| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit cdf10ffe8f626d8a2edc354abf063df0078b2d71 ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c09795 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88b20f84f0fe47409342669caf3e58a3fc64c316 ]
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d54e ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f4e56ec4452f48b8292dcf0e1c4bdac83506fb8b ]
The error flow fixed in this patch is not possible because all kernel
users of create QP interface check that device supports steering before
set IB_QP_CREATE_NETIF_QP flag.
Fixes: c1c98501121e ("IB/mlx4: Add support for steerable IB UD QPs")
Link: https://lore.kernel.org/r/91c61f6e60eb0240f8bbc321fda7a1d2986dd03c.1634023677.git.leonro@nvidia.com
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f4875d509a0a78ad294a1a538d534b5ba94e685a ]
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili
Fixes: 5036f0a0ecd3 ("[SCSI] csiostor: Fix sparse warnings.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf895295e9a73411889816f1a0c1f4f1a2d9c678 ]
Currently the rt5033_battery driver provides voltage values in mV. It
should be µV as stated in Documentation/power/power_supply_class.rst.
Fixes: b847dd96e659 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68e7c510fdf4f6167404609da52e1979165649f6 ]
Return an error code if usb_get_function() fails. Don't return success.
Fixes: 4bc8a33f2407 ("usb: gadget: hid: convert to new interface of f_hid")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123739.GC15188@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebabb77a2a115b6c5e68f7364b598310b5f61fb2 ]
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.
Instead of adding ifdeffery here and there, drop ACPI_PTR().
Fixes: 6a7320c4669f ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f2719b26ae27282c145202ffd656d5ff1fe737cc ]
While investigating a lockup at startup on Powerbook 3400C, it was
identified that the fbdev driver generates alignment exception at
startup:
--- interrupt: 600 at memset+0x60/0xc0
NIP: c0021414 LR: c03fc49c CTR: 00007fff
REGS: ca021c10 TRAP: 0600 Tainted: G W (5.14.2-pmac-00727-g12a41fa69492)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44008442 XER: 20000100
DAR: cab80020 DSISR: 00017c07
GPR00: 00000007 ca021cd0 c14412e0 cab80000 00000000 00100000 cab8001c 00000004
GPR08: 00100000 00007fff 00000000 00000000 84008442 00000000 c0006fb4 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
GPR24: 00000000 81800000 00000320 c15fa400 c14d1878 00000000 c14d1800 c094e19c
NIP [c0021414] memset+0x60/0xc0
LR [c03fc49c] chipsfb_pci_init+0x160/0x580
--- interrupt: 600
[ca021cd0] [c03fc46c] chipsfb_pci_init+0x130/0x580 (unreliable)
[ca021d20] [c03a3a70] pci_device_probe+0xf8/0x1b8
[ca021d50] [c043d584] really_probe.part.0+0xac/0x388
[ca021d70] [c043d914] __driver_probe_device+0xb4/0x170
[ca021d90] [c043da18] driver_probe_device+0x48/0x144
[ca021dc0] [c043e318] __driver_attach+0x11c/0x1c4
[ca021de0] [c043ad30] bus_for_each_dev+0x88/0xf0
[ca021e10] [c043c724] bus_add_driver+0x190/0x22c
[ca021e40] [c043ee94] driver_register+0x9c/0x170
[ca021e60] [c0006c28] do_one_initcall+0x54/0x1ec
[ca021ed0] [c08246e4] kernel_init_freeable+0x1c0/0x270
[ca021f10] [c0006fdc] kernel_init+0x28/0x11c
[ca021f30] [c0017148] ret_from_kernel_thread+0x14/0x1c
Instruction dump:
7d4601a4 39490777 7d4701a4 39490888 7d4801a4 39490999 7d4901a4 39290aaa
7d2a01a4 4c00012c 4bfffe88 0fe00000 <4bfffe80> 9421fff0 38210010 48001970
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Fixes: 8c8709334cec ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK")
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/884a54f1e5cb774c1d9b4db780209bee5d4f6718.1631712563.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ed2f3545c2e5acfbccd7f85fea5b1a82e9862d7 ]
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fbdd ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 986b5094708e508baa452a23ffe809870934a7df ]
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
Fixes: a38045121bf4 ("soc/tegra: pmc: Add generic PM domain support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbd9a3347c757383f3d2b50cf7cfd03eb479c481 ]
dc395x_init_one()->adapter_init() might fail. In this case, the acb is
already cleaned up by adapter_init(), no need to do that in
adapter_uninit(acb) again.
[ 1.252251] dc395x: adapter init failed
[ 1.254900] RIP: 0010:adapter_uninit+0x94/0x170 [dc395x]
[ 1.260307] Call Trace:
[ 1.260442] dc395x_init_one.cold+0x72a/0x9bb [dc395x]
Link: https://lore.kernel.org/r/20210907040702.1846409-1-ztong0001@gmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2aa717473ce96c93ae43a5dc8c23cedc8ce7dd9f ]
The s3c24xx_init_intc() returns an error pointer upon failure, not NULL.
let's add an error pointer check in s3c24xx_handle_irq.
s3c_intc[0] is not NULL or ERR, we can simplify the code.
Fixes: 1f629b7a3ced ("ARM: S3C24XX: transform irq handling into a declarative form")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Link: https://lore.kernel.org/r/20210901123557.1043953-1-liu.yun@linux.dev
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dcd3f985b20ffcc375f82ca0ca9f241c7025eb5e ]
The port->attr.port_cap_flags should be set to enum
ib_port_capability_mask_bits in ib_mad.h, not
RDMA_CORE_CAP_PROT_ROCE_UDP_ENCAP.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20210831083223.65797-1-weijunji@bytedance.com
Signed-off-by: Junji Wei <weijunji@bytedance.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e20d00158f31f7631d68b86996b7e951c4451c8 ]
Soon after registering a CRQ it is possible that we get a fail over or
maybe a CRQ_INIT from the VIOS while interrupts were disabled.
Look for any such CRQs after enabling interrupts.
Otherwise we can intermittently fail to bring up ibmvnic adapters during
boot, specially in kexec/kdump kernels.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd8d9731bcdfb22d28e45bce789bcb211c868c78 ]
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit daf182d360e509a494db18666799f4e85d83dda0 ]
For each rate change command submission, the FW has to do a phy
power off sequence internally. For this to happen correctly, the
PLL re-initialization control setting has to be turned off before
sending mailbox commands and re-enabled once the command submission
is complete.
Without the PLL control setting, the link up takes longer time in a
fixed phy configuration.
Fixes: 47f164deab22 ("amd-xgbe: Add PCI device support")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9692151e2fe7a326bafe99836fd1f20a2cc3a049 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff88812c7d7400 (size 512):
comm "kworker/6:1", pid 176, jiffies 4295003332 (age 822.830s)
hex dump (first 32 bytes):
00 68 1e 04 81 88 ff ff 01 00 00 00 00 00 00 00 .h..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8167939c>] slab_post_alloc_hook+0x9c/0x490
[<ffffffff8167f627>] kmem_cache_alloc_trace+0x1f7/0x470
[<ffffffffa02c9873>] if_usb_probe+0x63/0x446 [usb8xxx]
[<ffffffffa022668a>] usb_probe_interface+0x1aa/0x3c0 [usbcore]
[<ffffffff82b59630>] really_probe+0x190/0x480
[<ffffffff82b59a19>] __driver_probe_device+0xf9/0x180
[<ffffffff82b59af3>] driver_probe_device+0x53/0x130
[<ffffffff82b5a075>] __device_attach_driver+0x105/0x130
[<ffffffff82b55949>] bus_for_each_drv+0x129/0x190
[<ffffffff82b593c9>] __device_attach+0x1c9/0x270
[<ffffffff82b5a250>] device_initial_probe+0x20/0x30
[<ffffffff82b579c2>] bus_probe_device+0x142/0x160
[<ffffffff82b52e49>] device_add+0x829/0x1300
[<ffffffffa02229b1>] usb_set_configuration+0xb01/0xcc0 [usbcore]
[<ffffffffa0235c4e>] usb_generic_driver_probe+0x6e/0x90 [usbcore]
[<ffffffffa022641f>] usb_probe_device+0x6f/0x130 [usbcore]
cardp is missing being freed in the error handling path of the probe
and the path of the disconnect, which will cause memory leak.
This patch adds the missing kfree().
Fixes: 876c9d3aeb98 ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211020120345.2016045-3-wanghai38@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d549107305b4634c81223a853701c06bcf657bc3 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff88810a2ddc00 (size 512):
comm "kworker/6:1", pid 176, jiffies 4295009893 (age 757.220s)
hex dump (first 32 bytes):
00 50 05 18 81 88 ff ff 00 00 00 00 00 00 00 00 .P..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8167939c>] slab_post_alloc_hook+0x9c/0x490
[<ffffffff8167f627>] kmem_cache_alloc_trace+0x1f7/0x470
[<ffffffffa02a1530>] if_usb_probe+0x60/0x37c [libertas_tf_usb]
[<ffffffffa022668a>] usb_probe_interface+0x1aa/0x3c0 [usbcore]
[<ffffffff82b59630>] really_probe+0x190/0x480
[<ffffffff82b59a19>] __driver_probe_device+0xf9/0x180
[<ffffffff82b59af3>] driver_probe_device+0x53/0x130
[<ffffffff82b5a075>] __device_attach_driver+0x105/0x130
[<ffffffff82b55949>] bus_for_each_drv+0x129/0x190
[<ffffffff82b593c9>] __device_attach+0x1c9/0x270
[<ffffffff82b5a250>] device_initial_probe+0x20/0x30
[<ffffffff82b579c2>] bus_probe_device+0x142/0x160
[<ffffffff82b52e49>] device_add+0x829/0x1300
[<ffffffffa02229b1>] usb_set_configuration+0xb01/0xcc0 [usbcore]
[<ffffffffa0235c4e>] usb_generic_driver_probe+0x6e/0x90 [usbcore]
[<ffffffffa022641f>] usb_probe_device+0x6f/0x130 [usbcore]
cardp is missing being freed in the error handling path of the probe
and the path of the disconnect, which will cause memory leak.
This patch adds the missing kfree().
Fixes: c305a19a0d0a ("libertas_tf: usb specific functions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211020120345.2016045-2-wanghai38@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c65b52d02f6c1a06ddb20cba175ad49eccd6410d ]
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2baa1de7a ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ]
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc8a8bc37466f79b24d972555237f3d591150602 ]
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd96e35ea7b95f1e216277805be89d66e4ae962d ]
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce754 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1476
Reported-by: Tor Vic <torvic9@mailbox.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce5f6c2c9b0fcb4094f8e162cfd37fb4294204f7 ]
The 'reg_vmmc' regulator is enabled in the probe. It is never disabled.
Neither in the error handling path of the probe nor in the remove
function.
Register a devm_action to disable it when needed.
Fixes: 4dc5a79f1350 ("mmc: mxs-mmc: enable regulator for mmc slot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4aadb3c97835f7b80f00819c3d549e6130384e67.1634365151.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2203bd0e5c12ffc53ffdd4fbd7b12d6ba27e0424 ]
The msm_gem_new_impl() function cleans up after itself so there is no
need to call drm_gem_object_put(). Conceptually, it does not make sense
to call a kref_put() function until after the reference counting has
been initialized which happens immediately after this call in the
drm_gem_(private_)object_init() functions.
In the msm_gem_import() function the "obj" pointer is uninitialized, so
it will lead to a crash.
Fixes: 05b849111c07 ("drm/msm: prime support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211013081315.GG6010@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a491167fe0cf9f26062462de2a8688b96125d48 ]
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9b8 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ada61aa0b1184a8fda1a89a340c7d6cc4e59aee5 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888102740438 (size 8):
comm "27", pid 859, jiffies 4295031351 (age 143.992s)
hex dump (first 8 bytes):
68 77 6d 6f 6e 30 00 00 hwmon0..
backtrace:
[<00000000544b5996>] __kmalloc_track_caller+0x1a6/0x300
[<00000000df0d62b9>] kvasprintf+0xad/0x140
[<00000000d3d2a3da>] kvasprintf_const+0x62/0x190
[<000000005f8f0f29>] kobject_set_name_vargs+0x56/0x140
[<00000000b739e4b9>] dev_set_name+0xb0/0xe0
[<0000000095b69c25>] __hwmon_device_register+0xf19/0x1e50 [hwmon]
[<00000000a7e65b52>] hwmon_device_register_with_info+0xcb/0x110 [hwmon]
[<000000006f181e86>] devm_hwmon_device_register_with_info+0x85/0x100 [hwmon]
[<0000000081bdc567>] tmp421_probe+0x2d2/0x465 [tmp421]
[<00000000502cc3f8>] i2c_device_probe+0x4e1/0xbb0
[<00000000f90bda3b>] really_probe+0x285/0xc30
[<000000007eac7b77>] __driver_probe_device+0x35f/0x4f0
[<000000004953d43d>] driver_probe_device+0x4f/0x140
[<000000002ada2d41>] __device_attach_driver+0x24c/0x330
[<00000000b3977977>] bus_for_each_drv+0x15d/0x1e0
[<000000005bf2a8e3>] __device_attach+0x267/0x410
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: bab2243ce189 ("hwmon: Introduce hwmon_device_register_with_groups")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012112758.2681084-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit beae4a6258e64af609ad5995cc6b6056eb0d898e ]
The "msh" pointer is device managed, meaning that memstick_alloc_host()
calls device_initialize() on it. That means that it can't be free
using kfree() but must instead be freed with memstick_free_host().
Otherwise it leads to a tiny memory leak of device resources.
Fixes: 60fdd931d577 ("memstick: add support for JMicron jmb38x MemoryStick host controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123912.GD15188@kili
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4853396f03c3019eccf5cd113e464231e9ddf0b3 ]
clang-14 complains about a sanity check that always passes when the
page size is 64KB or larger:
drivers/memstick/core/ms_block.c:1739:21: error: result of comparison of constant 65536 with expression of type 'unsigned short' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (msb->page_size > PAGE_SIZE) {
~~~~~~~~~~~~~~ ^ ~~~~~~~~~
This is fine, it will still work on all architectures, so just shut
up that warning with a cast.
Fixes: 0ab30494bc4f ("memstick: add support for legacy memorysticks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927094520.696665-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9b793db5fca44d01f72d3564a168171acf7c4076 ]
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: ef1a628d83fc ("b43: Implement dynamic PHY API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073621.GE8404@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1c8380b0320ab757e60ed90efc8b1992a943256 ]
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073542.GD8404@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6f5f0c8f72d348b2d07b20d7b680ef13a7ffe98 ]
Currently mtk_rng_runtime_suspend/resume is called for both runtime pm
and system sleep operations.
This is wrong as these should only be runtime ops as the name already
suggests. Currently freezing the system will lead to a call to
mtk_rng_runtime_suspend even if the device currently isn't active. This
leads to a clock warning because it is disabled/unprepared although it
isn't enabled/prepared currently.
This patch fixes this by only setting the runtime pm ops and forces to
call the runtime pm ops from the system sleep ops as well if active but
not otherwise.
Fixes: 81d2b34508c6 ("hwrng: mtk - add runtime PM support")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 18fcba469ba5359c1de7e3fb16f7b9e8cd1b8e02 ]
Upon receiving a PFVF message, check if the interrupt bit is set in the
message. If it is not, that means that the interrupt was probably
triggered by a collision. In this case, disregard the message and
re-enable the interrupts.
Fixes: ed8ccaef52fa ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9b768e8a3909ac1ab39ed44a3933716da7761a6f ]
Detect a PFVF collision between the local and the remote function by
checking if the message on the PFVF CSR has been overwritten.
This is done after the remote function confirms that the message has
been received, by clearing the interrupt bit, or the maximum number of
attempts (ADF_IOV_MSG_ACK_MAX_RETRY) to check the CSR has been exceeded.
Fixes: ed8ccaef52fa ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4925642d541278575ad1948c5924d71ffd57ef14 ]
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
1) ath9k_queue_reset()
...
-> ath9k_hw_kill_interrupts()
-> set_bit(ATH_OP_HW_RESET, &common->op_flags);
...
<- returns
2) ath9k_tasklet()
...
-> ath9k_hw_resume_interrupts()
...
<- returns
3) loops around:
...
handle_int()
-> ath_isr()
...
-> if (test_bit(ATH_OP_HW_RESET,
&common->op_flags))
return IRQ_HANDLED;
x) ath_reset_internal():
=> never reached <=
And in ath_isr() we would typically see the following interrupts /
interrupt causes:
* status: 0x00111030 or 0x00110030
* async_cause: 2 (AR_INTR_MAC_IPQ)
* sync_cause: 0
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: 872b5d814f99 ("ath9k: do not access hardware on IRQs during reset")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5f5a66c9aa9c331da5527c2e3fd9394e7091e01 ]
Commit c343bf1ba5ef ("cpuidle: Fix three reference count leaks")
fixes the cleanup of kobjects; however, it removes kfree() calls
altogether, leading to memory leaks.
Fix those and also defer the initialization of dev->kobj_dev until
after the error check, so that we do not end up with a dangling
pointer.
Fixes: c343bf1ba5ef ("cpuidle: Fix three reference count leaks")
Signed-off-by: Anel Orazgaliyeva <anelkz@amazon.de>
Suggested-by: Aman Priyadarshi <apeureka@amazon.de>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7266dda2f1dfe151b12ef0c14eb4d4e622fb211c ]
Currently a call to snd_card_new that fails will set card with a NULL
pointer, this causes a null pointer dereference on the error cleanup
path when card it passed to snd_card_free. Fix this by adding a new
error exit path that does not call snd_card_free and exiting via this
new path.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 9e44d63246a9 ("[media] cx23885: Add ALSA support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2908249f3878a591f7918368fdf0b7b0a6c3158c ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Silicon Labs Si470x FM Radio Re".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 78656acdcf48 ("V4L/DVB (7038): USB radio driver for Silicon Labs Si470x FM Radio Receivers")
Fixes: cc35bbddfe10 ("V4L/DVB (12416): radio-si470x: add i2c driver for si470x")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
'mtk_vpu_probe()'
[ Upstream commit 2143ad413c05c7be24c3a92760e367b7f6aaac92 ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
Update the error handling path accordingly.
Fixes: 3003a180ef6b ("[media] VPU: mediatek: support Mediatek VPU")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit afae4ef7d5ad913cab1316137854a36bea6268a5 ]
Syzbot reported ununit-value bug in az6027_rc_query(). The problem was
in missing state pointer initialization. Since this function does nothing
we can simply initialize state to REMOTE_NO_KEY_PRESSED.
Reported-and-tested-by: syzbot+2cd8c5db4a85f0a04142@syzkaller.appspotmail.com
Fixes: 76f9a820c867 ("V4L/DVB: AZ6027: Initial import of the driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca9b8f56ec089d3a436050afefd17b7237301f47 ]
Fix the missing clk_disable_unprepare() before return
from bcm_qspi_probe() in the error handling case.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211018073413.2029081-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5322b9ab5f63536c41301150b7ce64605ce52cc ]
Just like we have default SMPS mode as dynamic in powersave,
we should not enable RX-diversity in powersave, to reduce
power consumption when connected to a non-MIMO AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.fc896bc5cdaa.I1d11da71b8a5cbe921a37058d5f578f1b14a2023@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 257051a235c17e33782b6e24a4b17f2d7915aaec ]
When the driver fails to request the firmware, it calls its error
handler. In the error handler, the driver detaches device from driver
first before releasing the firmware, which can cause a use-after-free bug.
Fix this by releasing firmware first.
The following log reveals it:
[ 9.007301 ] BUG: KASAN: use-after-free in mwl8k_fw_state_machine+0x320/0xba0
[ 9.010143 ] Workqueue: events request_firmware_work_func
[ 9.010830 ] Call Trace:
[ 9.010830 ] dump_stack_lvl+0xa8/0xd1
[ 9.010830 ] print_address_description+0x87/0x3b0
[ 9.010830 ] kasan_report+0x172/0x1c0
[ 9.010830 ] ? mutex_unlock+0xd/0x10
[ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0
[ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0
[ 9.010830 ] __asan_report_load8_noabort+0x14/0x20
[ 9.010830 ] mwl8k_fw_state_machine+0x320/0xba0
[ 9.010830 ] ? mwl8k_load_firmware+0x5f0/0x5f0
[ 9.010830 ] request_firmware_work_func+0x172/0x250
[ 9.010830 ] ? read_lock_is_recursive+0x20/0x20
[ 9.010830 ] ? process_one_work+0x7a1/0x1100
[ 9.010830 ] ? request_firmware_nowait+0x460/0x460
[ 9.010830 ] ? __this_cpu_preempt_check+0x13/0x20
[ 9.010830 ] process_one_work+0x9bb/0x1100
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634356979-6211-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 738216c1953e802aa9f930c5d15b8f9092c847ff ]
In r592_remove(), the driver will free dma after freeing the host, which
may cause a UAF bug.
The following log reveals it:
[ 45.361796 ] BUG: KASAN: use-after-free in r592_remove+0x269/0x350 [r592]
[ 45.364286 ] Call Trace:
[ 45.364472 ] dump_stack_lvl+0xa8/0xd1
[ 45.364751 ] print_address_description+0x87/0x3b0
[ 45.365137 ] kasan_report+0x172/0x1c0
[ 45.365415 ] ? r592_remove+0x269/0x350 [r592]
[ 45.365834 ] ? r592_remove+0x269/0x350 [r592]
[ 45.366168 ] __asan_report_load8_noabort+0x14/0x20
[ 45.366531 ] r592_remove+0x269/0x350 [r592]
[ 45.378785 ]
[ 45.378903 ] Allocated by task 4674:
[ 45.379162 ] ____kasan_kmalloc+0xb5/0xe0
[ 45.379455 ] __kasan_kmalloc+0x9/0x10
[ 45.379730 ] __kmalloc+0x150/0x280
[ 45.379984 ] memstick_alloc_host+0x2a/0x190
[ 45.380664 ]
[ 45.380781 ] Freed by task 5509:
[ 45.381014 ] kasan_set_track+0x3d/0x70
[ 45.381293 ] kasan_set_free_info+0x23/0x40
[ 45.381635 ] ____kasan_slab_free+0x10b/0x140
[ 45.381950 ] __kasan_slab_free+0x11/0x20
[ 45.382241 ] slab_free_freelist_hook+0x81/0x150
[ 45.382575 ] kfree+0x13e/0x290
[ 45.382805 ] memstick_free+0x1c/0x20
[ 45.383070 ] device_release+0x9c/0x1d0
[ 45.383349 ] kobject_put+0x2ef/0x4c0
[ 45.383616 ] put_device+0x1f/0x30
[ 45.383865 ] memstick_free_host+0x24/0x30
[ 45.384162 ] r592_remove+0x242/0x350 [r592]
[ 45.384473 ] pci_device_remove+0xa9/0x250
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/1634383581-11055-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2835f327bd1240508db2c89fe94a056faa53c49a ]
Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
channel_detector_create()
[ Upstream commit 4b6012a7830b813799a7faf40daa02a837e0fd5b ]
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 899a61a3305d49e8a712e9ab20d0db94bde5929f ]
In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d3c4b6f64ad356c0d9ddbcf73fa471e6a841cc5c ]
ACPICA commit 0762982923f95eb652cf7ded27356b247c9774de
During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.
Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271
Reported-by: Reik Keutterling <spielkind@gmail.com>
Tested-by: Reik Keutterling <spielkind@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 476db72e521983ecb847e4013b263072bb1110fc ]
Syzkaller reported a warning called "rcu detected stall in dummy_timer".
The error seems to be an error in mceusb_dev_recv(). In the case of
-EPROTO error, the routine immediately resubmits the URB. Instead it
should return without resubmitting URB.
Reported-by: syzbot+4d3749e9612c2cfab956@syzkaller.appspotmail.com
Signed-off-by: Rajat Asthana <rajatasthana4@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cdfaf4752e6915a4b455ad4400133e540e4dc965 ]
If of_device_get_match_data() return NULL,
then null pointer dereference occurs in s5p_mfc_init_pm().
The patch adds checking if dev->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8515965e5e33f4feb56134348c95953f3eadfb26 ]
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Hans de Goede
Anssi Hannula
Leon Romanovsky
Dan Carpenter
Jakob Hauser
Andy Shevchenko
Christophe Leroy
Dongliang Mu
Christophe JAILLET
Tong Zhang
Jackie Liu
Junji Wei
Sukadev Bhattiprolu
Russell King (Oracle)
Shyam Sundar S K
Wang Hai
Mark Rutland
Stefan Agner
Jonas Dreßler
Nathan Chancellor
Sven Eckelmann
Yang Yingliang
Arnd Bergmann
Markus Schneider-Pargmann
Giovanni Cabiddu
Linus Lüssing
Anel Orazgaliyeva
Colin Ian King
Kees Cook
Pavel Skripkin
Johannes Berg
Zheyu Ma
André Almeida
Tuo Li
Anant Thazhemadam
Rafael J. Wysocki
Rajat Asthana
Nadezda Lutovinova