| Age | Commit message (Collapse) | Author |
|---|
|
commit a092b7233f0e000cc6f2c71a49e2ecc6f917a5fc upstream.
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8048822bac01936fda2c7b924a52131da81e6198 upstream.
commit b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
Fixes: b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-8-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebfa440ce38b7e2e04c3124aa89c8a9f4094cf21 upstream.
SR-IOV VFs do not implement the memory enable bit of the command
register, therefore this bit is not set in config space after
pci_enable_device(). This leads to an unintended difference
between PF and VF in hand-off state to the user. We can correct
this by setting the initial value of the memory enable bit in our
virtualized config space. There's really no need however to
ever fault a user on a VF though as this would only indicate an
error in the user's management of the enable bit, versus a PF
where the same access could trigger hardware faults.
Fixes: abafbc551fdd ("vfio-pci: Invalidate mmaps and block MMIO access on disabled memory")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a653b205f29b3f9827a01a0c88bfbcb0d169494 upstream.
The following error ocurred when testing disk online/offline:
[ 301.798344] device-mapper: thin: 253:5: aborting current metadata transaction
[ 301.848441] device-mapper: thin: 253:5: failed to abort metadata transaction
[ 301.849206] Aborting journal on device dm-26-8.
[ 301.850489] EXT4-fs error (device dm-26) in __ext4_new_inode:943: Journal has aborted
[ 301.851095] EXT4-fs (dm-26): Delayed block allocation failed for inode 398742 at logical offset 181 with max blocks 19 with error 30
[ 301.854476] BUG: KASAN: use-after-free in dm_bm_set_read_only+0x3a/0x40 [dm_persistent_data]
Reason is:
metadata_operation_failed
abort_transaction
dm_pool_abort_metadata
__create_persistent_data_objects
r = __open_or_format_metadata
if (r) --> If failed will free pmd->bm but pmd->bm not set NULL
dm_block_manager_destroy(pmd->bm);
set_pool_mode
dm_pool_metadata_read_only(pool->pmd);
dm_bm_set_read_only(pmd->bm); --> use-after-free
Add checks to see if pmd->bm is NULL in dm_bm_set_read_only and
dm_bm_set_read_write functions. If bm is NULL it means creating the
bm failed and so dm_bm_is_read_only must return true.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 219403d7e56f9b716ad80ab87db85d29547ee73e upstream.
Maybe __create_persistent_data_objects() caller will use PTR_ERR as a
pointer, it will lead to some strange things.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d16ff19e69ab57e08bf908faaacbceaf660249de upstream.
Maybe __create_persistent_data_objects() caller will use PTR_ERR as a
pointer, it will lead to some strange things.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7785a9e4c228db6d01086a52d5685cd7336a08b7 upstream.
Use the DECLARE_CRYPTO_WAIT() macro to properly initialize the crypto
wait structures declared on stack before their use with
crypto_wait_req().
Fixes: 39d13a1ac41d ("dm crypt: reuse eboiv skcipher for IV generation")
Fixes: bbb1658461ac ("dm crypt: Implement Elephant diffuser for Bitlocker compatibility")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e27fec66f0a94e35a35548bd0b29ae616e62ec62 upstream.
The dm-integrity target did not report errors in bitmap mode just after
creation. The reason is that the function integrity_recalc didn't clean up
ic->recalc_bitmap as it proceeded with recalculation.
Fix this by updating the bitmap accordingly -- the double shift serves
to rounddown.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 468dfca38b1a ("dm integrity: add a bitmap mode")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c322ee9320eaa4013ca3620b1130992916b19b31 upstream.
Commit 935fcc56abc3 ("dm mpath: only flush workqueue when needed")
changed flush_multipath_work() to avoid needless workqueue
flushing (of a multipath global workqueue). But that change didn't
realize the surrounding flush_multipath_work() code should also only
run if 'pg_init_in_progress' is set.
Fix this by only doing all of flush_multipath_work()'s PG init related
work if 'pg_init_in_progress' is set.
Otherwise multipath_wait_for_pg_init_completion() will run
unconditionally but the preceeding flush_workqueue(kmpath_handlerd)
may not. This could lead to deadlock (though only if kmpath_handlerd
never runs a corresponding work to decrement 'pg_init_in_progress').
It could also be, though highly unlikely, that the kmpath_handlerd
work that does PG init completes before 'pg_init_in_progress' is set,
and then an intervening DM table reload's multipath_postsuspend()
triggers flush_multipath_work().
Fixes: 935fcc56abc3 ("dm mpath: only flush workqueue when needed")
Cc: stable@vger.kernel.org
Reported-by: Ben Marzinski <bmarzins@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9e040efcc28309e5c592f7e79085a9a52e31f58 upstream.
The function dax_direct_access doesn't take partitions into account,
it always maps pages from the beginning of the device. Therefore,
persistent_memory_claim() must get the partition offset using
get_start_sect() and add it to the page offsets passed to
dax_direct_access().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 48debafe4f2f ("dm: add writecache target")
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 971df65cbf32da9bc9af52c1196ca504dd316086 upstream.
Normally softwareshutdowntemp should be greater than Thotspotlimit.
However, on some VEGA10 ASIC, the softwareshutdowntemp is 91C while
Thotspotlimit is 105C. This seems not right and may trigger some
false alarms.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05655541c9503bfd01af4e6cbd7f5a29ac748e6c upstream.
Fix the source and destination physical address calculation of a
peripheral device on scatter-gather implementation.
This issue manifested during tests using a 64 bits architecture system.
The abnormal behavior wasn't visible before due to all previous tests
were done using 32 bits architecture system, that masked his effect.
Fixes: e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/8d3ab7e2ba96563fe3495b32f60077fffb85307d.1597327623.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b5455636fe26ea21b4189d135a424a6da016418 upstream.
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Karthik Shivaram <karthikgs@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f0835d6677dc69263f90f976524cb92b257d9f4 upstream.
Only report uevent file contents if device still registered, else we
might read freed memory.
Reported-by: syzbot+ceef16277388d6f24898@syzkaller.appspotmail.com
Cc: Hillf Danton <hdanton@sina.com>
Cc: <stable@vger.kernel.org> # 4.16+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2e2d73fa28136598e84db9d021091f1b98cbb1a upstream.
Device drivers do not expect to have change_protocol or wakeup
re-programming to be accesed after rc_unregister_device(). This can
cause the device driver to access deallocated resources.
Cc: <stable@vger.kernel.org> # 4.16+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df57d73276b863af1debc48546b0e59e44998a55 upstream.
For Intel controllers, SDHCI_RESET_ALL resets also CQHCI registers.
Normally, SDHCI_RESET_ALL is not used while CQHCI is enabled, but that can
happen on the error path. e.g. if mmc_cqe_recovery() fails, mmc_blk_reset()
is called which, for a eMMC that does not support HW Reset, will cycle the
bus power and the driver will perform SDHCI_RESET_ALL.
So whenever performing SDHCI_RESET_ALL ensure CQHCI is deactivated.
That will force the driver to reinitialize CQHCI when it is next used.
A similar change was done already for sdhci-msm, and other drivers using
CQHCI might benefit from a similar change, if they also have CQHCI reset
by SDHCI_RESET_ALL.
Fixes: 8ee82bda230fc9 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Cc: stable@vger.kernel.org # 5.4.x: 0ffa6cfbd949: mmc: cqhci: Add cqhci_deactivate()
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819121848.16967-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ffa6cfbd94982e6c028a8924b06a96c1b91bed8 upstream.
Host controllers can reset CQHCI either directly or as a consequence of
host controller reset. Add cqhci_deactivate() which puts the CQHCI
driver into a state that is consistent with that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583503724-13943-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 855d388df217989fbf1f18c781ae6490dbb48e86 upstream.
This patch fixs eMMC-Access on mt7622/Bpi-64.
Before we got these Errors on mounting eMMC ion R64:
[ 48.664925] blk_update_request: I/O error, dev mmcblk0, sector 204800 op 0x1:(WRITE)
flags 0x800 phys_seg 1 prio class 0
[ 48.676019] Buffer I/O error on dev mmcblk0p1, logical block 0, lost sync page write
This patch adds a optional reset management for msdc.
Sometimes the bootloader does not bring msdc register
to default state, so need reset the msdc controller.
Cc: <stable@vger.kernel.org> # v5.4+
Fixes: 966580ad236e ("mmc: mediatek: add support for MT7622 SoC")
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200814014346.6496-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d55dad8b1d893fae0c4e778abf2ace048bcbad86.
Upstream commit af199a1a9cb0 ("net: dsa: microchip: set the correct
number of ports") seems to have been applied twice on top of the 5.4
branch. This revert the second instance of said commit.
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 29aaebbca4abc4cceb38738483051abefafb6950 upstream.
Beware that the address size for x86-32 may exceed unsigned long.
[ 0.368971] UBSAN: shift-out-of-bounds in drivers/iommu/intel/iommu.c:128:14
[ 0.369055] shift exponent 36 is too large for 32-bit type 'long unsigned int'
If we don't handle the wide addresses, the pages are mismapped and the
device read/writes go astray, detected as DMAR faults and leading to
device failure. The behaviour changed (from working to broken) in commit
fa954e683178 ("iommu/vt-d: Delegate the dma domain to upper layer"), but
the error looks older.
Fixes: fa954e683178 ("iommu/vt-d: Delegate the dma domain to upper layer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: James Sewart <jamessewart@arista.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://lore.kernel.org/r/20200822160209.28512-1-chris@chris-wilson.co.uk
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit abafbc551fddede3e0a08dee1dcde08fc0eb8476 upstream.
Accessing the disabled memory space of a PCI device would typically
result in a master abort response on conventional PCI, or an
unsupported request on PCI express. The user would generally see
these as a -1 response for the read return data and the write would be
silently discarded, possibly with an uncorrected, non-fatal AER error
triggered on the host. Some systems however take it upon themselves
to bring down the entire system when they see something that might
indicate a loss of data, such as this discarded write to a disabled
memory space.
To avoid this, we want to try to block the user from accessing memory
spaces while they're disabled. We start with a semaphore around the
memory enable bit, where writers modify the memory enable state and
must be serialized, while readers make use of the memory region and
can access in parallel. Writers include both direct manipulation via
the command register, as well as any reset path where the internal
mechanics of the reset may both explicitly and implicitly disable
memory access, and manipulation of the MSI-X configuration, where the
MSI-X vector table resides in MMIO space of the device. Readers
include the read and write file ops to access the vfio device fd
offsets as well as memory mapped access. In the latter case, we make
use of our new vma list support to zap, or invalidate, those memory
mappings in order to force them to be faulted back in on access.
Our semaphore usage will stall user access to MMIO spaces across
internal operations like reset, but the user might experience new
behavior when trying to access the MMIO space while disabled via the
PCI command register. Access via read or write while disabled will
return -EIO and access via memory maps will result in a SIGBUS. This
is expected to be compatible with known use cases and potentially
provides better error handling capabilities than present in the
hardware, while avoiding the more readily accessible and severe
platform error responses that might otherwise occur.
Fixes: CVE-2020-12888
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 11c4cd07ba111a09f49625f9e4c851d83daf0a22 upstream.
Rather than calling remap_pfn_range() when a region is mmap'd, setup
a vm_ops handler to support dynamic faulting of the range on access.
This allows us to manage a list of vmas actively mapping the area that
we can later use to invalidate those mappings. The open callback
invalidates the vma range so that all tracking is inserted in the
fault handler and removed in the close handler.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 41311242221e3482b20bfed10fa4d9db98d87016 upstream.
With conversion to follow_pfn(), DMA mapping a PFNMAP range depends on
the range being faulted into the vma. Add support to manually provide
that, in the same way as done on KVM with hva_to_pfn_remapped().
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26e495f341075c09023ba16dee9a7f37a021e745 ]
Currently, the RemapEn (valid) bit is accidentally cleared when
programming IRTE w/ guestMode=0. It should be restored to
the prior state.
Fixes: b9fc6b56f478 ("iommu/amd: Implements irq_set_vcpu_affinity() hook to setup vapic mode for pass-through devices")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20200903093822.52012-2-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ffdab6f2dea9e23ec33230de24e492ff0b186d9 ]
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21d3c6e ("thermal: Add QPNP PMIC temperature alarm driver")
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30d24faba0532d6972df79a1bf060601994b5873 ]
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54d7 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e4e9ec65078093165463c13d4eb92b3e8d7b2e8 ]
The VT-d spec requires (10.4.4 Global Command Register, GCMD_REG General
Description) that:
If multiple control fields in this register need to be modified, software
must serialize the modifications through multiple writes to this register.
However, in irq_remapping.c, modifications of IRE and CFI are done in one
write. We need to do two separate writes with STS checking after each. It
also checks the status register before writing command register to avoid
unnecessary register write.
Fixes: af8d102f999a4 ("x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/20200828000615.8281-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 556699341efa98243e08e34401b3f601da91f5a3 ]
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eb0f3bc463d59d86402f19c59aa44e82dc3fab6d ]
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbedcb044e9cc4e14bbe6658111224bb923094f4 ]
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b6382a857d824c0866056d5736bbcb597a922ed ]
When multiple adapters are present in the system, pci hot-removing second
adapter leads to the following warning as both the adapters registered
thermal zone device with same thermal zone name/type.
Therefore, use unique thermal zone name during thermal zone device
initialization. Also mark thermal zone dev NULL once unregistered.
[ 414.370143] ------------[ cut here ]------------
[ 414.370944] sysfs group 'power' not found for kobject 'hwmon0'
[ 414.371747] WARNING: CPU: 9 PID: 2661 at fs/sysfs/group.c:281
sysfs_remove_group+0x76/0x80
[ 414.382550] CPU: 9 PID: 2661 Comm: bash Not tainted 5.8.0-rc6+ #33
[ 414.383593] Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.0a 06/23/2016
[ 414.384669] RIP: 0010:sysfs_remove_group+0x76/0x80
[ 414.385738] Code: 48 89 df 5b 5d 41 5c e9 d8 b5 ff ff 48 89 df e8 60 b0 ff ff
eb cb 49 8b 14 24 48 8b 75 00 48 c7 c7 90 ae 13 bb e8 6a 27 d0 ff <0f> 0b 5b 5d
41 5c c3 0f 1f 00 0f 1f 44 00 00 48 85 f6 74 31 41 54
[ 414.388404] RSP: 0018:ffffa22bc080fcb0 EFLAGS: 00010286
[ 414.389638] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 414.390829] RDX: 0000000000000001 RSI: ffff8ee2de3e9510 RDI: ffff8ee2de3e9510
[ 414.392064] RBP: ffffffffbaef2ee0 R08: 0000000000000000 R09: 0000000000000000
[ 414.393224] R10: 0000000000000000 R11: 000000002b30006c R12: ffff8ee260720008
[ 414.394388] R13: ffff8ee25e0a40e8 R14: ffffa22bc080ff08 R15: ffff8ee2c3be5020
[ 414.395661] FS: 00007fd2a7171740(0000) GS:ffff8ee2de200000(0000)
knlGS:0000000000000000
[ 414.396825] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 414.398011] CR2: 00007f178ffe5020 CR3: 000000084c5cc003 CR4: 00000000003606e0
[ 414.399172] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 414.400352] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 414.401473] Call Trace:
[ 414.402685] device_del+0x89/0x400
[ 414.403819] device_unregister+0x16/0x60
[ 414.405024] hwmon_device_unregister+0x44/0xa0
[ 414.406112] thermal_remove_hwmon_sysfs+0x196/0x200
[ 414.407256] thermal_zone_device_unregister+0x1b5/0x1f0
[ 414.408415] cxgb4_thermal_remove+0x3c/0x4f [cxgb4]
[ 414.409668] remove_one+0x212/0x290 [cxgb4]
[ 414.410875] pci_device_remove+0x36/0xb0
[ 414.412004] device_release_driver_internal+0xe2/0x1c0
[ 414.413276] pci_stop_bus_device+0x64/0x90
[ 414.414433] pci_stop_and_remove_bus_device_locked+0x16/0x30
[ 414.415609] remove_store+0x75/0x90
[ 414.416790] kernfs_fop_write+0x114/0x1b0
[ 414.417930] vfs_write+0xcf/0x210
[ 414.419059] ksys_write+0xa7/0xe0
[ 414.420120] do_syscall_64+0x4c/0xa0
[ 414.421278] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 414.422335] RIP: 0033:0x7fd2a686afd0
[ 414.423396] Code: Bad RIP value.
[ 414.424549] RSP: 002b:00007fffc1446148 EFLAGS: 00000246 ORIG_RAX:
0000000000000001
[ 414.425638] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd2a686afd0
[ 414.426830] RDX: 0000000000000002 RSI: 00007fd2a7196000 RDI: 0000000000000001
[ 414.427927] RBP: 00007fd2a7196000 R08: 000000000000000a R09: 00007fd2a7171740
[ 414.428923] R10: 00007fd2a7171740 R11: 0000000000000246 R12: 00007fd2a6b43400
[ 414.430082] R13: 0000000000000002 R14: 0000000000000001 R15: 0000000000000000
[ 414.431027] irq event stamp: 76300
[ 414.435678] ---[ end trace 13865acb4d5ab00f ]---
Fixes: b18719157762 ("cxgb4: Add thermal zone support")
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 192f6c29bb28bfd0a17e6ad331d09f1ec84143d0 ]
If the driver has to unbind from the controller for an early failure
before the subsystem has been set up, there won't be a subsystem holding
the controller's instance, so the controller needs to free its own
instance in this case.
Fixes: 733e4b69d508d ("nvme: Assign subsys instance from first ctrl")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70e37988db94aba607d5491a94f80ba08e399b6b ]
The way 'spin_lock()' and 'spin_lock_irqsave()' are used is not consistent
in this function.
Use 'spin_lock_irqsave()' also here, as there is no guarantee that
interruptions are disabled at that point, according to surrounding code.
Fixes: a97ec51b37ef ("nvmet_fc: Rework target side abort handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f272285f6abb9178d029375599626baf3d5f4e8a ]
Remove 1000baseT_Half to advertise correct hardware capability in
phylink_validate() callback function.
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b30063976f29fc221a99d18d37d22ca035068aa9 ]
The check for a required control in the request was missing a call to
v4l2_ctrl_request_hdl_put() in the error path. Fix it.
Fixes: 50e761516f2b8c ("media: platform: Add Cedrus VPU decoder driver")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e7c8fb8942773f412fe12f3b63e8bb92c18ab3f ]
The check for a required control in the request was missing a call to
v4l2_ctrl_request_hdl_put(), so the control request object was never
released.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 997deb811bf5 ("media: vicodec: Add support for stateless decoder.")
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96ecdcc992eb7f468b2cf829b0f5408a1fad4668 ]
Netpoll can try to poll napi as soon as napi_enable() is called.
It crashes trying to access a doorbell which is still NULL:
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S 5.9.0-rc1-00469-g5fd99b5d9950-dirty #26
RIP: 0010:bnxt_poll+0x121/0x1c0
Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02
41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a
netpoll_poll_dev+0xbd/0x1a0
__netpoll_send_skb+0x1b2/0x210
netpoll_send_udp+0x2c9/0x406
write_ext_msg+0x1d7/0x1f0
console_unlock+0x23c/0x520
vprintk_emit+0xe0/0x1d0
printk+0x58/0x6f
x86_vector_activate.cold+0xf/0x46
__irq_domain_activate_irq+0x50/0x80
__irq_domain_activate_irq+0x32/0x80
__irq_domain_activate_irq+0x32/0x80
irq_domain_activate_irq+0x25/0x40
__setup_irq+0x2d2/0x700
request_threaded_irq+0xfb/0x160
__bnxt_open_nic+0x3b1/0x750
bnxt_open_nic+0x19/0x30
ethtool_set_channels+0x1ac/0x220
dev_ethtool+0x11ba/0x2240
dev_ioctl+0x1cf/0x390
sock_do_ioctl+0x95/0x130
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12cce90b934bf2b0ed9c339b4d5503e69954351a ]
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9bb ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b148bb238c02f0c7797efed026e9bba5892d2172 ]
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit df3875ec550396974b1d8a518bd120d034738236 ]
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dbbfa96ad920c50d58bcaefa57f5f33ceef9d00e ]
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1c2d77408022a398a1a7c51cf20488c922629de ]
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd2d ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99d469fc64d06f0c81c0fe2a1c01645a67e0cbf0 ]
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b274e47d9e3f4dcd4ad4028a316ec22dc4533ac7 ]
During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0661cef675d37e2c4b66a996389ebeae8568e49e ]
Move the burst len fixup after setting the generic value for it. This
finally enables the fixup introduced by commit 137bd11090d8 ("dmaengine:
pl330: Align DMA memcpy operations to MFIFO width"), which otherwise was
overwritten by the generic value.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 137bd11090d8 ("dmaengine: pl330: Align DMA memcpy operations to MFIFO width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200825064617.16193-1-m.szyprowski@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2d79cd8875fa8c3cc7defa98a8cc99a1ed0c62f ]
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba03d ("net: arc_emac: support the phy reset for emac driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc ]
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ef1fc57301f3cef7201497aa27e89ccb91737fe ]
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8eb6 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 100e3345c6e719d2291e1efd5de311cc24bb9c0b ]
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 61d7437ed13906984c44697970ee792ac6271a31 ]
The AMD eMMC Controller can only use the tuned clock while in HS200 and
HS400 mode. If we switch to a different mode, we need to disable the
tuned clock. If we have previously performed tuning and switch back to
HS200 or HS400, we can re-enable the tuned clock.
Previously the tuned clock was not getting disabled when switching to
DDR52 which is part of the HS400 tuning sequence.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819125832.v2.1.Ie8f0689ec9f449203328b37409d1cf06b565f331@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Himadri Pandya
Sowjanya Komatineni
Alex Williamson
Ye Bin
Damien Le Moal
Mikulas Patocka
Mike Snitzer
Evan Quan
Gustavo Pimentel
Tejun Heo
Sean Young
Adrian Hunter
Wenbin Mei
Sasha Levin
Chris Wilson
Ajay Kaher
Suravee Suthikulpanit
Veera Vegivada
Tony Lindgren
Lu Baolu
Michael Chan
Dan Carpenter
Shung-Hsi Yu
Potnuri Bharat Teja
Keith Busch
Christophe JAILLET
Landen Chao
Ezequiel Garcia
Hans Verkuil
Jakub Kicinski
Edwin Peer
Vasundhara Volam
Pavan Chebbi
Murali Karicheri
Nicolas Dichtel
Marek Szyprowski
Dinghao Liu
Yuusuke Ashizuka
Raul E Rangel