| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 0306988789d9d91a18ff70bd2bf165d3ae0ef1dd ]
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d591d4b32aa9552af14a0c7c586a2d3fe9ecc6e0 ]
Some registers had wrong default values in cs42l42_reg_defaults[].
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211015133619.4698-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b353bbeae20e2214c9d9d88bcb2fda4ba145d83 ]
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30615bd21b4cc3c3bb5ae8bd70e2a915cc5f75c7 ]
The underlying register field has inverted sense (0 = enabled) so
the control definition must be marked as inverted.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64324bac750b84ca54711fb7d332132fcdb87293 ]
The driver has no support for left-justified protocol so it should
not have been allowing this to be passed to cs42l42_set_dai_fmt().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210729170929.6589-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee86f680ff4c9b406d49d4e22ddf10805b8a2137 ]
The ADC volume is a signed 8-bit number with range -97 to +12,
with -97 being mute. Use a SOC_SINGLE_S8_TLV() to define this
and fix the DECLARE_TLV_DB_SCALE() to have the correct start and
mute flag.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210729170929.6589-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fac165f22ac947b55407cd3a60a2a9824f905235 ]
The definition of CS42L42_ADC_PDN_MASK was incorrectly defined
as the HP_PDN bit.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210616135604.19363-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e072b2671606c77538d6a4dd5dda80b508cb4816 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620789145-14936-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 833bc4cf9754643acc69b3c6b65988ca78df4460 ]
This error path returns zero (success) but it should return -EINVAL.
Fixes: 3333cb7187b9 ("ASoC: cs35l33: Initial commit of the cs35l33 CODEC driver.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/YKXuyGEzhPT35R3G@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd8499d5c03ba260e3191e90236d0e5f6b147563 ]
The GPIO configuration cannot be applied if the registers are inaccessible.
This prevented the headset mic from working on the Dell XPS 13 9343.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=114171
Signed-off-by: David Ward <david.ward@gatech.edu>
Link: https://lore.kernel.org/r/20210418134658.4333-5-david.ward@gatech.edu
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa2f9c12821e6a4ba1df4fb34a3dbc6a2a1ee7fe ]
The ALC3263 codec on the XPS 13 9343 is also found on the Latitude 13 7350
and Venue 11 Pro 7140. They require the same handling for the combo jack to
work with a headset: GPIO pin 6 must be set.
The HDA driver always sets this pin on the ALC3263, which it distinguishes
by the codec vendor/device ID 0x10ec0288 and PCI subsystem vendor ID 0x1028
(Dell). The ASoC driver does not use PCI, so adapt this check to use DMI to
determine if Dell is the system vendor.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=150601
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205961
Signed-off-by: David Ward <david.ward@gatech.edu>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210418134658.4333-6-david.ward@gatech.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 16b82e75c15a7dbd564ea3654f3feb61df9e1e6f ]
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d519f ("ASoC: codec: wm9860: Refactor PLL out freq search")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dbf54a9534350d6aebbb34f5c1c606b81a4f35dd ]
Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1615829492-8972-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 19325cfea04446bc79b36bffd4978af15f46a00e ]
This delay is part of the power-up sequence defined in the datasheet.
A runtime_resume is a power-up so must also include the delay.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72d904763ae6a8576e7ad034f9da4f0e3c44bf24 ]
The minimum value is 0x3f (-63dB), which also is mute
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-4-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb18c678754ce1514100fb4c0bf6113b5af36c48 ]
Most steps in this table are steps of 3dB (300 centi-dB), so we can
simplify the table.
This not only reduces the amount of space it takes inside the kernel,
this also makes alsa-lib's mixer code actually accept the table, where
as before this change alsa-lib saw the "ADC PGA Gain" control as a
control without a dB scale.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210228160441.241110-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f86f58e3594fb0ab1993d833d3b9a2496f3c928c ]
According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has
the following bit field definitions:
| BITS | FIELD | RW | RESET | DEFINITION |
| 15 | RSVD | RO | 0x0 | Reserved |
| 14 | RSVD | RW | 0x1 | Reserved |
| 13:12 | MAX_GAIN | RW | 0x1 | Max Gain of AVC in expander mode |
| 11:10 | RSVD | RO | 0x0 | Reserved |
| 9:8 | LBI_RESP | RW | 0x1 | Integrator Response |
| 7:6 | RSVD | RO | 0x0 | Reserved |
| 5 | HARD_LMT_EN | RW | 0x0 | Enable hard limiter mode |
| 4:1 | RSVD | RO | 0x0 | Reserved |
| 0 | EN | RW | 0x0 | Enable/Disable AVC |
The original default value written to the DAP_AVC_CTRL register during
sgtl5000_i2c_probe() was 0x0510. This would incorrectly write values to
bits 4 and 10, which are defined as RESERVED. It would also not set
bits 12 and 14 to their correct RESET values of 0x1, and instead set
them to 0x0. While the DAP_AVC module is effectively disabled because
the EN bit is 0, this default value is still writing invalid values to
registers that are marked as read-only and RESERVED as well as not
setting bits 12 and 14 to their correct default values as defined by the
datasheet.
The correct value that should be written to the DAP_AVC_CTRL register is
0x5100, which configures the register bits to the default values defined
by the datasheet, and prevents any writes to bits defined as
'read-only'. Generally speaking, it is best practice to NOT attempt to
write values to registers/bits defined as RESERVED, as it generally
produces unwanted/undefined behavior, or errors.
Also, all credit for this patch should go to my colleague Dan MacDonald
<dmacdonald@curbellmedical.com> for finding this error in the first
place.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Benjamin Rood <benjaminjrood@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-dev
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eee51df776bd6cac10a76b2779a9fdee3f622b2b ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b540 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cfa26ed1f9f885c2fd8f53ca492989d1e16d0199 ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b540 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 856fe64da84c95a1d415564b981ae3908eea2a76 ]
There are two issues with this code. The first error path forgot to set
the error code and instead returns success. The second error path
doesn't clean up.
Fixes: 272b5edd3b8f ("ASoC: Add support for CS42L56 CODEC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X9NE/9nK9/TuxuL+@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85a7555575a0e48f9b73db310d0d762a08a46d63 ]
The error handling frees "ctl" but it's still on the "dsp->ctl_list"
list so that could result in a use after free. Remove it from the list
before returning.
Fixes: 2323736dca72 ("ASoC: wm_adsp: Add basic support for rev 1 firmware file format")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/X9B0keV/02wrx9Xs@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5e7aace13df24ff72511f29c14ebbfe638ef733c ]
In the normal path, we should not free the arizona,
we should return immediately. It will be free when
call remove operation.
Fixes: 31833ead95c2c ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201111130923.220186-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 193aa0a043645220d2a2f783ba06ae13d4601078 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes: 31833ead95c2c ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201111041326.1257558-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff69c97ef84c9f7795adb49e9f07c9adcdd0c288 ]
For some reason interrupt set and clear register offsets are
not set correctly.
This patch corrects them!
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200811103452.20448-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5cacc6f5764e94fa753b2c1f5f7f1f3f74286e82 upstream.
The RT5670_PWR_ANLG1 register has 3 bits to select the LDO voltage,
so the correct mask is 0x7 not 0x3.
Because of this wrong mask we were programming the ldo bits
to a setting of binary 001 (0x05 & 0x03) instead of binary 101
when moving to SND_SOC_BIAS_PREPARE.
According to the datasheet 001 is a reserved value, so no idea
what it did, since the driver was working fine before I guess we
got lucky and it does something which is ok.
Fixes: 5e8351de740d ("ASoC: add RT5670 CODEC driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200628155231.71089-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 326b509238171d37402dbe308e154cc234ed1960 ]
If we don't find any pcm, pcm will point at address at an offset from
the the list head and not a meaningful structure. Fix this by returning
correct pcm if found and NULL if not. Found with coccinelle.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20200415162849.308-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa7812737f2877e192d57626cbe8825cc7cf6de9 ]
As mentioned slightly out of patch context in the code, there
is no reset routine for the chip. On boards where the chip is
supplied by a fixed regulator, it might not even be resetted
during (e.g. watchdog) reboot and can be in any state.
If the device is probed with VAG enabled, the driver's probe
routine will generate a loud pop sound when ANA_POWER is
being programmed. Avoid this by properly disabling just the
VAG bit and waiting the required power down time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Fabio Estevam <festivem@gmail.com>
Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ac0a68997935c4acb92eaae5ad8982e0bb432d56 upstream.
When we get a clock error during probe we have to call
regulator_bulk_disable before bailing out, otherwise we trigger
a warning in regulator_put.
Fix this by using "goto err" like in the error cases above.
Fixes: 5a3af1293194d ("ASoC: pcm512x: Add PCM512x driver")
Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200220202956.29233-1-hias@horus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 554b75bde64bcad9662530726d1483f7ef012069 ]
sound/soc/codecs/wm8737.c:112:29: warning:
high_3d defined but not used [-Wunused-const-variable=]
'high_3d' should be used for 3D High Cut-off.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2a9ae13a2641 ("ASoC: Add initial WM8737 driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190815091920.64480-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9b4275c415acca6264a3d7f1182589959c93d530 ]
sound/soc/codecs/cs4349.c:358:32: warning:
cs4349_runtime_pm defined but not used [-Wunused-const-variable=]
cs4349_runtime_pm ops already defined, it seems
we should enable it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e40da86 ("ASoC: cs4349: Add support for Cirrus Logic CS4349")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190815090157.70036-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 630742c296341a8cfe00dfd941392025ba8dd4e8 ]
It seems 'es8328_rline_enum' should be used
in es8328_right_line_controls
Fixes: 567e4f98922c ("ASoC: add es8328 codec driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190815092300.68712-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e0beec88397b163c7c4ea6fcfb67e8e07a2671dc upstream.
MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().
But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.
Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 556672d75ff486e0b6786056da624131679e0576 ]
According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).
Fixes: 9a76f1ff6e29 ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eabf424f7b60246c76dcb0ea6f1e83ef9abbeaa6 ]
The codec dies when RT5677_PWR_ANLG2(MX-64h) is set to 0xACE1
while it's streaming audio over SPI. The DSP firmware turns
on PLL2 (MX-64 bit 8) when SPI streaming starts. However regmap
does not believe that register can change by itself. When
BST1 (bit 15) is turned on with regmap_update_bits(), it doesn't
read the register first before write, so PLL2 power bit is
cleared by accident.
Marking MX-64h as volatile in regmap solved the issue.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-6-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd7fdc45bc69a62b4e22c6e875f1f1aea566256d ]
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Signed-off-by: Young_X <YangX92@hotmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9110d1b0e229cebb1ffce0c04db2b22beffd513d ]
According to the PM8916 Hardware Register Description,
CDC_D_CDC_CONN_HPHR_DAC_CTL has only a single bit (RX_SEL)
to switch between RX1 (0) and RX2 (1). It is not possible to
disable it entirely to achieve the "ZERO" state.
However, at the moment the "RDAC2 MUX" mixer defines three possible
values ("ZERO", "RX2" and "RX1"). Setting the mixer to "ZERO"
actually configures it to RX1. Setting the mixer to "RX1" has
(seemingly) no effect.
Remove "ZERO" and replace it with "RX1" to fix this.
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191020153007.206070-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b857472f34faa7d11001afa5e158833812c98d7 ]
Playback of 44.1Khz contents with HDMI plugged returns
"Invalid pipe config" because HDMI paths in the FW
topology are configured to operate at 48Khz.
This patch filters out sampling rates not supported
at hdac_hdmi_create_dais() to let user space SRC
to do the converting.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9ab708aef61f5620113269a9d1bdb1543d1207d0 ]
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 09fc38c1af4cb888255e9ecf267bf9757c12885d upstream
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1195220
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcb407b257af06fa58b0544ec01ec9e0d3927e02 upstream
Currently BCLK inverting is only handled when the DAI format is
DSP, but the BCLK may be inverted in any supported mode. Without
this using this CODEC in any other mode than DSP with the BCLK
inverted leads to bad sampling timing and very poor audio quality.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3ae7359c0e39f42a96284d6798fc669acff38140 ]
User space always expects to be able to read ALSA controls, so ensure
no kcontrols are generated without an appropriate READ flag. In the case
of a read of such a control zeros will be returned.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191002084240.21589-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1f373a11d25fc9a5f7679c9b85799fe09b0dc4a ]
VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.
I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN
Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
prevents pop during line-in muxing.
According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Cc: stable@vger.kernel.org
Fixes: 9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190719100524.23300-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f972d02fee2496024cfd6f59021c9d89d54922a6 ]
This patch fix setting table of Headphone mixer volume.
Current code uses 4 ... 7 values but these values are prohibited.
Correct settings are the following:
0000 -12dB
0001 -10.5dB
0010 -9dB
0011 -7.5dB
0100 -6dB
1000 -4.5dB
1001 -3dB
1010 -1.5dB
1011 0dB
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/r/20190826153900.25969-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6319b061ba279577fd7030a9848fbd6a17151e3 ]
If VDDA != VDDIO and any of them is greater than 3.1V, charge pump
source can be assigned automatically [1].
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-7-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 04268bf2757a125616b6c2140e6250f43b7b737a ]
When we call snd_soc_component_set_jack(component, NULL, NULL) we should
set rt274->jack to passed jack, so when interrupt is triggered it calls
snd_soc_jack_report(rt274->jack, ...) with proper value.
This fixes problem in machine where in register, we call
snd_soc_register(component, &headset, NULL), which just calls
rt274_mic_detect via callback.
Now when machine driver is removed "headset" will be gone, so we
need to tell codec driver that it's gone with:
snd_soc_register(component, NULL, NULL), but we also need to be able
to handle NULL jack argument here gracefully.
If we don't set it to NULL, next time the rt274_irq runs it will call
snd_soc_jack_report with first argument being invalid pointer and there
will be Oops.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5628c8979642a076f91ee86c3bae5ad251639af0 ]
The supported formats are S16_LE and S24_LE now. However, by datasheet
of max98090, S24_LE is only supported when it is in the right justified
mode. We should remove 24-bit format if it is not in that mode to avoid
triggering error.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3df05c805983427319eddc2411a2105ee1757cf ]
The cs4265_readable_register function stopped short of the maximum
register.
An example bug is taken from :
https://github.com/Audio-Injector/Ultra/issues/25
Where alsactl store fails with :
Cannot read control '2,0,0,C Data Buffer,0': Input/output error
This patch fixes the bug by setting the cs4265 to have readable
registers up to the maximum hardware register CS4265_MAX_REGISTER.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ad6eecbfc01c987e0253371f274c3872042e4350 upstream.
Add regcache_mark_dirty before regcache_sync for power
of codec may be lost at suspend, then all the register
need to be reconfigured.
Fixes: 0c516b4ff85c ("ASoC: cs42xx8: Add codec driver
support for CS42448/CS42888")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 30180e8436046344b12813dc954b2e01dfdcd22d ]
If the hdmi codec startup fails, it should clear the current_substream
pointer to free the device. This is properly done for the audio_startup()
callback but for snd_pcm_hw_constraint_eld().
Make sure the pointer cleared if an error is reported.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a46eb523220e242affb9a6bc9bb8efc05f4f7459 upstream.
The current algorithm allows 3 types of transfers, 16bit, 32bit and
burst. According to Realtek, 16bit transfers have a special restriction
in that it is restricted to the memory region of
0x18020000 ~ 0x18021000. This region is the memory location of the I2C
registers. The current algorithm does not uphold this restriction and
therefore fails to complete writes.
Since this has been broken for some time it likely no one is using it.
Better to simply disable the 16 bit writes. This will allow users to
properly load firmware over SPI without data corruption.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Richard Fitzgerald
Zou Wei
Dan Carpenter
David Ward
Shengjiu Wang
Sameer Pujar
Lucas Tanure
Hans de Goede
Benjamin Rood
Zhang Qilong
Srinivas Kandagatla
Amadeusz Sławiński
Sebastian Reichel
Matthias Reichl
YueHaibing
Stephan Gerhold
Ben Zhang
Young_X
Yong Zhi
Colin Ian King
Gustavo A. R. Silva
Andrew F. Davis
Stuart Henderson
Oleksandr Suvorov
Katsuhiro Suzuki
Yu-Hsuan Hsu
Matt Flax
Jerome Brunet
Curtis Malainey