| Age | Commit message (Collapse) | Author |
|---|
|
commit b431ef837e3374da0db8ff6683170359aaa0859c upstream.
We make an assumption that a debugfs directory exists, but since
this can fail ensure it exists before allowing blktrace setup to
complete. Otherwise we end up stuffing blktrace files on the debugfs
root directory. In the worst case scenario this *in theory* can create
an eventual panic *iff* in the future a similarly named file is created
prior on the debugfs root directory. This theoretical crash can happen
due to a recursive removal followed by a specific dentry removal.
This doesn't fix any known crash, however I have seen the files
go into the main debugfs root directory in cases where the debugfs
directory was not created due to other internal bugs with blktrace
now fixed.
blktrace is also completely useless without this directory, so
this ensures to userspace we only setup blktrace if the kernel
can stuff files where they are supposed to go into.
debugfs directory creations typically aren't checked for, and we have
maintainers doing sweep removals of these checks, but since we need this
check to ensure proper userspace blktrace functionality we make sure
to annotate the justification for the check.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bad8e64fb19d3a0de5e564d9a7271c31bd684369 upstream.
On commit 6ac93117ab00 ("blktrace: use existing disk debugfs directory")
merged on v4.12 Omar fixed the original blktrace code for request-based
drivers (multiqueue). This however left in place a possible crash, if you
happen to abuse blktrace while racing to remove / add a device.
We used to use asynchronous removal of the request_queue, and with that
the issue was easier to reproduce. Now that we have reverted to
synchronous removal of the request_queue, the issue is still possible to
reproduce, its however just a bit more difficult.
We essentially run two instances of break-blktrace which add/remove
a loop device, and setup a blktrace and just never tear the blktrace
down. We do this twice in parallel. This is easily reproduced with the
script run_0004.sh from break-blktrace [0].
We can end up with two types of panics each reflecting where we
race, one a failed blktrace setup:
[ 252.426751] debugfs: Directory 'loop0' with parent 'block' already present!
[ 252.432265] BUG: kernel NULL pointer dereference, address: 00000000000000a0
[ 252.436592] #PF: supervisor write access in kernel mode
[ 252.439822] #PF: error_code(0x0002) - not-present page
[ 252.442967] PGD 0 P4D 0
[ 252.444656] Oops: 0002 [#1] SMP NOPTI
[ 252.446972] CPU: 10 PID: 1153 Comm: break-blktrace Tainted: G E 5.7.0-rc2-next-20200420+ #164
[ 252.452673] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
[ 252.456343] RIP: 0010:down_write+0x15/0x40
[ 252.458146] Code: eb ca e8 ae 22 8d ff cc cc cc cc cc cc cc cc cc cc cc cc
cc cc 0f 1f 44 00 00 55 48 89 fd e8 52 db ff ff 31 c0 ba 01 00
00 00 <f0> 48 0f b1 55 00 75 0f 48 8b 04 25 c0 8b 01 00 48 89
45 08 5d
[ 252.463638] RSP: 0018:ffffa626415abcc8 EFLAGS: 00010246
[ 252.464950] RAX: 0000000000000000 RBX: ffff958c25f0f5c0 RCX: ffffff8100000000
[ 252.466727] RDX: 0000000000000001 RSI: ffffff8100000000 RDI: 00000000000000a0
[ 252.468482] RBP: 00000000000000a0 R08: 0000000000000000 R09: 0000000000000001
[ 252.470014] R10: 0000000000000000 R11: ffff958d1f9227ff R12: 0000000000000000
[ 252.471473] R13: ffff958c25ea5380 R14: ffffffff8cce15f1 R15: 00000000000000a0
[ 252.473346] FS: 00007f2e69dee540(0000) GS:ffff958c2fc80000(0000) knlGS:0000000000000000
[ 252.475225] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 252.476267] CR2: 00000000000000a0 CR3: 0000000427d10004 CR4: 0000000000360ee0
[ 252.477526] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 252.478776] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 252.479866] Call Trace:
[ 252.480322] simple_recursive_removal+0x4e/0x2e0
[ 252.481078] ? debugfs_remove+0x60/0x60
[ 252.481725] ? relay_destroy_buf+0x77/0xb0
[ 252.482662] debugfs_remove+0x40/0x60
[ 252.483518] blk_remove_buf_file_callback+0x5/0x10
[ 252.484328] relay_close_buf+0x2e/0x60
[ 252.484930] relay_open+0x1ce/0x2c0
[ 252.485520] do_blk_trace_setup+0x14f/0x2b0
[ 252.486187] __blk_trace_setup+0x54/0xb0
[ 252.486803] blk_trace_ioctl+0x90/0x140
[ 252.487423] ? do_sys_openat2+0x1ab/0x2d0
[ 252.488053] blkdev_ioctl+0x4d/0x260
[ 252.488636] block_ioctl+0x39/0x40
[ 252.489139] ksys_ioctl+0x87/0xc0
[ 252.489675] __x64_sys_ioctl+0x16/0x20
[ 252.490380] do_syscall_64+0x52/0x180
[ 252.491032] entry_SYSCALL_64_after_hwframe+0x44/0xa9
And the other on the device removal:
[ 128.528940] debugfs: Directory 'loop0' with parent 'block' already present!
[ 128.615325] BUG: kernel NULL pointer dereference, address: 00000000000000a0
[ 128.619537] #PF: supervisor write access in kernel mode
[ 128.622700] #PF: error_code(0x0002) - not-present page
[ 128.625842] PGD 0 P4D 0
[ 128.627585] Oops: 0002 [#1] SMP NOPTI
[ 128.629871] CPU: 12 PID: 544 Comm: break-blktrace Tainted: G E 5.7.0-rc2-next-20200420+ #164
[ 128.635595] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
[ 128.640471] RIP: 0010:down_write+0x15/0x40
[ 128.643041] Code: eb ca e8 ae 22 8d ff cc cc cc cc cc cc cc cc cc cc cc cc
cc cc 0f 1f 44 00 00 55 48 89 fd e8 52 db ff ff 31 c0 ba 01 00
00 00 <f0> 48 0f b1 55 00 75 0f 65 48 8b 04 25 c0 8b 01 00 48 89
45 08 5d
[ 128.650180] RSP: 0018:ffffa9c3c05ebd78 EFLAGS: 00010246
[ 128.651820] RAX: 0000000000000000 RBX: ffff8ae9a6370240 RCX: ffffff8100000000
[ 128.653942] RDX: 0000000000000001 RSI: ffffff8100000000 RDI: 00000000000000a0
[ 128.655720] RBP: 00000000000000a0 R08: 0000000000000002 R09: ffff8ae9afd2d3d0
[ 128.657400] R10: 0000000000000056 R11: 0000000000000000 R12: 0000000000000000
[ 128.659099] R13: 0000000000000000 R14: 0000000000000003 R15: 00000000000000a0
[ 128.660500] FS: 00007febfd995540(0000) GS:ffff8ae9afd00000(0000) knlGS:0000000000000000
[ 128.662204] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 128.663426] CR2: 00000000000000a0 CR3: 0000000420042003 CR4: 0000000000360ee0
[ 128.664776] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 128.666022] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 128.667282] Call Trace:
[ 128.667801] simple_recursive_removal+0x4e/0x2e0
[ 128.668663] ? debugfs_remove+0x60/0x60
[ 128.669368] debugfs_remove+0x40/0x60
[ 128.669985] blk_trace_free+0xd/0x50
[ 128.670593] __blk_trace_remove+0x27/0x40
[ 128.671274] blk_trace_shutdown+0x30/0x40
[ 128.671935] blk_release_queue+0x95/0xf0
[ 128.672589] kobject_put+0xa5/0x1b0
[ 128.673188] disk_release+0xa2/0xc0
[ 128.673786] device_release+0x28/0x80
[ 128.674376] kobject_put+0xa5/0x1b0
[ 128.674915] loop_remove+0x39/0x50 [loop]
[ 128.675511] loop_control_ioctl+0x113/0x130 [loop]
[ 128.676199] ksys_ioctl+0x87/0xc0
[ 128.676708] __x64_sys_ioctl+0x16/0x20
[ 128.677274] do_syscall_64+0x52/0x180
[ 128.677823] entry_SYSCALL_64_after_hwframe+0x44/0xa9
The common theme here is:
debugfs: Directory 'loop0' with parent 'block' already present
This crash happens because of how blktrace uses the debugfs directory
where it places its files. Upon init we always create the same directory
which would be needed by blktrace but we only do this for make_request
drivers (multiqueue) block drivers. When you race a removal of these
devices with a blktrace setup you end up in a situation where the
make_request recursive debugfs removal will sweep away the blktrace
files and then later blktrace will also try to remove individual
dentries which are already NULL. The inverse is also possible and hence
the two types of use after frees.
We don't create the block debugfs directory on init for these types of
block devices:
* request-based block driver block devices
* every possible partition
* scsi-generic
And so, this race should in theory only be possible with make_request
drivers.
We can fix the UAF by simply re-using the debugfs directory for
make_request drivers (multiqueue) and only creating the ephemeral
directory for the other type of block devices. The new clarifications
on relying on the q->blk_trace_mutex *and* also checking for q->blk_trace
*prior* to processing a blktrace ensures the debugfs directories are
only created if no possible directory name clashes are possible.
This goes tested with:
o nvme partitions
o ISCSI with tgt, and blktracing against scsi-generic with:
o block
o tape
o cdrom
o media changer
o blktests
This patch is part of the work which disputes the severity of
CVE-2019-19770 which shows this issue is not a core debugfs issue, but
a misuse of debugfs within blktace.
Fixes: 6ac93117ab00 ("blktrace: use existing disk debugfs directory")
Reported-by: syzbot+603294af2d01acfdd6da@syzkaller.appspotmail.com
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: yu kuai <yukuai3@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a67549c8e568627290234e9fbe833cb9dfd36b55 upstream.
Ensure it is clear which lock is required on do_blk_trace_setup().
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c3dbe541ef77754729de5e82be2d6e5d267c6c8c upstream.
Mostly for historical reasons, q->blk_trace is assigned through xchg()
and cmpxchg() atomic operations. Although this is correct, sparse
complains about this because it violates rcu annotations since commit
c780e86dd48e ("blktrace: Protect q->blk_trace with RCU") which started
to use rcu for accessing q->blk_trace. Furthermore there's no real need
for atomic operations anymore since all changes to q->blk_trace happen
under q->blk_trace_mutex and since it also makes more sense to check if
q->blk_trace is set with the mutex held earlier.
So let's just replace xchg() with rcu_replace_pointer() and cmpxchg()
with explicit check and rcu_assign_pointer(). This makes the code more
efficient and sparse happy.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3e6f176f304ee8effec698ebaff6b7baecb5e1e6 upstream.
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 11990a5bd7e558e9203c1070fc52fb6f0488e75b upstream.
The only-root-readable /sys/module/$module/sections/$section files
did not truncate their output to the available buffer size. While most
paths into the kernfs read handlers end up using PAGE_SIZE buffers,
it's possible to get there through other paths (e.g. splice, sendfile).
Actually limit the output to the "count" passed into the read function,
and report it back correctly. *sigh*
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/20200805002015.GE23458@shao2-debian
Fixes: ed66f991bb19 ("module: Refactor section attr into bin attribute")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f0c7baca180046824e07fc5f1326e83a8fd150c7 upstream.
John reported that on a RK3288 system the perf per CPU interrupts are all
affine to CPU0 and provided the analysis:
"It looks like what happens is that because the interrupts are not per-CPU
in the hardware, armpmu_request_irq() calls irq_force_affinity() while
the interrupt is deactivated and then request_irq() with IRQF_PERCPU |
IRQF_NOBALANCING.
Now when irq_startup() runs with IRQ_STARTUP_NORMAL, it calls
irq_setup_affinity() which returns early because IRQF_PERCPU and
IRQF_NOBALANCING are set, leaving the interrupt on its original CPU."
This was broken by the recent commit which blocked interrupt affinity
setting in hardware before activation of the interrupt. While this works in
general, it does not work for this particular case. As contrary to the
initial analysis not all interrupt chip drivers implement an activate
callback, the safe cure is to make the deferred interrupt affinity setting
at activation time opt-in.
Implement the necessary core logic and make the two irqchip implementations
for which this is required opt-in. In hindsight this would have been the
right thing to do, but ...
Fixes: baedb87d1b53 ("genirq/affinity: Handle affinity setting on inactive interrupts correctly")
Reported-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/87blk4tzgm.fsf@nanos.tec.linutronix.de
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c16816acd08697b02a53f56f8936497a9f6f6e7a upstream.
In general calling generic_handle_irq() with interrupts disabled from non
interrupt context is harmless. For some interrupt controllers like the x86
trainwrecks this is outright dangerous as it might corrupt state if an
interrupt affinity change is pending.
Add infrastructure which allows to mark interrupts as unsafe and catch such
usage in generic_handle_irq().
Reported-by: sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.590923677@linutronix.de
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit baedb87d1b53532f81b4bd0387f83b05d4f7eb9a upstream.
Setting interrupt affinity on inactive interrupts is inconsistent when
hierarchical irq domains are enabled. The core code should just store the
affinity and not call into the irq chip driver for inactive interrupts
because the chip drivers may not be in a state to handle such requests.
X86 has a hacky workaround for that but all other irq chips have not which
causes problems e.g. on GIC V3 ITS.
Instead of adding more ugly hacks all over the place, solve the problem in
the core code. If the affinity is set on an inactive interrupt then:
- Store it in the irq descriptors affinity mask
- Update the effective affinity to reflect that so user space has
a consistent view
- Don't call into the irq chip driver
This is the core equivalent of the X86 workaround and works correctly
because the affinity setting is established in the irq chip when the
interrupt is activated later on.
Note, that this is only effective when hierarchical irq domains are enabled
by the architecture. Doing it unconditionally would break legacy irq chip
implementations.
For hierarchial irq domains this works correctly as none of the drivers can
have a dependency on affinity setting in inactive state by design.
Remove the X86 workaround as it is not longer required.
Fixes: 02edee152d6e ("x86/apic/vector: Ignore set_affinity call for inactive interrupts")
Reported-by: Ali Saidi <alisaidi@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ali Saidi <alisaidi@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com
Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 01cfcde9c26d8555f0e6e9aea9d6049f87683998 upstream.
task_h_load() can return 0 in some situations like running stress-ng
mmapfork, which forks thousands of threads, in a sched group on a 224 cores
system. The load balance doesn't handle this correctly because
env->imbalance never decreases and it will stop pulling tasks only after
reaching loop_max, which can be equal to the number of running tasks of
the cfs. Make sure that imbalance will be decreased by at least 1.
misfit task is the other feature that doesn't handle correctly such
situation although it's probably more difficult to face the problem
because of the smaller number of CPUs and running tasks on heterogenous
system.
We can't simply ensure that task_h_load() returns at least one because it
would imply to handle underflow in other places.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: <stable@vger.kernel.org> # v4.4+
Link: https://lkml.kernel.org/r/20200710152426.16981-1-vincent.guittot@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[PG: use v5.4.x-stable version instead of mainline.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ce3614daabea8a2d01c1dd17ae41d1ec5e5ae7db upstream.
While integrating rseq into glibc and replacing glibc's sched_getcpu
implementation with rseq, glibc's tests discovered an issue with
incorrect __rseq_abi.cpu_id field value right after the first time
a newly created process issues sched_setaffinity.
For the records, it triggers after building glibc and running tests, and
then issuing:
for x in {1..2000} ; do posix/tst-affinity-static & done
and shows up as:
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 138, expected 0
error: Unexpected CPU 138, expected 0
error: Unexpected CPU 138, expected 0
error: Unexpected CPU 138, expected 0
This is caused by the scheduler invoking __set_task_cpu() directly from
sched_fork() and wake_up_new_task(), thus bypassing rseq_migrate() which
is done by set_task_cpu().
Add the missing rseq_migrate() to both functions. The only other direct
use of __set_task_cpu() is done by init_idle(), which does not involve a
user-space task.
Based on my testing with the glibc test-case, just adding rseq_migrate()
to wake_up_new_task() is sufficient to fix the observed issue. Also add
it to sched_fork() to keep things consistent.
The reason why this never triggered so far with the rseq/basic_test
selftest is unclear.
The current use of sched_getcpu(3) does not typically require it to be
always accurate. However, use of the __rseq_abi.cpu_id field within rseq
critical sections requires it to be accurate. If it is not accurate, it
can cause corruption in the per-cpu data targeted by rseq critical
sections in user-space.
Reported-By: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-By: Florian Weimer <fweimer@redhat.com>
Cc: stable@vger.kernel.org # v4.18+
Link: https://lkml.kernel.org/r/20200707201505.2632-1-mathieu.desnoyers@efficios.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e2a71bdea81690b6ef11f4368261ec6f5b6891aa upstream.
When an expiration delta falls into the last level of the wheel, that delta
has be compared against the maximum possible delay and reduced to fit in if
necessary.
However instead of comparing the delta against the maximum, the code
compares the actual expiry against the maximum. Then instead of fixing the
delta to fit in, it sets the maximum delta as the expiry value.
This can result in various undesired outcomes, the worst possible one
being a timer expiring 15 days ahead to fire immediately.
Fixes: 500462a9de65 ("timers: Switch to a non-cascading wheel")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200717140551.29076-2-frederic@kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 30c66fc30ee7a98c4f3adf5fb7e213b61884474f upstream.
When a timer is enqueued with a negative delta (ie: expiry is below
base->clk), it gets added to the wheel as expiring now (base->clk).
Yet the value that gets stored in base->next_expiry, while calling
trigger_dyntick_cpu(), is the initial timer->expires value. The
resulting state becomes:
base->next_expiry < base->clk
On the next timer enqueue, forward_timer_base() may accidentally
rewind base->clk. As a possible outcome, timers may expire way too
early, the worst case being that the highest wheel levels get spuriously
processed again.
To prevent from that, make sure that base->next_expiry doesn't get below
base->clk.
Fixes: a683f390b93f ("timers: Forward the wheel clock whenever possible")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200703010657.2302-1-frederic@kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ad0f75e5f57ccbceec13274e1e242f2b5a6397ed upstream.
When we clone a socket in sk_clone_lock(), its sk_cgrp_data is
copied, so the cgroup refcnt must be taken too. And, unlike the
sk_alloc() path, sock_update_netprioidx() is not called here.
Therefore, it is safe and necessary to grab the cgroup refcnt
even when cgroup_sk_alloc is disabled.
sk_clone_lock() is in BH context anyway, the in_interrupt()
would terminate this function if called there. And for sk_alloc()
skcd->val is always zero. So it's safe to factor out the code
to make it more readable.
The global variable 'cgroup_sk_alloc_disabled' is used to determine
whether to take these reference counts. It is impossible to make
the reference counting correct unless we save this bit of information
in skcd->val. So, add a new bit there to record whether the socket
has already taken the reference counts. This obviously relies on
kmalloc() to align cgroup pointers to at least 4 bytes,
ARCH_KMALLOC_MINALIGN is certainly larger than that.
This bug seems to be introduced since the beginning, commit
d979a39d7242 ("cgroup: duplicate cgroup reference when cloning sockets")
tried to fix it but not compeletely. It seems not easy to trigger until
the recent commit 090e28b229af
("netprio_cgroup: Fix unlimited memory leak of v2 cgroups") was merged.
Fixes: bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup")
Reported-by: Cameron Berkenpas <cam@neo-zeon.de>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Reported-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reported-by: Daniël Sonck <dsonck92@gmail.com>
Reported-by: Zhang Qiang <qiang.zhang@windriver.com>
Tested-by: Cameron Berkenpas <cam@neo-zeon.de>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[PG: use 4.19.134-stable version instead of mainline.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 60f7bb66b88b649433bf700acfc60c3f24953871 upstream.
The kprobe show() functions were using "current"'s creds instead
of the file opener's creds for kallsyms visibility. Fix to use
seq_file->file->f_cred.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 81365a947de4 ("kprobes: Show address of kprobes if kallsyms does")
Fixes: ffb9bd68ebdb ("kprobes: Show blacklist addresses as same as kallsyms does")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b25a7c5af9051850d4f3d93ca500056ab6ec724b upstream.
The printing of section addresses in /sys/module/*/sections/* was not
using the correct credentials to evaluate visibility.
Before:
# cat /sys/module/*/sections/.*text
0xffffffffc0458000
...
# capsh --drop=CAP_SYSLOG -- -c "cat /sys/module/*/sections/.*text"
0xffffffffc0458000
...
After:
# cat /sys/module/*/sections/*.text
0xffffffffc0458000
...
# capsh --drop=CAP_SYSLOG -- -c "cat /sys/module/*/sections/.*text"
0x0000000000000000
...
Additionally replaces the existing (safe) /proc/modules check with
file->f_cred for consistency.
Reported-by: Dominik Czarnota <dominik.czarnota@trailofbits.com>
Fixes: be71eda5383f ("module: Fix display of wrong module .text address")
Cc: stable@vger.kernel.org
Tested-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ed66f991bb19d94cae5d38f77de81f96aac7813f upstream.
In order to gain access to the open file's f_cred for kallsym visibility
permission checks, refactor the module section attributes to use the
bin_attribute instead of attribute interface. Additionally removes the
redundant "name" struct member.
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 160251842cd35a75edfb0a1d76afa3eb674ff40a upstream.
In order to perform future tests against the cred saved during open(),
switch kallsyms_show_value() to operate on a cred, and have all current
callers pass current_cred(). This makes it very obvious where callers
are checking the wrong credential in their "read" contexts. These will
be fixed in the coming patches.
Additionally switch return value to bool, since it is always used as a
direct permission check, not a 0-on-success, negative-on-error style
function return.
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f227e3ec3b5cad859ad15666874405e8c1bbc1d4 upstream.
This modifies the first 32 bits out of the 128 bits of a random CPU's
net_rand_state on interrupt or CPU activity to complicate remote
observations that could lead to guessing the network RNG's internal
state.
Note that depending on some network devices' interrupt rate moderation
or binding, this re-seeding might happen on every packet or even almost
never.
In addition, with NOHZ some CPUs might not even get timer interrupts,
leaving their local state rarely updated, while they are running
networked processes making use of the random state. For this reason, we
also perform this update in update_process_times() in order to at least
update the state when there is user or system activity, since it's the
only case we care about.
Reported-by: Amit Klein <aksecurity@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 440ab9e10e2e6e5fd677473ee6f9e3af0f6904d6 upstream.
At times when I'm using kgdb I see a splat on my console about
suspicious RCU usage. I managed to come up with a case that could
reproduce this that looked like this:
WARNING: suspicious RCU usage
5.7.0-rc4+ #609 Not tainted
-----------------------------
kernel/pid.c:395 find_task_by_pid_ns() needs rcu_read_lock() protection!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by swapper/0/1:
#0: ffffff81b6b8e988 (&dev->mutex){....}-{3:3}, at: __device_attach+0x40/0x13c
#1: ffffffd01109e9e8 (dbg_master_lock){....}-{2:2}, at: kgdb_cpu_enter+0x20c/0x7ac
#2: ffffffd01109ea90 (dbg_slave_lock){....}-{2:2}, at: kgdb_cpu_enter+0x3ec/0x7ac
stack backtrace:
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 5.7.0-rc4+ #609
Hardware name: Google Cheza (rev3+) (DT)
Call trace:
dump_backtrace+0x0/0x1b8
show_stack+0x1c/0x24
dump_stack+0xd4/0x134
lockdep_rcu_suspicious+0xf0/0x100
find_task_by_pid_ns+0x5c/0x80
getthread+0x8c/0xb0
gdb_serial_stub+0x9d4/0xd04
kgdb_cpu_enter+0x284/0x7ac
kgdb_handle_exception+0x174/0x20c
kgdb_brk_fn+0x24/0x30
call_break_hook+0x6c/0x7c
brk_handler+0x20/0x5c
do_debug_exception+0x1c8/0x22c
el1_sync_handler+0x3c/0xe4
el1_sync+0x7c/0x100
rpmh_rsc_probe+0x38/0x420
platform_drv_probe+0x94/0xb4
really_probe+0x134/0x300
driver_probe_device+0x68/0x100
__device_attach_driver+0x90/0xa8
bus_for_each_drv+0x84/0xcc
__device_attach+0xb4/0x13c
device_initial_probe+0x18/0x20
bus_probe_device+0x38/0x98
device_add+0x38c/0x420
If I understand properly we should just be able to blanket kgdb under
one big RCU read lock and the problem should go away. We'll add it to
the beast-of-a-function known as kgdb_cpu_enter().
With this I no longer get any splats and things seem to work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200602154729.v2.1.I70e0d4fd46d5ed2aaf0c98a355e8e1b7a5bb7e4e@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9818427c6270a9ce8c52c8621026fe9cebae0f92 upstream.
Writing to the sysctl of a sched_domain->flags directly updates the value of
the field, and goes nowhere near update_top_cache_domain(). This means that
the cached domain pointers can end up containing stale data (e.g. the
domain pointed to doesn't have the relevant flag set anymore).
Explicit domain walks that check for flags will be affected by
the write, but this won't be in sync with the cached pointers which will
still point to the domains that were cached at the last sched_domain
build.
In other words, writing to this interface is playing a dangerous game. It
could be made to trigger an update of the cached sched_domain pointers when
written to, but this does not seem to be worth the trouble. Make it
read-only.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200415210512.805-3-valentin.schneider@arm.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 097350d1c6e1f5808cae142006f18a0bbc57018d upstream.
Currently the ring buffer makes events that happen in interrupts that preempt
another event have a delta of zero. (Hopefully we can change this soon). But
this is to deal with the races of updating a global counter with lockless
and nesting functions updating deltas.
With the addition of absolute time stamps, the time extend didn't follow
this rule. A time extend can happen if two events happen longer than 2^27
nanoseconds appart, as the delta time field in each event is only 27 bits.
If that happens, then a time extend is injected with 2^59 bits of
nanoseconds to use (18 years). But if the 2^27 nanoseconds happen between
two events, and as it is writing the event, an interrupt triggers, it will
see the 2^27 difference as well and inject a time extend of its own. But a
recent change made the time extend logic not take into account the nesting,
and this can cause two time extend deltas to happen moving the time stamp
much further ahead than the current time. This gets all reset when the ring
buffer moves to the next page, but that can cause time to appear to go
backwards.
This was observed in a trace-cmd recording, and since the data is saved in a
file, with trace-cmd report --debug, it was possible to see that this indeed
did happen!
bash-52501 110d... 81778.908247: sched_switch: bash:52501 [120] S ==> swapper/110:0 [120] [12770284:0x2e8:64]
<idle>-0 110d... 81778.908757: sched_switch: swapper/110:0 [120] R ==> bash:52501 [120] [509947:0x32c:64]
TIME EXTEND: delta:306454770 length:0
bash-52501 110.... 81779.215212: sched_swap_numa: src_pid=52501 src_tgid=52388 src_ngid=52501 src_cpu=110 src_nid=2 dst_pid=52509 dst_tgid=52388 dst_ngid=52501 dst_cpu=49 dst_nid=1 [0:0x378:48]
TIME EXTEND: delta:306458165 length:0
bash-52501 110dNh. 81779.521670: sched_wakeup: migration/110:565 [0] success=1 CPU:110 [0:0x3b4:40]
and at the next page, caused the time to go backwards:
bash-52504 110d... 81779.685411: sched_switch: bash:52504 [120] S ==> swapper/110:0 [120] [8347057:0xfb4:64]
CPU:110 [SUBBUFFER START] [81779379165886:0x1320000]
<idle>-0 110dN.. 81779.379166: sched_wakeup: bash:52504 [120] success=1 CPU:110 [0:0x10:40]
<idle>-0 110d... 81779.379167: sched_switch: swapper/110:0 [120] R ==> bash:52504 [120] [1168:0x3c:64]
Link: https://lkml.kernel.org/r/20200622151815.345d1bf5@oasis.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: stable@vger.kernel.org
Fixes: dc4e2801d400b ("ring-buffer: Redefine the unimplemented RINGBUF_TYPE_TIME_STAMP")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6784beada631800f2c5afd567e5628c843362cee upstream.
Fix the event trigger to accept redundant spaces in
the trigger input.
For example, these return -EINVAL
echo " traceon" > events/ftrace/print/trigger
echo "traceon if common_pid == 0" > events/ftrace/print/trigger
echo "disable_event:kmem:kmalloc " > events/ftrace/print/trigger
But these are hard to find what is wrong.
To fix this issue, use skip_spaces() to remove spaces
in front of actual tokens, and set NULL if there is no
token.
Link: http://lkml.kernel.org/r/159262476352.185015.5261566783045364186.stgit@devnote2
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 85f2b08268c0 ("tracing: Add basic event trigger framework")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1b0b283648163dae2a214ca28ed5a99f62a77319 upstream.
We use one blktrace per request_queue, that means one per the entire
disk. So we cannot run one blktrace on say /dev/vda and then /dev/vda1,
or just two calls on /dev/vda.
We check for concurrent setup only at the very end of the blktrace setup though.
If we try to run two concurrent blktraces on the same block device the
second one will fail, and the first one seems to go on. However when
one tries to kill the first one one will see things like this:
The kernel will show these:
```
debugfs: File 'dropped' in directory 'nvme1n1' already present!
debugfs: File 'msg' in directory 'nvme1n1' already present!
debugfs: File 'trace0' in directory 'nvme1n1' already present!
``
And userspace just sees this error message for the second call:
```
blktrace /dev/nvme1n1
BLKTRACESETUP(2) /dev/nvme1n1 failed: 5/Input/output error
```
The first userspace process #1 will also claim that the files
were taken underneath their nose as well. The files are taken
away form the first process given that when the second blktrace
fails, it will follow up with a BLKTRACESTOP and BLKTRACETEARDOWN.
This means that even if go-happy process #1 is waiting for blktrace
data, we *have* been asked to take teardown the blktrace.
This can easily be reproduced with break-blktrace [0] run_0005.sh test.
Just break out early if we know we're already going to fail, this will
prevent trying to create the files all over again, which we know still
exist.
[0] https://github.com/mcgrof/break-blktrace
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6743ad432ec92e680cd0d9db86cb17b949cf5a43 upstream.
Anders reported that the lockdep warns that suspicious
RCU list usage in register_kprobe() (detected by
CONFIG_PROVE_RCU_LIST.) This is because get_kprobe()
access kprobe_table[] by hlist_for_each_entry_rcu()
without rcu_read_lock.
If we call get_kprobe() from the breakpoint handler context,
it is run with preempt disabled, so this is not a problem.
But in other cases, instead of rcu_read_lock(), we locks
kprobe_mutex so that the kprobe_table[] is not updated.
So, current code is safe, but still not good from the view
point of RCU.
Joel suggested that we can silent that warning by passing
lockdep_is_held() to the last argument of
hlist_for_each_entry_rcu().
Add lockdep_is_held(&kprobe_mutex) at the end of the
hlist_for_each_entry_rcu() to suppress the warning.
Link: http://lkml.kernel.org/r/158927055350.27680.10261450713467997503.stgit@devnote2
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Suggested-by: Joel Fernandes <joel@joelfernandes.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 740797ce3a124b7dd22b7fb832d87bc8fba1cf6f upstream.
syzbot reported the following warning:
WARNING: CPU: 1 PID: 6351 at kernel/sched/deadline.c:628
enqueue_task_dl+0x22da/0x38a0 kernel/sched/deadline.c:1504
At deadline.c:628 we have:
623 static inline void setup_new_dl_entity(struct sched_dl_entity *dl_se)
624 {
625 struct dl_rq *dl_rq = dl_rq_of_se(dl_se);
626 struct rq *rq = rq_of_dl_rq(dl_rq);
627
628 WARN_ON(dl_se->dl_boosted);
629 WARN_ON(dl_time_before(rq_clock(rq), dl_se->deadline));
[...]
}
Which means that setup_new_dl_entity() has been called on a task
currently boosted. This shouldn't happen though, as setup_new_dl_entity()
is only called when the 'dynamic' deadline of the new entity
is in the past w.r.t. rq_clock and boosted tasks shouldn't verify this
condition.
Digging through the PI code I noticed that what above might in fact happen
if an RT tasks blocks on an rt_mutex hold by a DEADLINE task. In the
first branch of boosting conditions we check only if a pi_task 'dynamic'
deadline is earlier than mutex holder's and in this case we set mutex
holder to be dl_boosted. However, since RT 'dynamic' deadlines are only
initialized if such tasks get boosted at some point (or if they become
DEADLINE of course), in general RT 'dynamic' deadlines are usually equal
to 0 and this verifies the aforementioned condition.
Fix it by checking that the potential donor task is actually (even if
temporary because in turn boosted) running at DEADLINE priority before
using its 'dynamic' deadline value.
Fixes: 2d3d891d3344 ("sched/deadline: Add SCHED_DEADLINE inheritance logic")
Reported-by: syzbot+119ba87189432ead09b4@syzkaller.appspotmail.com
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Tested-by: Daniel Wagner <dwagner@suse.de>
Link: https://lkml.kernel.org/r/20181119153201.GB2119@localhost.localdomain
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ce9bc3b27f2a21a7969b41ffb04df8cf61bd1592 upstream.
syzbot reported the following warning triggered via SYSC_sched_setattr():
WARNING: CPU: 0 PID: 6973 at kernel/sched/deadline.c:593 setup_new_dl_entity /kernel/sched/deadline.c:594 [inline]
WARNING: CPU: 0 PID: 6973 at kernel/sched/deadline.c:593 enqueue_dl_entity /kernel/sched/deadline.c:1370 [inline]
WARNING: CPU: 0 PID: 6973 at kernel/sched/deadline.c:593 enqueue_task_dl+0x1c17/0x2ba0 /kernel/sched/deadline.c:1441
This happens because the ->dl_boosted flag is currently not initialized by
__dl_clear_params() (unlike the other flags) and setup_new_dl_entity()
rightfully complains about it.
Initialize dl_boosted to 0.
Fixes: 2d3d891d3344 ("sched/deadline: Add SCHED_DEADLINE inheritance logic")
Reported-by: syzbot+5ac8bac25f95e8b221e7@syzkaller.appspotmail.com
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Daniel Wagner <dwagner@suse.de>
Link: https://lkml.kernel.org/r/20200617072919.818409-1-juri.lelli@redhat.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9b38cc704e844e41d9cf74e647bff1d249512cb3 upstream.
Ziqian reported lockup when adding retprobe on _raw_spin_lock_irqsave.
My test was also able to trigger lockdep output:
============================================
WARNING: possible recursive locking detected
5.6.0-rc6+ #6 Not tainted
--------------------------------------------
sched-messaging/2767 is trying to acquire lock:
ffffffff9a492798 (&(kretprobe_table_locks[i].lock)){-.-.}, at: kretprobe_hash_lock+0x52/0xa0
but task is already holding lock:
ffffffff9a491a18 (&(kretprobe_table_locks[i].lock)){-.-.}, at: kretprobe_trampoline+0x0/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(kretprobe_table_locks[i].lock));
lock(&(kretprobe_table_locks[i].lock));
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by sched-messaging/2767:
#0: ffffffff9a491a18 (&(kretprobe_table_locks[i].lock)){-.-.}, at: kretprobe_trampoline+0x0/0x50
stack backtrace:
CPU: 3 PID: 2767 Comm: sched-messaging Not tainted 5.6.0-rc6+ #6
Call Trace:
dump_stack+0x96/0xe0
__lock_acquire.cold.57+0x173/0x2b7
? native_queued_spin_lock_slowpath+0x42b/0x9e0
? lockdep_hardirqs_on+0x590/0x590
? __lock_acquire+0xf63/0x4030
lock_acquire+0x15a/0x3d0
? kretprobe_hash_lock+0x52/0xa0
_raw_spin_lock_irqsave+0x36/0x70
? kretprobe_hash_lock+0x52/0xa0
kretprobe_hash_lock+0x52/0xa0
trampoline_handler+0xf8/0x940
? kprobe_fault_handler+0x380/0x380
? find_held_lock+0x3a/0x1c0
kretprobe_trampoline+0x25/0x50
? lock_acquired+0x392/0xbc0
? _raw_spin_lock_irqsave+0x50/0x70
? __get_valid_kprobe+0x1f0/0x1f0
? _raw_spin_unlock_irqrestore+0x3b/0x40
? finish_task_switch+0x4b9/0x6d0
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
The code within the kretprobe handler checks for probe reentrancy,
so we won't trigger any _raw_spin_lock_irqsave probe in there.
The problem is in outside kprobe_flush_task, where we call:
kprobe_flush_task
kretprobe_table_lock
raw_spin_lock_irqsave
_raw_spin_lock_irqsave
where _raw_spin_lock_irqsave triggers the kretprobe and installs
kretprobe_trampoline handler on _raw_spin_lock_irqsave return.
The kretprobe_trampoline handler is then executed with already
locked kretprobe_table_locks, and first thing it does is to
lock kretprobe_table_locks ;-) the whole lockup path like:
kprobe_flush_task
kretprobe_table_lock
raw_spin_lock_irqsave
_raw_spin_lock_irqsave ---> probe triggered, kretprobe_trampoline installed
---> kretprobe_table_locks locked
kretprobe_trampoline
trampoline_handler
kretprobe_hash_lock(current, &head, &flags); <--- deadlock
Adding kprobe_busy_begin/end helpers that mark code with fake
probe installed to prevent triggering of another kprobe within
this code.
Using these helpers in kprobe_flush_task, so the probe recursion
protection check is hit and the probe is never set to prevent
above lockup.
Link: http://lkml.kernel.org/r/158927059835.27680.7011202830041561604.stgit@devnote2
Fixes: ef53d9c5e4da ("kprobes: improve kretprobe scalability with hashed locking")
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "Gustavo A . R . Silva" <gustavoars@kernel.org>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: "Naveen N . Rao" <naveen.n.rao@linux.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Reported-by: "Ziqian SUN (Zamir)" <zsun@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1a0aa991a6274161c95a844c58cfb801d681eb59 upstream.
In kprobe_optimizer() kick_kprobe_optimizer() is called
without kprobe_mutex, but this can race with other caller
which is protected by kprobe_mutex.
To fix that, expand kprobe_mutex protected area to protect
kick_kprobe_optimizer() call.
Link: http://lkml.kernel.org/r/158927057586.27680.5036330063955940456.stgit@devnote2
Fixes: cd7ebe2298ff ("kprobes: Use text_poke_smp_batch for optimizing")
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "Gustavo A . R . Silva" <gustavoars@kernel.org>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: "Naveen N . Rao" <naveen.n.rao@linux.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ziqian SUN <zsun@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5aec598c456fe3c1b71a1202cbb42bdc2a643277 upstream.
The function blk_log_remap() can be simplified by removing the
call to get_pdu_remap() that copies the values into extra variable to
print the data, which also fixes the endiannness warning reported by
sparse.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 71df3fd82e7cccec7b749a8607a4662d9f7febdd upstream.
In function get_pdu_len() replace variable type from __u64 to
__be64. This fixes sparse warning.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 48bc3cd3e07a1486f45d9971c75d6090976c3b1b upstream.
In blk_add_trace_spliti() blk_add_trace_bio_remap() use
blk_status_to_errno() to pass the error instead of pasing the bi_status.
This fixes the sparse warning.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b5945214b76a1f22929481724ffd448000ede914 upstream.
cpu_pm_notify() is basically a wrapper of notifier_call_chain().
notifier_call_chain() doesn't initialize *nr_calls to 0 before it
starts incrementing it--presumably it's up to the callers to do this.
Unfortunately the callers of cpu_pm_notify() don't init *nr_calls.
This potentially means you could get too many or two few calls to
CPU_PM_ENTER_FAILED or CPU_CLUSTER_PM_ENTER_FAILED depending on the
luck of the stack.
Let's fix this.
Fixes: ab10023e0088 ("cpu_pm: Add cpu power management notifiers")
Cc: stable@vger.kernel.org
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200504104917.v6.3.I2d44fc0053d019f239527a4e5829416714b7e299@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1ea0f9120c8ce105ca181b070561df5cbd6bc049 upstream.
The map_lookup_and_delete_elem() function should check for both FMODE_CAN_WRITE
and FMODE_CAN_READ permissions because it returns a map element to user space.
Fixes: bd513cd08f10 ("bpf: add MAP_LOOKUP_AND_DELETE_ELEM syscall")
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200527185700.14658-5-a.s.protopopov@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d505b8af58912ae1e1a211fabc9995b19bd40828 upstream.
When users write some huge number into cpu.cfs_quota_us or
cpu.rt_runtime_us, overflow might happen during to_ratio() shifts of
schedulable checks.
to_ratio() could be altered to avoid unnecessary internal overflow, but
min_cfs_quota_period is less than 1 << BW_SHIFT, so a cutoff would still
be needed. Set a cap MAX_BW for cfs_quota_us and rt_runtime_us to
prevent overflow.
Signed-off-by: Huaixin Chang <changhuaixin@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Link: https://lkml.kernel.org/r/20200425105248.60093-1-changhuaixin@linux.alibaba.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bf2c59fce4074e55d622089b34be3a6bc95484fb upstream.
In the CPU-offline process, it calls mmdrop() after idle entry and the
subsequent call to cpuhp_report_idle_dead(). Once execution passes the
call to rcu_report_dead(), RCU is ignoring the CPU, which results in
lockdep complaining when mmdrop() uses RCU from either memcg or
debugobjects below.
Fix it by cleaning up the active_mm state from BP instead. Every arch
which has CONFIG_HOTPLUG_CPU should have already called idle_task_exit()
from AP. The only exception is parisc because it switches them to
&init_mm unconditionally (see smp_boot_one_cpu() and smp_cpu_init()),
but the patch will still work there because it calls mmgrab(&init_mm) in
smp_cpu_init() and then should call mmdrop(&init_mm) in finish_cpu().
WARNING: suspicious RCU usage
-----------------------------
kernel/workqueue.c:710 RCU or wq_pool_mutex should be held!
other info that might help us debug this:
RCU used illegally from offline CPU!
Call Trace:
dump_stack+0xf4/0x164 (unreliable)
lockdep_rcu_suspicious+0x140/0x164
get_work_pool+0x110/0x150
__queue_work+0x1bc/0xca0
queue_work_on+0x114/0x120
css_release+0x9c/0xc0
percpu_ref_put_many+0x204/0x230
free_pcp_prepare+0x264/0x570
free_unref_page+0x38/0xf0
__mmdrop+0x21c/0x2c0
idle_task_exit+0x170/0x1b0
pnv_smp_cpu_kill_self+0x38/0x2e0
cpu_die+0x48/0x64
arch_cpu_idle_dead+0x30/0x50
do_idle+0x2f4/0x470
cpu_startup_entry+0x38/0x40
start_secondary+0x7a8/0xa80
start_secondary_resume+0x10/0x14
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://lkml.kernel.org/r/20200401214033.8448-1-cai@lca.pw
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 586b58cac8b4683eb58a1446fbc399de18974e40 upstream.
With CONFIG_DEBUG_ATOMIC_SLEEP=y and CONFIG_CGROUPS=y, kernel oopses in
non-preemptible context look untidy; after the main oops, the kernel prints
a "sleeping function called from invalid context" report because
exit_signals() -> cgroup_threadgroup_change_begin() -> percpu_down_read()
can sleep, and that happens before the preempt_count_set(PREEMPT_ENABLED)
fixup.
It looks like the same thing applies to profile_task_exit() and
kcov_task_exit().
Fix it by moving the preemption fixup up and the calls to
profile_task_exit() and kcov_task_exit() down.
Fixes: 1dc0fffc48af ("sched/core: Robustify preemption leak checks")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200305220657.46800-1-jannh@google.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3054d06719079388a543de6adb812638675ad8f5 upstream.
If audit_list_rules_send() fails when trying to create a new thread
to send the rules it also fails to cleanup properly, leaking a
reference to a net structure. This patch fixes the error patch and
renames audit_send_list() to audit_send_list_thread() to better
match its cousin, audit_send_reply_thread().
Reported-by: teroincn@gmail.com
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a48b284b403a4a073d8beb72d2bb33e54df67fb6 upstream.
If audit_send_reply() fails when trying to create a new thread to
send the reply it also fails to cleanup properly, leaking a reference
to a net structure. This patch fixes the error path and makes a
handful of other cleanups that came up while fixing the code.
Reported-by: teroincn@gmail.com
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3ca676e4ca60d1834bb77535dafe24169cadacef upstream.
If we detect that we recursively entered the debugger we should hack
our I/O ops to NULL so that the panic() in the next line won't
actually cause another recursion into the debugger. The first line of
kgdb_panic() will check this and return.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.6.I89de39f68736c9de610e6f241e68d8dbc44bc266@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 202164fbfa2b2ffa3e66b504e0f126ba9a745006 upstream.
In commit 81eaadcae81b ("kgdboc: disable the console lock when in
kgdb") we avoided the WARN_CONSOLE_UNLOCKED() yell when we were in
kgdboc. That still works fine, but it turns out that we get a similar
yell when using other I/O drivers. One example is the "I/O driver"
for the kgdb test suite (kgdbts). When I enabled that I again got the
same yells.
Even though "kgdbts" doesn't actually interact with the user over the
console, using it still causes kgdb to print to the consoles. That
trips the same warning:
con_is_visible+0x60/0x68
con_scroll+0x110/0x1b8
lf+0x4c/0xc8
vt_console_print+0x1b8/0x348
vkdb_printf+0x320/0x89c
kdb_printf+0x68/0x90
kdb_main_loop+0x190/0x860
kdb_stub+0x2cc/0x3ec
kgdb_cpu_enter+0x268/0x744
kgdb_handle_exception+0x1a4/0x200
kgdb_compiled_brk_fn+0x34/0x44
brk_handler+0x7c/0xb8
do_debug_exception+0x1b4/0x228
Let's increment/decrement the "ignore_console_lock_warning" variable
all the time when we enter the debugger.
This will allow us to later revert commit 81eaadcae81b ("kgdboc:
disable the console lock when in kgdb").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.1.Ied2b058357152ebcc8bf68edd6f20a11d98d7d4e@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5a6d6a6ccb5f48ca8cf7c6d64ff83fd9c7999390 upstream.
In order to prevent possible hardlockup of sched_cfs_period_timer()
loop, loop count is introduced to denote whether to scale quota and
period or not. However, scale is done between forwarding period timer
and refilling cfs bandwidth runtime, which means that period timer is
forwarded with old "period" while runtime is refilled with scaled
"quota".
Move do_sched_cfs_period_timer() before scaling to solve this.
Fixes: 2e8e19226398 ("sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup")
Signed-off-by: Huaixin Chang <changhuaixin@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lkml.kernel.org/r/20200420024421.22442-3-changhuaixin@linux.alibaba.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2ed6edd33a214bca02bd2b45e3fc3038a059436b upstream.
Under rare circumstances, task_function_call() can repeatedly fail and
cause a soft lockup.
There is a slight race where the process is no longer running on the cpu
we targeted by the time remote_function() runs. The code will simply
try again. If we are very unlucky, this will continue to fail, until a
watchdog fires. This can happen in a heavily loaded, multi-core virtual
machine.
Reported-by: syzbot+bb4935a5c09b5ff79940@syzkaller.appspotmail.com
Signed-off-by: Barret Rhoden <brho@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200414222920.121401-1-brho@google.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 18f855e574d9799a0e7489f8ae6fd8447d0dd74a upstream.
Stefano reported a crash with using SQPOLL with io_uring:
BUG: kernel NULL pointer dereference, address: 00000000000003b0
CPU: 2 PID: 1307 Comm: io_uring-sq Not tainted 5.7.0-rc7 #11
RIP: 0010:task_numa_work+0x4f/0x2c0
Call Trace:
task_work_run+0x68/0xa0
io_sq_thread+0x252/0x3d0
kthread+0xf9/0x130
ret_from_fork+0x35/0x40
which is task_numa_work() oopsing on current->mm being NULL.
The task work is queued by task_tick_numa(), which checks if current->mm is
NULL at the time of the call. But this state isn't necessarily persistent,
if the kthread is using use_mm() to temporarily adopt the mm of a task.
Change the task_tick_numa() check to exclude kernel threads in general,
as it doesn't make sense to attempt ot balance for kthreads anyway.
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/865de121-8190-5d30-ece5-3b097dc74431@kernel.dk
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 30a35f79faadfeb1b89a7fdb3875f14063519041 upstream.
As Will Deacon points out, CONFIG_PROVE_LOCKING implies TRACE_IRQFLAGS,
so the conditions I added in the previous patch, and some others in the
same file can be simplified by only checking for the former.
No functional change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Yuyang Du <duyuyang@gmail.com>
Fixes: 886532aee3cd ("locking/lockdep: Move mark_lock() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING")
Link: https://lkml.kernel.org/r/20190628102919.2345242-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c0090c4c85c27d1fa3d785c935501b7207cd2869 upstream.
gcc warns that function print_lock_trace() is unused if
CONFIG_PROVE_LOCKING isn't set:
../kernel/locking/lockdep.c:2820:13: warning: ‘print_lock_trace’ defined but not used [-Wunused-function]
Rework so we remove the function if CONFIG_PROVE_LOCKING isn't set.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: will.deacon@arm.com
Fixes: c120bce78065 ("lockdep: Simplify stack trace handling")
Link: http://lkml.kernel.org/r/20190516191326.27003-1-anders.roxell@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
CONFIG_PROVE_LOCKING
commit 886532aee3cd42d95196601ed16d7c3d4679e9e5 upstream.
The last cleanup patch triggered another issue, as now another function
should be moved into the same section:
kernel/locking/lockdep.c:3580:12: error: 'mark_lock' defined but not used [-Werror=unused-function]
static int mark_lock(struct task_struct *curr, struct held_lock *this,
Move mark_lock() into the same #ifdef section as its only caller, and
remove the now-unused mark_lock_irq() stub helper.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yuyang Du <duyuyang@gmail.com>
Fixes: 0d2cc3b34532 ("locking/lockdep: Move valid_state() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING")
Link: https://lkml.kernel.org/r/20190617124718.1232976-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 091806515124b20f8cff7927b4b7ff399483b109 upstream.
Lock usage bit initialization is consolidated into one function
mark_usage(). Trivial readability improvement. No functional change.
Signed-off-by: Yuyang Du <duyuyang@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bvanassche@acm.org
Cc: frederic@kernel.org
Cc: ming.lei@redhat.com
Cc: will.deacon@arm.com
Link: https://lkml.kernel.org/r/20190506081939.74287-22-duyuyang@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 0354c1a3cdf31f44b035cfad14d32282e815a572 upstream.
While this doesn't actually amount to a real difference, since the macro
evaluates to the same thing, every place else operates on ktime_t using
these functions, so let's not break the pattern.
Fixes: e3ff9c3678b4 ("timekeeping: Repair ktime_get_coarse*() granularity")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-1-Jason@zx2c4.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2840eef0513c518faeb8a0ab8d07268c6285cdd0 upstream.
It appears the index beginning computation is not correct, the current
code does:
i = (irqts->count & IRQ_TIMINGS_MASK) - 1
If irqts->count is equal to zero, we end up with an index equal to -1,
but that does not happen because the function checks against zero
before and returns in such case.
However, if irqts->count is a multiple of IRQ_TIMINGS_SIZE, the
resulting & bit op will be zero and leads also to a -1 index.
Re-introduce the iteration loop belonging to the previous variance
code which was correct.
Fixes: bbba0e7c5cda "genirq/timings: Add array suffix computation code"
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20190527205521.12091-3-daniel.lezcano@linaro.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
Luis Chamberlain
Jan Kara
Greg Kroah-Hartman
Kees Cook
Thomas Gleixner
Vincent Guittot
Mathieu Desnoyers
Frederic Weisbecker
Cong Wang
Willy Tarreau
Douglas Anderson
Valentin Schneider
Steven Rostedt (VMware)
Masami Hiramatsu
Juri Lelli
Jiri Olsa
Chaitanya Kulkarni
Anton Protopopov
Huaixin Chang
Peter Zijlstra
Jann Horn
Paul Moore
Barret Rhoden
Jens Axboe
Arnd Bergmann
Anders Roxell
Yuyang Du
Jason A. Donenfeld
Daniel Lezcano