| Age | Commit message (Collapse) | Author |
|---|
|
commit d8dd25a461e4eec7190cb9d66616aceacc5110ad upstream.
When the current frame address (CFA) is stored on the stack (i.e.,
cfa->base == CFI_SP_INDIRECT), objtool neglects to adjust the stack
offset when there are subsequent pushes or pops. This results in bad
ORC data at the end of the ENTER_IRQ_STACK macro, when it puts the
previous stack pointer on the stack and does a subsequent push.
This fixes the following unwinder warning:
WARNING: can't dereference registers at 00000000f0a6bdba for ip interrupt_entry+0x9f/0xa0
Fixes: 627fce14809b ("objtool: Add ORC unwind table generation")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Reported-by: Dave Jones <dsj@fb.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Reported-by: Joe Mario <jmario@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/853d5d691b29e250333332f09b8e27410b2d9924.1587808742.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b87080eab4c1377706c113fc9c0157f19ea8fed1 ]
After successfully running the IPC msgque test once, subsequent runs
result in a test failure:
$ sudo ./run_kselftest.sh
TAP version 13
1..1
# selftests: ipc: msgque
# Failed to get stats for IPC queue with id 0
# Failed to dump queue: -22
# Bail out!
# # Pass 0 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
not ok 1 selftests: ipc: msgque # exit=1
The dump_queue() function loops through the possible message queue index
values using calls to msgctl(kern_id, MSG_STAT, ...) where kern_id
represents the index value. The first time the test is ran, the initial
index value of 0 is valid and the test is able to complete. The index
value of 0 is not valid in subsequent test runs and the loop attempts to
try index values of 1, 2, 3, and so on until a valid index value is
found that corresponds to the message queue created earlier in the test.
The msgctl() syscall returns -1 and sets errno to EINVAL when invalid
index values are used. The test failure is caused by incorrectly
comparing errno to -EINVAL when cycling through possible index values.
Fix invalid test failures on subsequent runs of the msgque test by
correctly comparing errno values to a non-negated EINVAL.
Fixes: 3a665531a3b7 ("selftests: IPC message queue copy feature test")
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8782e7cab51b6bf01a5a86471dd82228af1ac185 ]
Historically, the relocation symbols for ORC entries have only been
section symbols:
.text+0: sp:sp+8 bp:(und) type:call end:0
However, the Clang assembler is aggressive about stripping section
symbols. In that case we will need to use function symbols:
freezing_slow_path+0: sp:sp+8 bp:(und) type:call end:0
In preparation for the generation of such entries in "objtool orc
generate", add support for reading them in "objtool orc dump".
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/b811b5eb1a42602c3b523576dc5efab9ad1c174d.1585761021.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd841d6154f5f41f8a32d3c1b0bc229e326e640a ]
CONFIG_UBSAN_TRAP causes GCC to emit a UD2 whenever it encounters an
unreachable code path. This includes __builtin_unreachable(). Because
the BUG() macro uses __builtin_unreachable() after it emits its own UD2,
this results in a double UD2. In this case objtool rightfully detects
that the second UD2 is unreachable:
init/main.o: warning: objtool: repair_env_string()+0x1c8: unreachable instruction
We weren't able to figure out a way to get rid of the double UD2s, so
just silence the warning.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/6653ad73c6b59c049211bd7c11ed3809c20ee9f5.1585761021.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cf01699ee220c38099eb3e43ce3d10690c8b7060 upstream.
Commit 7ed1c1901fe5 ("tools: fix cross-compile var clobbering") moved
the setup of the CC variable to tools/scripts/Makefile.include to make
the behavior consistent across all the tools Makefiles.
As the vm tools missed the include we end up with the wrong CC in a
cross-compiling evironment.
Fixes: 7ed1c1901fe5 (tools: fix cross-compile var clobbering)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Kelly <martin@martingkelly.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200416104748.25243-1-l.stach@pengutronix.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b43e78f65b1d35fd3e13c7b23f9b64ea83c9ad3a ]
As the ftrace selftests can run for a long period of time, disable the
timeout that the general selftests have. If a selftest hangs, then it
probably means the machine will hang too.
Link: https://lore.kernel.org/r/alpine.LSU.2.21.1911131604170.18679@pobox.suse.cz
Suggested-by: Miroslav Benes <mbenes@suse.cz>
Tested-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d573a07528308eb77ec072c010819c359bebf6e ]
get_test_count() and get_test_enabled() were broken for test numbers
above 9 due to awk interpreting a field specification like '$0010' as
octal rather than decimal. Fix it by stripping the leading zeroes.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: NeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20200318230515.171692-5-ebiggers@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 555089fdfc37ad65e0ee9b42ca40c238ff546f83 upstream.
For plain text output, it incorrectly prints the pointer value
"void *data". The "void *data" is actually pointing to memory that
contains a bpf-map's value. The intention is to print the content of
the bpf-map's value instead of printing the pointer pointing to the
bpf-map's value.
In this case, a member of the bpf-map's value is a pointer type.
Thus, it should print the "*(void **)data".
Fixes: 22c349e8db89 ("tools: bpftool: fix format strings and arguments for jsonw_printf()")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Link: https://lore.kernel.org/bpf/20200110231644.3484151-1-kafai@fb.com
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b401efc120a399dfda1f4d2858a4de365c9b08ef upstream.
If a switch jump table's indirect branch is in a ".cold" subfunction in
.text.unlikely, objtool doesn't detect it, and instead prints a false
warning:
drivers/media/v4l2-core/v4l2-ioctl.o: warning: objtool: v4l_print_format.cold()+0xd6: sibling call from callable instruction with modified stack frame
drivers/hwmon/max6650.o: warning: objtool: max6650_probe.cold()+0xa5: sibling call from callable instruction with modified stack frame
drivers/media/dvb-frontends/drxk_hard.o: warning: objtool: init_drxk.cold()+0x16f: sibling call from callable instruction with modified stack frame
Fix it by comparing the function, instead of the section and offset.
Fixes: 13810435b9a7 ("objtool: Support GCC 8's cold subfunctions")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/157c35d42ca9b6354bbb1604fe9ad7d1153ccb21.1585761021.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9c9ce4e598e012ca7c1813fae2f4d02395807de upstream.
Python 3.8 changed the output of 'python-config --ldflags' to no longer
include the '-lpythonX.Y' flag (this apparently fixed an issue loading
modules with a statically linked Python executable). The libpython
feature check in linux/build/feature fails if the Python library is not
included in FEATURE_CHECK_LDFLAGS-libpython variable.
This adds a check in the Makefile to determine if PYTHON_CONFIG accepts
the '--embed' flag and passes that flag alongside '--ldflags' if so.
tools/perf is the only place the libpython feature check is used.
Signed-off-by: Sam Lunt <samuel.j.lunt@gmail.com>
Tested-by: He Zhe <zhe.he@windriver.com>
Link: http://lore.kernel.org/lkml/c56be2e1-8111-9dfe-8298-f7d0f9ab7431@windriver.com
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: trivial@kernel.org
Cc: stable@kernel.org
Link: http://lore.kernel.org/lkml/20200131181123.tmamivhq4b7uqasr@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eea274d64e6ea8aff2224d33d0851133a84cc7b5 upstream.
It was noticed that mlock2 tests are failing after 9c4e6b1a7027f ("mm,
mlock, vmscan: no more skipping pagevecs") because the patch has changed
the timing on when the page is added to the unevictable LRU list and thus
gains the unevictable page flag.
The test was just too dependent on the implementation details which were
true at the time when it was introduced. Page flags and the timing when
they are set is something no userspace should ever depend on. The test
should be testing only for the user observable contract of the tested
syscalls. Those are defined pretty well for the mlock and there are other
means for testing them. In fact this is already done and testing for page
flags can be safely dropped to achieve the aimed purpose. Present bits
can be checked by /proc/<pid>/smaps RSS field and the locking state by
VmFlags although I would argue that Locked: field would be more
appropriate.
Drop all the page flag machinery and considerably simplify the test. This
should be more robust for future kernel changes while checking the
promised contract is still valid.
Fixes: 9c4e6b1a7027f ("mm, mlock, vmscan: no more skipping pagevecs")
Reported-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Eric B Munson <emunson@akamai.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200324154218.GS19542@dhcp22.suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82f04bfe2aff428b063eefd234679b2d693228ed upstream.
Commit 0161a94e2d1c7 ("tools: gpio: Correctly add make dependencies for
gpio_utils") added a make rule for gpio-utils-in.o but used $(output)
instead of the correct $(OUTPUT) for the output directory, breaking
out-of-tree build (O=xx) with the following error:
No rule to make target 'out/tools/gpio/gpio-utils-in.o', needed by 'out/tools/gpio/lsgpio-in.o'. Stop.
Fix that.
Fixes: 0161a94e2d1c ("tools: gpio: Correctly add make dependencies for gpio_utils")
Cc: <stable@vger.kernel.org>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20200325103154.32235-1-anssi.hannula@bitwise.fi
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 630b99ab60aa972052a4202a1ff96c7e45eb0054 ]
If AT_SYSINFO is not present, don't try to call a NULL pointer.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/faaf688265a7e1a5b944d6f8bc0f6368158306d3.1584052409.git.luto@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4054ab64e29bb05b3dfe758fff3c38a74ba753bb upstream.
A recent change to the netlink code: 6e237d099fac ("netlink: Relax attr
validation for fixed length types") logs a warning when programs send
messages with invalid attributes (e.g., wrong length for a u32). Yafang
reported this error message for tools/accounting/getdelays.c.
send_cmd() is wrongly adding 1 to the attribute length. As noted in
include/uapi/linux/netlink.h nla_len should be NLA_HDRLEN + payload
length, so drop the +1.
Fixes: 9e06d3f9f6b1 ("per task delay accounting taskstats interface: documentation fix")
Reported-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Yafang Shao <laoar.shao@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Shailabh Nagar <nagar@watson.ibm.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200327173111.63922-1-dsahern@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1f81c5efc020314b2db30d77efe228b7e117750d ]
Some Chromebook BIOS' do not export an ACPI LPIT, which is how
Linux finds the residency counter for CPU and SYSTEM low power states,
that is exports in /sys/devices/system/cpu/cpuidle/*residency_us
When these sysfs attributes are missing, check the debugfs attrubte
from the pmc_core driver, which accesses the same counter value.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8d005ba6afa502ca37ced5782f672c4d2fc1515 ]
Warning: ‘__builtin_strncpy’ specified bound 20 equals destination size
[-Wstringop-truncation]
reduce param to strncpy, to guarantee that a null byte is always copied
into destination buffer.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit db2c549407d4a76563c579e4768f7d6d32afefba upstream.
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries")
Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Keeping <john@metanate.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Lentine <mlentine@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be40920fbf1003c38ccdc02b571e01a75d890c82 upstream.
When I tried to compile tools/perf from the top directory with the -C
option, the O= option didn't work correctly if I passed a relative path:
$ make O=BUILD -C tools/perf/
make: Entering directory '/home/mhiramat/ksrc/linux/tools/perf'
BUILD: Doing 'make -j8' parallel build
../scripts/Makefile.include:4: *** O=/home/mhiramat/ksrc/linux/tools/perf/BUILD does not exist. Stop.
make: *** [Makefile:70: all] Error 2
make: Leaving directory '/home/mhiramat/ksrc/linux/tools/perf'
The O= directory existence check failed because the check script ran in
the build target directory instead of the directory where I ran the make
command.
To fix that, once change directory to $(PWD) and check O= directory,
since the PWD is set to where the make command runs.
Fixes: c883122acc0d ("perf tools: Let O= makes handle relative paths")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158351957799.3363.15269768530697526765.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1efde2754275dbd9d11c6e0132a4f09facf297ab upstream.
Do not depend on dwfl_module_addrsym() because it can fail on user-space
shared libraries.
Actually, same bug was fixed by commit 664fee3dc379 ("perf probe: Do not
use dwfl_module_addrsym if dwarf_diename finds symbol name"), but commit
07d369857808 ("perf probe: Fix wrong address verification) reverted to
get actual symbol address from symtab.
This fixes it again by getting symbol address from DIE, and only if the
DIE has only address range, it uses dwfl_module_addrsym().
Fixes: 07d369857808 ("perf probe: Fix wrong address verification)
Reported-by: Alexandre Ghiti <alex@ghiti.fr>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Alexandre Ghiti <alex@ghiti.fr>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sashal@kernel.org>
Link: http://lore.kernel.org/lkml/158281812176.476.14164573830975116234.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2de7fb60a4740135e03cf55c1982e393ccb87b6b ]
Building cpupower with -fno-common in CFLAGS results in errors due to
multiple definitions of the 'cpu_count' and 'start_time' variables.
./utils/idle_monitor/snb_idle.o:./utils/idle_monitor/cpupower-monitor.h:28:
multiple definition of `cpu_count';
./utils/idle_monitor/nhm_idle.o:./utils/idle_monitor/cpupower-monitor.h:28:
first defined here
...
./utils/idle_monitor/cpuidle_sysfs.o:./utils/idle_monitor/cpuidle_sysfs.c:22:
multiple definition of `start_time';
./utils/idle_monitor/amd_fam14h_idle.o:./utils/idle_monitor/amd_fam14h_idle.c:85:
first defined here
The -fno-common option will be enabled by default in GCC 10.
Bug: https://bugs.gentoo.org/707462
Signed-off-by: Mike Gilbert <floppym@gentoo.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f649bd9dd5d5004543bbc3c50b829577b49f5d75 upstream.
Since commit 3b2323c2c1c4 ("perf bench futex: Use cpumaps") the default
number of threads the benchmark uses got changed from number of online
CPUs to zero:
$ perf bench futex wake
# Running 'futex/wake' benchmark:
Run summary [PID 15930]: blocking on 0 threads (at [private] futex 0x558b8ee4bfac), waking up 1 at a time.
[Run 1]: Wokeup 0 of 0 threads in 0.0000 ms
[...]
[Run 10]: Wokeup 0 of 0 threads in 0.0000 ms
Wokeup 0 of 0 threads in 0.0004 ms (+-40.82%)
Restore the old behavior by grabbing the number of online CPUs via
cpu->nr:
$ perf bench futex wake
# Running 'futex/wake' benchmark:
Run summary [PID 18356]: blocking on 8 threads (at [private] futex 0xb3e62c), waking up 1 at a time.
[Run 1]: Wokeup 8 of 8 threads in 0.0260 ms
[...]
[Run 10]: Wokeup 8 of 8 threads in 0.0270 ms
Wokeup 8 of 8 threads in 0.0419 ms (+-24.35%)
Fixes: 3b2323c2c1c4 ("perf bench futex: Use cpumaps")
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lore.kernel.org/lkml/20200305083714.9381-3-tommi.t.rantala@nokia.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d00fc477a2ce8b6d2b09fb34ef9fe9918e7d434 upstream.
Before rebooting the box, a "ssh sync" is called to the test machine to see
if it is alive or not. But if the test machine is in a partial state, that
ssh may never actually finish, and the ktest test hangs.
Add a 10 second timeout to the sync test, which will fail after 10 seconds
and then cause the test to reboot the test machine.
Cc: stable@vger.kernel.org
Fixes: 6474ace999edd ("ktest.pl: Powercycle the box on reboot if no connection can be made")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0d29169a708bf730ede287248e429d579f432d1d ]
This patch update {ipv4, ipv6}_addr_metric_test with
1. Set metric of address with peer route and see if the route added
correctly.
2. Modify metric and peer address for peer route and see if the route
changed correctly.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e8023b030ce1748930e2dc76353a262fe47d4745 ]
For tc ip_proto filter, when we extract the flow via __skb_flow_dissect()
without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to
the inner proto.
So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP
proto.
For test mirror_gre.sh, it may make user confused if we capture ICMP
message on $h3(since the flow is GRE message). So I move the capture
dev to h3-gt{4,6}, and only capture ICMP message.
Before the fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
After fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
Fixes: ba8d39871a10 ("selftests: forwarding: Add test for mirror to gretap")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <pmachata@gmail.com>
Tested-by: Petr Machata <pmachata@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c363eb48ada5cf732b3f489fab799fc881097842 ]
With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:
make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127
Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)
Also, separate handling of each of the lists to its own shell command.
The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Tested-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3f7774033e6820d25beee5cf7aefa11d4968b951 upstream.
We need to set actions->ms.map since 599a2f38a989 ("perf hists browser:
Check sort keys before hot key actions"), as in that patch we bail out
if map is NULL.
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 599a2f38a989 ("perf hists browser: Check sort keys before hot key actions")
Link: https://lkml.kernel.org/n/tip-wp1ssoewy6zihwwexqpohv0j@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57ddf09173c1e7d0511ead8924675c7198e56545 upstream.
Commit 0aa802a79469 ("perf stat: Get rid of extra clock display
function") introduced scale and unit for clock events. Thus,
perf_stat__update_shadow_stats() now saves scaled values of clock events
in msecs, instead of original nsecs. But while calculating values of
shadow stats we still consider clock event values in nsecs. This results
in a wrong shadow stat values. Ex,
# ./perf stat -e task-clock,cycles ls
<SNIP>
2.60 msec task-clock:u # 0.877 CPUs utilized
2,430,564 cycles:u # 1215282.000 GHz
Fix this by saving original nsec values for clock events in
perf_stat__update_shadow_stats(). After patch:
# ./perf stat -e task-clock,cycles ls
<SNIP>
3.14 msec task-clock:u # 0.839 CPUs utilized
3,094,528 cycles:u # 0.985 GHz
Suggested-by: Jiri Olsa <jolsa@redhat.com>
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: yuzhoujian@didichuxing.com
Fixes: 0aa802a79469 ("perf stat: Get rid of extra clock display function")
Link: http://lkml.kernel.org/r/20181116042843.24067-1-ravi.bangoria@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb08d006054e7e374592068919e32579988602d4 upstream.
We already have function to check if a given event is either
SW_CPU_CLOCK or SW_TASK_CLOCK. Utilize it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: yuzhoujian@didichuxing.com
Link: http://lkml.kernel.org/r/20181115095533.16930-1-ravi.bangoria@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e404b8c7cfb31654c9024d497cec58a501501692 ]
After commit 27596472473a ("ipv6: fix ECMP route replacement") it is no
longer possible to replace an ECMP-able route by a non ECMP-able route.
For example,
ip route add 2001:db8::1/128 via fe80::1 dev dummy0
ip route replace 2001:db8::1/128 dev dummy0
does not work as expected.
Tweak the replacement logic so that point 3 in the log of the above commit
becomes:
3. If the new route is not ECMP-able, and no matching non-ECMP-able route
exists, replace matching ECMP-able route (if any) or add the new route.
We can now summarize the entire replace semantics to:
When doing a replace, prefer replacing a matching route of the same
"ECMP-able-ness" as the replace argument. If there is no such candidate,
fallback to the first route found.
Fixes: 27596472473a ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 51bad0f05616c43d6d34b0a19bcc9bdab8e8fb39 ]
Currently, there is a lot of false positives if a single reuseport test
fails. This is because expected_results and the result map are not cleared.
Zero both after individual test runs, which fixes the mentioned false
positives.
Fixes: 91134d849a0e ("bpf: Test BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200124112754.19664-5-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b7e20a7ba54836076ff35a28349dabea4cec48f ]
Add TEST opcode to Group3-2 reg=001b as same as Group3-1 does.
Commit
12a78d43de76 ("x86/decoder: Add new TEST instruction pattern")
added a TEST opcode assignment to f6 XX/001/XXX (Group 3-1), but did
not add f7 XX/001/XXX (Group 3-2).
Actually, this TEST opcode variant (ModRM.reg /1) is not described in
the Intel SDM Vol2 but in AMD64 Architecture Programmer's Manual Vol.3,
Appendix A.2 Table A-6. ModRM.reg Extensions for the Primary Opcode Map.
Without this fix, Randy found a warning by insn_decoder_test related
to this issue as below.
HOSTCC arch/x86/tools/insn_decoder_test
HOSTCC arch/x86/tools/insn_sanity
TEST posttest
arch/x86/tools/insn_decoder_test: warning: Found an x86 instruction decoder bug, please report this.
arch/x86/tools/insn_decoder_test: warning: ffffffff81000bf1: f7 0b 00 01 08 00 testl $0x80100,(%rbx)
arch/x86/tools/insn_decoder_test: warning: objdump says 6 bytes, but insn_get_length() says 2
arch/x86/tools/insn_decoder_test: warning: Decoded and checked 11913894 instructions with 1 failures
TEST posttest
arch/x86/tools/insn_sanity: Success: decoded and checked 1000000 random instructions with 0 errors (seed:0x871ce29c)
To fix this error, add the TEST opcode according to AMD64 APM Vol.3.
[ bp: Massage commit message. ]
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lkml.kernel.org/r/157966631413.9580.10311036595431878351.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 585c91f40d201bc564d4e76b83c05b3b5363fe7e ]
Fix unsafe unaligned pointer usage in usbip network interfaces. usbip tool
build fails with new gcc -Werror=address-of-packed-member checks.
usbip_network.c: In function ‘usbip_net_pack_usb_device’:
usbip_network.c:79:32: error: taking address of packed member of ‘struct usbip_usb_device’ may result in an unaligned pointer value [-Werror=address-of-packed-member]
79 | usbip_net_pack_uint32_t(pack, &udev->busnum);
Fix with minor changes to pass by value instead of by address.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200109012416.2875-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6794200fa3c9c3e6759dae099145f23e4310f4f7 ]
GCC9 introduced string hardening mechanisms, which exhibits the error
during fs api compilation:
error: '__builtin_strncpy' specified bound 4096 equals destination size
[-Werror=stringop-truncation]
This comes when the length of copy passed to strncpy is is equal to
destination size, which could potentially lead to buffer overflow.
There is a need to mitigate this potential issue by limiting the size of
destination by 1 and explicitly terminate the destination with NULL.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lore.kernel.org/lkml/20191211080109.18765-1-andrey.zhizhikin@leica-geosystems.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b64a650f0b2ae3940698f401732988699eecf7a ]
It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest. This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function. The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries. Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.
On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.
Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.
To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function. The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.
[1] https://bugs.linaro.org/show_bug.cgi?id=5479
Signed-off-by: Siddhesh Poyarekar <siddhesh@gotplt.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1985f8c7f9a42a651a9750d6fcadc74336d182df upstream.
If we compile tools/acpi target in the top source directory, we'd get a
compilation error showing as bellow:
# make tools/acpi
DESCEND power/acpi
DESCEND tools/acpidbg
CC tools/acpidbg/acpidbg.o
Assembler messages:
Fatal error: can't create /home/lzy/kernel-upstream/power/acpi/\
tools/acpidbg/acpidbg.o: No such file or directory
../../Makefile.rules:26: recipe for target '/home/lzy/kernel-upstream/\
power/acpi/tools/acpidbg/acpidbg.o' failed
make[3]: *** [/home/lzy/kernel-upstream//power/acpi/tools/acpidbg/\
acpidbg.o] Error 1
Makefile:19: recipe for target 'acpidbg' failed
make[2]: *** [acpidbg] Error 2
Makefile:54: recipe for target 'acpi' failed
make[1]: *** [acpi] Error 2
Makefile:1607: recipe for target 'tools/acpi' failed
make: *** [tools/acpi] Error 2
Fixes: d5a4b1a540b8 ("tools/power/acpi: Remove direct kernel source include reference")
Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fcf3a55a62afb0760ccb6f391d62f20bce4a42f upstream.
The filter name is fixed to "exit_reason" for some kvm_exit events, no
matter what architect we have. Actually, the filter name ("exit_reason")
is only applicable to x86, meaning it's broken on other architects
including aarch64.
This fixes the issue by providing various kvm_exit filter names, depending
on architect we're on. Afterwards, the variable filter name is picked and
applied through ioctl(fd, SET_FILTER).
Reported-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c3314a74f86dc00827e0945c8e5039fc3aebaa3c ]
Commit 800d3f561659 ("perf report: Add warning when libunwind not
compiled in") breaks the s390 platform. S390 uses libdw-dwarf-unwind for
call chain unwinding and had no support for libunwind.
So the warning "Please install libunwind development packages during the
perf build." caused the confusion even if the call-graph is displayed
correctly.
This patch adds checking for HAVE_DWARF_SUPPORT, which is set when
libdw-dwarf-unwind is compiled in.
Fixes: 800d3f561659 ("perf report: Add warning when libunwind not compiled in")
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Reviewed-by: Thomas Richter <tmricht@linux.ibm.com>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200107191745.18415-1-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f84ae29a6169318f9c929720c49d96323d2bbab9 ]
It is necessary to call free_arg(arg) when add_filter_type() returns NULL
in filter_event().
Signed-off-by: Hewenliang <hewenliang4@huawei.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Link: http://lore.kernel.org/lkml/20191209063549.59941-1-hewenliang4@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6c4798d3f08b81c2c52936b10e0fa872590c96ae upstream.
Disable a couple of compilation warnings (which are treated as errors)
on strlcpy() definition and declaration, allowing users to compile perf
and kernel (objtool) when:
1. glibc have strlcpy() (such as in ALT Linux since 2004) objtool and
perf build fails with this (in gcc):
In file included from exec-cmd.c:3:
tools/include/linux/string.h:20:15: error: redundant redeclaration of ‘strlcpy’ [-Werror=redundant-decls]
20 | extern size_t strlcpy(char *dest, const char *src, size_t size);
2. clang ignores `-Wredundant-decls', but produces another warning when
building perf:
CC util/string.o
../lib/string.c:99:8: error: attribute declaration must precede definition [-Werror,-Wignored-attributes]
size_t __weak strlcpy(char *dest, const char *src, size_t size)
../../tools/include/linux/compiler.h:66:34: note: expanded from macro '__weak'
# define __weak __attribute__((weak))
/usr/include/bits/string_fortified.h:151:8: note: previous definition is here
__NTH (strlcpy (char *__restrict __dest, const char *__restrict __src,
Committer notes:
The
#pragma GCC diagnostic
directive was introduced in gcc 4.6, so check for that as well.
Fixes: ce99091 ("perf tools: Move strlcpy() from perf to tools/lib/string.c")
Fixes: 0215d59 ("tools lib: Reinstate strlcpy() header guard with __UCLIBC__")
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=118481
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Dmitry Levin <ldv@altlinux.org>
Cc: Dmitry Levin <ldv@altlinux.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: kbuild test robot <lkp@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: Vineet Gupta <vineet.gupta1@synopsys.com>
Link: http://lore.kernel.org/lkml/20191224172029.19690-1-vt@altlinux.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1c8013ec34d7163431d18367808ea40b2e305f8 upstream.
Commit 722ddfde366f ("perf tools: Fix time sorting") changed - correctly
so - hist_entry__sort to return int64. Unfortunately several of the
builtin-c2c.c comparison routines only happened to work due the cast
caused by the wrong return type.
This causes meaningless ordering of both the cacheline list, and the
cacheline details page. E.g a simple:
perf c2c record -a sleep 3
perf c2c report
will result in cacheline table like
=================================================
Shared Data Cache Line Table
=================================================
#
# ------- Cacheline ---------- Total Tot - LLC Load Hitm - - Store Reference - - Load Dram - LLC Total - Core Load Hit - - LLC Load Hit -
# Index Address Node PA cnt records Hitm Total Lcl Rmt Total L1Hit L1Miss Lcl Rmt Ld Miss Loads FB L1 L2 Llc Rmt
# ..... .............. .... ...... ....... ...... ..... ..... ... .... ..... ...... ...... .... ...... ..... ..... ..... ... .... .......
0 0x7f0d27ffba00 N/A 0 52 0.12% 13 6 7 12 12 0 0 7 14 40 4 16 0 0 0
1 0x7f0d27ff61c0 N/A 0 6353 14.04% 1475 801 674 779 779 0 0 718 1392 5574 1299 1967 0 115 0
2 0x7f0d26d3ec80 N/A 0 71 0.15% 16 4 12 13 13 0 0 12 24 58 1 20 0 9 0
3 0x7f0d26d3ec00 N/A 0 98 0.22% 23 17 6 19 19 0 0 6 12 79 0 40 0 10 0
i.e. with the list not being ordered by Total Hitm.
Fixes: 722ddfde366f ("perf tools: Fix time sorting")
Signed-off-by: Andres Freund <andres@anarazel.de>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org # v3.16+
Link: http://lore.kernel.org/lkml/20200109043030.233746-1-andres@anarazel.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 22c349e8db89df86804d3ba23cef037ccd44a8bf ]
There are some mismatches between format strings and arguments passed to
jsonw_printf() in the BTF dumper for bpftool, which seems harmless but
may result in warnings if the "__printf()" attribute is used correctly
for jsonw_printf(). Let's fix relevant format strings and type cast.
Fixes: b12d6ec09730 ("bpf: btf: add btf print functionality")
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9def249dc8409ffc1f5a1d7195f1c462f2b49c07 ]
The last argument passed to some calls to the p_err() functions is not
correct, it should be "*argv" instead of "**argv". This may lead to a
segmentation fault error if CPU IDs or indices from the command line
cannot be parsed correctly. Let's fix this.
Fixes: f412eed9dfde ("tools: bpftool: add simple perf event output reader")
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c6874f401e5a0caab3b6a0663169e1fb5e930bb ]
cgroup code tries to use argv[0] as the cgroup path,
but if it fails uses argv[1] to report errors.
Fixes: 5ccda64d38cc ("bpftool: implement cgroup bpf operations")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a147faa96f832f76e772b1e448e94ea84c774081 ]
This fixes the various compiler warnings when building the msgque
selftest. The primary change is using sys/msg.h instead of linux/msg.h
directly to gain the API declarations.
Fixes: 3a665531a3b7 ("selftests: IPC message queue copy feature test")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f068435d9bb2d825d59e3c101bc579f09315ee01 upstream.
At some point in the past we needed to make sure we would get the long
name of modules and not just what we get from /proc/modules, but that
need, as described in the cset that introduced the adjustment function:
Fixes: c03d5184f0e9 ("perf machine: Adjust dso->long_name for offline module")
Without using the buildid-cache:
# lsmod | grep trusted
# insmod trusted.ko
# lsmod | grep trusted
trusted 24576 0
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
probe:key_seal (on key_seal in trusted)
# perf probe -l
probe:key_seal (on key_seal in trusted)
#
No attempt at opening '[trusted]'.
Now using the build-id cache:
# rmmod trusted
# perf buildid-cache --add ./trusted.ko
# insmod trusted.ko
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
#
Again, no attempt at reading '[trusted]'.
Finally, adding a probe to that function and then using:
[root@quaco ~]# perf trace -e probe_perf:*/max-stack=16/ --max-events=2
0.000 perf/13456 probe_perf:dso__adjust_kmod_long_name(__probe_ip: 5492263)
dso__adjust_kmod_long_name (/home/acme/bin/perf)
machine__process_kernel_mmap_event (/home/acme/bin/perf)
machine__process_mmap_event (/home/acme/bin/perf)
perf_event__process_mmap (/home/acme/bin/perf)
machines__deliver_event (/home/acme/bin/perf)
perf_session__deliver_event (/home/acme/bin/perf)
perf_session__process_event (/home/acme/bin/perf)
process_simple (/home/acme/bin/perf)
reader__process_events (/home/acme/bin/perf)
__perf_session__process_events (/home/acme/bin/perf)
perf_session__process_events (/home/acme/bin/perf)
process_buildids (/home/acme/bin/perf)
record__finish_output (/home/acme/bin/perf)
__cmd_record (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
0.055 perf/13456 probe_perf:dso__adjust_kmod_long_name(__probe_ip: 5492263)
dso__adjust_kmod_long_name (/home/acme/bin/perf)
machine__process_kernel_mmap_event (/home/acme/bin/perf)
machine__process_mmap_event (/home/acme/bin/perf)
perf_event__process_mmap (/home/acme/bin/perf)
machines__deliver_event (/home/acme/bin/perf)
perf_session__deliver_event (/home/acme/bin/perf)
perf_session__process_event (/home/acme/bin/perf)
process_simple (/home/acme/bin/perf)
reader__process_events (/home/acme/bin/perf)
__perf_session__process_events (/home/acme/bin/perf)
perf_session__process_events (/home/acme/bin/perf)
process_buildids (/home/acme/bin/perf)
record__finish_output (/home/acme/bin/perf)
__cmd_record (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
#
This was the only path I could find using the perf tools that reach at this
function, then as of november/2019, if we put a probe in the line where the
actuall setting of the dso->long_name is done:
# perf trace -e probe_perf:*
^C[root@quaco ~]
# perf stat -e probe_perf:* -I 2000
2.000404265 0 probe_perf:dso__adjust_kmod_long_name
4.001142200 0 probe_perf:dso__adjust_kmod_long_name
6.001704120 0 probe_perf:dso__adjust_kmod_long_name
8.002398316 0 probe_perf:dso__adjust_kmod_long_name
10.002984010 0 probe_perf:dso__adjust_kmod_long_name
12.003597851 0 probe_perf:dso__adjust_kmod_long_name
14.004113303 0 probe_perf:dso__adjust_kmod_long_name
16.004582773 0 probe_perf:dso__adjust_kmod_long_name
18.005176373 0 probe_perf:dso__adjust_kmod_long_name
20.005801605 0 probe_perf:dso__adjust_kmod_long_name
22.006467540 0 probe_perf:dso__adjust_kmod_long_name
^C 23.683261941 0 probe_perf:dso__adjust_kmod_long_name
#
Its not being used at all.
To further test this I used kvm.ko as the offline module, i.e. removed
if from the buildid-cache by nuking it completely (rm -rf ~/.debug) and
moved it from the normal kernel distro path, removed the modules, stoped
the kvm guest, and then installed it manually, etc.
# rmmod kvm-intel
# rmmod kvm
# lsmod | grep kvm
# modprobe kvm-intel
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: could not insert 'kvm_intel': Unknown symbol in module, or unknown parameter (see dmesg)
# insmod ./kvm.ko
# modprobe kvm-intel
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
# lsmod | grep kvm
kvm_intel 299008 0
kvm 765952 1 kvm_intel
irqbypass 16384 1 kvm
#
# perf probe -x ~/bin/perf machine__findnew_module_map:12 mname=m.name:string filename=filename:string 'dso_long_name=map->dso->long_name:string' 'dso_name=map->dso->name:string'
# perf probe -l
probe_perf:machine__findnew_module_map (on machine__findnew_module_map:12@util/machine.c in /home/acme/bin/perf with mname filename dso_long_name dso_name)
# perf record
^C[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 3.416 MB perf.data (33956 samples) ]
# perf trace -e probe_perf:machine*
<SNIP>
6.322 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[salsa20_generic]", filename: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_long_name: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_name: "[salsa20_generic]")
6.375 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[kvm]", filename: "[kvm]", dso_long_name: "[kvm]", dso_name: "[kvm]")
<SNIP>
The filename doesn't come with the path, no point in trying to set the dso->long_name.
[root@quaco ~]# strace -e open,openat perf probe -m ./kvm.ko kvm_apic_local_deliver |& egrep 'open.*kvm'
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/kvm/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm", O_RDONLY|O_NONBLOCK|O_CLOEXEC|O_DIRECTORY) = 7
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 8
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/kvm.ko/5955f426cb93f03f30f3e876814be2db80ab0b55/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
[root@quaco ~]#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-jlfew3lyb24d58egrp0o72o2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07d369857808b7e8e471bbbbb0074a6718f89b31 upstream.
Since there are some DIE which has only ranges instead of the
combination of entrypc/highpc, address verification must use
dwarf_haspc() instead of dwarf_entrypc/dwarf_highpc.
Also, the ranges only DIE will have a partial code in different section
(e.g. unlikely code will be in text.unlikely as "FUNC.cold" symbol). In
that case, we can not use dwarf_entrypc() or die_entrypc(), because the
offset from original DIE can be a minus value.
Instead, this simply gets the symbol and offset from symtab.
Without this patch;
# perf probe -D clear_tasks_mm_cpumask:1
Failed to get entry address of clear_tasks_mm_cpumask
Error: Failed to add events.
And with this patch:
# perf probe -D clear_tasks_mm_cpumask:1
p:probe/clear_tasks_mm_cpumask clear_tasks_mm_cpumask+0
p:probe/clear_tasks_mm_cpumask_1 clear_tasks_mm_cpumask+5
p:probe/clear_tasks_mm_cpumask_2 clear_tasks_mm_cpumask+8
p:probe/clear_tasks_mm_cpumask_3 clear_tasks_mm_cpumask+16
p:probe/clear_tasks_mm_cpumask_4 clear_tasks_mm_cpumask+82
Committer testing:
I managed to reproduce the above:
[root@quaco ~]# perf probe -D clear_tasks_mm_cpumask:1
p:probe/clear_tasks_mm_cpumask _text+919968
p:probe/clear_tasks_mm_cpumask_1 _text+919973
p:probe/clear_tasks_mm_cpumask_2 _text+919976
[root@quaco ~]#
But then when trying to actually put the probe in place, it fails if I
use :0 as the offset:
[root@quaco ~]# perf probe -L clear_tasks_mm_cpumask | head -5
<clear_tasks_mm_cpumask@/usr/src/debug/kernel-5.2.fc30/linux-5.2.18-200.fc30.x86_64/kernel/cpu.c:0>
0 void clear_tasks_mm_cpumask(int cpu)
1 {
2 struct task_struct *p;
[root@quaco ~]# perf probe clear_tasks_mm_cpumask:0
Probe point 'clear_tasks_mm_cpumask' not found.
Error: Failed to add events.
[root@quaco
The next patch is needed to fix this case.
Fixes: 576b523721b7 ("perf probe: Fix probing symbols with optimization suffix")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157199318513.8075.10463906803299647907.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0feba17bd7ee3b7e03d141f119049dcc23efa94e upstream.
We observed an issue that was some extra columns displayed after switching
perf data file in browser. The steps to reproduce:
1. perf record -a -e cycles,instructions -- sleep 3
2. perf report --group
3. In browser, we use hotkey 's' to switch to another perf.data
4. Now in browser, the extra columns 'Self' and 'Children' are displayed.
The issue is setup_sorting() executed again after repeat path, so dimensions
are added again.
This patch checks the last key returned from __cmd_report(). If it's
K_SWITCH_INPUT_DATA, skips the setup_sorting().
Fixes: ad0de0971b7f ("perf report: Enable the runtime switching of perf data file")
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20191220013722.20592-1-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 55347ec340af401437680fd0e88df6739a967f9f upstream.
Variable names are inconsistent in hists__for_each macro().
Due to this inconsistency, the macro replaces its second argument with
"fmt" regardless of its original name.
So far it works because only "fmt" is passed to the second argument.
However, this behavior is not expected and should be fixed.
Fixes: f0786af536bb ("perf hists: Introduce hists__for_each_format macro")
Fixes: aa6f50af822a ("perf hists: Introduce hists__for_each_sort_list macro")
Signed-off-by: Yuya Fujita <fujita.yuya@fujitsu.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/OSAPR01MB1588E1C47AC22043175DE1B2E8520@OSAPR01MB1588.jpnprd01.prod.outlook.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit af9cb29c5488381083b0b5ccdfb3cd931063384a ]
As the rseq selftests can run for a long period of time, disable the
timeout that the general selftests have.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c65e41538b04e0d64a673828745a00cb68a24371 ]
firmware attempts to load test modules that require root access
and fail. Fix it to check for root uid and exit with skip code
instead.
Before this fix:
selftests: firmware: fw_run_tests.sh
modprobe: ERROR: could not insert 'test_firmware': Operation not permitted
You must have the following enabled in your kernel:
CONFIG_TEST_FIRMWARE=y
CONFIG_FW_LOADER=y
CONFIG_FW_LOADER_USER_HELPER=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
With this fix:
selftests: firmware: fw_run_tests.sh
skip all tests: must be run as root
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Reviwed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Josh Poimboeuf
Tyler Hicks
Lucas Stach
Steven Rostedt (VMware)
Eric Biggers
Martin KaFai Lau
Sam Lunt
Michal Hocko
Anssi Hannula
Andy Lutomirski
David Ahern
Len Brown
disconnect3d
Masami Hiramatsu
Mike Gilbert
Tommi Rantala
Hangbin Liu
Jiri Benc
Arnaldo Carvalho de Melo
Ravi Bangoria
Benjamin Poirier
Lorenz Bauer
Shuah Khan
Andrey Zhizhikin
Siddhesh Poyarekar
Zhengyuan Liu
Gavin Shan
Jin Yao
Hewenliang
Vitaly Chikunov
Andres Freund
Quentin Monnet
Jakub Kicinski
Kees Cook
Yuya Fujita
Mathieu Desnoyers