| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.12-rc8, including fixes from netfilter, and
bpf. BPF verifier changes stand out, otherwise things have slowed
down.
Current release - regressions:
- gro: ensure frag0 meets IP header alignment
- Revert "net: stmmac: re-init rx buffers when mac resume back"
- ethernet: macb: fix the restore of cmp registers
Previous releases - regressions:
- ixgbe: Fix NULL pointer dereference in ethtool loopback test
- ixgbe: fix unbalanced device enable/disable in suspend/resume
- phy: marvell: fix detection of PHY on Topaz switches
- make tcp_allowed_congestion_control readonly in non-init netns
- xen-netback: Check for hotplug-status existence before watching
Previous releases - always broken:
- bpf: mitigate a speculative oob read of up to map value size by
tightening the masking window
- sctp: fix race condition in sctp_destroy_sock
- sit, ip6_tunnel: Unregister catch-all devices
- netfilter: nftables: clone set element expression template
- netfilter: flowtable: fix NAT IPv6 offload mangling
- net: geneve: check skb is large enough for IPv4/IPv6 header
- netlink: don't call ->netlink_bind with table lock held"
* tag 'net-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
netlink: don't call ->netlink_bind with table lock held
MAINTAINERS: update my email
bpf: Update selftests to reflect new error states
bpf: Tighten speculative pointer arithmetic mask
bpf: Move sanitize_val_alu out of op switch
bpf: Refactor and streamline bounds check into helper
bpf: Improve verifier error messages for users
bpf: Rework ptr_limit into alu_limit and add common error path
bpf: Ensure off_reg has no mixed signed bounds for all types
bpf: Move off_reg into sanitize_ptr_alu
bpf: Use correct permission flag for mixed signed bounds arithmetic
ch_ktls: do not send snd_una update to TCB in middle
ch_ktls: tcb close causes tls connection failure
ch_ktls: fix device connection close
ch_ktls: Fix kernel panic
i40e: fix the panic when running bpf in xdpdrv mode
net/mlx5e: fix ingress_ifindex check in mlx5e_flower_parse_meta
net/mlx5e: Fix setting of RS FEC mode
net/mlx5: Fix setting of devlink traps in switchdev mode
Revert "net: stmmac: re-init rx buffers when mac resume back"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"The largest change is for a regression that landed during -rc1 for
block-device read-only handling. Vaibhav found a new use for the
ability (originally introduced by virtio_pmem) to call back to the
platform to flush data, but also found an original bug in that
implementation. Lastly, Arnd cleans up some compile warnings in dax.
This has all appeared in -next with no reported issues.
Summary:
- Fix a regression of read-only handling in the pmem driver
- Fix a compile warning
- Fix support for platform cache flush commands on powerpc/papr"
* tag 'libnvdimm-fixes-for-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/region: Fix nvdimm_has_flush() to handle ND_REGION_ASYNC
libnvdimm: Notify disk drivers to revalidate region read-only
dax: avoid -Wempty-body warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL memory class fixes from Dan Williams:
"A collection of fixes for the CXL memory class driver introduced in
this release cycle.
The driver was primarily developed on a work-in-progress QEMU
emulation of the interface and we have since found a couple places
where it hid spec compliance bugs in the driver, or had a spec
implementation bug itself.
The biggest change here is replacing a percpu_ref with an rwsem to
cleanup a couple bugs in the error unwind path during ioctl device
init. Lastly there were some minor cleanups to not export the
power-management sysfs-ABI for the ioctl device, use the proper sysfs
helper for emitting values, and prevent subtle bugs as new
administration commands are added to the supported list.
The bulk of it has appeared in -next save for the top commit which was
found today and validated on a fixed-up QEMU model.
Summary:
- Fix support for CXL memory devices with registers offset from the
BAR base.
- Fix the reporting of device capacity.
- Fix the driver commands list definition to be disconnected from the
UAPI command list.
- Replace percpu_ref with rwsem to fix initialization error path.
- Fix leaks in the driver initialization error path.
- Drop the power/ directory from CXL device sysfs.
- Use the recommended sysfs helper for attribute 'show'
implementations"
* tag 'cxl-fixes-for-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/mem: Fix memory device capacity probing
cxl/mem: Fix register block offset calculation
cxl/mem: Force array size of mem_commands[] to CXL_MEM_COMMAND_ID_MAX
cxl/mem: Disable cxl device power management
cxl/mem: Do not rely on device_add() side effects for dev_set_name() failures
cxl/mem: Fix synchronization mechanism for device removal vs ioctl operations
cxl/mem: Use sysfs_emit() for attribute show routines
|
|
The CXL Identify Memory Device output payload emits capacity in 256MB
units. The driver is treating the capacity field as bytes. This was
missed because QEMU reports bytes when it should report bytes / 256MB.
Fixes: 8adaf747c9f0 ("cxl/mem: Find device capabilities")
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/161862021044.3259705.7008520073059739760.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull drm fixes from Daniel Vetter:
"I pinged the usual suspects, only intel fixes pending"
* tag 'drm-fixes-2021-04-16' of git://anongit.freedesktop.org/drm/drm:
drm/i915/display/vlv_dsi: Do not skip panel_pwr_cycle_delay when disabling the panel
drm/i915: Don't zero out the Y plane's watermarks
drm/i915/dpcd_bl: Don't try vesa interface unless specified by VBT
|
|
The "Register Offset Low" register of a "DVSEC Register Locator"
contains the 64K aligned offset for the registers along with the BAR
indicator and an id. The implementation was treating the "Register Block
Offset Low" field a value rather than as a pre-aligned component of the
64-bit offset. So, just mask, don't mask and shift (FIELD_GET).
The user visible result of this bug is that the driver fails to bind to
the device after none of the required blocks are found.
This was missed earlier because the primary development done in the QEMU
environment only uses 0 offsets, i.e. 0 shifted is still 0.
Fixes: 8adaf747c9f0 ("cxl/mem: Find device capabilities")
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210415232610.603273-1-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
snd_una update should not be done when the same skb is being
sent out.chcr_short_record_handler() sends it again even
though SND_UNA update is already sent for the skb in
chcr_ktls_xmit(), which causes mismatch in un-acked
TCP seq number, later causes problem in sending out
complete record.
Fixes: 429765a149f1 ("chcr: handle partial end part of a record")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW doesn't need marking TCB closed. This TCB state change
sometimes causes problem to the new connection which gets
the same tid.
Fixes: 34aba2c45024 ("cxgb4/chcr : Register to tls add and del callback")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sge queue is full and chcr_ktls_xmit_wr_complete()
returns failure, skb is not freed if it is not the last tls record in
this skb, causes refcount never gets freed and tls_dev_del()
never gets called on this connection.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking page refcount is not ideal and causes kernel panic
sometimes. It's better to take tx_ctx lock for the complete
skb transmit, to avoid page cleanup if ACK received in middle.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-04-14
This series provides 3 small fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e]
Call Trace:
[2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e]
[2160294.717666] dev_xdp_install+0x4f/0x70
[2160294.718036] dev_change_xdp_fd+0x11f/0x230
[2160294.718380] ? dev_disable_lro+0xe0/0xe0
[2160294.718705] do_setlink+0xac7/0xe70
[2160294.719035] ? __nla_parse+0xed/0x120
[2160294.719365] rtnl_newlink+0x73b/0x860
Fixes: 41c445ff0f48 ("i40e: main driver core")
Co-developed-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Jason Xing <xingwanli@kuaishou.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
"A single fix for an older problem with the sysfs interface: do not
allow exporting GPIO lines which were marked invalid by the driver"
* tag 'gpio-fixes-for-v5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sysfs: Obey valid_mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
"The changes are all device/driver specific fixes:
- EV_KEY and EV_ABS regression fix for Wacom from Ping Cheng
- BIOS-specific quirk to fix some of the AMD_SFH-based systems, from
Hans de Goede
- other small error handling fixes and device ID additions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: wacom: set EV_KEY and EV_ABS only for non-HID_GENERIC type of devices
AMD_SFH: Add DMI quirk table for BIOS-es which don't set the activestatus bits
AMD_SFH: Add sensor_mask module parameter
AMD_SFH: Removed unused activecontrolstatus member from the amd_mp2_dev struct
HID: wacom: Assign boolean values to a bool variable
HID cp2112: fix support for multiple gpiochips
HID: alps: fix error return code in alps_input_configured()
HID: asus: Add support for 2021 ASUS N-Key keyboard
HID: google: add don USB id
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a few driver fixes here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - drop zero-checking of ABS_MT_TOUCH_MAJOR resolution
Input: elants_i2c - fix division by zero if firmware reports zero phys size
Input: nspire-keypad - enable interrupts only when opened
Input: i8042 - fix Pegatron C15B ID entry
Input: n64joy - fix return value check in n64joy_probe()
Input: s6sy761 - fix coordinate read bit shift
|
|
In the nft_offload there is the mate flow_dissector with no
ingress_ifindex but with ingress_iftype that only be used
in the software. So if the mask of ingress_ifindex in meta is
0, this meta check should be bypass.
Fixes: 6d65bc64e232 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Change register setting from bit number to bit mask.
Fixes: b5ede32d3329 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prevent setting of devlink traps on the uplink while in switchdev mode.
In this mode, it is the SW switch responsibility to handle both packets
with a mismatch in destination MAC or VLAN ID. Therefore, there are no
flow steering tables to trap undesirable packets and driver crashes upon
setting a trap.
Fixes: 241dc159391f ("net/mlx5: Notify on trap action by blocking event")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-14
This series contains updates to ixgbe and ice drivers.
Alex Duyck fixes a NULL pointer dereference for ixgbe.
Yongxin Liu fixes an unbalanced enable/disable which was causing a call
trace with suspend for ixgbe.
Colin King fixes a potential infinite loop for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which
introduces a suspend/resume regression on Jetson TX2 boards that can be
reproduced every time. Given that the issue that this was supposed to
fix only occurs very sporadically the safest course of action is to
revert before v5.12 and then we can have another go at fixing the more
rare issue in the next release (and perhaps backport it if necessary).
The root cause of the observed problem seems to be that when the system
is suspended, some packets are still in transit. When the descriptors
for these buffers are cleared on resume, the descriptors become invalid
and cause a fatal bus error.
Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28:
duplicated argument to & or |
The CN6XXX_INTR_M1UPB0_ERR here is duplicate.
Here should be CN6XXX_INTR_M1UNB0_ERR.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM verity target FEC support's RS roots IO to always be aligned.
This fixes a previous stable@ fix that overcorrected for a different
configuration that also resulted in misaligned roots IO"
* tag 'for-5.12/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity fec: fix misaligned RS roots IO
|
|
This is a leftover of the below commit.
Fixes: 4f04256c983a ("net: vrf: Drop local rtable and rt6_info")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since
interrupt_rx() calls napi_schedule_prep/__napi_schedule during every
receive interrupt.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(),
which will calls napi_schedule if previous state is VNIC_CLOSED
(i.e, the reset case, and "ifconfig down" case). So there is no need
for do_reset to call napi_schedule again at the end of the function
though napi_schedule will neglect the request if napi is already
scheduled.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__ibmvnic_open calls napi_disable without checking whether NAPI polling
has already been disabled or not. This could cause napi_disable
being called twice, which could generate deadlock. For example,
the first napi_disable will spin until NAPI_STATE_SCHED is cleared
by napi_complete_done, then set it again.
When napi_disable is called the second time, it will loop infinitely
because no dev->poll will be running to clear NAPI_STATE_SCHED.
To prevent above scenario from happening, call ibmvnic_napi_disable()
which checks if napi is disabled or not before calling napi_disable.
Fixes: bfc32f297337 ("ibmvnic: Move resource initialization to its own routine")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=212617
Fixes: 9cf9b84cc701 ("r8169: make use of phy_set_asym_pause")
Reported-by: Roman Mamedov <rm+bko@romanrm.net>
Tested-by: Roman Mamedov <rm+bko@romanrm.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to
block size") introduced the possibility for misaligned roots IO
relative to the underlying device's logical block size. E.g. Android's
default RS roots=2 results in dm_bufio->block_size=1024, which causes
the following EIO if the logical block size of the device is 4096,
given v->data_dev_block_bits=12:
E sd 0 : 0:0:0: [sda] tag#30 request not aligned to the logical block size
E blk_update_request: I/O error, dev sda, sector 10368424 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
E device-mapper: verity-fec: 254:8: FEC 9244672: parity read failed (block 18056): -5
Fix this by onlu using f->roots for dm_bufio blocksize IFF it is
aligned to v->data_dev_block_bits.
Fixes: df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to block size")
Cc: stable@vger.kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A couple of dmaengine driver fixes for:
- race and descriptor issue for xilinx driver
- fix interrupt handling, wq state & cleanup, field sizes for
completion, msix permissions for idxd driver
- runtime pm fix for tegra driver
- double free fix in dma_async_device_register"
* tag 'dmaengine-fix-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: idxd: fix wq cleanup of WQCFG registers
dmaengine: idxd: clear MSIX permission entry on shutdown
dmaengine: plx_dma: add a missing put_device() on error path
dmaengine: tegra20: Fix runtime PM imbalance on error
dmaengine: Fix a double free in dma_async_device_register
dmaengine: dw: Make it dependent to HAS_IOMEM
dmaengine: idxd: fix wq size store permission state
dmaengine: idxd: fix opcap sysfs attribute output
dmaengine: idxd: fix delta_rec and crc size field for completion record
dmaengine: idxd: Fix clobbering of SWERR overflow bit on writeback
dmaengine: xilinx: dpdma: Fix race condition in done IRQ
dmaengine: xilinx: dpdma: Fix descriptor issuing on video group
|
|
Pull VFIO fix from Alex Williamson:
"Verify mmap region within range (Christian A. Ehrhardt)"
* tag 'vfio-v5.12-rc8' of git://github.com/awilliam/linux-vfio:
vfio/pci: Add missing range check in vfio_pci_mmap
|
|
The logic in connect() is currently written with the assumption that
xenbus_watch_pathfmt() will return an error for a node that does not
exist. This assumption is incorrect: xenstore does allow a watch to
be registered for a nonexistent node (and will send notifications
should the node be subsequently created).
As of commit 1f2565780 ("xen-netback: remove 'hotplug-status' once it
has served its purpose"), this leads to a failure when a domU
transitions into XenbusStateConnected more than once. On the first
domU transition into Connected state, the "hotplug-status" node will
be deleted by the hotplug_status_changed() callback in dom0. On the
second or subsequent domU transition into Connected state, the
hotplug_status_changed() callback will therefore never be invoked, and
so the backend will remain stuck in InitWait.
This failure prevents scenarios such as reloading the xen-netfront
module within a domU, or booting a domU via iPXE. There is
unfortunately no way for the domU to work around this dom0 bug.
Fix by explicitly checking for existence of the "hotplug-status" node,
thereby creating the behaviour that was previously assumed to exist.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is more correct to use dev_kfree_skb_irq when packets are dropped,
and to use dev_consume_skb_irq when packets are consumed.
Fixes: 0d973388185d ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"Fix WAITRDY break condition and timeout in mtk nand driver"
* tag 'fixes-for-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: mtk: Fix WAITRDY break condition and timeout
|
|
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864d9 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
pci_disable_device() called in __ixgbe_shutdown() decreases
dev->enable_cnt by 1. pci_enable_device_mem() which increases
dev->enable_cnt by 1, was removed from ixgbe_resume() in commit
6f82b2558735 ("ixgbe: use generic power management"). This caused
unbalanced increase/decrease. So add pci_enable_device_mem() back.
Fix the following call trace.
ixgbe 0000:17:00.1: disabling already-disabled device
Call Trace:
__ixgbe_shutdown+0x10a/0x1e0 [ixgbe]
ixgbe_suspend+0x32/0x70 [ixgbe]
pci_pm_suspend+0x87/0x160
? pci_pm_freeze+0xd0/0xd0
dpm_run_callback+0x42/0x170
__device_suspend+0x114/0x460
async_suspend+0x1f/0xa0
async_run_entry_fn+0x3c/0xf0
process_one_work+0x1dd/0x410
worker_thread+0x34/0x3f0
? cancel_delayed_work+0x90/0x90
kthread+0x14c/0x170
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
Fixes: 6f82b2558735 ("ixgbe: use generic power management")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ixgbe driver currently generates a NULL pointer dereference when
performing the ethtool loopback test. This is due to the fact that there
isn't a q_vector associated with the test ring when it is setup as
interrupts are not normally added to the test rings.
To address this I have added code that will check for a q_vector before
returning a napi_id value. If a q_vector is not present it will return a
value of 0.
Fixes: b02e5a0ebb17 ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When mmaping an extra device region verify that the region index
derived from the mmap offset is valid.
Fixes: a15b1883fee1 ("vfio_pci: Allow mapping extra regions")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Message-Id: <20210412214124.GA241759@lisa.in-ulm.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A pre-release silicon erratum workaround where wq reset does not clear
WQCFG registers was leaked into upstream code. Use wq reset command
instead of blasting the MMIO region. This also address an issue where
we clobber registers in future devices.
Fixes: da32b28c95a7 ("dmaengine: idxd: cleanup workqueue config after disabling")
Reported-by: Shreenivaas Devarajan <shreenivaas.devarajan@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161824330020.881560.16375921906426627033.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add disabling/clearing of MSIX permission entries on device shutdown to
mirror the enabling of the MSIX entries on probe. Current code left the
MSIX enabled and the pasid entries still programmed at device shutdown.
Fixes: 8e50d392652f ("dmaengine: idxd: Add shared workqueue support")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161824457969.882533.6020239898682672311.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
the panel
After the recently added commit fe0f1e3bfdfe ("drm/i915: Shut down
displays gracefully on reboot"), the DSI panel on a Cherry Trail based
Predia Basic tablet would no longer properly light up after reboot.
I've managed to reproduce this without rebooting by doing:
chvt 3; echo 1 > /sys/class/graphics/fb0/blank;\
echo 0 > /sys/class/graphics/fb0/blank
Which rapidly turns the panel off and back on again.
The vlv_dsi.c code uses an intel_dsi_msleep() helper for the various delays
used for panel on/off, since starting with MIPI-sequences version >= 3 the
delays are already included inside the MIPI-sequences.
The problems exposed by the "Shut down displays gracefully on reboot"
change, show that using this helper for the panel_pwr_cycle_delay is
not the right thing to do. This has not been noticed until now because
normally the panel never is cycled off and directly on again in quick
succession.
Change the msleep for the panel_pwr_cycle_delay to a normal msleep()
call to avoid the panel staying black after a quick off + on cycle.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: fe0f1e3bfdfe ("drm/i915: Shut down displays gracefully on reboot")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210325114823.44922-1-hdegoede@redhat.com
(cherry picked from commit 2878b29fc25a0dac0e1c6c94177f07c7f94240f0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Don't zero out the watermarks for the Y plane since we've already
computed them when computing the UV plane's watermarks (since the
UV plane always appears before ethe Y plane when iterating through
the planes).
This leads to allocating no DDB for the Y plane since .min_ddb_alloc
also gets zeroed. And that of course leads to underruns when scanning
out planar formats.
Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: dbf71381d733 ("drm/i915: Nuke intel_atomic_crtc_state_for_each_plane_state() from skl+ wm code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210327005945.4929-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit f99b805fb9413ff007ca0b6add871737664117dd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Looks like that there actually are another subset of laptops on the market
that don't support the Intel HDR backlight interface, but do advertise
support for the VESA DPCD backlight interface despite the fact it doesn't
seem to work.
Note though I'm not entirely clear on this - on one of the machines where
this issue was observed, I also noticed that we appeared to be rejecting
the VBT defined backlight frequency in
intel_dp_aux_vesa_calc_max_backlight(). It's noted in this function that:
/* Use highest possible value of Pn for more granularity of brightness
* adjustment while satifying the conditions below.
* ...
* - FxP is within 25% of desired value.
* Note: 25% is arbitrary value and may need some tweak.
*/
So it's possible that this value might just need to be tweaked, but for now
let's just disable the VESA backlight interface unless it's specified in
the VBT just to be safe. We might be able to try enabling this again by
default in the future.
Fixes: 2227816e647a ("drm/i915/dp: Allow forcing specific interfaces through enable_dpcd_backlight")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/3169
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318170204.513000-1-lyude@redhat.com
(cherry picked from commit 9e2eb6d5380e9dadcd2baecb51f238e5eba94bee)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add a missing put_device(&pdev->dev) if the call to
dma_async_device_register(dma); fails.
Fixes: 905ca51e63be ("dmaengine: plx-dma: Introduce PLX DMA engine PCI driver skeleton")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/YFnq/0IQzixtAbC1@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210409082805.23643-1-dinghao.liu@zju.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In the first list_for_each_entry() macro of dma_async_device_register,
it gets the chan from list and calls __dma_async_device_channel_register
(..,chan). We can see that chan->local is allocated by alloc_percpu() and
it is freed chan->local by free_percpu(chan->local) when
__dma_async_device_channel_register() failed.
But after __dma_async_device_channel_register() failed, the caller will
goto err_out and freed the chan->local in the second time by free_percpu().
The cause of this problem is forget to set chan->local to NULL when
chan->local was freed in __dma_async_device_channel_register(). My
patch sets chan->local to NULL when the callee failed to avoid double free.
Fixes: d2fb0a0438384 ("dmaengine: break out channel registration")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20210331014458.3944-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some architectures do not provide devm_*() APIs. Hence make the driver
dependent on HAVE_IOMEM.
Fixes: dbde5c2934d1 ("dw_dmac: use devm_* functions to simplify code")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210324141757.24710-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
WQ size can only be changed when the device is disabled. Current code
allows change when device is enabled but wq is disabled. Change the check
to detect device state.
Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161782558755.107710.18138252584838406025.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The operation capability register is 256bits. The current output only
prints out the first 64bits. Fix to output the entire 256bits. The current
code omits operation caps from IAX devices.
Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Reported-by: Lucas Van <lucas.van@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161645624963.2003736.829798666998490151.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
Linus Torvalds
Dan Williams
Ben Widawsky
Vinay Kumar Yadav
David S. Miller
Jason Xing
wenxu
Aya Levin
Thierry Reding
Wan Jiabing
Claudiu Beznea
Nicolas Dichtel
Lijun Pan
Heiner Kallweit
Jaegeuk Kim
Michael Brown
Colin Ian King
Yongxin Liu
Alexander Duyck
Christian A. Ehrhardt
Pali Rohár
Dave Jiang
Hans de Goede
Ville Syrjälä
Lyude Paul
Dan Carpenter
Dinghao Liu
Lv Yunlong
Andy Shevchenko