Age | Commit message (Collapse) | Author |
|
Update the README for building the layer
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Update README.booting.md to include SD install steps for ZynqMP. There
are small but important differences compared to Zynq.
Signed-off-by: Martin Lund <malu@gomspace.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
This recipe allows user to fetch the MALI 400 binaries from xilinx.com
manually and use it with compatible machines based on UltraScale+ for
libgles1/libgles2 and egl libraries.
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
The Minized has a wireless connectivity (WiFi / Bluetooth). This recipes
add drivers to use the murata wireless module.
Signed-off-by: Clement Laigle <clement.laigle8@gmail.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
MiniZed is a single-core Zynq 7Z007S development board
Connectivity with Murata "Type 1DX" wireless module
- Wi-Fi 802.11b/g/n
- Bluetooth 4.1 - BLE (Bluetooth Low Energy)
Memory
- 512MB DDR3L
- 128MB QSPI Flash
- 8GB eMMC
Interfaces
- Dual Pmod (16 GPIO)
- Arduino (22 GPIO)
- USB 2.0 host
Physical interface
- Two user LED (Red/Green)
- User button
- User switch
- Reset
Only a single microUSB cable is required for power, programming, JTAG
and serial terminal for debug.
This patch adds machine configuration file for MiniZed board with
required setting of board specific yocto variables needed.
- linux-xlnx is the kernel provider
- u-boot is the u-boot provider which will also generate SPL
boot.bin
Signed-off-by: Clement Laigle <clement.laigle8@gmail.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Backport the u-boot MiniZed support from v2018.7 release.
Signed-off-by: Clement Laigle <clement.laigle8@gmail.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Signed-off-by: Clement Laigle <clement.laigle8@gmail.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Set package arch of VCU to SOC_FAMILY. Even though VCU hwcodec is
available only in ev devices, we are enabling the package for all MPSoC
devices.
gstreamer is the application used for video pipelining. When the VCU HW
is not found, the behaviour will default to using software based
gstreamer (in case of cg and eg devices).
By making package arch common for all zynqmp devices, we can use the
same sstate-cache and RPM feeds for gstreamer components.
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
MALI 400 is available only for eg and ev devices. Set compatible string
and package arch to reflect the same.
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add appropriate SOC_VARIANT for each machine configuration. This is
required from the introduction of overrides based on SOC_VARIANT.
Available SOC_VARIANT's for UltraScale+ MPSoC:
"cg" - Zynq UltraScale+ CG Devices
"eg" - Zynq UltraScale+ EG Devices
"ev" - Zynq UltraScale+ EV Devices
Add SOC_VARIANT to zcu102 board. Default variant is EG device.
Add SOC_VARIANT to zcu104 board. Default variant is EV device.
Add SOC_VARIANT to zcu106 board. Default variant is EV device.
Available SOC_VARIANT's for zynq:
"7zs" - Zynq-7000 Single A9 Core
"7z" - Zynq-7000 Dual A9 Core
Add SOC_VARIANT to zc702 board. Default variant is 7z device.
Add SOC_VARIANT to zc706 board.Default variant is 7z device.
Add SOC_VARIANT to microzed board.Default variant is 7z device.
Add SOC_VARIANT to picozed board.Default variant is 7z device.
Add SOC_VARIANT to zedboard board.Default variant is 7z device.
Add SOC_VARIANT to zybo board.Default variant is 7z device.
Add SOC_VARIANT to qemu-zynq7 board.Default variant is 7z device.
Signed-off-by: Vineeth Chowdary Karumanchi <vineethchowz.chowdary@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
zynq-7000 devices are mainly shipped in 2 variants.
https://www.xilinx.com/products/silicon-devices/soc/zynq-7000.html#productTable
Available SOC_VARIANT's for zynq:
"7zs" - Zynq-7000 Single A9 Core
"7z" - Zynq-7000 Dual A9 Core
This will extend MACHINEOVERRIDES for each device variant as:
7zs --> zynq7zs
7z --> zynq7z
This patch sets the default value of SOC_VARIANT to 7z. This can be
overriden in machine configuration to match the intended FPGA device.
Signed-off-by: Vineeth Chowdary Karumanchi <vineethchowz.chowdary@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
UltraScale MPSoC is shipped in 3 device variants.
https://www.xilinx.com/products/silicon-devices/soc/zynq-ultrascale-mpsoc.html#productTable
Available SOC_VARIANT's for zynqmp:
"cg" - Zynq UltraScale+ CG Devices
"eg" - Zynq UltraScale+ EG Devices (MALI 400)
"ev" - Zynq UltraScale+ EV Devices (MALI 400 + VCU)
This will extend MACHINEOVERRIDES for each device variant as:
cg --> zynqmpcg
eg --> zynqmpeg
ev --> zynqmpev
This patch sets the default value of SOC_VARIANT to eg. This can be
overriden in machine configuration to match the intended FPGA device.
Signed-off-by: Vineeth Chowdary Karumanchi <vineethchowz.chowdary@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
features
This patch enables to add overrides depending on the SoC capabilities.
UltraScale+ FPGA has different variants of silicon to support different
features like MALI400, VCU. Categorically there are three variants: cg
devices, eg devices(MALI 400) and ev devices (MALI 400+ VCU)
See:
https://www.xilinx.com/products/silicon-devices/soc/zynq-ultrascale-mpsoc.html#productTable
dr devices are based for UltraScale+ RFSoC
This patch allows machineoverides to be extended as zynqmp(cg|eg|ev|dr)
and mali400/vcu (based on functionality). This helps in grouping of
settings for similar SoC
This patch also adds packages to be a part of the feed based on
SOC_FAMILY and SOC_VARIANT
Signed-off-by: Alejandro Enedino Hernandez Samaniego <alejandr@xilinx.com>
Signed-off-by: Vineeth Chowdary Karumanchi <vineethchowz.chowdary@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
The ZCU104 Evaluation Kit enables designers to jumpstart designs for
embedded vision applications such as surveillance, Advanced Driver
Assisted Systems (ADAS), machine vision, Augmented Reality (AR), drones
and medical imaging. This kit features a Zynq® UltraScale+™ MPSoC EV
device with video codec and supports many common peripherals and
interfaces for embedded vision use case. The included ZU7EV device is
equipped with a quad-core ARM® Cortex™-A53 applications processor,
dual-core Cortex-R5 real-time processor, Mali™-400 MP2 graphics
processing unit, 4KP60 capable H.264/H.265 video codec, and 16nm FinFET+
programmable logic.
This patch adds machine configuration file for ZCU104 Evaluation Kit
with required setting of board specific yocto variables needed for
compilation of bootloader, kernel and device-tree.
- linux-xlnx is the kernel provider
- u-boot-xlnx is the u-boot provider which will also generate SPL
boot.bin
- hwcodec is provided by libomxil-xlnx recipe, this will pull in
additional dependencies of VCU kernel modules, control software,
firmware binaries
Depending on the application need you may want to pass the appropriate
CMA size in bootargs or set CONFIG_CMA_SIZE_MBYTES in kernel.
While using SPL flow, you may need to provide additional hack to pass
the PMU config object. This is similar to all ZU+ boards, due to gap in
SPL flow unable to load PMU config object.
Signed-off-by: Jaewon Lee <jaewon.lee@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
The ZCU106 Evaluation Kit enables designers to jumpstart designs for
video conferencing, surveillance, Advanced Driver Assisted Systems
(ADAS) and streaming and encoding applications. This kit features a
Zynq® UltraScale+™ MPSoC EV device and supports all major peripherals
and interfaces, enabling development for a wide range of applications.
The included ZU7EV device is equipped with a quad-core ARM® Cortex™-A53
applications processor, dual-core Cortex-R5 real-time processor,
Mali™-400 MP2 graphics processing unit, 4KP60 capable H.264/H.265 video
codec, and 16nm FinFET+ programmable logic.
This patch adds machine configuration file for ZCU106 Evaluation Kit
with required setting of board specific yocto variables needed for
compilation of bootloader, kernel and device-tree.
- linux-xlnx is the kernel provider
- u-boot-xlnx is the u-boot provider which will also generate SPL boot.bin
- hwcodec is provided by libomxil-xlnx recipe, this will pull in
additional dependencies of VCU kernel modules, control software,
firmware binaries
Depending on the application need you may want to pass the appropriate
CMA size in bootargs or set CONFIG_CMA_SIZE_MBYTES in kernel.
While using SPL flow, you may need to provide additional hack to pass
the PMU config object. This is similar to all ZU+ boards, due to gap in
SPL flow unable to load PMU config object.
Signed-off-by: Devarsh Thakkar <devarsht@xilinx.com>
Tested-by: Maulik Desai <maulik.desai@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add LAYERSERIES_COMPAT for sumo release
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add LAYERSERIES_COMPAT for sumo release
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Due to this change 54e2729ed43f82b8cfd96395fb68e447a9b60f86, zcu102
runqemu does not depend on u-boot-spl.bin. It requires just ATF and
u-boot to be present. Hence deploying of u-boot-spl.bin is no longer
required.
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Update kc705 bitstream for 2018.1 release
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add the wiring in u-boot-xlnx to compile kc705-microblazeel machine.
Tested-by: Jaewon Lee <jaewon.lee@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
kc705 is tested with Xilinx kernel tree and u-boot, set preferred
provider to use the vendor tree rather than upstream version
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Due to changes in 1138c5623d3e0c415d18b109ccf6c4f301c173f6, the
definiton of UBOOT_MACHINE was removed. This causes the following error
ERROR: Nothing PROVIDES 'virtual/bootloader'
u-boot-xlnx PROVIDES virtual/bootloader but was skipped: Either
UBOOT_MACHINE or UBOOT_CONFIG must be set in the kc705-microblazeel
machine configuration.
u-boot PROVIDES virtual/bootloader but was skipped: Either UBOOT_MACHINE
or UBOOT_CONFIG must be set in the kc705-microblazeel machine
configuration.
u-boot-xlnx-dev PROVIDES virtual/bootloader but was skipped: Either
UBOOT_MACHINE or UBOOT_CONFIG must be set in the kc705-microblazeel
machine configuration.
This is a requried setting, set it to microblaze-generic_config
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2).
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
A race issue can be induced by do_zynq_platform_init() being fired
before do_unpack(), resulting in
| DEBUG: Executing shell function do_zynq_platform_init
| cp: cannot create regular file '.../git/board/xilinx/zynq/': No such file or directory
| WARNING: exit code 1 from a shell command.
Mitigate issue by adding dependency to completion of do_unpack task
for custom do_zynq_platform_init task. Also update comment on previous
line to match the actions on next.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
Reviewed-by: Alejandro Enedino Hernandez Samaniego <alejandr@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
software libraries for VCU
Add new recipes for the following:
vcu-firmware_git.bb: Add a new recipe to fetch the required firmware
binaries for VCU
kernel-module-vcu_git.bb: Add new recipe for out-of-tree kernel module
required for VCU decoder, encoder. This is applicable to MPSoC EV
devices which support Video Codec Unit
libvcu-xlnx_git.bb: Add a new recipe for control software libraries,
test applications and headers for VCU
libomxil-xlnx_git.bb: Add VCU hwcodec, this contain the OpenMAX
libraries, test applications and headers for VCU
Signed-off-by: Devarsh Thakkar <devarsht@xilinx.com>
Signed-off-by: Jeegar Patel <jeegar.patel@xilinx.com>
Tested-by: Maulik Desai <maulik.desai@xilinx.com>
Acked-by: Varunkumar Allagadapa <varunkum@xilinx.com>
Reviewed-by: Bhargava Sreekantappa Gayathri <bhargava.sreekantappa-gayathri@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
This patch updates xilinx drm driver name to "xlnx"
Signed-off-by: Varunkumar Allagadapa <varunkum@xilinx.com>
Signed-off-by: Bhargava Sreekantappa Gayathri<bhargava.sreekantappa-gayathri@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
This patch will update Mali kernel driver to r8p0-01rel0.
Signed-off-by: Madhurkiran Harikrishnan <madhurki@xilinx.com>
Tested-by: Jaewon Lee <jaewon.lee@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
There are instances when SPL can be completely disabled, in such cases
do_deploy will error out complaining u-boot-spl.bin not found. This
patch fixes the issue by deploying u-boot-spl.bin only if it is present
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Use ATF and u-boot.elf while booting using QEMU instead of
u-boot-spl.bin. The ATF code is fixed not to fail while looking for
FSBL. Also adopt to using pmu-firmware-${MACHINE} name change
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Update to 2018.1 pmu firmware
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Upgrade to major release 3.0.0
- License changes: Added Embedded brains, but license type stayed
the same.
- Newlib dropped support for Kernighan & Ritchie C
- We can avoid building using full gcc and use gcc-initial instead.
Signed-off-by: Alejandro Enedino Hernandez Samaniego <alejandr@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
oe-core has upgraded binutils to v2.30, which caused some of our patches
to fail, rebase these along with other minimal changes to avoid these
errors and provide compatibility with latest oe-core.
Signed-off-by: Alejandro Enedino Hernandez Samaniego <alejandr@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Rework existing patches to 2018.1 Xilinx kernel recipe
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Update the arm-trusted-firmware, u-boot-xlnx, linux-xlnx,
qemu-xilinx and qemu-devicetrees recipes for 2018.1 release
Tested-by: Jaewon Lee <jaewon.lee@xilinx.com>
Acked-by: Bhargava Sreekantappa Gayathri <bhargava.sreekantappa-gayathri@xilinx.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Remove 2017.3 based component recipes
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
|
|
Update the local patch for the shadow ident fix with the patch that was
accepted upstream. This patch is not in a current GCC release yet, but
will be available in v8.x when released.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add provider virtual/dtb as this recipe is involved in building dtb from
dts. We can add other recipes or conf to depend on virtual/dtb whenever
required
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add the wiring in u-boot-xlnx to compile kc705-microblazeel machine.
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
If xen is present in distro enable xen modules to be built while
building linux-xlnx kernel.
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Make linux-xlnx recipe applicable to all MB machines, remove the
restriction of applying it only to kc705
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add PV with Xilinx release version and u-boot version. This follows on
similar lines on how we handle kernel recipe
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add PV with Xilinx release version and ATF version. This follows on
similar lines on how we handle kernel recipe
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add all the Xilinx patches for MicroBlaze, this includes a number of
bug fixes, testsuite fixes, feature improvements and additional feature
support.
Important changes:
* v10.0 - CPU support
* v10.0 - Bit-field instruction support
* v10.0 - 8-stage pipeline aka 'frequency' optimized
* Size optimized implementations for shift instructions
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
Add all the Xilinx patches for MicroBlaze, this includes bug fixes,
testsuite fixes (and workarounds) as well as additional features.
A number of these changes are required to support additional Xilinx
patches for MicroBlaze GCC.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
This patch is required to remove circular depedency while compiling
kernel image simpleImage.mb for MB machines. We need the task to be
depedent on do_configure because kernel will depend on device-tree
to be available while compiling simpleImage.mb.
The kernel source is available in work-shared/kernel-source after
do_configure task is run, this patch changes the depedency from
do_shared_workdir to do_configure.
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
The MicroBlaze tunes are now part of oe-core. This removes the need for
the meta-xilinx-bsp layer to provide architecture tunes.
The tunes in oe-core are almost identical (with the exception of
tune-microblaze.inc which had machine configuration in meta-xilinx).
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
With the perspective removal of tune-microblaze.inc, the following
preferred GDB version configuration for MicroBlaze needs to be
relocated.
This change also drops the setting of gdb-cross* targets as they were
not setup properly since "gdb-cross-${TARGET_ARCH}" was not specified
correctly. This is also preferred as newer GDB (e.g. 8.0) does support
gdb-cross for debugging (just not gdbserver/gdb).
Ideally the MicroBlaze GDB patches should be updated to support the
newest GDB and or upstreamed. However this setup continues to be
available until that occurs.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
The tune-microblaze.inc is currently providing this configuration,
however since this is not a tune specific configuration it should be set
by the machine itself. Additionally with the perspective change to
remove tune-microblaze.inc the reliance on this includes configuration
needs to be removed.
Also remove the superfluous '_remove = "device-tree"' for
s3adsp1800-qemu-microblazeeb.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|
|
With prelink-rtld support available for MicroBlaze and toolchain fixes
for atomic CAS bugs it is functional to generate gobject introspection
data for MicroBlaze binaries. This does still require the meta-xilinx
append for qemu which enables the architecture such that qemu linux user
is available.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com>
|