| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The function batadv_gw_deselect() is actually not deselecting
anything. It is just informing the GW code to perform a
re-election procedure when possible.
The current gateway is not being touched at all and therefore
the name of this function is rather misleading.
Rename it to batadv_gw_reselect() to batadv_gw_reselect()
to make its behaviour easier to grasp.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
When switching from gw_mode client to either off or server
the current selected gateway has to be deselected.
In this way when client mode is enabled again a gateway
re-election is forced and a GW_ADD event is consequently
sent.
The current behaviour instead is to keep the current gateway
leading to no GW_ADD event when gw_mode client is selected
for a second time
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
AP isolation has to be enabled on one VLAN interface only.
This patch moves the AP isolation attribute to the per-vlan
interface attribute set, enabling it to have a different
value depending on the selected vlan.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Each VLAN can now have its own set of attributes which are
exported through a new subfolder in the sysfs tree.
Each VLAN created on top of a soft_iface will have its own
subfolder.
The subfolder is named "vlan%VID" and it is created inside
the "mesh" sysfs folder belonging to batman-adv.
Attributes corresponding to the untagged LAN are stored in
the root sysfs folder as before.
This patch also creates all the needed macros and data
structures to easily handle new VLAN spacific attributes.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Create network coding container to announce network coding
capabilities (if enabled).
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Create DAT container to announce DAT capabilities (if enabled).
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Whenever the GW client mode is deselected, a DEL event has
to be sent in order to tell userspace that the current
gateway has been lost. Send the uevent on state change only
if a gateway was currently selected.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
it is taken
The rtnl_lock in batadv_store_mesh_iface has been converted to a rtnl_trylock
some time ago to avoid a possible deadlock between rtnl and s_active on removal
of the sysfs nodes.
The behaviour introduced by that was quite confusing as it could lead to the
sysfs store to fail, making batman-adv setup scripts unreliable. As recently the
sysfs removal was postponed to a worker not running with the rtnl taken, the
deadlock can't occur any more and it is safe to change the trylock back to a
lock to make the sysfs store reliable again.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
batman-adv has an unusual way to manage softinterfaces. These will be created
automatically when a user writes to the batman-adv/mesh_iface file in sysfs and
removed when no slave device exists anymore.
This behaviour cannot be changed without breaking compatibility with existing
code. Instead other interfaces should be able to slightly reduce this behaviour
and provide a more common reaction to a removal of a slave interface.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
The batadv_priv struct carries a pointer to its own interface
struct. Therefore, it is not necessary to retrieve the soft_iface
via the primary interface.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
This patch adds a runtime switch that enables the user to turn the DAT feature
on or off at runtime
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
The "bat_" prefix in the source files implementing the batman-adv sysfs and
debugfs interface doesn't have a special meaning and are only used by these
files and files that implement the actual B.A.T.M.A.N. path finding algorithm.
The prefix is better suited to mark files that are used to implement the main
part of the path finding. All other files should not use it and therefore gets
renamed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
Simon Wunderlich
Antonio Quartulli
Antonio Quartulli
Simon Wunderlich
Marek Lindner
Matthias Schiffer
Sven Eckelmann
Martin Hundebøll
Antonio Quartulli