| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.12-rc8, including fixes from netfilter, and
bpf. BPF verifier changes stand out, otherwise things have slowed
down.
Current release - regressions:
- gro: ensure frag0 meets IP header alignment
- Revert "net: stmmac: re-init rx buffers when mac resume back"
- ethernet: macb: fix the restore of cmp registers
Previous releases - regressions:
- ixgbe: Fix NULL pointer dereference in ethtool loopback test
- ixgbe: fix unbalanced device enable/disable in suspend/resume
- phy: marvell: fix detection of PHY on Topaz switches
- make tcp_allowed_congestion_control readonly in non-init netns
- xen-netback: Check for hotplug-status existence before watching
Previous releases - always broken:
- bpf: mitigate a speculative oob read of up to map value size by
tightening the masking window
- sctp: fix race condition in sctp_destroy_sock
- sit, ip6_tunnel: Unregister catch-all devices
- netfilter: nftables: clone set element expression template
- netfilter: flowtable: fix NAT IPv6 offload mangling
- net: geneve: check skb is large enough for IPv4/IPv6 header
- netlink: don't call ->netlink_bind with table lock held"
* tag 'net-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
netlink: don't call ->netlink_bind with table lock held
MAINTAINERS: update my email
bpf: Update selftests to reflect new error states
bpf: Tighten speculative pointer arithmetic mask
bpf: Move sanitize_val_alu out of op switch
bpf: Refactor and streamline bounds check into helper
bpf: Improve verifier error messages for users
bpf: Rework ptr_limit into alu_limit and add common error path
bpf: Ensure off_reg has no mixed signed bounds for all types
bpf: Move off_reg into sanitize_ptr_alu
bpf: Use correct permission flag for mixed signed bounds arithmetic
ch_ktls: do not send snd_una update to TCB in middle
ch_ktls: tcb close causes tls connection failure
ch_ktls: fix device connection close
ch_ktls: Fix kernel panic
i40e: fix the panic when running bpf in xdpdrv mode
net/mlx5e: fix ingress_ifindex check in mlx5e_flower_parse_meta
net/mlx5e: Fix setting of RS FEC mode
net/mlx5: Fix setting of devlink traps in switchdev mode
Revert "net: stmmac: re-init rx buffers when mac resume back"
...
|
|
With clang-11+, the code is broken due to my kvmalloc() conversion
(which predated the clang-11 support code) leaving one vmalloc() in
place. Fix that.
Link: https://lkml.kernel.org/r/20210412214210.6e1ecca9cdc5.I24459763acf0591d5e6b31c7e3a59890d802f79c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2021-04-17
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 9 day(s) which contain
a total of 8 files changed, 175 insertions(+), 111 deletions(-).
The main changes are:
1) Fix a potential NULL pointer dereference in libbpf's xsk
umem handling, from Ciara Loftus.
2) Mitigate a speculative oob read of up to map value size by
tightening the masking window, from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This work tightens the offset mask we use for unprivileged pointer arithmetic
in order to mitigate a corner case reported by Piotr and Benedict where in
the speculative domain it is possible to advance, for example, the map value
pointer by up to value_size-1 out-of-bounds in order to leak kernel memory
via side-channel to user space.
Before this change, the computed ptr_limit for retrieve_ptr_limit() helper
represents largest valid distance when moving pointer to the right or left
which is then fed as aux->alu_limit to generate masking instructions against
the offset register. After the change, the derived aux->alu_limit represents
the largest potential value of the offset register which we mask against which
is just a narrower subset of the former limit.
For minimal complexity, we call sanitize_ptr_alu() from 2 observation points
in adjust_ptr_min_max_vals(), that is, before and after the simulated alu
operation. In the first step, we retieve the alu_state and alu_limit before
the operation as well as we branch-off a verifier path and push it to the
verification stack as we did before which checks the dst_reg under truncation,
in other words, when the speculative domain would attempt to move the pointer
out-of-bounds.
In the second step, we retrieve the new alu_limit and calculate the absolute
distance between both. Moreover, we commit the alu_state and final alu_limit
via update_alu_sanitation_state() to the env's instruction aux data, and bail
out from there if there is a mismatch due to coming from different verification
paths with different states.
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Reported-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Benedict Schlueter <benedict.schlueter@rub.de>
|
|
Add a small sanitize_needed() helper function and move sanitize_val_alu()
out of the main opcode switch. In upcoming work, we'll move sanitize_ptr_alu()
as well out of its opcode switch so this helps to streamline both.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move the bounds check in adjust_ptr_min_max_vals() into a small helper named
sanitize_check_bounds() in order to simplify the former a bit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Consolidate all error handling and provide more user-friendly error messages
from sanitize_ptr_alu() and sanitize_val_alu().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Small refactor with no semantic changes in order to consolidate the max
ptr_limit boundary check.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
The mixed signed bounds check really belongs into retrieve_ptr_limit()
instead of outside of it in adjust_ptr_min_max_vals(). The reason is
that this check is not tied to PTR_TO_MAP_VALUE only, but to all pointer
types that we handle in retrieve_ptr_limit() and given errors from the latter
propagate back to adjust_ptr_min_max_vals() and lead to rejection of the
program, it's a better place to reside to avoid anything slipping through
for future types. The reason why we must reject such off_reg is that we
otherwise would not be able to derive a mask, see details in 9d7eceede769
("bpf: restrict unknown scalars of mixed signed bounds for unprivileged").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Small refactor to drag off_reg into sanitize_ptr_alu(), so we later on can
use off_reg for generalizing some of the checks for all pointer types.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
We forbid adding unknown scalars with mixed signed bounds due to the
spectre v1 masking mitigation. Hence this also needs bypass_spec_v1
flag instead of allow_ptr_leaks.
Fixes: 2c78ee898d8f ("bpf: Implement CAP_BPF")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix a memory link in dyn_event_release().
An error path exited the function before freeing the allocated 'argv'
variable"
* tag 'trace-v5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/dynevent: Fix a memory leak in an error handling path
|
|
We must free 'argv' before returning, as already done in all the other
paths of this function.
Link: https://lkml.kernel.org/r/21e3594ccd7fc88c5c162c98450409190f304327.1618136448.git.christophe.jaillet@wanadoo.fr
Fixes: d262271d0483 ("tracing/dynevent: Delegate parsing to create function")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixlets from Ingo Molnar:
"Two minor fixes: one for a Clang warning, the other improves an
ambiguous/confusing kernel log message"
* tag 'locking-urgent-2021-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Address clang -Wformat warning printing for %hd
lockdep: Add a missing initialization hint to the "INFO: Trying to register non-static key" message
|
|
Merge misc fixes from Andrew Morton:
"14 patches.
Subsystems affected by this patch series: mm (kasan, gup, pagecache,
and kfence), MAINTAINERS, mailmap, nds32, gcov, ocfs2, ia64, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib: fix kconfig dependency on ARCH_WANT_FRAME_POINTERS
kfence, x86: fix preemptible warning on KPTI-enabled systems
lib/test_kasan_module.c: suppress unused var warning
kasan: fix conflict with page poisoning
fs: direct-io: fix missing sdio->boundary
ia64: fix user_stack_pointer() for ptrace()
ocfs2: fix deadlock between setattr and dio_end_io_write
gcov: re-fix clang-11+ support
nds32: flush_dcache_page: use page_mapping_file to avoid races with swapoff
mm/gup: check page posion status for coredump.
.mailmap: fix old email addresses
mailmap: update email address for Jordan Crouse
treewide: change my e-mail address, fix my name
MAINTAINERS: update CZ.NIC's Turris information
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.12-rc7, including fixes from can, ipsec,
mac80211, wireless, and bpf trees.
No scary regressions here or in the works, but small fixes for 5.12
changes keep coming.
Current release - regressions:
- virtio: do not pull payload in skb->head
- virtio: ensure mac header is set in virtio_net_hdr_to_skb()
- Revert "net: correct sk_acceptq_is_full()"
- mptcp: revert "mptcp: provide subflow aware release function"
- ethernet: lan743x: fix ethernet frame cutoff issue
- dsa: fix type was not set for devlink port
- ethtool: remove link_mode param and derive link params from driver
- sched: htb: fix null pointer dereference on a null new_q
- wireless: iwlwifi: Fix softirq/hardirq disabling in
iwl_pcie_enqueue_hcmd()
- wireless: iwlwifi: fw: fix notification wait locking
- wireless: brcmfmac: p2p: Fix deadlock introduced by avoiding the
rtnl dependency
Current release - new code bugs:
- napi: fix hangup on napi_disable for threaded napi
- bpf: take module reference for trampoline in module
- wireless: mt76: mt7921: fix airtime reporting and related tx hangs
- wireless: iwlwifi: mvm: rfi: don't lock mvm->mutex when sending
config command
Previous releases - regressions:
- rfkill: revert back to old userspace API by default
- nfc: fix infinite loop, refcount & memory leaks in LLCP sockets
- let skb_orphan_partial wake-up waiters
- xfrm/compat: Cleanup WARN()s that can be user-triggered
- vxlan, geneve: do not modify the shared tunnel info when PMTU
triggers an ICMP reply
- can: fix msg_namelen values depending on CAN_REQUIRED_SIZE
- can: uapi: mark union inside struct can_frame packed
- sched: cls: fix action overwrite reference counting
- sched: cls: fix err handler in tcf_action_init()
- ethernet: mlxsw: fix ECN marking in tunnel decapsulation
- ethernet: nfp: Fix a use after free in nfp_bpf_ctrl_msg_rx
- ethernet: i40e: fix receiving of single packets in xsk zero-copy
mode
- ethernet: cxgb4: avoid collecting SGE_QBASE regs during traffic
Previous releases - always broken:
- bpf: Refuse non-O_RDWR flags in BPF_OBJ_GET
- bpf: Refcount task stack in bpf_get_task_stack
- bpf, x86: Validate computation of branch displacements
- ieee802154: fix many similar syzbot-found bugs
- fix NULL dereferences in netlink attribute handling
- reject unsupported operations on monitor interfaces
- fix error handling in llsec_key_alloc()
- xfrm: make ipv4 pmtu check honor ip header df
- xfrm: make hash generation lock per network namespace
- xfrm: esp: delete NETIF_F_SCTP_CRC bit from features for esp
offload
- ethtool: fix incorrect datatype in set_eee ops
- xdp: fix xdp_return_frame() kernel BUG throw for page_pool memory
model
- openvswitch: fix send of uninitialized stack memory in ct limit
reply
Misc:
- udp: add get handling for UDP_GRO sockopt"
* tag 'net-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (182 commits)
net: fix hangup on napi_disable for threaded napi
net: hns3: Trivial spell fix in hns3 driver
lan743x: fix ethernet frame cutoff issue
net: ipv6: check for validity before dereferencing cfg->fc_nlinfo.nlh
net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits
net: dsa: lantiq_gswip: Don't use PHY auto polling
net: sched: sch_teql: fix null-pointer dereference
ipv6: report errors for iftoken via netlink extack
net: sched: fix err handler in tcf_action_init()
net: sched: fix action overwrite reference counting
Revert "net: sched: bump refcount for new action in ACT replace mode"
ice: fix memory leak of aRFS after resuming from suspend
i40e: Fix sparse warning: missing error code 'err'
i40e: Fix sparse error: 'vsi->netdev' could be null
i40e: Fix sparse error: uninitialized symbol 'ring'
i40e: Fix sparse errors in i40e_txrx.c
i40e: Fix parameters in aq_get_phy_register()
nl80211: fix beacon head validation
bpf, x86: Validate computation of branch displacements for x86-32
bpf, x86: Validate computation of branch displacements for x86-64
...
|
|
LLVM changed the expected function signature for llvm_gcda_emit_function()
in the clang-11 release. Users of clang-11 or newer may have noticed
their kernels producing invalid coverage information:
$ llvm-cov gcov -a -c -u -f -b <input>.gcda -- gcno=<input>.gcno
1 <func>: checksum mismatch, \
(<lineno chksum A>, <cfg chksum B>) != (<lineno chksum A>, <cfg chksum C>)
2 Invalid .gcda File!
...
Fix up the function signatures so calling this function interprets its
parameters correctly and computes the correct cfg checksum. In
particular, in clang-11, the additional checksum is no longer optional.
Link: https://reviews.llvm.org/rG25544ce2df0daa4304c07e64b9c8b0f7df60c11d
Link: https://lkml.kernel.org/r/20210408184631.1156669-1-ndesaulniers@google.com
Reported-by: Prasad Sodagudi <psodagud@quicinc.com>
Tested-by: Prasad Sodagudi <psodagud@quicinc.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
84;0;0c84;0;0c
There are two workqueue-specific watchdog timestamps:
+ @wq_watchdog_touched_cpu (per-CPU) updated by
touch_softlockup_watchdog()
+ @wq_watchdog_touched (global) updated by
touch_all_softlockup_watchdogs()
watchdog_timer_fn() checks only the global @wq_watchdog_touched for
unbound workqueues. As a result, unbound workqueues are not aware
of touch_softlockup_watchdog(). The watchdog might report a stall
even when the unbound workqueues are blocked by a known slow code.
Solution:
touch_softlockup_watchdog() must touch also the global @wq_watchdog_touched
timestamp.
The global timestamp can no longer be used for bound workqueues because
it is now updated from all CPUs. Instead, bound workqueues have to check
only @wq_watchdog_touched_cpu and these timestamps have to be updated for
all CPUs in touch_all_softlockup_watchdogs().
Beware:
The change might cause the opposite problem. An unbound workqueue
might get blocked on CPU A because of a real softlockup. The workqueue
watchdog would miss it when the timestamp got touched on CPU B.
It is acceptable because softlockups are detected by softlockup
watchdog. The workqueue watchdog is there to detect stalls where
a work never finishes, for example, because of dependencies of works
queued into the same workqueue.
V3:
- Modify the commit message clearly according to Petr's suggestion.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The debug_work_activate() is called on the premise that
the work can be inserted, because if wq be in WQ_DRAINING
status, insert work may be failed.
Fixes: e41e704bc4f4 ("workqueue: improve destroy_workqueue() debuggability")
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix stack trace entry size to stop showing garbage
The macro that creates both the structure and the format displayed to
user space for the stack trace event was changed a while ago to fix
the parsing by user space tooling. But this change also modified the
structure used to store the stack trace event. It changed the caller
array field from [0] to [8].
Even though the size in the ring buffer is dynamic and can be
something other than 8 (user space knows how to handle this), the 8
extra words was not accounted for when reserving the event on the ring
buffer, and added 8 more entries, due to the calculation of
"sizeof(*entry) + nr_entries * sizeof(long)", as the sizeof(*entry)
now contains 8 entries.
The size of the caller field needs to be subtracted from the size of
the entry to create the correct allocation size"
* tag 'trace-v5.12-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix stack trace event size
|
|
As for bpf_link, refuse creating a non-O_RDWR fd. Since program fds
currently don't allow modifications this is a precaution, not a
straight up bug fix.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210326160501.46234-2-lmb@cloudflare.com
|
|
Invoking BPF_OBJ_GET on a pinned bpf_link checks the path access
permissions based on file_flags, but the returned fd ignores flags.
This means that any user can acquire a "read-write" fd for a pinned
link with mode 0664 by invoking BPF_OBJ_GET with BPF_F_RDONLY in
file_flags. The fd can be used to invoke BPF_LINK_DETACH, etc.
Fix this by refusing non-O_RDWR flags in BPF_OBJ_GET. This works
because OBJ_GET by default returns a read write mapping and libbpf
doesn't expose a way to override this behaviour for programs
and links.
Fixes: 70ed506c3bbc ("bpf: Introduce pinnable bpf_link abstraction")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210326160501.46234-1-lmb@cloudflare.com
|
|
On x86 the struct pt_regs * grabbed by task_pt_regs() points to an
offset of task->stack. The pt_regs are later dereferenced in
__bpf_get_stack (e.g. by user_mode() check). This can cause a fault if
the task in question exits while bpf_get_task_stack is executing, as
warned by task_stack_page's comment:
* When accessing the stack of a non-current task that might exit, use
* try_get_task_stack() instead. task_stack_page will return a pointer
* that could get freed out from under you.
Taking the comment's advice and using try_get_task_stack() and
put_task_stack() to hold task->stack refcount, or bail early if it's
already 0. Incrementing stack_refcount will ensure the task's stack
sticks around while we're using its data.
I noticed this bug while testing a bpf task iter similar to
bpf_iter_task_stack in selftests, except mine grabbed user stack, and
getting intermittent crashes, which resulted in dumps like:
BUG: unable to handle page fault for address: 0000000000003fe0
\#PF: supervisor read access in kernel mode
\#PF: error_code(0x0000) - not-present page
RIP: 0010:__bpf_get_stack+0xd0/0x230
<snip...>
Call Trace:
bpf_prog_0a2be35c092cb190_get_task_stacks+0x5d/0x3ec
bpf_iter_run_prog+0x24/0x81
__task_seq_show+0x58/0x80
bpf_seq_read+0xf7/0x3d0
vfs_read+0x91/0x140
ksys_read+0x59/0xd0
do_syscall_64+0x48/0x120
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: fa28dcb82a38 ("bpf: Introduce helper bpf_get_task_stack()")
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210401000747.3648767-1-davemarchevsky@fb.com
|
|
Commit cbc3b92ce037 fixed an issue to modify the macros of the stack trace
event so that user space could parse it properly. Originally the stack
trace format to user space showed that the called stack was a dynamic
array. But it is not actually a dynamic array, in the way that other
dynamic event arrays worked, and this broke user space parsing for it. The
update was to make the array look to have 8 entries in it. Helper
functions were added to make it parse it correctly, as the stack was
dynamic, but was determined by the size of the event stored.
Although this fixed user space on how it read the event, it changed the
internal structure used for the stack trace event. It changed the array
size from [0] to [8] (added 8 entries). This increased the size of the
stack trace event by 8 words. The size reserved on the ring buffer was the
size of the stack trace event plus the number of stack entries found in
the stack trace. That commit caused the amount to be 8 more than what was
needed because it did not expect the caller field to have any size. This
produced 8 entries of garbage (and reading random data) from the stack
trace event:
<idle>-0 [002] d... 1976396.837549: <stack trace>
=> trace_event_raw_event_sched_switch
=> __traceiter_sched_switch
=> __schedule
=> schedule_idle
=> do_idle
=> cpu_startup_entry
=> secondary_startup_64_no_verify
=> 0xc8c5e150ffff93de
=> 0xffff93de
=> 0
=> 0
=> 0xc8c5e17800000000
=> 0x1f30affff93de
=> 0x00000004
=> 0x200000000
Instead, subtract the size of the caller field from the size of the event
to make sure that only the amount needed to store the stack trace is
reserved.
Link: https://lore.kernel.org/lkml/your-ad-here.call-01617191565-ext-9692@work.hours/
Cc: stable@vger.kernel.org
Fixes: cbc3b92ce037 ("tracing: Set kernel_stack's caller size properly")
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Tested-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Add check of order < 0 before calling free_pages()
The function addresses that are traced by ftrace are stored in pages,
and the size is held in a variable. If there's some error in creating
them, the allocate ones will be freed. In this case, it is possible
that the order of pages to be freed may end up being negative due to a
size of zero passed to get_count_order(), and then that negative
number will cause free_pages() to free a very large section.
Make sure that does not happen"
* tag 'trace-v5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Check if pages were allocated before calling free_pages()
|
|
It is possible that on error pg->size can be zero when getting its order,
which would return a -1 value. It is dangerous to pass in an order of -1
to free_pages(). Check if order is greater than or equal to zero before
calling free_pages().
Link: https://lore.kernel.org/lkml/20210330093916.432697c7@gandalf.local.home/
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Pull io_uring fixes from Jens Axboe:
- Use thread info versions of flag testing, as discussed last week.
- The series enabling PF_IO_WORKER to just take signals, instead of
needing to special case that they do not in a bunch of places. Ends
up being pretty trivial to do, and then we can revert all the special
casing we're currently doing.
- Kill dead pointer assignment
- Fix hashed part of async work queue trace
- Fix sign extension issue for IORING_OP_PROVIDE_BUFFERS
- Fix a link completion ordering regression in this merge window
- Cancellation fixes
* tag 'io_uring-5.12-2021-03-27' of git://git.kernel.dk/linux-block:
io_uring: remove unsued assignment to pointer io
io_uring: don't cancel extra on files match
io_uring: don't cancel-track common timeouts
io_uring: do post-completion chore on t-out cancel
io_uring: fix timeout cancel return code
Revert "signal: don't allow STOP on PF_IO_WORKER threads"
Revert "kernel: freezer should treat PF_IO_WORKER like PF_KTHREAD for freezing"
Revert "kernel: treat PF_IO_WORKER like PF_KTHREAD for ptrace/signals"
Revert "signal: don't allow sending any signals to PF_IO_WORKER threads"
kernel: stop masking signals in create_io_thread()
io_uring: handle signals for IO threads like a normal thread
kernel: don't call do_exit() for PF_IO_WORKER threads
io_uring: maintain CQE order of a failed link
io-wq: fix race around pending work on teardown
io_uring: do ctx sqd ejection in a clear context
io_uring: fix provide_buffers sign extension
io_uring: don't skip file_end_write() on reissue
io_uring: correct io_queue_async_work() traces
io_uring: don't use {test,clear}_tsk_thread_flag() for current
|
|
This reverts commit 4db4b1a0d1779dc159f7b87feb97030ec0b12597.
The IO threads allow and handle SIGSTOP now, so don't special case them
anymore in task_set_jobctl_pending().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 15b2219facadec583c24523eed40fa45865f859f.
Before IO threads accepted signals, the freezer using take signals to wake
up an IO thread would cause them to loop without any way to clear the
pending signal. That is no longer the case, so stop special casing
PF_IO_WORKER in the freezer.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 6fb8f43cede0e4bd3ead847de78d531424a96be9.
The IO threads do allow signals now, including SIGSTOP, and we can allow
ptrace attach. Attaching won't reveal anything interesting for the IO
threads, but it will allow eg gdb to attach to a task with io_urings
and IO threads without complaining. And once attached, it will allow
the usual introspection into regular threads.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 5be28c8f85ce99ed2d329d2ad8bdd18ea19473a5.
IO threads now take signals just fine, so there's no reason to limit them
specifically. Revert the change that prevented that from happening.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This is racy - move the blocking into when the task is created and
we're marking it as PF_IO_WORKER anyway. The IO threads are now
prepared to handle signals like SIGSTOP as well, so clear that from
the mask to allow proper stopping of IO threads.
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently module can be unloaded even if there's a trampoline
register in it. It's easily reproduced by running in parallel:
# while :; do ./test_progs -t module_attach; done
# while :; do rmmod bpf_testmod; sleep 0.5; done
Taking the module reference in case the trampoline's ip is
within the module code. Releasing it when the trampoline's
ip is unregistered.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210326105900.151466-1-jolsa@kernel.org
|
|
Right now we're never calling get_signal() from PF_IO_WORKER threads, but
in preparation for doing so, don't handle a fatal signal for them. The
workers have state they need to cleanup when exiting, so just return
instead of calling do_exit() on their behalf. The threads themselves will
detect a fatal signal and do proper shutdown.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an issue related to device links in the runtime PM framework
and debugfs usage in the Energy Model code.
Specifics:
- Modify the runtime PM device suspend to avoid suspending supplier
devices before the consumer device's status changes to
RPM_SUSPENDED (Rafael Wysocki)
- Change the Energy Model code to prevent it from attempting to
create its main debugfs directory too early (Lukasz Luba)"
* tag 'pm-5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: EM: postpone creating the debugfs dir till fs_initcall
PM: runtime: Defer suspending suppliers
|
|
The name string for BPF_XOR is "xor", not "or". Fix it.
Fixes: 981f94c3e921 ("bpf: Add bitwise atomic instructions")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Brendan Jackman <jackmanb@google.com>
Link: https://lore.kernel.org/bpf/20210325134141.8533-1-xukuohai@huawei.com
|
|
With the introduction of the struct_ops program type, it became possible to
implement kernel functionality in BPF, making it viable to use BPF in place
of a regular kernel module for these particular operations.
Thus far, the only user of this mechanism is for implementing TCP
congestion control algorithms. These are clearly marked as GPL-only when
implemented as modules (as seen by the use of EXPORT_SYMBOL_GPL for
tcp_register_congestion_control()), so it seems like an oversight that this
was not carried over to BPF implementations. Since this is the only user
of the struct_ops mechanism, just enforcing GPL-only for the struct_ops
program type seems like the simplest way to fix this.
Fixes: 0baf26b0fcd7 ("bpf: tcp: Support tcp_congestion_ops in bpf")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210326100314.121853-1-toke@redhat.com
|
|
Merge misc fixes from Andrew Morton:
"14 patches.
Subsystems affected by this patch series: mm (hugetlb, kasan, gup,
selftests, z3fold, kfence, memblock, and highmem), squashfs, ia64,
gcov, and mailmap"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mailmap: update Andrey Konovalov's email address
mm/highmem: fix CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP
mm: memblock: fix section mismatch warning again
kfence: make compatible with kmemleak
gcov: fix clang-11+ support
ia64: fix format strings for err_inject
ia64: mca: allocate early mca with GFP_ATOMIC
squashfs: fix xattr id and id lookup sanity checks
squashfs: fix inode lookup sanity checks
z3fold: prevent reclaim/free race for headless pages
selftests/vm: fix out-of-tree build
mm/mmu_notifiers: ensure range_end() is paired with range_start()
kasan: fix per-page tags for non-page_alloc pages
hugetlb_cgroup: fix imbalanced css_get and css_put pair for shared mappings
|
|
LLVM changed the expected function signatures for llvm_gcda_start_file()
and llvm_gcda_emit_function() in the clang-11 release. Users of
clang-11 or newer may have noticed their kernels failing to boot due to
a panic when enabling CONFIG_GCOV_KERNEL=y +CONFIG_GCOV_PROFILE_ALL=y.
Fix up the function signatures so calling these functions doesn't panic
the kernel.
Link: https://reviews.llvm.org/rGcdd683b516d147925212724b09ec6fb792a40041
Link: https://reviews.llvm.org/rG13a633b438b6500ecad9e4f936ebadf3411d0f44
Link: https://lkml.kernel.org/r/20210312224132.3413602-2-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Prasad Sodagudi <psodagud@quicinc.com>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Fangrui Song <maskray@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
"Various fixes, all over:
1) Fix overflow in ptp_qoriq_adjfine(), from Yangbo Lu.
2) Always store the rx queue mapping in veth, from Maciej
Fijalkowski.
3) Don't allow vmlinux btf in map_create, from Alexei Starovoitov.
4) Fix memory leak in octeontx2-af from Colin Ian King.
5) Use kvalloc in bpf x86 JIT for storing jit'd addresses, from
Yonghong Song.
6) Fix tx ptp stats in mlx5, from Aya Levin.
7) Check correct ip version in tun decap, fropm Roi Dayan.
8) Fix rate calculation in mlx5 E-Switch code, from arav Pandit.
9) Work item memork leak in mlx5, from Shay Drory.
10) Fix ip6ip6 tunnel crash with bpf, from Daniel Borkmann.
11) Lack of preemptrion awareness in macvlan, from Eric Dumazet.
12) Fix data race in pxa168_eth, from Pavel Andrianov.
13) Range validate stab in red_check_params(), from Eric Dumazet.
14) Inherit vlan filtering setting properly in b53 driver, from
Florian Fainelli.
15) Fix rtnl locking in igc driver, from Sasha Neftin.
16) Pause handling fixes in igc driver, from Muhammad Husaini
Zulkifli.
17) Missing rtnl locking in e1000_reset_task, from Vitaly Lifshits.
18) Use after free in qlcnic, from Lv Yunlong.
19) fix crash in fritzpci mISDN, from Tong Zhang.
20) Premature rx buffer reuse in igb, from Li RongQing.
21) Missing termination of ip[a driver message handler arrays, from
Alex Elder.
22) Fix race between "x25_close" and "x25_xmit"/"x25_rx" in hdlc_x25
driver, from Xie He.
23) Use after free in c_can_pci_remove(), from Tong Zhang.
24) Uninitialized variable use in nl80211, from Jarod Wilson.
25) Off by one size calc in bpf verifier, from Piotr Krysiuk.
26) Use delayed work instead of deferrable for flowtable GC, from
Yinjun Zhang.
27) Fix infinite loop in NPC unmap of octeontx2 driver, from
Hariprasad Kelam.
28) Fix being unable to change MTU of dwmac-sun8i devices due to lack
of fifo sizes, from Corentin Labbe.
29) DMA use after free in r8169 with WoL, fom Heiner Kallweit.
30) Mismatched prototypes in isdn-capi, from Arnd Bergmann.
31) Fix psample UAPI breakage, from Ido Schimmel"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (171 commits)
psample: Fix user API breakage
math: Export mul_u64_u64_div_u64
ch_ktls: fix enum-conversion warning
octeontx2-af: Fix memory leak of object buf
ptp_qoriq: fix overflow in ptp_qoriq_adjfine() u64 calcalation
net: bridge: don't notify switchdev for local FDB addresses
net/sched: act_ct: clear post_ct if doing ct_clear
net: dsa: don't assign an error value to tag_ops
isdn: capi: fix mismatched prototypes
net/mlx5: SF, do not use ecpu bit for vhca state processing
net/mlx5e: Fix division by 0 in mlx5e_select_queue
net/mlx5e: Fix error path for ethtool set-priv-flag
net/mlx5e: Offload tuple rewrite for non-CT flows
net/mlx5e: Allow to match on MPLS parameters only for MPLS over UDP
net/mlx5: Add back multicast stats for uplink representor
net: ipconfig: ic_dev can be NULL in ic_close_devs
MAINTAINERS: Combine "QLOGIC QLGE 10Gb ETHERNET DRIVER" sections into one
docs: networking: Fix a typo
r8169: fix DMA being used after buffer free if WoL is enabled
net: ipa: fix init header command validation
...
|
|
The debugfs directory '/sys/kernel/debug/energy_model' is needed before
the Energy Model registration can happen. With the recent change in
debugfs subsystem it's not allowed to create this directory at early
stage (core_initcall). Thus creating this directory would fail.
Postpone the creation of the EM debug dir to later stage: fs_initcall.
It should be safe since all clients: CPUFreq drivers, Devfreq drivers
will be initialized in later stages.
The custom debug log below prints the time of creation the EM debug dir
at fs_initcall and successful registration of EMs at later stages.
[ 1.505717] energy_model: creating rootdir
[ 3.698307] cpu cpu0: EM: created perf domain
[ 3.709022] cpu cpu1: EM: created perf domain
Fixes: 56348560d495 ("debugfs: do not attempt to create a new file before the filesystem is initalized")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Clang doesn't like format strings that truncate a 32-bit
value to something shorter:
kernel/locking/lockdep.c:709:4: error: format specifies type 'short' but the argument has type 'int' [-Werror,-Wformat]
In this case, the warning is a slightly questionable, as it could realize
that both class->wait_type_outer and class->wait_type_inner are in fact
8-bit struct members, even though the result of the ?: operator becomes an
'int'.
However, there is really no point in printing the number as a 16-bit
'short' rather than either an 8-bit or 32-bit number, so just change
it to a normal %d.
Fixes: de8f5e4f2dc1 ("lockdep: Introduce wait-type checks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210322115531.3987555-1-arnd@kernel.org
|
|
Pull io_uring followup fixes from Jens Axboe:
- The SIGSTOP change from Eric, so we properly ignore that for
PF_IO_WORKER threads.
- Disallow sending signals to PF_IO_WORKER threads in general, we're
not interested in having them funnel back to the io_uring owning
task.
- Stable fix from Stefan, ensuring we properly break links for short
send/sendmsg recv/recvmsg if MSG_WAITALL is set.
- Catch and loop when needing to run task_work before a PF_IO_WORKER
threads goes to sleep.
* tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block:
io_uring: call req_set_fail_links() on short send[msg]()/recv[msg]() with MSG_WAITALL
io-wq: ensure task is running before processing task_work
signal: don't allow STOP on PF_IO_WORKER threads
signal: don't allow sending any signals to PF_IO_WORKER threads
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"A change to robustify force-threaded IRQ handlers to always disable
interrupts, plus a DocBook fix.
The force-threaded IRQ handler change has been accelerated from the
normal schedule of such a change to keep the bad pattern/workaround of
spin_lock_irqsave() in handlers or IRQF_NOTHREAD as a kludge from
spreading"
* tag 'irq-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Disable interrupts for force threaded handlers
genirq/irq_sim: Fix typos in kernel doc (fnode -> fwnode)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
- Get static calls & modules right. Hopefully.
- WW mutex fixes
* tag 'locking-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
static_call: Fix static_call_update() sanity check
static_call: Align static_call_is_init() patching condition
static_call: Fix static_call_set_init()
locking/ww_mutex: Fix acquire/release imbalance in ww_acquire_init()/ww_acquire_fini()
locking/ww_mutex: Simplify use_ww_ctx & ww_ctx handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"The freshest pile of shiny x86 fixes for 5.12:
- Add the arch-specific mapping between physical and logical CPUs to
fix devicetree-node lookups
- Restore the IRQ2 ignore logic
- Fix get_nr_restart_syscall() to return the correct restart syscall
number. Split in a 4-patches set to avoid kABI breakage when
backporting to dead kernels"
* tag 'x86_urgent_for_v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/of: Fix CPU devicetree-node lookups
x86/ioapic: Ignore IRQ2 again
x86: Introduce restart_block->arch_data to remove TS_COMPAT_RESTART
x86: Introduce TS_COMPAT_RESTART to fix get_nr_restart_syscall()
x86: Move TS_COMPAT back to asm/thread_info.h
kernel, fs: Introduce and use set_restart_fn() and arch_set_restart_data()
|
|
Just like we don't allow normal signals to IO threads, don't deliver a
STOP to a task that has PF_IO_WORKER set. The IO threads don't take
signals in general, and have no means of flushing out a stop either.
Longer term, we may want to look into allowing stop of these threads,
as it relates to eg process freezing. For now, this prevents a spin
issue if a SIGSTOP is delivered to the parent task.
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
They don't take signals individually, and even if they share signals with
the parent task, don't allow them to be delivered through the worker
thread. Linux does allow this kind of behavior for regular threads, but
it's really a compatability thing that we need not care about for the IO
threads.
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
non-static key" message
Since this message is printed when dynamically allocated spinlocks (e.g.
kzalloc()) are used without initialization (e.g. spin_lock_init()),
suggest to developers to check whether initialization functions for objects
were called, before making developers wonder what annotation is missing.
[ mingo: Minor tweaks to the message. ]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210321064913.4619-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
With interrupt force threading all device interrupt handlers are invoked
from kernel threads. Contrary to hard interrupt context the invocation only
disables bottom halfs, but not interrupts. This was an oversight back then
because any code like this will have an issue:
thread(irq_A)
irq_handler(A)
spin_lock(&foo->lock);
interrupt(irq_B)
irq_handler(B)
spin_lock(&foo->lock);
This has been triggered with networking (NAPI vs. hrtimers) and console
drivers where printk() happens from an interrupt which interrupted the
force threaded handler.
Now people noticed and started to change the spin_lock() in the handler to
spin_lock_irqsave() which affects performance or add IRQF_NOTHREAD to the
interrupt request which in turn breaks RT.
Fix the root cause and not the symptom and disable interrupts before
invoking the force threaded handler which preserves the regular semantics
and the usefulness of the interrupt force threading as a general debugging
tool.
For not RT this is not changing much, except that during the execution of
the threaded handler interrupts are delayed until the handler
returns. Vs. scheduling and softirq processing there is no difference.
For RT kernels there is no issue.
Fixes: 8d32a307e4fa ("genirq: Provide forced interrupt threading")
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210317143859.513307808@linutronix.de
|
Linus Torvalds
Johannes Berg
David S. Miller
Daniel Borkmann
Christophe JAILLET
Nick Desaulniers
Wang Qing
Zqiang
Lorenz Bauer
Dave Marchevsky
Steven Rostedt (VMware)
Jens Axboe
Jiri Olsa
Xu Kuohai
Toke Høiland-Jørgensen
Lukasz Luba
Arnd Bergmann
Eric W. Biederman
Tetsuo Handa
Thomas Gleixner