| Age | Commit message (Collapse) | Author |
|---|
|
operational
commit 3122257c02afd9f199a8fc84ae981e1fc4958532 upstream.
In emulated environments, the bridge ports enslaved to br1 get a carrier
before changing br1's PVID. This means that by the time the PVID is
changed, br1 is already operational and configured with an IPv6
link-local address.
When the test is run with netdevs registered by mlxsw, changing the PVID
is vetoed, as changing the VID associated with an existing L3 interface
is forbidden. This restriction is similar to the 8021q driver's
restriction of changing the VID of an existing interface.
Fix this by taking br1 down and bringing it back up when it is fully
configured.
With this fix, the test reliably passes on top of both the SW and HW
data paths (emulated or not).
Fixes: 239e754af854 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20220502084507.364774-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 71da1aec215290e249d09c44c768df859f3a3bba ]
The recent GRE selftests defined NUM_NETIFS=10. If the users copy
forwarding.config.sample to forwarding.config directly, they will get
error "Command line is not complete" when run the GRE tests, because
create_netif_veth() failed with no interface name defined.
Fix it by extending the NETIFS with p9 and p10.
Fixes: 2800f2485417 ("selftests: forwarding: Test multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8d0260cdd96fdccdef0509c4160e28a1012a5d7 ]
The FDB roaming test installs a destination MAC address on the wrong
interface of an FDB database and tests whether the mirroring fails, because
packets are sent to the wrong port. The test by mistake installs the FDB
entry as local. This worked previously, because drivers were notified of
local FDB entries in the same way as of static entries. However that has
been fixed in the commit 6ab4c3117aec ("net: bridge: don't notify switchdev
for local FDB addresses"), and local entries are not notified anymore. As a
result, the HW is not reconfigured for the FDB roam, and mirroring keeps
working, failing the test.
To fix the issue, mark the FDB entry as static.
Fixes: 9c7c8a82442c ("selftests: forwarding: mirror_gre_vlan_bridge_1q: Add more tests")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d2126838050ccd1dadf310ffb78b2204f3b032b9 ]
the following command:
# tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \
$tcflags dst_ip 192.0.2.2 ip_ttl 63 action drop
doesn't drop all IPv4 packets that match the configured TTL / destination
address. In particular, if "fragment offset" or "more fragments" have non
zero value in the IPv4 header, setting of FLOW_DISSECTOR_KEY_IP is simply
ignored. Fix this dissecting IPv4 TTL and TOS before fragment info; while
at it, add a selftest for tc flower's match on 'ip_ttl' that verifies the
correct behavior.
Fixes: 518d8a2e9bad ("net/flow_dissector: add support for dissection of misc ip header fields")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5aa3c334a449bab24519c4967f5ac2b3304c8dcf ]
The ECN bit defines ECT(1) = 1, ECT(0) = 2. So inner 0x02 + outer 0x01
should be inner ECT(0) + outer ECT(1). Based on the description of
__INET_ECN_decapsulate, the final decapsulate value should be
ECT(1). So fix the test expect value to 0x01.
Before the fix:
TEST: VXLAN: ECN decap: 01/02->0x02 [FAIL]
Expected to capture 10 packets, got 0.
After the fix:
TEST: VXLAN: ECN decap: 01/02->0x01 [ OK ]
Fixes: a0b61f3d8ebf ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit edcbf5137f093b5502f5f6b97cce3cbadbde27aa upstream.
When mirroring to a gretap in hardware the device expects to be
programmed with the egress port and all the encapsulating headers. This
requires the driver to resolve the path the packet will take in the
software data path and program the device accordingly.
If the path cannot be resolved (in this case because of an unresolved
neighbor), then mirror installation fails until the path is resolved.
This results in a race that causes the test to sometimes fail.
Fix this by setting the neighbor's state to permanent, so that it is
always valid.
Fixes: b5b029399fa6d ("selftests: forwarding: mirror_gre_bridge_1d_vlan: Add STP test")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 11df27f7fdf02cc2bb354358ad482e1fdd690589 ]
Specify the interface through which packets should be transmitted so
that the test will pass regardless of the libnet version against which
mausezahn is linked.
Fixes: cab14d1087d9 ("selftests: Add version of router_multipath.sh using nexthop objects")
Fixes: 3d578d879517 ("selftests: forwarding: Test IPv4 weighted nexthops")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 71a0e29e99405d89b695882d52eec60844173697 ]
When 'rp_filter' is configured in strict mode (1) the tests fail because
packets received from the macvlan netdevs would not be forwarded through
them on the reverse path.
Fix this by disabling the 'rp_filter', meaning no source validation is
performed.
Fixes: 1538812e0880 ("selftests: forwarding: Add a test for VXLAN asymmetric routing")
Fixes: 438a4f5665b2 ("selftests: forwarding: Add a test for VXLAN symmetric routing")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20201015084525.135121-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9b64208f74fbd0e920475ecfe9326f8443fdc3a5 ]
0x11 and 0x12 set the ECN bits based on RFC2474, it would be better to avoid
that. 0x14 and 0x18 would be better and works as well.
Reported-by: Petr Machata <petrm@mellanox.com>
Fixes: 4e867c9a50ff ("selftests: forwarding: vxlan_bridge_1d: fix tos value")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e867c9a50ff1a07ed0b86c3b1c8bc773933d728 ]
After commit 71130f29979c ("vxlan: fix tos value before xmit") we start
strict vxlan xmit tos value by RT_TOS(), which limits the tos value less
than 0x1E. With current value 0x40 the test will failed with "v1: Expected
to capture 10 packets, got 0". So let's choose a smaller tos value for
testing.
Fixes: d417ecf533fe ("selftests: forwarding: vxlan_bridge_1d: Add a TOS test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8023b030ce1748930e2dc76353a262fe47d4745 ]
For tc ip_proto filter, when we extract the flow via __skb_flow_dissect()
without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to
the inner proto.
So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP
proto.
For test mirror_gre.sh, it may make user confused if we capture ICMP
message on $h3(since the flow is GRE message). So I move the capture
dev to h3-gt{4,6}, and only capture ICMP message.
Before the fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
After fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
Fixes: ba8d39871a10 ("selftests: forwarding: Add test for mirror to gretap")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <pmachata@gmail.com>
Tested-by: Petr Machata <pmachata@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cc7e3f63d7299dd1119be39aa187b867d6f8aa17 upstream.
The loopback feature is only supported on a few drivers like broadcom,
mellanox, etc. The default veth driver has not supported it yet. To avoid
returning failed and making the runner feel confused, let's just skip
the test on drivers that not support loopback.
Fixes: ad11340994d5 ("selftests: Add loopback test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 65cb13986229cec02635a1ecbcd1e2dd18353201 ]
When creating the second host in h2_create(), two addresses are assigned
to the interface, but only one is deleted. When running the test twice
in a row the following error is observed:
$ ./router_bridge_vlan.sh
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: vlan [ OK ]
$ ./router_bridge_vlan.sh
RTNETLINK answers: File exists
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: vlan [ OK ]
Fix this by deleting the address during cleanup.
Fixes: 5b1e7f9ebd56 ("selftests: forwarding: Test routed bridge interface")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add helpers to interact with devlink-trap, such as setting the action of
a trap and retrieving statistics.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For tests that create their network interfaces dynamically or do not use
interfaces at all (as with netdevsim) it is useful to define their own
devlink device instead of deriving it from the first network interface.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Push the jq return value workaround code into a separate helper so it
could be used by the rest of the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TC filters used in the test do not work with veth devices because the
outer Ethertype is 802.1Q and not IPv4. The test passes with mlxsw
netdevs since the hardware always looks at "The first Ethertype that
does not point to either: VLAN, CNTAG or configurable Ethertype".
Fix this by matching on the VLAN ID instead, but on the ingress side.
The reason why this is not performed at egress is explained in the
commit cited below.
Fixes: 541ad323db3a ("selftests: forwarding: gre_multipath: Update next-hop statistics match criteria")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test did not enable IPv4 forwarding during its setup phase, which
causes the test to fail on machines where IPv4 forwarding is disabled.
Fixes: 54818c4c4b93 ("selftests: forwarding: Test multipath tunneling")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add selftest scripts for multipath hashing on inner IP pkts when there
is a single GRE tunnel but there are multiple underlay routes to reach
the other end of the tunnel.
Four cases are covered in these scripts:
- IPv4 inner, IPv4 outer
- IPv6 inner, IPv4 outer
- IPv4 inner, IPv6 outer
- IPv6 inner, IPv6 outer
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend tc_flower to test plain ingress device matching and also
tc_shblock to test ingress device matching on shared block.
Add new tc_flower_router.sh where ingress device matching on egress
(after routing) is done.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Honestly all the conflicts were simple overlapping changes,
nothing really interesting to report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a version of router_multipath.sh that uses nexthop objects for
routes.
Ido requested a version that does not cause regressions with mlxsw
testing since it does not support nexthop objects yet.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl setting bc_forwarding for $rp2 is needed when ping_test_from h2,
otherwise the bc packets from $rp2 won't be forwarded. This patch is to
add this setting for $rp2.
Also, as ping_test_from does grep "$from" only, which could match some
unexpected output, some test case doesn't really work, like:
# ping_test_from $h2 198.51.200.255 198.51.200.2
PING 198.51.200.255 from 198.51.100.2 veth3: 56(84) bytes of data.
64 bytes from 198.51.100.1: icmp_seq=1 ttl=64 time=0.336 ms
When doing grep $form (198.51.200.2), the output could still match.
So change to grep "bytes from $from" instead.
Fixes: 40f98b9af943 ("selftests: add a selftest for directed broadcast forwarding")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add selftest for loopback feature
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This test is split in two, the first part checks if a report creates a
corresponding mdb entry and if traffic is properly forwarded to it, and
the second part checks if the mdb entry is deleted after a leave and
if traffic is *not* forwarded to it. Since the mcast querier is enabled
we should see standard mcast snooping bridge behaviour.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers to obtain, set, and restore a pool size, and a port-pool and
tc-pool threshold.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devlink -j and jq for more accurate querying. Use cut -f-2 instead
of rev-cut-rev combo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Construct a basic topology consisting of two hosts connected using a
VLAN-aware bridge. Put each port in a different VLAN and test that ping
fails.
Add ingress and egress filters with a VLAN modify action and test that
ping passes.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Send packets with VLAN and PCP set and check that TC flower filters can
match on these keys.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a packet is routed using a multicast route whose specified
ingress interface does not match the interface from which the packet was
received, the packet is dropped.
Add IPv4 and IPv6 test cases for above mentioned scenario.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the forwarding selftests to work, we need network namespaces when
using veth/vrf otherwise ping/ping6 commands like these:
ip vrf exec vveth0 /bin/ping 192.0.2.2 -c 10 -i 0.1 -w 5
will fail because network namespaces may not be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The global variable RET needs to be initialized before each call to
log_test. This test case sets it once before running the tests, but then
calls log_tests for every individual test. Thus a failure in one of the
tests causes spurious failures in follow-up tests as well.
Fix by moving the initialization of RET from test_all() to
full_test_span_gre_dir_acl(), a function that implements the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This test sets up mirroring such that it mirrors all overlay traffic.
That includes ARP, which causes occasional miscounts and spurious
failures. Ignore ARP explicitly to avoid these problems.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This test relies on routing in the primary traffic path, but neglects to
enable forwarding. Do so.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After one LAG slave is downed and another upped, it takes a while for
the neighbor on a bridge to time out and get renegotiated. The test does
prompt update of FDB entries by arpinging. But because the neighbor
still references another address, offloading is not possible, and some
packets may end up not being mirrored.
To force the neighbor renegotiation, simply flush the neighbor table at
the bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARP or ND traffic can cause spurious migration of FDB back to $swp3.
Mirroring is then updated in accordance with the change, and mirrored
packets are seen at h3, causing a failure.
Detect the case of this spurious roaming, and retry the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The untagged egress test sets up mirroring to {,ip6}gretap such that the
underlay goes through a bridge. Then VLAN flags are manipulated to test
that the traffic leaves the bridge 802.1q-tagged or not, as appropriate.
However, when a neighbor expires at the time that the bridge VLAN is
configured as PVID and egress untagged, the following discovery process
can't finish, because the IP address on H3 is still at the VLAN-tagged
netdevice. This manifests by occasional failures where only several of
the 10 required packets get through.
Therefore, when reconfiguring the VLAN flags, move the IP address to the
appropriate device in the H3 VRF.
In addition to that, take this opportunity to embed an ASCII art diagram
to make the topology move obvious.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in an environment with poor performance (such as a
simulator), processing mirrored packets can take a while. Evaluating the
condition too soon leads to spurious "seen 9, expected 10" failures as
the last packet doesn't have enough time to get mirrored and the mirror
to arrive and bump the observed counters.
Wait for one ping interval before evaluating the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in a simulator, the TTL change takes a while to settle and
during this time the performance of the packet processing is lowered.
The resulting instability leads to ping sending more packets as it
assumes some have been dropped. This then leads to regular spurious
failures as more packets than expected are observed.
Sleep a bit to give the system time to stabilize.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. Those
are mirrored, and over a certain threshold the test case run is
considered a failure, because too much traffic is observed.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is easier to distinguish "[ OK ]" from "[FAIL]" than "[PASS]".
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARP suppression allows the Linux bridge to answer ARP requests on behalf
of remote hosts. It reduces the amount of packets a VTEP needs to flood.
This test verifies that ARP suppression on / off works when a neighbour
exists and when it does not exist. It does so by sending an ARP request
from a host connected to one VTEP and checking whether it was received
by a second VTEP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VXLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI. Different tenants
(VRFs) use different L3 VNIs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify that ARP packets are correctly decapsulated by the ingress VTEP
by removing the neighbours configured on both VLAN interfaces and
running a ping test.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In asymmetric routing the ingress VTEP routes the packet into the
correct VXLAN tunnel, whereas the egress VTEP only bridges the packet to
the correct host. Therefore, packets in different directions use
different VNIs - the target VNI.
The test uses a simple topology with two VTEPs and two VNIs and verifies
that ping passes between hosts (local / remote) in the same VLAN (VNI)
and in different VLANs belonging to the same tenant (VRF).
While the test does not check VM mobility, it does configure an anycast
gateway using a macvlan device on both VTEPs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Ido Schimmel
Hangbin Liu
Petr Machata
Davide Caratti
Danielle Ratson
Ido Schimmel
Jiri Pirko
Stephen Suryaputra
David S. Miller
David Ahern
Xin Long
Nikolay Aleksandrov
Petr Machata
Danielle Ratson
Amit Cohen
Florian Fainelli