diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
40 files changed, 919 insertions, 109 deletions
diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt new file mode 100644 index 000000000000..eb76a02e2a82 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.txt @@ -0,0 +1,17 @@ +Kionix KXCJK-1013 Accelerometer device tree bindings + +Required properties: + +- compatible: Must be one of: + "kionix,kxcjk1013" + "kionix,kxcj91008" + "kionix,kxtj21009" + "kionix,kxtf9" + - reg: i2c slave address + +Example: + +kxtf9@f { + compatible = "kionix,kxtf9"; + reg = <0x0F>; +}; diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 2100e9af379c..e132394375a1 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -20,6 +20,10 @@ Optional properties: - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's interrupt line in use. + - vdd-supply: phandle to the regulator that provides vdd power to the accelerometer. + + - vddio-supply: phandle to the regulator that provides vddio power to the accelerometer. + Example: mma8453fc@1d { diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt new file mode 100644 index 000000000000..d8652460198e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt @@ -0,0 +1,66 @@ +Analog Devices AD7606 Simultaneous Sampling ADC + +Required properties for the AD7606: + +- compatible: Must be one of + * "adi,ad7605-4" + * "adi,ad7606-8" + * "adi,ad7606-6" + * "adi,ad7606-4" + * "adi,ad7616" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt +- avcc-supply: phandle to the Avcc power supply +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin. + This logic input is used to initiate conversions on the analog + input channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Optional properties: + +- reset-gpios: must be the device tree identifier of the RESET pin. If specified, + it will be asserted during driver probe. As the line is active high, + it should be marked GPIO_ACTIVE_HIGH. +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used + to place the AD7606 into one of two power-down modes, Standby mode or + Shutdown mode. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin. + The FRSTDATA output indicates when the first channel, V1, is + being read back on either the parallel, byte or serial interface. + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on + this pin determines the input range of the analog input channels. If + this pin is tied to a logic high, the analog input range is ±10V for + all channels. If this pin is tied to a logic low, the analog input range + is ±5V for all channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. +- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling + mode pins. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Example: + + adc@0 { + compatible = "adi,ad7606-8"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + + avcc-supply = <&adc_vref>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH + &gpio 23 GPIO_ACTIVE_HIGH + &gpio 26 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt new file mode 100644 index 000000000000..9f5b88cf680d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt @@ -0,0 +1,41 @@ +Analog Devices AD7768-1 ADC device driver + +Required properties for the AD7768-1: + +- compatible: Must be "adi,ad7768-1" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- clocks: phandle to the master clock (mclk) + see: Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names: Must be "mclk". +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- vref-supply: vref supply can be used as reference for conversion +- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables + synchronization of multiple devices that require simultaneous sampling. + A pulse is always required if the configuration is changed in any way, for example + if the filter decimation rate changes. As the line is active low, it should + be marked GPIO_ACTIVE_LOW. + +Optional properties: + + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW. + +Example: + + adc@0 { + compatible = "adi,ad7768-1"; + reg = <0>; + spi-max-frequency = <2000000>; + spi-cpol; + spi-cpha; + vref-supply = <&adc_vref>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + clocks = <&ad7768_mclk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt new file mode 100644 index 000000000000..440e52555349 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt @@ -0,0 +1,48 @@ +* Analog Devices AD7170/AD7171/AD7780/AD7781 + +Data sheets: + +- AD7170: + * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7170.pdf +- AD7171: + * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7171.pdf +- AD7780: + * https://www.analog.com/media/en/technical-documentation/data-sheets/ad7780.pdf +- AD7781: + * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7781.pdf + +Required properties: + +- compatible: should be one of + * "adi,ad7170" + * "adi,ad7171" + * "adi,ad7780" + * "adi,ad7781" +- reg: spi chip select number for the device +- vref-supply: the regulator supply for the ADC reference voltage + +Optional properties: + +- powerdown-gpios: must be the device tree identifier of the PDRST pin. If + specified, it will be asserted during driver probe. As the + line is active high, it should be marked GPIO_ACTIVE_HIGH. +- adi,gain-gpios: must be the device tree identifier of the GAIN pin. Only for + the ad778x chips. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. +- adi,filter-gpios: must be the device tree identifier of the FILTER pin. Only + for the ad778x chips. If specified, it will be asserted + during driver probe. As the line is active low, it should be + marked GPIO_ACTIVE_LOW. + +Example: + +adc@0 { + compatible = "adi,ad7780"; + reg = <0>; + vref-supply = <&vdd_supply> + + powerdown-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + adi,gain-gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + adi,filter-gpios = <&gpio 15 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 325090e43ce6..d57e9df25f4f 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -9,6 +9,7 @@ Required properties: - "amlogic,meson-gxl-saradc" for GXL - "amlogic,meson-gxm-saradc" for GXM - "amlogic,meson-axg-saradc" for AXG + - "amlogic,meson-g12a-saradc" for AXG along with the generic "amlogic,meson-saradc" - reg: the physical base address and length of the registers - interrupts: the interrupt indicating end of sampling @@ -23,6 +24,10 @@ Required properties: - #io-channel-cells: must be 1, see ../iio-bindings.txt Optional properties: +- amlogic,hhi-sysctrl: phandle to the syscon which contains the 5th bit + of the TSC (temperature sensor coefficient) on + Meson8b and Meson8m2 (which used to calibrate the + temperature sensor) - nvmem-cells: phandle to the temperature_calib eFuse cells - nvmem-cell-names: if present (to enable the temperature sensor calibration) this must contain "temperature_calib" diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt b/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt deleted file mode 100644 index 7222328a3d0d..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt +++ /dev/null @@ -1,24 +0,0 @@ -* AVIA HX711 ADC chip for weight cells - Bit-banging driver - -Required properties: - - compatible: Should be "avia,hx711" - - sck-gpios: Definition of the GPIO for the clock - - dout-gpios: Definition of the GPIO for data-out - See Documentation/devicetree/bindings/gpio/gpio.txt - - avdd-supply: Definition of the regulator used as analog supply - -Optional properties: - - clock-frequency: Frequency of PD_SCK in Hz - Minimum value allowed is 10 kHz because of maximum - high time of 50 microseconds. - -Example: -weight { - compatible = "avia,hx711"; - sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; - dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - avdd-suppy = <&avdd>; - clock-frequency = <100000>; -}; - diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml b/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml new file mode 100644 index 000000000000..8a4100ceeaf2 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/iio/adc/avia-hx711.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AVIA HX711 ADC chip for weight cells + +maintainers: + - Andreas Klinger <ak@it-klinger.de> + +description: | + Bit-banging driver using two GPIOs: + - sck-gpio gives a clock to the sensor with 24 cycles for data retrieval + and up to 3 cycles for selection of the input channel and gain for the + next measurement + - dout-gpio is the sensor data the sensor responds to the clock + + Specifications about the driver can be found at: + http://www.aviaic.com/ENProducts.aspx + +properties: + compatible: + enum: + - avia,hx711 + + sck-gpios: + description: + Definition of the GPIO for the clock (output). In the datasheet it is + named PD_SCK + maxItems: 1 + + dout-gpios: + description: + Definition of the GPIO for the data-out sent by the sensor in + response to the clock (input). + See Documentation/devicetree/bindings/gpio/gpio.txt for information + on how to specify a consumer gpio. + maxItems: 1 + + avdd-supply: + description: + Definition of the regulator used as analog supply + maxItems: 1 + + clock-frequency: + minimum: 20000 + maximum: 2500000 + default: 400000 + +required: + - compatible + - sck-gpios + - dout-gpios + - avdd-supply + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + weight { + compatible = "avia,hx711"; + sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; + dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + avdd-suppy = <&avdd>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt index 5c184b940669..f1f3a552459b 100644 --- a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt @@ -10,6 +10,7 @@ Required properties: - clocks: The root clock of the ADC controller - clock-names: Must contain "adc", matching entry in the clocks property - vref-supply: The regulator supply ADC reference voltage +- #io-channel-cells: Must be 1 as per ../iio-bindings.txt Example: adc1: adc@30610000 { @@ -19,4 +20,5 @@ adc1: adc@30610000 { clocks = <&clks IMX7D_ADC_ROOT_CLK>; clock-names = "adc"; vref-supply = <®_vcc_3v3_mcu>; + #io-channel-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt new file mode 100644 index 000000000000..f01159f20d87 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt @@ -0,0 +1,48 @@ +* Ingenic JZ47xx ADC controller IIO bindings + +Required properties: + +- compatible: Should be one of: + * ingenic,jz4725b-adc + * ingenic,jz4740-adc +- reg: ADC controller registers location and length. +- clocks: phandle to the SoC's ADC clock. +- clock-names: Must be set to "adc". +- #io-channel-cells: Must be set to <1> to indicate channels are selected + by index. + +ADC clients must use the format described in iio-bindings.txt, giving +a phandle and IIO specifier pair ("io-channels") to the ADC controller. + +Example: + +#include <dt-bindings/iio/adc/ingenic,adc.h> + +adc: adc@10070000 { + compatible = "ingenic,jz4740-adc"; + #io-channel-cells = <1>; + + reg = <0x10070000 0x30>; + + clocks = <&cgu JZ4740_CLK_ADC>; + clock-names = "adc"; + + interrupt-parent = <&intc>; + interrupts = <18>; +}; + +adc-keys { + ... + compatible = "adc-keys"; + io-channels = <&adc INGENIC_ADC_AUX>; + io-channel-names = "buttons"; + ... +}; + +battery { + ... + compatible = "ingenic,jz4740-battery"; + io-channels = <&adc INGENIC_ADC_BATTERY>; + io-channel-names = "battery"; + ... +}; diff --git a/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt new file mode 100644 index 000000000000..3a1bc669bd51 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt @@ -0,0 +1,21 @@ +* NXP LPC32xx SoC ADC controller + +Required properties: +- compatible: must be "nxp,lpc3220-adc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The ADC interrupt + +Optional: + - vref-supply: The regulator supply ADC reference voltage, optional + for legacy reason, but highly encouraging to us in new device tree + +Example: + + adc@40048000 { + compatible = "nxp,lpc3220-adc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + vref-supply = <&vcc>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt new file mode 100644 index 000000000000..eb939fe77836 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt @@ -0,0 +1,24 @@ +Nuvoton NPCM Analog to Digital Converter (ADC) + +The NPCM ADC is a 10-bit converter for eight channel inputs. + +Required properties: +- compatible: "nuvoton,npcm750-adc" for the NPCM7XX BMC. +- reg: specifies physical base address and size of the registers. +- interrupts: Contain the ADC interrupt with flags for falling edge. + +Optional properties: +- clocks: phandle of ADC reference clock, in case the clock is not + added the ADC will use the default ADC sample rate. +- vref-supply: The regulator supply ADC reference voltage, in case the + vref-supply is not added the ADC will use internal voltage + reference. + +Example: + +adc: adc@f000c000 { + compatible = "nuvoton,npcm750-adc"; + reg = <0xf000c000 0x8>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_ADC>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt index c81993f8d8c3..c8787688122a 100644 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt @@ -13,6 +13,7 @@ VADC node: Definition: Should contain "qcom,spmi-vadc". Should contain "qcom,spmi-adc5" for PMIC5 ADC driver. Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver. + Should contain "qcom,pms405-adc" for PMS405 PMIC - reg: Usage: required diff --git a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt index a10c1f89037d..e1fe02f3e3e9 100644 --- a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt @@ -11,11 +11,13 @@ New driver handles the following Required properties: - compatible: Must be "samsung,exynos-adc-v1" - for exynos4412/5250 controllers. + for Exynos5250 controllers. Must be "samsung,exynos-adc-v2" for future controllers. Must be "samsung,exynos3250-adc" for controllers compatible with ADC of Exynos3250. + Must be "samsung,exynos4212-adc" for + controllers compatible with ADC of Exynos4212 and Exynos4412. Must be "samsung,exynos7-adc" for the ADC in Exynos7 and compatibles Must be "samsung,s3c2410-adc" for diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt new file mode 100644 index 000000000000..480e66422625 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt @@ -0,0 +1,21 @@ +STMPE ADC driver +---------------- + +Required properties: + - compatible: "st,stmpe-adc" + +Optional properties: +Note that the ADC is shared with the STMPE touchscreen. ADC related settings +have to be done in the mfd. +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be + requestable due to different usage (e.g. touch) + +Node name must be stmpe_adc and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ + }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt new file mode 100644 index 000000000000..ecf807bb32f7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt @@ -0,0 +1,25 @@ +* Texas Instruments' ads124s08 and ads124s06 ADC chip + +Required properties: + - compatible : + "ti,ads124s08" + "ti,ads124s06" + - reg : spi chip select number for the device + +Recommended properties: + - spi-max-frequency : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - spi-cpha : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - reset-gpios : GPIO pin used to reset the device. + +Example: +adc@0 { + compatible = "ti,ads124s08"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads8344.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads8344.txt new file mode 100644 index 000000000000..e47c3759a82b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads8344.txt @@ -0,0 +1,19 @@ +* Texas Instruments ADS8344 A/DC chip + +Required properties: + - compatible: Must be "ti,ads8344" + - reg: SPI chip select number for the device + - vref-supply: phandle to a regulator node that supplies the + reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,ads8344"; + reg = <0>; + vref-supply = <&refin_supply>; + spi-max-frequency = <10000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/bme680.txt b/Documentation/devicetree/bindings/iio/chemical/bme680.txt new file mode 100644 index 000000000000..7f3827cfb2ff --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/bme680.txt @@ -0,0 +1,11 @@ +Bosch Sensortec BME680 pressure/temperature/humidity/voc sensors + +Required properties: +- compatible: must be "bosch,bme680" + +Example: + +bme680@76 { + compatible = "bosch,bme680"; + reg = <0x76>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt new file mode 100644 index 000000000000..c52ea2126eaa --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt @@ -0,0 +1,26 @@ +* Plantower PMS7003 particulate matter sensor + +Required properties: +- compatible: must one of: + "plantower,pms1003" + "plantower,pms3003" + "plantower,pms5003" + "plantower,pms6003" + "plantower,pms7003" + "plantower,pmsa003" +- vcc-supply: phandle to the regulator that provides power to the sensor + +Optional properties: +- plantower,set-gpios: phandle to the GPIO connected to the SET line +- reset-gpios: phandle to the GPIO connected to the RESET line + +Refer to serial/slave-device.txt for generic serial attached device bindings. + +Example: + +&uart0 { + air-pollution-sensor { + compatible = "plantower,pms7003"; + vcc-supply = <®_vcc5v0>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt new file mode 100644 index 000000000000..5844ed58173c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt @@ -0,0 +1,15 @@ +* Sensirion SGP30/SGPC3 multi-pixel Gas Sensor + +Required properties: + + - compatible: must be one of + "sensirion,sgp30" + "sensirion,sgpc3" + - reg: the I2C address of the sensor + +Example: + +gas@58 { + compatible = "sensirion,sgp30"; + reg = <0x58>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt new file mode 100644 index 000000000000..6eee2709b5b6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt @@ -0,0 +1,12 @@ +* Sensirion SPS30 particulate matter sensor + +Required properties: +- compatible: must be "sensirion,sps30" +- reg: the I2C address of the sensor + +Example: + +sps30@69 { + compatible = "sensirion,sps30"; + reg = <0x69>; +}; diff --git a/Documentation/devicetree/bindings/iio/counter/stm32-lptimer-cnt.txt b/Documentation/devicetree/bindings/iio/counter/stm32-lptimer-cnt.txt deleted file mode 100644 index a04aa5c04103..000000000000 --- a/Documentation/devicetree/bindings/iio/counter/stm32-lptimer-cnt.txt +++ /dev/null @@ -1,27 +0,0 @@ -STMicroelectronics STM32 Low-Power Timer quadrature encoder and counter - -STM32 Low-Power Timer provides several counter modes. It can be used as: -- quadrature encoder to detect angular position and direction of rotary - elements, from IN1 and IN2 input signals. -- simple counter from IN1 input signal. - -Must be a sub-node of an STM32 Low-Power Timer device tree node. -See ../mfd/stm32-lptimer.txt for details about the parent node. - -Required properties: -- compatible: Must be "st,stm32-lptimer-counter". -- pinctrl-names: Set to "default". -- pinctrl-0: List of phandles pointing to pin configuration nodes, - to set IN1/IN2 pins in mode of operation for Low-Power - Timer input on external pin. - -Example: - timer@40002400 { - compatible = "st,stm32-lptimer"; - ... - counter { - compatible = "st,stm32-lptimer-counter"; - pinctrl-names = "default"; - pinctrl-0 = <&lptim1_in_pins>; - }; - }; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt new file mode 100644 index 000000000000..639c94ed83e9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt @@ -0,0 +1,28 @@ +* Texas Instruments Dual, 12-Bit Serial Input Digital-to-Analog Converter + +The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with guaranteed +12-bit monotonicity performance over the industrial temperature range. +Is is programmable through an SPI interface. + +The internal DACs are loaded when the LOADDACS pin is pulled down. + +http://www.ti.com/lit/ds/sbas106/sbas106.pdf + +Required Properties: +- compatible: Should be one of: + "ti,dac7612" + "ti,dac7612u" + "ti,dac7612ub" +- reg: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional Properties: +- ti,loaddacs-gpios: GPIO descriptor for the LOADDACS pin. +- spi-*: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + dac@1 { + compatible = "ti,dac7612"; + reg = <0x1>; + ti,loaddacs-gpios = <&msmgpio 25 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/gyroscope/bmg160.txt b/Documentation/devicetree/bindings/iio/gyroscope/bmg160.txt new file mode 100644 index 000000000000..78e18a1e9c1d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/bmg160.txt @@ -0,0 +1,20 @@ +* Bosch BMG160 triaxial rotation sensor (gyroscope) + +Required properties: + + - compatible : should be "bosch,bmg160" or "bosch,bmi055_gyro" + - reg : the I2C address of the sensor (0x69) + +Optional properties: + + - interrupts : interrupt mapping for GPIO IRQ, it should by configured with + flags IRQ_TYPE_EDGE_RISING + +Example: + +bmg160@69 { + compatible = "bosch,bmg160"; + reg = <0x69>; + interrupt-parent = <&gpio6>; + interrupts = <18 (IRQ_TYPE_EDGE_RISING)>; +}; diff --git a/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.txt b/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.txt new file mode 100644 index 000000000000..465e104bbf14 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/nxp,fxas21002c.txt @@ -0,0 +1,31 @@ +* NXP FXAS21002C Gyroscope device tree bindings + +http://www.nxp.com/products/sensors/gyroscopes/3-axis-digital-gyroscope:FXAS21002C + +Required properties: + - compatible : should be "nxp,fxas21002c" + - reg : the I2C address of the sensor or SPI chip select number for the + device. + - vdd-supply: phandle to the regulator that provides power to the sensor. + - vddio-supply: phandle to the regulator that provides power to the bus. + +Optional properties: + - reset-gpios : gpio used to reset the device, see gpio/gpio.txt + - interrupts : device support 2 interrupts, INT1 and INT2, + the interrupts can be triggered on rising or falling edges. + See interrupt-controller/interrupts.txt + - interrupt-names: should contain "INT1" or "INT2", the gyroscope interrupt + line in use. + - drive-open-drain: the interrupt/data ready line will be configured + as open drain, which is useful if several sensors share + the same interrupt line. This is a boolean property. + (This binding is taken from pinctrl/pinctrl-bindings.txt) + +Example: + +gyroscope@20 { + compatible = "nxp,fxas21002c"; + reg = <0x20>; + vdd-supply = <®_peri_3p15v>; + vddio-supply = <®_peri_3p15v>; +}; diff --git a/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt new file mode 100644 index 000000000000..5ff38728ff91 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt @@ -0,0 +1,26 @@ +Analog Devices AD5933/AD5934 Impedance Converter, Network Analyzer + +https://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdf +https://www.analog.com/media/en/technical-documentation/data-sheets/AD5934.pdf + +Required properties: + - compatible : should be one of + "adi,ad5933" + "adi,ad5934" + - reg : the I2C address. + - vdd-supply : The regulator supply for DVDD, AVDD1 and AVDD2 when they + are connected together. + +Optional properties: +- clocks : external clock reference. +- clock-names : must be "mclk" if clocks is set. + +Example for a I2C device node: + + impedance-analyzer@0d { + compatible = "adi,adxl345"; + reg = <0x0d>; + vdd-supply = <&vdd_supply>; + clocks = <&ref_clk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt new file mode 100644 index 000000000000..ed7783f45233 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt @@ -0,0 +1,85 @@ + +Analog Devices ADIS16480 and similar IMUs + +Required properties for the ADIS16480: + +- compatible: Must be one of + * "adi,adis16375" + * "adi,adis16480" + * "adi,adis16485" + * "adi,adis16488" + * "adi,adis16495-1" + * "adi,adis16495-2" + * "adi,adis16495-3" + * "adi,adis16497-1" + * "adi,adis16497-2" + * "adi,adis16497-3" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt +- spi-cpol: See Documentation/devicetree/bindings/spi/spi-bus.txt +- interrupts: interrupt mapping for IRQ, accepted values are: + * IRQF_TRIGGER_RISING + * IRQF_TRIGGER_FALLING + +Optional properties: + +- interrupt-names: Data ready line selection. Valid values are: + * DIO1 + * DIO2 + * DIO3 + * DIO4 + If this field is left empty, DIO1 is assigned as default data ready + signal. +- reset-gpios: must be the device tree identifier of the RESET pin. As the line + is active low, it should be marked GPIO_ACTIVE_LOW. +- clocks: phandle to the external clock. Should be set according to + "clock-names". + If this field is left empty together with the "clock-names" field, then + the internal clock is used. +- clock-names: The name of the external clock to be used. Valid values are: + * sync: In sync mode, the internal clock is disabled and the frequency + of the external clock signal establishes therate of data + collection and processing. See Fig 14 and 15 in the datasheet. + The clock-frequency must be: + * 3000 to 4500 Hz for adis1649x devices. + * 700 to 2400 Hz for adis1648x devices. + * pps: In Pulse Per Second (PPS) Mode, the rate of data collection and + production is equal to the product of the external clock + frequency and the scale factor in the SYNC_SCALE register, see + Table 154 in the datasheet. + The clock-frequency must be: + * 1 to 128 Hz for adis1649x devices. + * This mode is not supported by adis1648x devices. + If this field is left empty together with the "clocks" field, then the + internal clock is used. +- adi,ext-clk-pin: The DIOx line to be used as an external clock input. + Valid values are: + * DIO1 + * DIO2 + * DIO3 + * DIO4 + Each DIOx pin supports only one function at a time (data ready line + selection or external clock input). When a single pin has two + two assignments, the enable bit for the lower priority function + automatically resets to zero (disabling the lower priority function). + Data ready has highest priority. + If this field is left empty, DIO2 is assigned as default external clock + input pin. + +Example: + + imu@0 { + compatible = "adi,adis16495-1"; + reg = <0>; + spi-max-frequency = <3200000>; + spi-cpol; + spi-cpha; + interrupts = <25 IRQF_TRIGGER_FALLING>; + interrupt-parent = <&gpio>; + interrupt-names = "DIO2"; + clocks = <&adis16495_sync>; + clock-names = "sync"; + adi,ext-clk-pin = "DIO1"; + }; diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt index 0c1c105fb503..900c169de00f 100644 --- a/Documentation/devicetree/bindings/iio/imu/bmi160.txt +++ b/Documentation/devicetree/bindings/iio/imu/bmi160.txt @@ -9,9 +9,11 @@ Required properties: - spi-max-frequency : set maximum clock frequency (only for SPI) Optional properties: - - interrupts : interrupt mapping for IRQ, must be IRQ_TYPE_LEVEL_LOW + - interrupts : interrupt mapping for IRQ - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt input, set to "INT2" if INT2 pin should be used instead + - drive-open-drain : set if the specified interrupt pin should be configured as + open drain. If not set, defaults to push-pull. Examples: @@ -20,7 +22,7 @@ bmi160@68 { reg = <0x68>; interrupt-parent = <&gpio4>; - interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; interrupt-names = "INT1"; }; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index 6ab9a9d196b0..268bf7568e19 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -11,6 +11,7 @@ Required properties: "invensense,mpu9250" "invensense,mpu9255" "invensense,icm20608" + "invensense,icm20602" - reg : the I2C address of the sensor - interrupts: interrupt mapping for IRQ. It should be configured with flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index 69d53d98d0f0..efec9ece034a 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -8,6 +8,9 @@ Required properties: "st,lsm6dsm" "st,ism330dlc" "st,lsm6dso" + "st,asm330lhh" + "st,lsm6dsox" + "st,lsm6dsr" - reg: i2c address of the sensor / spi cs line Optional properties: diff --git a/Documentation/devicetree/bindings/iio/light/max44009.txt b/Documentation/devicetree/bindings/iio/light/max44009.txt new file mode 100644 index 000000000000..4a98848e35c0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/max44009.txt @@ -0,0 +1,24 @@ +* MAX44009 Ambient Light Sensor + +Required properties: + +- compatible: should be "maxim,max44009" +- reg: the I2C address of the device (default is <0x4a>) + +Optional properties: + +- interrupts: interrupt mapping for GPIO IRQ. Should be configured with + IRQ_TYPE_EDGE_FALLING. + +Refer to interrupt-controller/interrupts.txt for generic interrupt client +node bindings. + +Example: + +light-sensor@4a { + compatible = "maxim,max44009"; + reg = <0x4a>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/vcnl4000.txt b/Documentation/devicetree/bindings/iio/light/vcnl4000.txt new file mode 100644 index 000000000000..955af4555c90 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/vcnl4000.txt @@ -0,0 +1,24 @@ +VISHAY VCNL4000 - Ambient Light and proximity sensor + +This driver supports the VCNL4000/10/20/40 and VCNL4200 chips + +Required properties: + + -compatible: must be one of : + vishay,vcnl4000 + vishay,vcnl4010 + vishay,vcnl4020 + vishay,vcnl4040 + vishay,vcnl4200 + + -reg: I2C address of the sensor, should be one from below based on the model: + 0x13 + 0x51 + 0x60 + +Example: + +light-sensor@51 { + compatible = "vishay,vcnl4200"; + reg = <0x51>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt deleted file mode 100644 index 61c72e63c584..000000000000 --- a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt +++ /dev/null @@ -1,27 +0,0 @@ -BMP085/BMP18x/BMP28x digital pressure sensors - -Required properties: -- compatible: must be one of: - "bosch,bmp085" - "bosch,bmp180" - "bosch,bmp280" - "bosch,bme280" - -Optional properties: -- interrupts: interrupt mapping for IRQ -- reset-gpios: a GPIO line handling reset of the sensor: as the line is - active low, it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt) -- vddd-supply: digital voltage regulator (see regulator/regulator.txt) -- vdda-supply: analog voltage regulator (see regulator/regulator.txt) - -Example: - -pressure@77 { - compatible = "bosch,bmp085"; - reg = <0x77>; - interrupt-parent = <&gpio0>; - interrupts = <25 IRQ_TYPE_EDGE_RISING>; - reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; - vddd-supply = <&foo>; - vdda-supply = <&bar>; -}; diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml b/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml new file mode 100644 index 000000000000..c6721a7e8938 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/pressure/bmp085.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: BMP085/BMP180/BMP280/BME280 pressure iio sensors + +maintainers: + - Andreas Klinger <ak@it-klinger.de> + +description: | + Pressure, temperature and humidity iio sensors with i2c and spi interfaces + + Specifications about the sensor can be found at: + https://www.bosch-sensortec.com/bst/products/all_products/bmp180 + https://www.bosch-sensortec.com/bst/products/all_products/bmp280 + https://www.bosch-sensortec.com/bst/products/all_products/bme280 + +properties: + compatible: + enum: + - bosch,bmp085 + - bosch,bmp180 + - bosch,bmp280 + - bosch,bme280 + + vddd-supply: + description: + digital voltage regulator (see regulator/regulator.txt) + maxItems: 1 + + vdda-supply: + description: + analog voltage regulator (see regulator/regulator.txt) + maxItems: 1 + + reset-gpios: + description: + A GPIO line handling reset of the sensor. As the line is active low, + it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt) + maxItems: 1 + + interrupts: + description: + interrupt mapping for IRQ (BMP085 only) + maxItems: 1 + +required: + - compatible + - vddd-supply + - vdda-supply + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + pressure@77 { + compatible = "bosch,bmp085"; + reg = <0x77>; + interrupt-parent = <&gpio0>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + vddd-supply = <&foo>; + vdda-supply = <&bar>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.txt b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.txt deleted file mode 100644 index d4dc7a227e2e..000000000000 --- a/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.txt +++ /dev/null @@ -1,28 +0,0 @@ -* Devantech SRF04 ultrasonic range finder - Bit-banging driver using two GPIOs - -Required properties: - - compatible: Should be "devantech,srf04" - - - trig-gpios: Definition of the GPIO for the triggering (output) - This GPIO is set for about 10 us by the driver to tell the - device it should initiate the measurement cycle. - - - echo-gpios: Definition of the GPIO for the echo (input) - This GPIO is set by the device as soon as an ultrasonic - burst is sent out and reset when the first echo is - received. - Thus this GPIO is set while the ultrasonic waves are doing - one round trip. - It needs to be an GPIO which is able to deliver an - interrupt because the time between two interrupts is - measured in the driver. - See Documentation/devicetree/bindings/gpio/gpio.txt for - information on how to specify a consumer gpio. - -Example: -srf04@0 { - compatible = "devantech,srf04"; - trig-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; - echo-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml new file mode 100644 index 000000000000..4e80ea7c1475 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/devantech-srf04.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Devantech SRF04 and Maxbotix mb1000 ultrasonic range finder + +maintainers: + - Andreas Klinger <ak@it-klinger.de> + +description: | + Bit-banging driver using two GPIOs: + - trigger-gpio is raised by the driver to start sending out an ultrasonic + burst + - echo-gpio is held high by the sensor after sending ultrasonic burst + until it is received once again + + Specifications about the devices can be found at: + http://www.robot-electronics.co.uk/htm/srf04tech.htm + + http://www.maxbotix.com/documents/LV-MaxSonar-EZ_Datasheet.pdf + +properties: + compatible: + enum: + - devantech,srf04 + - maxbotix,mb1000 + - maxbotix,mb1010 + - maxbotix,mb1020 + - maxbotix,mb1030 + - maxbotix,mb1040 + + trig-gpios: + description: + Definition of the GPIO for the triggering (output) + This GPIO is set for about 10 us by the driver to tell the device it + should initiate the measurement cycle. + See Documentation/devicetree/bindings/gpio/gpio.txt for information + on how to specify a consumer gpio. + maxItems: 1 + + echo-gpios: + description: + Definition of the GPIO for the echo (input) + This GPIO is set by the device as soon as an ultrasonic burst is sent + out and reset when the first echo is received. + Thus this GPIO is set while the ultrasonic waves are doing one round + trip. + It needs to be an GPIO which is able to deliver an interrupt because + the time between two interrupts is measured in the driver. + maxItems: 1 + +required: + - compatible + - trig-gpios + - echo-gpios + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + proximity { + compatible = "devantech,srf04"; + trig-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + echo-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.txt b/Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.txt new file mode 100644 index 000000000000..dd1058fbe9c3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.txt @@ -0,0 +1,29 @@ +* MaxBotix I2CXL-MaxSonar ultrasonic distance sensor of type mb1202, + mb1212, mb1222, mb1232, mb1242, mb7040 or mb7137 using the i2c interface + for ranging + +Required properties: + - compatible: "maxbotix,mb1202", + "maxbotix,mb1212", + "maxbotix,mb1222", + "maxbotix,mb1232", + "maxbotix,mb1242", + "maxbotix,mb7040" or + "maxbotix,mb7137" + + - reg: i2c address of the device, see also i2c/i2c.txt + +Optional properties: + - interrupts: Interrupt used to announce the preceding reading + request has finished and that data is available. + If no interrupt is specified the device driver + falls back to wait a fixed amount of time until + data can be retrieved. + +Example: +proximity@70 { + compatible = "maxbotix,mb1232"; + reg = <0x70>; + interrupt-parent = <&gpio2>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index ddcb95509599..0ef64a444479 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -49,6 +49,7 @@ Accelerometers: - st,lis2dw12 - st,lis3dhh - st,lis3de +- st,lis2de12 Gyroscopes: - st,l3g4200d-gyro @@ -77,3 +78,4 @@ Pressure sensors: - st,lps22hb-press - st,lps33hw - st,lps35hw +- st,lps22hh diff --git a/Documentation/devicetree/bindings/iio/temperature/max31856.txt b/Documentation/devicetree/bindings/iio/temperature/max31856.txt new file mode 100644 index 000000000000..06ab43bb4de8 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/max31856.txt @@ -0,0 +1,24 @@ +Maxim MAX31856 thermocouple support + +https://datasheets.maximintegrated.com/en/ds/MAX31856.pdf + +Optional property: + - thermocouple-type: Type of thermocouple (THERMOCOUPLE_TYPE_K if + omitted). Supported types are B, E, J, K, N, R, S, T. + +Required properties: + - compatible: must be "maxim,max31856" + - reg: SPI chip select number for the device + - spi-max-frequency: As per datasheet max. supported freq is 5000000 + - spi-cpha: must be defined for max31856 to enable SPI mode 1 + + Refer to spi/spi-bus.txt for generic SPI slave bindings. + + Example: + temp-sensor@0 { + compatible = "maxim,max31856"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + thermocouple-type = <THERMOCOUPLE_TYPE_K>; + }; diff --git a/Documentation/devicetree/bindings/iio/temperature/temperature-bindings.txt b/Documentation/devicetree/bindings/iio/temperature/temperature-bindings.txt new file mode 100644 index 000000000000..8f339cab74ae --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/temperature-bindings.txt @@ -0,0 +1,7 @@ +If the temperature sensor device can be configured to use some specific +thermocouple type, you can use the defined types provided in the file +"include/dt-bindings/iio/temperature/thermocouple.h". + +Property: +thermocouple-type: A single cell representing the type of the thermocouple + used by the device. |