diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/adc')
15 files changed, 390 insertions, 25 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt new file mode 100644 index 000000000000..d8652460198e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt @@ -0,0 +1,66 @@ +Analog Devices AD7606 Simultaneous Sampling ADC + +Required properties for the AD7606: + +- compatible: Must be one of + * "adi,ad7605-4" + * "adi,ad7606-8" + * "adi,ad7606-6" + * "adi,ad7606-4" + * "adi,ad7616" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt +- avcc-supply: phandle to the Avcc power supply +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin. + This logic input is used to initiate conversions on the analog + input channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Optional properties: + +- reset-gpios: must be the device tree identifier of the RESET pin. If specified, + it will be asserted during driver probe. As the line is active high, + it should be marked GPIO_ACTIVE_HIGH. +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used + to place the AD7606 into one of two power-down modes, Standby mode or + Shutdown mode. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin. + The FRSTDATA output indicates when the first channel, V1, is + being read back on either the parallel, byte or serial interface. + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on + this pin determines the input range of the analog input channels. If + this pin is tied to a logic high, the analog input range is ±10V for + all channels. If this pin is tied to a logic low, the analog input range + is ±5V for all channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. +- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling + mode pins. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Example: + + adc@0 { + compatible = "adi,ad7606-8"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + + avcc-supply = <&adc_vref>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH + &gpio 23 GPIO_ACTIVE_HIGH + &gpio 26 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt new file mode 100644 index 000000000000..9f5b88cf680d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt @@ -0,0 +1,41 @@ +Analog Devices AD7768-1 ADC device driver + +Required properties for the AD7768-1: + +- compatible: Must be "adi,ad7768-1" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- clocks: phandle to the master clock (mclk) + see: Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names: Must be "mclk". +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- vref-supply: vref supply can be used as reference for conversion +- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables + synchronization of multiple devices that require simultaneous sampling. + A pulse is always required if the configuration is changed in any way, for example + if the filter decimation rate changes. As the line is active low, it should + be marked GPIO_ACTIVE_LOW. + +Optional properties: + + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW. + +Example: + + adc@0 { + compatible = "adi,ad7768-1"; + reg = <0>; + spi-max-frequency = <2000000>; + spi-cpol; + spi-cpha; + vref-supply = <&adc_vref>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + clocks = <&ad7768_mclk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt new file mode 100644 index 000000000000..440e52555349 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt @@ -0,0 +1,48 @@ +* Analog Devices AD7170/AD7171/AD7780/AD7781 + +Data sheets: + +- AD7170: + * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7170.pdf +- AD7171: + * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7171.pdf +- AD7780: + * https://www.analog.com/media/en/technical-documentation/data-sheets/ad7780.pdf +- AD7781: + * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7781.pdf + +Required properties: + +- compatible: should be one of + * "adi,ad7170" + * "adi,ad7171" + * "adi,ad7780" + * "adi,ad7781" +- reg: spi chip select number for the device +- vref-supply: the regulator supply for the ADC reference voltage + +Optional properties: + +- powerdown-gpios: must be the device tree identifier of the PDRST pin. If + specified, it will be asserted during driver probe. As the + line is active high, it should be marked GPIO_ACTIVE_HIGH. +- adi,gain-gpios: must be the device tree identifier of the GAIN pin. Only for + the ad778x chips. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. +- adi,filter-gpios: must be the device tree identifier of the FILTER pin. Only + for the ad778x chips. If specified, it will be asserted + during driver probe. As the line is active low, it should be + marked GPIO_ACTIVE_LOW. + +Example: + +adc@0 { + compatible = "adi,ad7780"; + reg = <0>; + vref-supply = <&vdd_supply> + + powerdown-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + adi,gain-gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + adi,filter-gpios = <&gpio 15 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 325090e43ce6..d57e9df25f4f 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -9,6 +9,7 @@ Required properties: - "amlogic,meson-gxl-saradc" for GXL - "amlogic,meson-gxm-saradc" for GXM - "amlogic,meson-axg-saradc" for AXG + - "amlogic,meson-g12a-saradc" for AXG along with the generic "amlogic,meson-saradc" - reg: the physical base address and length of the registers - interrupts: the interrupt indicating end of sampling @@ -23,6 +24,10 @@ Required properties: - #io-channel-cells: must be 1, see ../iio-bindings.txt Optional properties: +- amlogic,hhi-sysctrl: phandle to the syscon which contains the 5th bit + of the TSC (temperature sensor coefficient) on + Meson8b and Meson8m2 (which used to calibrate the + temperature sensor) - nvmem-cells: phandle to the temperature_calib eFuse cells - nvmem-cell-names: if present (to enable the temperature sensor calibration) this must contain "temperature_calib" diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt b/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt deleted file mode 100644 index 7222328a3d0d..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt +++ /dev/null @@ -1,24 +0,0 @@ -* AVIA HX711 ADC chip for weight cells - Bit-banging driver - -Required properties: - - compatible: Should be "avia,hx711" - - sck-gpios: Definition of the GPIO for the clock - - dout-gpios: Definition of the GPIO for data-out - See Documentation/devicetree/bindings/gpio/gpio.txt - - avdd-supply: Definition of the regulator used as analog supply - -Optional properties: - - clock-frequency: Frequency of PD_SCK in Hz - Minimum value allowed is 10 kHz because of maximum - high time of 50 microseconds. - -Example: -weight { - compatible = "avia,hx711"; - sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; - dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - avdd-suppy = <&avdd>; - clock-frequency = <100000>; -}; - diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml b/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml new file mode 100644 index 000000000000..8a4100ceeaf2 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/iio/adc/avia-hx711.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AVIA HX711 ADC chip for weight cells + +maintainers: + - Andreas Klinger <ak@it-klinger.de> + +description: | + Bit-banging driver using two GPIOs: + - sck-gpio gives a clock to the sensor with 24 cycles for data retrieval + and up to 3 cycles for selection of the input channel and gain for the + next measurement + - dout-gpio is the sensor data the sensor responds to the clock + + Specifications about the driver can be found at: + http://www.aviaic.com/ENProducts.aspx + +properties: + compatible: + enum: + - avia,hx711 + + sck-gpios: + description: + Definition of the GPIO for the clock (output). In the datasheet it is + named PD_SCK + maxItems: 1 + + dout-gpios: + description: + Definition of the GPIO for the data-out sent by the sensor in + response to the clock (input). + See Documentation/devicetree/bindings/gpio/gpio.txt for information + on how to specify a consumer gpio. + maxItems: 1 + + avdd-supply: + description: + Definition of the regulator used as analog supply + maxItems: 1 + + clock-frequency: + minimum: 20000 + maximum: 2500000 + default: 400000 + +required: + - compatible + - sck-gpios + - dout-gpios + - avdd-supply + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + weight { + compatible = "avia,hx711"; + sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; + dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + avdd-suppy = <&avdd>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt index 5c184b940669..f1f3a552459b 100644 --- a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt @@ -10,6 +10,7 @@ Required properties: - clocks: The root clock of the ADC controller - clock-names: Must contain "adc", matching entry in the clocks property - vref-supply: The regulator supply ADC reference voltage +- #io-channel-cells: Must be 1 as per ../iio-bindings.txt Example: adc1: adc@30610000 { @@ -19,4 +20,5 @@ adc1: adc@30610000 { clocks = <&clks IMX7D_ADC_ROOT_CLK>; clock-names = "adc"; vref-supply = <®_vcc_3v3_mcu>; + #io-channel-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt new file mode 100644 index 000000000000..f01159f20d87 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt @@ -0,0 +1,48 @@ +* Ingenic JZ47xx ADC controller IIO bindings + +Required properties: + +- compatible: Should be one of: + * ingenic,jz4725b-adc + * ingenic,jz4740-adc +- reg: ADC controller registers location and length. +- clocks: phandle to the SoC's ADC clock. +- clock-names: Must be set to "adc". +- #io-channel-cells: Must be set to <1> to indicate channels are selected + by index. + +ADC clients must use the format described in iio-bindings.txt, giving +a phandle and IIO specifier pair ("io-channels") to the ADC controller. + +Example: + +#include <dt-bindings/iio/adc/ingenic,adc.h> + +adc: adc@10070000 { + compatible = "ingenic,jz4740-adc"; + #io-channel-cells = <1>; + + reg = <0x10070000 0x30>; + + clocks = <&cgu JZ4740_CLK_ADC>; + clock-names = "adc"; + + interrupt-parent = <&intc>; + interrupts = <18>; +}; + +adc-keys { + ... + compatible = "adc-keys"; + io-channels = <&adc INGENIC_ADC_AUX>; + io-channel-names = "buttons"; + ... +}; + +battery { + ... + compatible = "ingenic,jz4740-battery"; + io-channels = <&adc INGENIC_ADC_BATTERY>; + io-channel-names = "battery"; + ... +}; diff --git a/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt new file mode 100644 index 000000000000..3a1bc669bd51 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt @@ -0,0 +1,21 @@ +* NXP LPC32xx SoC ADC controller + +Required properties: +- compatible: must be "nxp,lpc3220-adc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The ADC interrupt + +Optional: + - vref-supply: The regulator supply ADC reference voltage, optional + for legacy reason, but highly encouraging to us in new device tree + +Example: + + adc@40048000 { + compatible = "nxp,lpc3220-adc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + vref-supply = <&vcc>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt new file mode 100644 index 000000000000..eb939fe77836 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt @@ -0,0 +1,24 @@ +Nuvoton NPCM Analog to Digital Converter (ADC) + +The NPCM ADC is a 10-bit converter for eight channel inputs. + +Required properties: +- compatible: "nuvoton,npcm750-adc" for the NPCM7XX BMC. +- reg: specifies physical base address and size of the registers. +- interrupts: Contain the ADC interrupt with flags for falling edge. + +Optional properties: +- clocks: phandle of ADC reference clock, in case the clock is not + added the ADC will use the default ADC sample rate. +- vref-supply: The regulator supply ADC reference voltage, in case the + vref-supply is not added the ADC will use internal voltage + reference. + +Example: + +adc: adc@f000c000 { + compatible = "nuvoton,npcm750-adc"; + reg = <0xf000c000 0x8>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_ADC>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt index c81993f8d8c3..c8787688122a 100644 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt @@ -13,6 +13,7 @@ VADC node: Definition: Should contain "qcom,spmi-vadc". Should contain "qcom,spmi-adc5" for PMIC5 ADC driver. Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver. + Should contain "qcom,pms405-adc" for PMS405 PMIC - reg: Usage: required diff --git a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt index a10c1f89037d..e1fe02f3e3e9 100644 --- a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt @@ -11,11 +11,13 @@ New driver handles the following Required properties: - compatible: Must be "samsung,exynos-adc-v1" - for exynos4412/5250 controllers. + for Exynos5250 controllers. Must be "samsung,exynos-adc-v2" for future controllers. Must be "samsung,exynos3250-adc" for controllers compatible with ADC of Exynos3250. + Must be "samsung,exynos4212-adc" for + controllers compatible with ADC of Exynos4212 and Exynos4412. Must be "samsung,exynos7-adc" for the ADC in Exynos7 and compatibles Must be "samsung,s3c2410-adc" for diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt new file mode 100644 index 000000000000..480e66422625 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt @@ -0,0 +1,21 @@ +STMPE ADC driver +---------------- + +Required properties: + - compatible: "st,stmpe-adc" + +Optional properties: +Note that the ADC is shared with the STMPE touchscreen. ADC related settings +have to be done in the mfd. +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be + requestable due to different usage (e.g. touch) + +Node name must be stmpe_adc and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ + }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt new file mode 100644 index 000000000000..ecf807bb32f7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt @@ -0,0 +1,25 @@ +* Texas Instruments' ads124s08 and ads124s06 ADC chip + +Required properties: + - compatible : + "ti,ads124s08" + "ti,ads124s06" + - reg : spi chip select number for the device + +Recommended properties: + - spi-max-frequency : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - spi-cpha : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - reset-gpios : GPIO pin used to reset the device. + +Example: +adc@0 { + compatible = "ti,ads124s08"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads8344.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads8344.txt new file mode 100644 index 000000000000..e47c3759a82b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads8344.txt @@ -0,0 +1,19 @@ +* Texas Instruments ADS8344 A/DC chip + +Required properties: + - compatible: Must be "ti,ads8344" + - reg: SPI chip select number for the device + - vref-supply: phandle to a regulator node that supplies the + reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,ads8344"; + reg = <0>; + vref-supply = <&refin_supply>; + spi-max-frequency = <10000000>; +}; |