. -- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to - the hardware pin RESETB. -- vdddo-supply: Chip digital IO regulator. -- vdda-supply: Chip analog regulator. -- vddd-supply: Chip digital core regulator. - -The device node must contain one 'port' child node for its digital output -video port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: - - &i2c1 { - ... - - ov5645: ov5645@3c { - compatible = "ovti,ov5645"; - reg = <0x3c>; - - enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&camera_rear_default>; - - clocks = <&clks 200>; - clock-names = "xclk"; - clock-frequency = <24000000>; - - vdddo-supply = <&camera_dovdd_1v8>; - vdda-supply = <&camera_avdd_2v8>; - vddd-supply = <&camera_dvdd_1v2>; - - port { - ov5645_ep: endpoint { - clock-lanes = <1>; - data-lanes = <0 2>; - remote-endpoint = <&csi0_ep>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt deleted file mode 100644 index 22e44945b661..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov5647.txt +++ /dev/null @@ -1,35 +0,0 @@ -Omnivision OV5647 raw image sensor ---------------------------------- - -OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces -and CCI (I2C compatible) control bus. - -Required properties: - -- compatible : "ovti,ov5647". -- reg : I2C slave address of the sensor. -- clocks : Reference to the xclk clock. - -The common video interfaces bindings (see video-interfaces.txt) should be -used to specify link to the image data receiver. The OV5647 device -node should contain one 'port' child node with an 'endpoint' subnode. - -Endpoint node mandatory properties: - -- remote-endpoint: A phandle to the bus receiver's endpoint node. - -Example: - - i2c@2000 { - ... - ov: camera@36 { - compatible = "ovti,ov5647"; - reg = <0x36>; - clocks = <&camera_clk>; - port { - camera_1: endpoint { - remote-endpoint = <&csi1_ep1>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5695.txt b/Documentation/devicetree/bindings/media/i2c/ov5695.txt deleted file mode 100644 index 640a63717d96..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov5695.txt +++ /dev/null @@ -1,41 +0,0 @@ -* Omnivision OV5695 MIPI CSI-2 sensor - -Required Properties: -- compatible: shall be "ovti,ov5695" -- clocks: reference to the xvclk input clock -- clock-names: shall be "xvclk" -- avdd-supply: Analog voltage supply, 2.8 volts -- dovdd-supply: Digital I/O voltage supply, 1.8 volts -- dvdd-supply: Digital core voltage supply, 1.2 volts -- reset-gpios: Low active reset gpio - -The device node shall contain one 'port' child node with an -'endpoint' subnode for its digital output video port, -in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. -The endpoint optional property 'data-lanes' shall be "<1 2>". - -Example: -&i2c7 { - ov5695: camera-sensor@36 { - compatible = "ovti,ov5695"; - reg = <0x36>; - pinctrl-names = "default"; - pinctrl-0 = <&clk_24m_cam>; - - clocks = <&cru SCLK_TESTCLKOUT1>; - clock-names = "xvclk"; - - avdd-supply = <&pp2800_cam>; - dovdd-supply = <&pp1800>; - dvdd-supply = <&pp1250_cam>; - reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; - - port { - wcam_out: endpoint { - remote-endpoint = <&mipi_in_wcam>; - data-lanes = <1 2>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt deleted file mode 100644 index 8281151f7493..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov7251.txt +++ /dev/null @@ -1,52 +0,0 @@ -* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor - -The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor -with an active array size of 640H x 480V. It is programmable through a serial -I2C interface. - -Required Properties: -- compatible: Value should be "ovti,ov7251". -- clocks: Reference to the xclk clock. -- clock-names: Should be "xclk". -- clock-frequency: Frequency of the xclk clock. -- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds - to the hardware pin XSHUTDOWN which is physically active low. -- vdddo-supply: Chip digital IO regulator. -- vdda-supply: Chip analog regulator. -- vddd-supply: Chip digital core regulator. - -The device node shall contain one 'port' child node with a single 'endpoint' -subnode for its digital output video port, in accordance with the video -interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: - - &i2c1 { - ... - - ov7251: camera-sensor@60 { - compatible = "ovti,ov7251"; - reg = <0x60>; - - enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&camera_bw_default>; - - clocks = <&clks 200>; - clock-names = "xclk"; - clock-frequency = <24000000>; - - vdddo-supply = <&camera_dovdd_1v8>; - vdda-supply = <&camera_avdd_2v8>; - vddd-supply = <&camera_dvdd_1v2>; - - port { - ov7251_ep: endpoint { - clock-lanes = <1>; - data-lanes = <0>; - remote-endpoint = <&csi0_ep>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt deleted file mode 100644 index 0b3ede5b8e6a..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov772x.txt +++ /dev/null @@ -1,40 +0,0 @@ -* Omnivision OV7720/OV7725 CMOS sensor - -The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, -such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can -support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. - -Required Properties: -- compatible: shall be one of - "ovti,ov7720" - "ovti,ov7725" -- clocks: reference to the xclk input clock. - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the RSTB pin which is - active low, if any. -- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is - active high, if any. - -The device node shall contain one 'port' child node with one child 'endpoint' -subnode for its digital output video port, in accordance with the video -interface bindings defined in Documentation/devicetree/bindings/media/ -video-interfaces.txt. - -Example: - -&i2c0 { - ov772x: camera@21 { - compatible = "ovti,ov7725"; - reg = <0x21>; - reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; - powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; - clocks = <&xclk>; - - port { - ov772x_0: endpoint { - remote-endpoint = <&vcap1_in0>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov8856.yaml b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml new file mode 100644 index 000000000000..816dac9c6f60 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2019 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ov8856.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV8856 CMOS Sensor + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: |- + The Omnivision OV8856 is a high performance, 1/4-inch, 8 megapixel, CMOS + image sensor that delivers 3264x2448 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. This chip is programmable + through I2C and two-wire SCCB. The sensor output is available via CSI-2 + serial data output (up to 4-lane). + +properties: + compatible: + const: ovti,ov8856 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: + Input clock for the sensor. + items: + - const: xvclk + + clock-frequency: + description: + Frequency of the xvclk clock in Hertz. + + dovdd-supply: + description: + Definition of the regulator used as interface power supply. + + avdd-supply: + description: + Definition of the regulator used as analog power supply. + + dvdd-supply: + description: + Definition of the regulator used as digital power supply. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDOWN which is physically + active low. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - link-frequencies + +required: + - compatible + - reg + - clocks + - clock-names + - clock-frequency + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8856: camera@10 { + compatible = "ovti,ov8856"; + reg = <0x10>; + + reset-gpios = <&pio 111 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cam_osc>; + clock-names = "xvclk"; + clock-frequency = <19200000>; + + avdd-supply = <&mt6358_vcama2_reg>; + dvdd-supply = <&mt6358_vcamd_reg>; + dovdd-supply = <&mt6358_vcamio_reg>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml new file mode 100644 index 000000000000..67c1c291327b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml @@ -0,0 +1,148 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV02A10 CMOS Sensor + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel + image sensor, which is the latest production derived from Omnivision's CMOS + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The + sensor output is available via CSI-2 serial data output. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov02a10 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: + External clock for the sensor. + items: + - const: eclk + + clock-frequency: + description: + Frequency of the eclk clock in Hz. + + dovdd-supply: + description: + Definition of the regulator used as Digital I/O voltage supply. + + avdd-supply: + description: + Definition of the regulator used as Analog voltage supply. + + dvdd-supply: + description: + Definition of the regulator used as Digital core voltage supply. + + powerdown-gpios: + description: + Must be the device tree identifier of the GPIO connected to the + PD_PAD pin. This pin is used to place the OV02A10 into standby mode + or shutdown mode. As the line needs to be high for the powerdown mode + to be active, it should be marked GPIO_ACTIVE_HIGH. + maxItems: 1 + + reset-gpios: + description: + Must be the device tree identifier of the GPIO connected to the + RST_PD pin. If specified, it will be asserted during driver probe. + As the line needs to be low for the reset to be active, it should be + marked GPIO_ACTIVE_LOW. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + ovti,mipi-clock-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Definition of MIPI clock voltage unit. This entry corresponds to + the link speed defined by the 'link-frequencies' property. + If present, the value shall be in the range of 0-4. + default: 4 + + required: + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - clock-names + - clock-frequency + - dovdd-supply + - avdd-supply + - dvdd-supply + - powerdown-gpios + - reset-gpios + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov02a10: camera-sensor@3d { + compatible = "ovti,ov02a10"; + reg = <0x3d>; + + powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>; + + clocks = <&ov02a10_clk>; + clock-names = "eclk"; + clock-frequency = <24000000>; + + rotation = <180>; + + dovdd-supply = <&ov02a10_dovdd>; + avdd-supply = <&ov02a10_avdd>; + dvdd-supply = <&ov02a10_dvdd>; + + port { + wcam_out: endpoint { + link-frequencies = /bits/ 64 <390000000>; + ovti,mipi-clock-voltage = <3>; + remote-endpoint = <&mipi_in_wcam>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml new file mode 100644 index 000000000000..cf456f8d9ddc --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV2680 CMOS Sensor + +maintainers: + - Rui Miguel Silva <rmfrfs@gmail.com> + +description: |- + The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2 + megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200) + camera. It provides full-frame, sub-sampled, or windowed 10-bit images in + various formats via the control of the Serial Camera Control Bus (SCCB) + interface. The OV2680 has an image array capable of operating at up to 30 + frames per second (fps) in UXGA resolution. + +properties: + compatible: + const: ovti,ov2680 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: xvclk + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDOWN which is physically + active low. + maxItems: 1 + + dovdd-supply: + description: + Definition of the regulator used as interface power supply. + + avdd-supply: + description: + Definition of the regulator used as analog power supply. + + dvdd-supply: + description: + Definition of the regulator used as digital power supply. + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + A node containing an output port node. + +required: + - compatible + - reg + - clocks + - clock-names + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov2680: camera-sensor@36 { + compatible = "ovti,ov2680"; + reg = <0x36>; + clocks = <&osc>; + clock-names = "xvclk"; + reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + + dovdd-supply = <&sw2_reg>; + dvdd-supply = <&sw2_reg>; + avdd-supply = <®_peri_3p15v>; + + port { + ov2680_to_mipi: endpoint { + remote-endpoint = <&mipi_from_sensor>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml new file mode 100644 index 000000000000..e2ffe0a9c26b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2685.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV2685 Image Sensor + +maintainers: + - Shunqian Zheng <zhengsq@rock-chips.com> + +properties: + compatible: + const: ovti,ov2685 + + reg: + maxItems: 1 + + clocks: + items: + - description: XVCLK clock + + clock-names: + items: + - const: xvclk + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - clock-names + - dvdd-supply + - avdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov2685: camera-sensor@3c { + compatible = "ovti,ov2685"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cru SCLK_TESTCLKOUT1>; + clock-names = "xvclk"; + + avdd-supply = <&pp2800_cam>; + dovdd-supply = <&pp1800>; + dvdd-supply = <&pp1800>; + reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml new file mode 100644 index 000000000000..d96199031b66 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml @@ -0,0 +1,130 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov4689.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV4689 CMOS + +maintainers: + - Mikhail Rudenko <mike.rudenko@gmail.com> + +description: | + The Omnivision OV4689 is a high performance, 1/3-inch, 4 megapixel + image sensor. Ihis chip supports high frame rate speeds up to 90 fps + at 2688x1520 resolution. It is programmable through an I2C + interface, and sensor output is sent via 1/2/4 lane MIPI CSI-2 + connection. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov4689 + + reg: + maxItems: 1 + + clocks: + description: + External clock (XVCLK) for the sensor, 6-64 MHz + maxItems: 1 + + dovdd-supply: + description: + Digital I/O voltage supply, 1.7-3.0 V + + avdd-supply: + description: + Analog voltage supply, 2.6-3.0 V + + dvdd-supply: + description: + Digital core voltage supply, 1.1-1.3 V + + powerdown-gpios: + description: + GPIO connected to the powerdown pin (active low) + + reset-gpios: + maxItems: 1 + description: + GPIO connected to the reset pin (active low) + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - dovdd-supply + - avdd-supply + - dvdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov4689: camera@36 { + compatible = "ovti,ov4689"; + reg = <0x36>; + + clocks = <&ov4689_clk>; + + avdd-supply = <&ov4689_avdd>; + dovdd-supply = <&ov4689_dovdd>; + dvdd-supply = <&ov4689_dvdd>; + + powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>; + reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>; + + orientation = <2>; + rotation = <0>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <504000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml new file mode 100644 index 000000000000..2c5e69356658 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5640 Image Sensor + +maintainers: + - Steve Longerbeam <slongerbeam@gmail.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov5640 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-names: + const: xclk + + AVDD-supply: + description: Analog voltage supply, 2.8 volts + + DVDD-supply: + description: Digital core voltage supply, 1.5 volts + + DOVDD-supply: + description: Digital I/O voltage supply, 1.8 volts + + powerdown-gpios: + maxItems: 1 + description: > + Reference to the GPIO connected to the powerdown pin, if any. + + reset-gpios: + maxItems: 1 + description: > + Reference to the GPIO connected to the reset pin, if any. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + const: 0 + + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + bus-width: + enum: [8, 10] + + data-shift: + enum: [0, 2] + +required: + - compatible + - reg + - clocks + - clock-names + - AVDD-supply + - DVDD-supply + - DOVDD-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + rotation = <180>; + + port { + /* MIPI CSI-2 bus endpoint */ + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_from_ov5640>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5642.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5642.yaml new file mode 100644 index 000000000000..01f8b2b3fd17 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5642.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5642.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5642 Image Sensor + +maintainers: + - Fabio Estevam <festevam@gmail.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov5642 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + AVDD-supply: + description: Analog voltage supply, 2.8V. + + DVDD-supply: + description: Digital core voltage supply, 1.5V. + + DOVDD-supply: + description: Digital I/O voltage supply, 1.8V. + + powerdown-gpios: + maxItems: 1 + description: Reference to the GPIO connected to the powerdown pin, if any. + + reset-gpios: + maxItems: 1 + description: Reference to the GPIO connected to the reset pin, if any. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [5, 6] + + bus-width: + enum: [8, 10] + default: 10 + + data-shift: + enum: [0, 2] + default: 0 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + allOf: + - if: + properties: + bus-type: + const: 6 + then: + properties: + hsync-active: false + vsync-active: false + + - if: + properties: + bus-width: + const: 10 + then: + properties: + data-shift: + const: 0 + + required: + - bus-type + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5642"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5642>; + clocks = <&clk_ext_camera>; + DOVDD-supply = <&vgen4_reg>; + AVDD-supply = <&vgen3_reg>; + DVDD-supply = <&vgen2_reg>; + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + + port { + ov5642_to_parallel: endpoint { + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + remote-endpoint = <¶llel_from_ov5642>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml new file mode 100644 index 000000000000..bc9b27afe3ea --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5645.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5645 Image Sensor + +maintainers: + - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> + +properties: + compatible: + const: ovti,ov5645 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-frequency: + description: Frequency of the xclk clock in Hz. + + vdda-supply: + description: Analog voltage supply, 2.8 volts + + vddd-supply: + description: Digital core voltage supply, 1.5 volts + + vdddo-supply: + description: Digital I/O voltage supply, 1.8 volts + + enable-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the PWDNB pin, if any. + + reset-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the RESETB pin, if any. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - vdddo-supply + - vdda-supply + - vddd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5645"; + reg = <0x3c>; + clocks = <&clks 1>; + clock-frequency = <24000000>; + vdddo-supply = <&ov5645_vdddo_1v8>; + vdda-supply = <&ov5645_vdda_2v8>; + vddd-supply = <&ov5645_vddd_1v5>; + enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5645>; + + port { + ov5645_ep: endpoint { + remote-endpoint = <&csi0_ep>; + data-lanes = <1 2>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml new file mode 100644 index 000000000000..a2abed06a099 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5647.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5647 raw image sensor + +maintainers: + - Dave Stevenson <dave.stevenson@raspberrypi.com> + - Jacopo Mondi <jacopo@jmondi.org> + +description: |- + The OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data + interfaces and CCI (I2C compatible) control bus. + +properties: + compatible: + const: ovti,ov5647 + + reg: + description: I2C device address. + maxItems: 1 + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + pwdn-gpios: + description: Reference to the GPIO connected to the pwdn pin. Active high. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-noncontinuous: true + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5647: camera@36 { + compatible = "ovti,ov5647"; + reg = <0x36>; + clocks = <&camera_clk>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + port { + camera_out: endpoint { + remote-endpoint = <&csi1_ep1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml new file mode 100644 index 000000000000..1f497679168c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5648.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5648 Image Sensor + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + const: ovti,ov5648 + + reg: + maxItems: 1 + + clocks: + items: + - description: XVCLK Clock + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply (internal AVDD is used if missing) + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - assigned-clocks + - assigned-clock-rates + - dvdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sun8i-v3s-ccu.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5648: camera@36 { + compatible = "ovti,ov5648"; + reg = <0x36>; + + dvdd-supply = <&ov5648_dvdd>; + avdd-supply = <&ov5648_avdd>; + dovdd-supply = <&ov5648_dovdd>; + clocks = <&ov5648_xvclk 0>; + assigned-clocks = <&ov5648_xvclk 0>; + assigned-clock-rates = <24000000>; + + + ov5648_out: port { + ov5648_out_mipi_csi2: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <210000000 168000000>; + + remote-endpoint = <&mipi_csi2_in_ov5648>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5670.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5670.yaml new file mode 100644 index 000000000000..6e089fe1d613 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5670.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5670.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5670 5 Megapixels raw image sensor + +maintainers: + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + +description: |- + The OV5670 is a 5 Megapixels raw image sensor which provides images in 10-bits + RAW BGGR Bayer format on a 2 data lanes MIPI CSI-2 serial interface and is + controlled through an I2C compatible control bus. + +properties: + compatible: + const: ovti,ov5670 + + reg: + maxItems: 1 + + clocks: + description: System clock. From 6 to 27 MHz. + maxItems: 1 + + powerdown-gpios: + description: Reference to the GPIO connected to the PWDNB pin. Active low. + + reset-gpios: + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low. + maxItems: 1 + + avdd-supply: + description: Analog circuit power. Typically 2.8V. + + dvdd-supply: + description: Digital circuit power. Typically 1.2V. + + dovdd-supply: + description: Digital I/O circuit power. Typically 2.8V or 1.8V. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + clock-noncontinuous: true + remote-endpoint: true + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5670: sensor@36 { + compatible = "ovti,ov5670"; + reg = <0x36>; + + clocks = <&sensor_xclk>; + + port { + ov5670_ep: endpoint { + remote-endpoint = <&csi_ep>; + data-lanes = <1 2>; + clock-noncontinuous; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml new file mode 100644 index 000000000000..ad07204057f9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5675.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5675 CMOS Sensor + +maintainers: + - Quentin Schulz <quentin.schulz@theobroma-systems.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +description: | + The Omnivision OV5675 is a high performance, 1/5-inch, 5 megapixel, CMOS + image sensor that delivers 2592x1944 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. + + This chip is programmable through I2C and two-wire SCCB. The sensor output + is available via CSI-2 serial data output (up to 2-lane). + +properties: + compatible: + const: ovti,ov5675 + + reg: + maxItems: 1 + + clocks: + description: + System input clock (aka XVCLK). From 6 to 27 MHz. + maxItems: 1 + + dovdd-supply: + description: + Digital I/O voltage supply, 1.8 volts. + + avdd-supply: + description: + Analog voltage supply, 2.8 volts. + + dvdd-supply: + description: + Digital core voltage supply, 1.2 volts. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDN which is physically + active low. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + + # Supports max data transfer of 900 Mbps per lane + link-frequencies: true + +required: + - compatible + - reg + - clocks + - dovdd-supply + - avdd-supply + - dvdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/px30-cru.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/pinctrl/rockchip.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5675: camera@36 { + compatible = "ovti,ov5675"; + reg = <0x36>; + + reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cif_clkout_m0>; + + clocks = <&cru SCLK_CIF_OUT>; + assigned-clocks = <&cru SCLK_CIF_OUT>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vcc_1v8>; + dvdd-supply = <&vcc_1v2>; + dovdd-supply = <&vcc_2v8>; + + rotation = <90>; + orientation = <0>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <450000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml new file mode 100644 index 000000000000..3368b3bd8ef2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2022 Amarulasolutions +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5693/OV5695 CMOS Sensors + +maintainers: + - Tommaso Merciai <tomm.merciai@gmail.com> + +description: | + The Omnivision OV5693/OV5695 are high performance, 1/4-inch, 5 megapixel, CMOS + image sensors that deliver 2592x1944 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. + + OV5693/OV5695 are controlled via I2C and two-wire Serial Camera Control Bus + (SCCB). The sensor output is available via CSI-2 serial data output (up to + 2-lane). + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + - if: + properties: + compatible: + contains: + const: ovti,ov5693 + then: + properties: + port: + properties: + endpoint: + required: + - link-frequencies + +properties: + compatible: + enum: + - ovti,ov5693 + - ovti,ov5695 + + reg: + maxItems: 1 + + clocks: + description: + System input clock (aka XVCLK). From 6 to 27 MHz. + maxItems: 1 + + clock-names: + const: xvclk + + dovdd-supply: + description: + Digital I/O voltage supply, 1.8V. + + avdd-supply: + description: + Analog voltage supply, 2.8V. + + dvdd-supply: + description: + Digital core voltage supply, 1.2V. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDN which is physically + active low. + maxItems: 1 + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/px30-cru.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/pinctrl/rockchip.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5693: camera@36 { + compatible = "ovti,ov5693"; + reg = <0x36>; + + reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cif_clkout_m0>; + + clocks = <&cru SCLK_CIF_OUT>; + assigned-clocks = <&cru SCLK_CIF_OUT>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vcc_1v8>; + dvdd-supply = <&vcc_1v2>; + dovdd-supply = <&vcc_2v8>; + + rotation = <90>; + orientation = <0>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <450000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml new file mode 100644 index 000000000000..2b6143aff391 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov64a40.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV64A40 Image Sensor + +maintainers: + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov64a40 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + avdd-supply: + description: Analog voltage supply, 2.8 volts + + dvdd-supply: + description: Digital core voltage supply, 1.1 volts + + dovdd-supply: + description: Digital I/O voltage supply, 1.8 volts + + powerdown-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + bus-type: + enum: + - 1 # MIPI CSI-2 C-PHY + - 4 # MIPI CSI-2 D-PHY + data-lanes: true + link-frequencies: true + clock-noncontinuous: true + remote-endpoint: true + + required: + - bus-type + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@36 { + compatible = "ovti,ov64a40"; + reg = <0x36>; + clocks = <&camera_clk>; + dovdd-supply = <&vgen4_reg>; + avdd-supply = <&vgen3_reg>; + dvdd-supply = <&vgen2_reg>; + powerdown-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + rotation = <180>; + orientation = <2>; + + port { + endpoint { + remote-endpoint = <&mipi_csi2_in>; + bus-type = <4>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <456000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml new file mode 100644 index 000000000000..2e5187acbbb8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov7251.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV7251 Image Sensor + +description: + The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor + with an active array size of 640H x 480V. It is programmable through a serial + I2C interface. + +maintainers: + - Todor Tomov <todor.too@gmail.com> + +properties: + compatible: + const: ovti,ov7251 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-names: + const: xclk + + clock-frequency: + description: Frequency of the xclk clock in Hz. + + vdda-supply: + description: Analog voltage supply, 2.8 volts + + vddd-supply: + description: Digital core voltage supply, 1.2 volts + + vdddo-supply: + description: Digital I/O voltage supply, 1.8 volts + + enable-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the XSHUTDOWN pin, if any. Polarity + is GPIO_ACTIVE_HIGH. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maximum: 1 + + data-lanes: + maxItems: 1 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - vdddo-supply + - vdda-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov7251"; + reg = <0x3c>; + clocks = <&clks 1>; + clock-frequency = <24000000>; + vdddo-supply = <&ov7251_vdddo_1v8>; + vdda-supply = <&ov7251_vdda_2v8>; + vddd-supply = <&ov7251_vddd_1v5>; + enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + + port { + ov7251_ep: endpoint { + remote-endpoint = <&csi0_ep>; + clock-lanes = <1>; + data-lanes = <0>; + link-frequencies = /bits/ 64 <240000000 319200000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml new file mode 100644 index 000000000000..5d24edba8f99 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov772x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV7720/OV7725 CMOS sensor + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + +description: | + The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, + such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can + support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. + +properties: + compatible: + enum: + - ovti,ov7720 + - ovti,ov7725 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + reset-gpios: + description: | + Reference to the GPIO connected to the RSTB pin which is active low. + maxItems: 1 + + powerdown-gpios: + description: | + Reference to the GPIO connected to the PWDN pin which is active high. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [5, 6] + + bus-width: + enum: [8, 10] + default: 10 + + data-shift: + enum: [0, 2] + default: 0 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + allOf: + - if: + properties: + bus-type: + const: 6 + then: + properties: + hsync-active: false + vsync-active: false + + - if: + properties: + bus-width: + const: 10 + then: + properties: + data-shift: + const: 0 + + required: + - bus-type + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + ov772x: camera@21 { + compatible = "ovti,ov7725"; + reg = <0x21>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; + clocks = <&xclk>; + + port { + ov772x_0: endpoint { + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + vsync-active = <0>; + hsync-active = <0>; + pclk-sample = <0>; + bus-width = <8>; + data-shift = <0>; + remote-endpoint = <&vcap1_in0>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml new file mode 100644 index 000000000000..a65f921ec0fd --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8858.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8858 Image Sensor + +maintainers: + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + - Nicholas Roth <nicholas@rothemail.net> + +description: | + The OmniVision OV8858 is a color CMOS 8 Megapixels (3264x2448) image sensor + controlled through an I2C-compatible SCCB bus. The sensor transmits images + on a MIPI CSI-2 output interface with up to 4 data lanes. + +properties: + compatible: + const: ovti,ov8858 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: XVCLK external clock + + clock-names: + const: xvclk + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + description: PWDNB powerdown GPIO (active low) + + reset-gpios: + maxItems: 1 + description: XSHUTDN reset GPIO (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/pinctrl/rockchip.h> + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8858: camera@36 { + compatible = "ovti,ov8858"; + reg = <0x36>; + + clocks = <&cru SCLK_CIF_OUT>; + clock-names = "xvclk"; + assigned-clocks = <&cru SCLK_CIF_OUT>; + assigned-clock-rates = <24000000>; + + dovdd-supply = <&vcc1v8_dvp>; + + reset-gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&gpio2 RK_PB4 GPIO_ACTIVE_LOW>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1 2 3 4>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file mode 100644 index 000000000000..8a70e23ba6ab --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8865.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8865 Image Sensor + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + const: ovti,ov8865 + + reg: + maxItems: 1 + + clocks: + items: + - description: EXTCLK Clock + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - assigned-clocks + - assigned-clock-rates + - dvdd-supply + - avdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sun8i-a83t-ccu.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml new file mode 100644 index 000000000000..79a7658f6d05 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov9282.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV9282 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + OV9282 sensor is an OmniVision black & white CMOS active pixel digital image + sensor with an active array size of 1296H x 816V. It is programmable through + I2C interface. The I2C client address is fixed to 0x60/0x70 as per sensor data + sheet. Image data is sent through MIPI CSI-2. + OV9281 has a different lens chief ray angle. + +properties: + compatible: + enum: + - ovti,ov9281 + - ovti,ov9282 + reg: + description: I2C address + maxItems: 1 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: Clock frequency from 6 to 27MHz + maxItems: 1 + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + maxItems: 1 + + avdd-supply: + description: Analog voltage supply, 2.8 volts + + dvdd-supply: + description: Digital core voltage supply, 1.2 volts + + dovdd-supply: + description: Digital I/O voltage supply, 1.8 volts + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@60 { + compatible = "ovti,ov9282"; + reg = <0x60>; + clocks = <&ov9282_clk>; + + assigned-clocks = <&ov9282_clk>; + assigned-clock-parents = <&ov9282_clk_parent>; + assigned-clock-rates = <24000000>; + + port { + ov9282: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <800000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml new file mode 100644 index 000000000000..34a05df786ce --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/rda,rda5807.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Unisoc Communications RDA5807 FM radio receiver + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +properties: + compatible: + enum: + - rda,rda5807 + + reg: + description: I2C address. + maxItems: 1 + + power-supply: true + + rda,lnan: + description: Use LNAN input port. + type: boolean + + rda,lnap: + description: Use LNAP input port. + type: boolean + + rda,analog-out: + description: Enable analog audio output. + type: boolean + + rda,i2s-out: + description: Enable I2S digital audio output. + type: boolean + + rda,lna-microamp: + description: LNA working current, in micro-amperes. + default: 2500 + enum: [1800, 2100, 2500, 3000] + +required: + - compatible + - reg + - power-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + radio@11 { + compatible = "rda,rda5807"; + reg = <0x11>; + + power-supply = <&ldo6>; + + rda,lnan; + rda,lnap; + rda,analog-out; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/samsung,s5k5baf.yaml b/Documentation/devicetree/bindings/media/i2c/samsung,s5k5baf.yaml new file mode 100644 index 000000000000..c8f2955e0825 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/samsung,s5k5baf.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/samsung,s5k5baf.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + +properties: + compatible: + const: samsung,s5k5baf + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mclk + + clock-frequency: + default: 24000000 + description: mclk clock frequency + + rstn-gpios: + maxItems: 1 + description: RSTN pin + + stbyn-gpios: + maxItems: 1 + description: STDBYN pin + + vdda-supply: + description: Analog power supply 2.8V (2.6V to 3.0V) + + vddio-supply: + description: I/O power supply 1.8V (1.65V to 1.95V) or 2.8V (2.5V to 3.1V) + + vddreg-supply: + description: + Regulator input power supply 1.8V (1.7V to 1.9V) or 2.8V (2.6V to 3.0) + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + +required: + - compatible + - clocks + - clock-names + - rstn-gpios + - stbyn-gpios + - vdda-supply + - vddio-supply + - vddreg-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@2d { + compatible = "samsung,s5k5baf"; + reg = <0x2d>; + clocks = <&camera 0>; + clock-names = "mclk"; + clock-frequency = <24000000>; + rstn-gpios = <&gpl2 1 GPIO_ACTIVE_LOW>; + stbyn-gpios = <&gpl2 0 GPIO_ACTIVE_LOW>; + vdda-supply = <&cam_io_en_reg>; + vddio-supply = <&vtcam_reg>; + vddreg-supply = <&vt_core_15v_reg>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/samsung,s5k6a3.yaml b/Documentation/devicetree/bindings/media/i2c/samsung,s5k6a3.yaml new file mode 100644 index 000000000000..7e83a94124b5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/samsung,s5k6a3.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/samsung,s5k6a3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5K6A3(YX) raw image sensor + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + +description: + S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data + interfaces and CCI (I2C compatible) control bus. + +properties: + compatible: + const: samsung,s5k6a3 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: extclk + + clock-frequency: + default: 24000000 + description: extclk clock frequency + + gpios: + maxItems: 1 + description: GPIO connected to the RESET pin + + afvdd-supply: + description: AF (actuator) voltage supply + + svdda-supply: + description: Core voltage supply + + svddio-supply: + description: I/O voltage supply + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + +required: + - compatible + - clocks + - clock-names + - gpios + - afvdd-supply + - svdda-supply + - svddio-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@10 { + compatible = "samsung,s5k6a3"; + reg = <0x10>; + clock-frequency = <24000000>; + clocks = <&camera 1>; + clock-names = "extclk"; + gpios = <&gpm1 6 GPIO_ACTIVE_LOW>; + afvdd-supply = <&ldo19_reg>; + svdda-supply = <&cam_io_reg>; + svddio-supply = <&ldo19_reg>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt b/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt deleted file mode 100644 index f11f28a5fda4..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt +++ /dev/null @@ -1,53 +0,0 @@ -* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor - -The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with -an active array size of 4224H x 3200V. It is programmable through an I2C -interface. -Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum -throughput of 1.2Gbps/lane. - - -Required Properties: -- compatible: Shall be "sony,imx214". -- reg: I2C bus address of the device. Depending on how the sensor is wired, - it shall be <0x10> or <0x1a>; -- enable-gpios: GPIO descriptor for the enable pin. -- vdddo-supply: Chip digital IO regulator (1.8V). -- vdda-supply: Chip analog regulator (2.7V). -- vddd-supply: Chip digital core regulator (1.12V). -- clocks: Reference to the xclk clock. -- clock-frequency: Frequency of the xclk clock. - -Optional Properties: -- flash-leds: See ../video-interfaces.txt -- lens-focus: See ../video-interfaces.txt - -The imx214 device node shall contain one 'port' child node with -an 'endpoint' subnode. For further reading on port node refer to -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Required Properties on endpoint: -- data-lanes: check ../video-interfaces.txt -- link-frequencies: check ../video-interfaces.txt -- remote-endpoint: check ../video-interfaces.txt - -Example: - - camera-sensor@1a { - compatible = "sony,imx214"; - reg = <0x1a>; - vdddo-supply = <&pm8994_lvs1>; - vddd-supply = <&camera_vddd_1v12>; - vdda-supply = <&pm8994_l17>; - lens-focus = <&ad5820>; - enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; - clocks = <&mmcc CAMSS_MCLK0_CLK>; - clock-frequency = <24000000>; - port { - imx214_ep: endpoint { - data-lanes = <1 2 3 4>; - link-frequencies = /bits/ 64 <480000000>; - remote-endpoint = <&csiphy0_ep>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml new file mode 100644 index 000000000000..60903da84e1f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml @@ -0,0 +1,125 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx214.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/3.06-Inch 13.13MP CMOS Digital Image Sensor + +maintainers: + - Ricardo Ribalda <ribalda@kernel.org> + +description: | + The Sony IMX214 is a 1/3.06-inch CMOS active pixel digital image sensor with + an active array size of 4224H x 3200V. It is programmable through an I2C + interface. Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a + maximum throughput of 1.2Gbps/lane. + +allOf: + - $ref: ../video-interface-devices.yaml# + +properties: + compatible: + const: sony,imx214 + + reg: + enum: + - 0x10 + - 0x1a + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + clock-frequency: + description: Frequency of the xclk clock in Hz. + + enable-gpios: + description: GPIO descriptor for the enable pin. + maxItems: 1 + + vdddo-supply: + description: Chip digital IO regulator (1.8V). + + vdda-supply: + description: Chip analog regulator (2.7V). + + vddd-supply: + description: Chip digital core regulator (1.12V). + + flash-leds: true + lens-focus: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + anyOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-frequency + - enable-gpios + - vdddo-supply + - vdda-supply + - vddd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@1a { + compatible = "sony,imx214"; + reg = <0x1a>; + vdddo-supply = <&pm8994_lvs1>; + vddd-supply = <&camera_vddd_1v12>; + vdda-supply = <&pm8994_l17>; + lens-focus = <&ad5820>; + enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + clock-frequency = <24000000>; + + port { + imx214_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <480000000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml new file mode 100644 index 000000000000..b397a730ee94 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx274.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/2.5-Inch 8.51MP CMOS Digital Image Sensor + +maintainers: + - Leon Luo <leonl@leopardimaging.com> + +description: | + The Sony IMX274 is a 1/2.5-inch CMOS active pixel digital image sensor with an + active array size of 3864H x 2202V. It is programmable through I2C interface. + Image data is sent through MIPI CSI-2, which is configured as 4 lanes at 1440 + Mbps. + +properties: + compatible: + const: sony,imx274 + + reg: + const: 0x1a + + reset-gpios: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: inck + + vana-supply: + description: Sensor 2.8 V analog supply. + + vdig-supply: + description: Sensor 1.8 V digital core supply. + + vddl-supply: + description: Sensor digital IO 1.2 V supply. + + port: + $ref: /schemas/graph.yaml#/properties/port + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx274: camera-sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + reset-gpios = <&gpio_sensor 0 0>; + + port { + sensor_out: endpoint { + remote-endpoint = <&csiss_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml new file mode 100644 index 000000000000..a531badc16c9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx290.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX290 1/2.8-Inch CMOS Image Sensor + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with Square + Pixel, available in either mono or colour variants. It is programmable + through I2C and 4-wire interfaces. + + The sensor output is available via CMOS logic parallel SDR output, Low voltage + LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the default. + No bindings have been defined for the other busses. + + imx290lqr is the full model identifier for the colour variant. "sony,imx290" + is treated the same as this as it was the original compatible string. + imx290llr is the mono version of the sensor. + +properties: + compatible: + oneOf: + - enum: + - sony,imx290lqr # Colour + - sony,imx290llr # Monochrome + - sony,imx327lqr # Colour + - const: sony,imx290 + deprecated: true + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: Input clock (37.125 MHz or 74.25 MHz) + items: + - const: xclk + + clock-frequency: + description: Frequency of the xclk clock in Hz + + vdda-supply: + description: Analog power supply (2.9V) + + vddd-supply: + description: Digital core power supply (1.2V) + + vdddo-supply: + description: Digital I/O power supply (1.8V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + anyOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - clock-frequency + - vdda-supply + - vddd-supply + - vdddo-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx290: camera-sensor@1a { + compatible = "sony,imx290lqr"; + reg = <0x1a>; + + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc 90>; + clock-names = "xclk"; + clock-frequency = <37125000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + + port { + imx290_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <445500000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx296.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx296.yaml new file mode 100644 index 000000000000..65ad9c100e45 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx296.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx296.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX296 1/2.8-Inch CMOS Image Sensor + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The Sony IMX296 is a 1/2.9-Inch active pixel type CMOS Solid-state image + sensor with square pixel array and 1.58 M effective pixels. This chip + features a global shutter with variable charge-integration time. It is + programmable through I2C and 4-wire interfaces. The sensor output is + available via CSI-2 serial data output (1 Lane). + +properties: + compatible: + enum: + - sony,imx296 + - sony,imx296ll + - sony,imx296lq + description: + The IMX296 sensor exists in two different models, a colour variant + (IMX296LQ) and a monochrome variant (IMX296LL). The device exposes the + model through registers, allowing for auto-detection with a common + "sony,imx296" compatible string. However, some camera modules disable the + ability to read the sensor model register, which disables this feature. + In those cases, the exact model needs to be specified as "sony,imx296ll" + or "sony,imx296lq". + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: Input clock (37.125 MHz, 54 MHz or 74.25 MHz) + items: + - const: inck + + avdd-supply: + description: Analog power supply (3.3V) + + dvdd-supply: + description: Digital power supply (1.2V) + + ovdd-supply: + description: Interface power supply (1.8V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + +required: + - compatible + - reg + - clocks + - clock-names + - avdd-supply + - dvdd-supply + - ovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx296: camera-sensor@1a { + compatible = "sony,imx296"; + reg = <0x1a>; + + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc 90>; + clock-names = "inck"; + + avdd-supply = <&camera_vdda_3v3>; + dvdd-supply = <&camera_vddd_1v2>; + ovdd-supply = <&camera_vddo_1v8>; + + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + + port { + imx296_ep: endpoint { + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml new file mode 100644 index 000000000000..bce57b22f7b6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx334.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX334 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + IMX334 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 3864H x 2202V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + const: sony,imx334 + reg: + description: I2C address + maxItems: 1 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: Clock frequency from 6 to 27 MHz, 37.125MHz, 74.25MHz + maxItems: 1 + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx334"; + reg = <0x1a>; + clocks = <&imx334_clk>; + + assigned-clocks = <&imx334_clk>; + assigned-clock-parents = <&imx334_clk_parent>; + assigned-clock-rates = <24000000>; + + port { + imx334: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <891000000 445500000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml new file mode 100644 index 000000000000..106c36ee966d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx335.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX335 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + IMX335 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 2592H x 1944V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + const: sony,imx335 + reg: + description: I2C address + maxItems: 1 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: Clock frequency from 6 to 27 MHz, 37.125MHz, 74.25MHz + maxItems: 1 + + avdd-supply: + description: Analog power supply (2.9V) + + ovdd-supply: + description: Interface power supply (1.8V) + + dvdd-supply: + description: Digital power supply (1.2V) + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + maxItems: 1 + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx335"; + reg = <0x1a>; + clocks = <&imx335_clk>; + + assigned-clocks = <&imx335_clk>; + assigned-clock-parents = <&imx335_clk_parent>; + assigned-clock-rates = <24000000>; + + avdd-supply = <&camera_vdda_2v9>; + ovdd-supply = <&camera_vddo_1v8>; + dvdd-supply = <&camera_vddd_1v2>; + + port { + imx335: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <594000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml new file mode 100644 index 000000000000..d9b7815650fd --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx412.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX412 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + IMX412 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 4072H x 3176V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + enum: + - sony,imx412 + - sony,imx577 + reg: + description: I2C address + maxItems: 1 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: Clock frequency 6MHz, 12MHz, 18MHz, 24MHz or 27MHz + maxItems: 1 + + dovdd-supply: + description: Interface power supply. + + avdd-supply: + description: Analog power supply. + + dvdd-supply: + description: Digital power supply. + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + maxItems: 1 + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx412"; + reg = <0x1a>; + clocks = <&imx412_clk>; + + assigned-clocks = <&imx412_clk>; + assigned-clock-parents = <&imx412_clk_parent>; + assigned-clock-rates = <24000000>; + + port { + imx412: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <600000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx415.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx415.yaml new file mode 100644 index 000000000000..9a00dab2e8a3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx415.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx415.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX415 CMOS Image Sensor + +maintainers: + - Michael Riesch <michael.riesch@wolfvision.net> + +description: |- + The Sony IMX415 is a diagonal 6.4 mm (Type 1/2.8) CMOS active pixel type + solid-state image sensor with a square pixel array and 8.46 M effective + pixels. This chip operates with analog 2.9 V, digital 1.1 V, and interface + 1.8 V triple power supply, and has low power consumption. + The IMX415 is programmable through I2C interface. The sensor output is + available via CSI-2 serial data output (two or four lanes). + +allOf: + - $ref: ../video-interface-devices.yaml# + +properties: + compatible: + const: sony,imx415 + + reg: + maxItems: 1 + + clocks: + description: Input clock (24 MHz, 27 MHz, 37.125 MHz, 72 MHz or 74.25 MHz) + maxItems: 1 + + avdd-supply: + description: Analog power supply (2.9 V) + + dvdd-supply: + description: Digital power supply (1.1 V) + + ovdd-supply: + description: Interface power supply (1.8 V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - avdd-supply + - dvdd-supply + - ovdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx415: camera-sensor@1a { + compatible = "sony,imx415"; + reg = <0x1a>; + avdd-supply = <&vcc2v9_cam>; + clocks = <&clock_cam>; + dvdd-supply = <&vcc1v1_cam>; + lens-focus = <&vcm>; + orientation = <2>; + ovdd-supply = <&vcc1v8_cam>; + reset-gpios = <&gpio_expander 14 GPIO_ACTIVE_LOW>; + rotation = <180>; + + port { + imx415_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <445500000>; + remote-endpoint = <&mipi_in>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt deleted file mode 100644 index 7976e6c40a80..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt +++ /dev/null @@ -1,82 +0,0 @@ -STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge - -MIPID02 has two CSI-2 input ports, only one of those ports can be active at a -time. Active port input stream will be de-serialized and its content outputted -through PARALLEL output port. -CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second -input port is a single lane 800Mbps. Both ports support clock and data lane -polarity swap. First port also supports data lane swap. -PARALLEL output port has a maximum width of 12 bits. -Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444, -YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. - -Required Properties: -- compatible: shall be "st,st-mipid02" -- clocks: reference to the xclk input clock. -- clock-names: shall be "xclk". -- VDDE-supply: sensor digital IO supply. Must be 1.8 volts. -- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts. - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the xsdn pin, if any. - This is an active low signal to the mipid02. - -Required subnodes: - - ports: A ports node with one port child node per device input and output - port, in accordance with the video interface bindings defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. The - port nodes are numbered as follows: - - Port Description - ----------------------------- - 0 CSI-2 first input port - 1 CSI-2 second input port - 2 PARALLEL output - -Endpoint node required property for CSI-2 connection is: -- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be -<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>. -Endpoint node optional property for CSI-2 connection is: -- lane-polarities: any lane can be inverted or not. - -Endpoint node required property for PARALLEL connection is: -- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>. -Endpoint node optional properties for PARALLEL connection are: -- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. -LOW being the default. -- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. -LOW being the default. - -Example: - -mipid02: csi2rx@14 { - compatible = "st,st-mipid02"; - reg = <0x14>; - status = "okay"; - clocks = <&clk_ext_camera_12>; - clock-names = "xclk"; - VDDE-supply = <&vdd>; - VDDIN-supply = <&vdd>; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - - ep0: endpoint { - data-lanes = <1 2>; - remote-endpoint = <&mipi_csi2_in>; - }; - }; - port@2 { - reg = <2>; - - ep2: endpoint { - bus-width = <8>; - hsync-active = <0>; - vsync-active = <0>; - remote-endpoint = <¶llel_out>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml new file mode 100644 index 000000000000..b68141264c0e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,st-mipid02.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: + MIPID02 has two CSI-2 input ports, only one of those ports can be + active at a time. Active port input stream will be de-serialized + and its content outputted through PARALLEL output port. + CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 + second input port is a single lane 800Mbps. Both ports support clock + and data lane polarity swap. First port also supports data lane swap. + PARALLEL output port has a maximum width of 12 bits. + Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, + RGB444, YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. + +properties: + compatible: + const: st,st-mipid02 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: xclk + + VDDE-supply: + description: + Sensor digital IO supply. Must be 1.8 volts. + + VDDIN-supply: + description: + Sensor internal regulator supply. Must be 1.8 volts. + + reset-gpios: + description: + Reference to the GPIO connected to the xsdn pin, if any. + This is an active low signal to the mipid02. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 first input port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Single-lane operation shall be <1> or <2> . + Dual-lane operation shall be <1 2> or <2 1> . + minItems: 1 + maxItems: 2 + + lane-polarities: + description: + Any lane can be inverted or not. + minItems: 1 + maxItems: 2 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 second input port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Single-lane operation shall be <1> or <2> . + maxItems: 1 + + lane-polarities: + description: + Any lane can be inverted or not. + maxItems: 1 + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: + enum: [6, 7, 8, 10, 12] + + required: + - bus-width + + anyOf: + - required: + - port@0 + - required: + - port@1 + + required: + - port@2 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - VDDE-supply + - VDDIN-supply + - ports + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + mipid02: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + clocks = <&clk_ext_camera_12>; + clock-names = "xclk"; + VDDE-supply = <&vdd>; + VDDIN-supply = <&vdd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + ep0: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&mipi_csi2_in>; + }; + }; + port@2 { + reg = <2>; + + ep2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + remote-endpoint = <¶llel_out>; + }; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml new file mode 100644 index 000000000000..8c28848b226a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2022 STMicroelectronics SA. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,st-vgxy61.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics VGxy61 HDR Global Shutter Sensor Family + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: |- + STMicroelectronics VGxy61 family has a CSI-2 output port. CSI-2 output is a + quad lanes 800Mbps per lane. + Supported formats are RAW8, RAW10, RAW12, RAW14 and RAW16. + Following part number are supported + - VG5661 and VG6661 are 1.6 Mpx (1464 x 1104) monochrome and color sensors. + Maximum frame rate is 75 fps. + - VG5761 and VG6761 are 2.3 Mpx (1944 x 1204) monochrome and color sensors. + Maximum frame rate is 60 fps. + +properties: + compatible: + const: st,st-vgxy61 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + VCORE-supply: + description: + Sensor digital core supply. Must be 1.2 volts. + + VDDIO-supply: + description: + Sensor digital IO supply. Must be 1.8 volts. + + VANA-supply: + description: + Sensor analog supply. Must be 2.8 volts. + + reset-gpios: + description: + Reference to the GPIO connected to the reset pin, if any. + This is an active low signal to the vgxy61. + + st,strobe-gpios-polarity: + description: + Invert polarity of illuminator's lights strobe GPIOs. + These GPIOs directly drive the illuminator LEDs. + type: boolean + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + CSI lanes to use + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + remote-endpoint: true + + required: + - data-lanes + +required: + - compatible + - clocks + - VCORE-supply + - VDDIO-supply + - VANA-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + vgxy61: csi2tx@10 { + compatible = "st,st-vgxy61"; + reg = <0x10>; + clocks = <&clk_ext_camera>; + VCORE-supply = <&v1v2>; + VDDIO-supply = <&v1v8>; + VANA-supply = <&v2v8>; + reset-gpios = <&mfxgpio 18 GPIO_ACTIVE_LOW>; + port { + ep0: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mipi_csi2_out>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/techwell,tw9900.yaml b/Documentation/devicetree/bindings/media/i2c/techwell,tw9900.yaml new file mode 100644 index 000000000000..e37317f81072 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/techwell,tw9900.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/techwell,tw9900.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Techwell TW9900 NTSC/PAL video decoder + +maintainers: + - Mehdi Djait <mehdi.djait@bootlin.com> + +description: + The tw9900 is a multi-standard video decoder, supporting NTSC, PAL standards + with auto-detection features. + +properties: + compatible: + const: techwell,tw9900 + + reg: + maxItems: 1 + + vdd-supply: + description: VDD power supply + + reset-gpios: + description: GPIO descriptor for the RESET input pin + maxItems: 1 + + powerdown-gpios: + description: GPIO descriptor for the POWERDOWN input pin + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + description: Analog input port + + properties: + endpoint@0: + $ref: /schemas/graph.yaml#/properties/endpoint + description: CVBS over MUX0 + + endpoint@1: + $ref: /schemas/graph.yaml#/properties/endpoint + description: CVBS over MUX1 + + endpoint@2: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Chroma over CIN0 and Y over MUX0 + + endpoint@3: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Chroma over CIN0 and Y over MUX1 + + oneOf: + - required: + - endpoint@0 + - required: + - endpoint@1 + - required: + - endpoint@2 + - required: + - endpoint@3 + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Video port for the decoder output. + + + required: + - port@0 + - port@1 + +required: + - compatible + - ports + - reg + - vdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/display/sdtv-standards.h> + #include <dt-bindings/gpio/gpio.h> + + composite_connector { + compatible = "composite-video-connector"; + label = "tv"; + sdtv-standards = <(SDTV_STD_PAL | SDTV_STD_NTSC)>; + + port { + composite_to_tw9900: endpoint { + remote-endpoint = <&tw9900_to_composite>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + video-decoder@44 { + compatible = "techwell,tw9900"; + reg = <0x44>; + + vdd-supply = <&tw9900_supply>; + reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + tw9900_to_composite: endpoint@0 { + reg = <0>; + remote-endpoint = <&composite_to_tw9900>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&cif_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml new file mode 100644 index 000000000000..1978fbb77a6c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml @@ -0,0 +1,224 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2023 Ideas on Board +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/thine,thp7312.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: THine THP7312 + +maintainers: + - Paul Elder <paul.elder@@ideasonboard.com> + +description: + The THP7312 is a standalone ISP controlled over i2c, and is capable of + various image processing and correction functions, including 3A control. It + can be connected to CMOS image sensors from various vendors, supporting both + MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2 + or parallel. The hardware is capable of transmitting and receiving MIPI + interlaved data strams with data types or multiple virtual channel + identifiers. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: thine,thp7312 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: CLKI clock input + + thine,boot-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1 + default: 1 + description: + Boot mode of the THP7312, reflecting the value of the BOOT[0] pin strap. + 0 is for the SPI/2-wire slave boot, 1 is for the SPI master boot (from + external flash ROM). + + reset-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the RESET_N pin, if any. + Must be released (set high) after all supplies are applied. + + vddcore-supply: + description: + 1.2V supply for core, PLL, MIPI rx and MIPI tx. + + vhtermrx-supply: + description: + Supply for input (RX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel. + + vddtx-supply: + description: + Supply for output (TX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel. + + vddhost-supply: + description: + Supply for host interface. 1.8V, 2.8V, or 3.3V. + + vddcmos-supply: + description: + Supply for sensor interface. 1.8V, 2.8V, or 3.3V. + + vddgpio-0-supply: + description: + Supply for GPIO_0. 1.8V, 2.8V, or 3.3V. + + vddgpio-1-supply: + description: + Supply for GPIO_1. 1.8V, 2.8V, or 3.3V. + + orientation: true + rotation: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + const: 4 # CSI-2 D-PHY + + data-lanes: + description: + This property is for lane reordering between the THP7312 and the + SoC. The sensor supports either two-lane, or four-lane operation. + If this property is omitted four-lane operation is assumed. For + two-lane operation the property must be set to <1 2>. + minItems: 2 + maxItems: 4 + items: + maximum: 4 + + sensors: + type: object + description: List of connected sensors + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + patternProperties: + "^sensor@[01]$": + type: object + description: + Sensors connected to the first and second input, with one node per + sensor. + + properties: + thine,model: + $ref: /schemas/types.yaml#/definitions/string + description: + Model of the connected sensors. Must be a valid compatible string. + + reg: + description: THP7312 input port number + items: + - maximum: 1 + + data-lanes: + $ref: /schemas/media/video-interfaces.yaml#/properties/data-lanes + items: + maxItems: 4 + description: + This property is for lane reordering between the THP7312 and the imaging + sensor that it is connected to. + + required: + - reg + - data-lanes + + additionalProperties: false + + required: + - "#address-cells" + - "#size-cells" + + additionalProperties: false + +required: + - compatible + - reg + - reset-gpios + - clocks + - vddcore-supply + - vhtermrx-supply + - vddtx-supply + - vddhost-supply + - vddcmos-supply + - vddgpio-0-supply + - vddgpio-1-supply + - sensors + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@61 { + compatible = "thine,thp7312"; + reg = <0x61>; + + pinctrl-names = "default"; + pinctrl-0 = <&cam1_pins_default>; + + reset-gpios = <&pio 119 GPIO_ACTIVE_LOW>; + clocks = <&camera61_clk>; + + vddcore-supply = <&vsys_v4p2>; + vhtermrx-supply = <&vsys_v4p2>; + vddtx-supply = <&vsys_v4p2>; + vddhost-supply = <&vsys_v4p2>; + vddcmos-supply = <&vsys_v4p2>; + vddgpio-0-supply = <&vsys_v4p2>; + vddgpio-1-supply = <&vsys_v4p2>; + + orientation = <0>; + rotation = <0>; + + sensors { + #address-cells = <1>; + #size-cells = <0>; + + sensor@0 { + thine,model = "sony,imx258"; + reg = <0>; + + data-lanes = <4 1 3 2>; + }; + }; + + port { + thp7312_2_endpoint: endpoint { + remote-endpoint = <&mipi_thp7312_2>; + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + data-lanes = <4 2 1 3>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub913.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub913.yaml new file mode 100644 index 000000000000..f6612bb0f667 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub913.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub913.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB913 FPD-Link III Serializer + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + +description: + The TI DS90UB913 is an FPD-Link III video serializer for parallel video. + +properties: + compatible: + enum: + - ti,ds90ub913a-q1 + + '#gpio-cells': + const: 2 + description: + First cell is the GPO pin number, second cell is the flags. The GPO pin + number must be in range of [0, 3]. Note that GPOs 2 and 3 are not + available in external oscillator mode. + + gpio-controller: true + + clocks: + maxItems: 1 + description: + Reference clock connected to the CLKIN pin. + + clock-names: + items: + - const: clkin + + '#clock-cells': + const: 0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Parallel input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - pclk-sample + + port@1: + $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + description: FPD-Link III output port + + required: + - port@0 + - port@1 + + i2c: + $ref: /schemas/i2c/i2c-controller.yaml# + unevaluatedProperties: false + +required: + - compatible + - '#gpio-cells' + - gpio-controller + - '#clock-cells' + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + serializer { + compatible = "ti,ds90ub913a-q1"; + + gpio-controller; + #gpio-cells = <2>; + + clocks = <&clk_cam_48M>; + clock-names = "clkin"; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub913_in: endpoint { + remote-endpoint = <&sensor_out>; + pclk-sample = <1>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&deser_fpd_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + + clocks = <&fixed_clock>; + + port { + sensor_out: endpoint { + remote-endpoint = <&ub913_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub953.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub953.yaml new file mode 100644 index 000000000000..2030366994d1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub953.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub953.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB953 FPD-Link III Serializer + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + +description: + The TI DS90UB953 is an FPD-Link III video serializer for MIPI CSI-2. + +properties: + compatible: + enum: + - ti,ds90ub953-q1 + - ti,ds90ub971-q1 + + '#gpio-cells': + const: 2 + description: + First cell is the GPIO pin number, second cell is the flags. The GPIO pin + number must be in range of [0, 3]. + + gpio-controller: true + + clocks: + maxItems: 1 + description: + Reference clock connected to the CLKIN pin. + + clock-names: + items: + - const: clkin + + '#clock-cells': + const: 0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + description: FPD-Link III output port + + required: + - port@0 + - port@1 + + i2c: + $ref: /schemas/i2c/i2c-controller.yaml# + unevaluatedProperties: false + +required: + - compatible + - '#gpio-cells' + - gpio-controller + - '#clock-cells' + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + serializer { + compatible = "ti,ds90ub953-q1"; + + gpio-controller; + #gpio-cells = <2>; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub953_in: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&sensor_out>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&deser_fpd_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + + reset-gpios = <&serializer 0 GPIO_ACTIVE_LOW>; + + clocks = <&serializer>; + clock-names = "inck"; + + port { + sensor_out: endpoint { + remote-endpoint = <&ub953_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml new file mode 100644 index 000000000000..0b71e6f911a8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml @@ -0,0 +1,428 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub960.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB9XX Family FPD-Link Deserializer Hubs + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + +description: + The TI DS90UB9XX devices are FPD-Link video deserializers with I2C and GPIO + forwarding. + +allOf: + - $ref: /schemas/i2c/i2c-atr.yaml# + +properties: + compatible: + enum: + - ti,ds90ub960-q1 + - ti,ds90ub9702-q1 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: + Reference clock connected to the REFCLK pin. + + clock-names: + items: + - const: refclk + + powerdown-gpios: + maxItems: 1 + description: + Specifier for the GPIO connected to the PDB pin. + + i2c-alias-pool: + minItems: 1 + maxItems: 32 + + links: + type: object + additionalProperties: false + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + ti,manual-strobe: + type: boolean + description: + Enable manual strobe position and EQ level + + patternProperties: + '^link@[0-3]$': + type: object + additionalProperties: false + properties: + reg: + description: The link number + maxItems: 1 + + i2c-alias: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The I2C address used for the serializer. Transactions to this + address on the I2C bus where the deserializer resides are + forwarded to the serializer. + + ti,rx-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # RAW10 + - 1 # RAW12 HF + - 2 # RAW12 LF + - 3 # CSI2 SYNC + - 4 # CSI2 NON-SYNC + description: + FPD-Link Input Mode. This should reflect the hardware and the + default mode of the connected device. + + ti,cdr-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # FPD-Link III + - 1 # FPD-Link IV + description: + FPD-Link CDR Mode. This should reflect the hardware and the + default mode of the connected device. + + ti,strobe-pos: + $ref: /schemas/types.yaml#/definitions/int32 + minimum: -13 + maximum: 13 + description: Manual strobe position + + ti,eq-level: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 14 + description: Manual EQ level + + serializer: + type: object + description: FPD-Link Serializer node + + required: + - reg + - i2c-alias + - ti,rx-mode + - serializer + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: FPD-Link input 0 + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + description: + Endpoint for FPD-Link port. If the RX mode for this port is RAW, + hsync-active and vsync-active must be defined. + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: FPD-Link input 1 + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + description: + Endpoint for FPD-Link port. If the RX mode for this port is RAW, + hsync-active and vsync-active must be defined. + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: FPD-Link input 2 + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + description: + Endpoint for FPD-Link port. If the RX mode for this port is RAW, + hsync-active and vsync-active must be defined. + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: FPD-Link input 3 + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + description: + Endpoint for FPD-Link port. If the RX mode for this port is RAW, + hsync-active and vsync-active must be defined. + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output 0 + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + link-frequencies: + maxItems: 1 + + required: + - data-lanes + - link-frequencies + + port@5: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output 1 + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + link-frequencies: + maxItems: 1 + + required: + - data-lanes + - link-frequencies + + required: + - port@0 + - port@1 + - port@2 + - port@3 + - port@4 + - port@5 + +required: + - compatible + - reg + - clocks + - clock-names + - ports + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + + deser@3d { + compatible = "ti,ds90ub960-q1"; + reg = <0x3d>; + + clock-names = "refclk"; + clocks = <&fixed_clock>; + + powerdown-gpios = <&pca9555 7 GPIO_ACTIVE_LOW>; + + i2c-alias-pool = <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Port 0, Camera 0 */ + port@0 { + reg = <0>; + + ub960_fpd3_1_in: endpoint { + remote-endpoint = <&ub953_1_out>; + }; + }; + + /* Port 1, Camera 1 */ + port@1 { + reg = <1>; + + ub960_fpd3_2_in: endpoint { + remote-endpoint = <&ub913_2_out>; + hsync-active = <0>; + vsync-active = <1>; + }; + }; + + /* Port 2, unconnected */ + port@2 { + reg = <2>; + }; + + /* Port 3, unconnected */ + port@3 { + reg = <3>; + }; + + /* Port 4, CSI-2 TX */ + port@4 { + reg = <4>; + ds90ub960_0_csi_out: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <800000000>; + remote-endpoint = <&csi2_phy0>; + }; + }; + + /* Port 5, unconnected */ + port@5 { + reg = <5>; + }; + }; + + links { + #address-cells = <1>; + #size-cells = <0>; + + /* Link 0 has DS90UB953 serializer and IMX274 sensor */ + + link@0 { + reg = <0>; + i2c-alias = <0x44>; + + ti,rx-mode = <3>; + + serializer1: serializer { + compatible = "ti,ds90ub953-q1"; + + gpio-controller; + #gpio-cells = <2>; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub953_1_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&sensor_1_out>; + }; + }; + + port@1 { + reg = <1>; + + ub953_1_out: endpoint { + remote-endpoint = <&ub960_fpd3_1_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + + reset-gpios = <&serializer1 0 GPIO_ACTIVE_LOW>; + + port { + sensor_1_out: endpoint { + remote-endpoint = <&ub953_1_in>; + }; + }; + }; + }; + }; + }; /* End of link@0 */ + + /* Link 1 has DS90UB913 serializer and MT9V111 sensor */ + + link@1 { + reg = <1>; + i2c-alias = <0x45>; + + ti,rx-mode = <0>; + + serializer2: serializer { + compatible = "ti,ds90ub913a-q1"; + + gpio-controller; + #gpio-cells = <2>; + + clocks = <&clk_cam_48M>; + clock-names = "clkin"; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub913_2_in: endpoint { + remote-endpoint = <&sensor_2_out>; + pclk-sample = <1>; + }; + }; + + port@1 { + reg = <1>; + + ub913_2_out: endpoint { + remote-endpoint = <&ub960_fpd3_2_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + + clocks = <&serializer2>; + + port { + sensor_2_out: endpoint { + remote-endpoint = <&ub913_2_in>; + }; + }; + }; + }; + }; + }; /* End of link@1 */ + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml new file mode 100644 index 000000000000..1c476b635b69 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml @@ -0,0 +1,180 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/toshiba,tc358746.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Toshiba TC358746 Parallel to MIPI CSI2 Bridge + +maintainers: + - Marco Felsch <kernel@pengutronix.de> + +description: |- + The Toshiba TC358746 converts a parallel video stream into a MIPI CSI-2 + stream. The direction can be either parallel-in -> csi-out or csi-in -> + parallel-out The chip is programmable through I2C and SPI but the SPI + interface is only supported in parallel-in -> csi-out mode. + + Note that the current device tree bindings only support the + parallel-in -> csi-out path. + +properties: + compatible: + const: toshiba,tc358746 + + reg: + maxItems: 1 + + clocks: + description: + The phandle to the reference clock source. This corresponds to the + hardware pin REFCLK. + maxItems: 1 + + clock-names: + const: refclk + + "#clock-cells": + description: | + The bridge can act as clock provider for the sensor. To enable this + support #clock-cells must be specified. Attention if this feature is used + then the mclk rate must be at least: (2 * link-frequency) / 8 + `------------------ยด ^ + internal PLL rate smallest possible + mclk-div + const: 0 + + clock-output-names: + description: + The clock name of the MCLK output, the default name is tc358746-mclk. + maxItems: 1 + + vddc-supply: + description: Digital core voltage supply, 1.2 volts + + vddio-supply: + description: Digital I/O voltage supply, 1.8 volts + + vddmipi-supply: + description: MIPI CSI phy voltage supply, 1.2 volts + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls the chip reset. + This corresponds to the hardware pin RESX which is physically active low. + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: true + vsync-active: true + bus-type: + enum: [ 5, 6 ] + + required: + - hsync-active + - vsync-active + - bus-type + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + clock-noncontinuous: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - clocks + - clock-names + - vddc-supply + - vddio-supply + - vddmipi-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + csi-bridge@e { + compatible = "toshiba,tc358746"; + reg = <0xe>; + + clocks = <&refclk>; + clock-names = "refclk"; + + reset-gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + + vddc-supply = <&v1_2d>; + vddio-supply = <&v1_8d>; + vddmipi-supply = <&v1_2d>; + + /* sensor mclk provider */ + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Input */ + port@0 { + reg = <0>; + tc358746_in: endpoint { + remote-endpoint = <&sensor_out>; + hsync-active = <0>; + vsync-active = <0>; + bus-type = <5>; + }; + }; + + /* Output */ + port@1 { + reg = <1>; + tc358746_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <216000000>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt index 6c88ce858d08..94b908ace53c 100644 --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -53,10 +53,10 @@ Optional Connector Properties: ============================== - sdtv-standards: Set the possible signals to which the hardware tries to lock - instead of using the autodetection mechnism. Please look at + instead of using the autodetection mechanism. Please look at [1] for more information. -[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. +[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml. Example - three input sources: #include <dt-bindings/display/sdtv-standards.h> |