| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 9827f26374fb85e1811f2adbcc25c8a3992dbe7f.
On 10/09/2018 02:20 AM, Shawn Guo wrote:
> Well, it means the change breaks the ABI between kernel and device tree,
> e.g. the new kernel will not work with existing/installed DTBs.
Revert the change until DTB compatibility issue is resolved.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
The SSD130x OLED display reset signal is active low. Now the reset
sequence is implemented in such a way that users are forced to
define reset-gpios as GPIO_ACTIVE_HIGH in DT to make the reset work.
Do not hard code the active-low sequence into the driver but instead
allow the user to specify the gpio as GPIO_ACTIVE_LOW to reflect
the real world.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
The reset signal can be produced by GPIO expander that can sleep.
In that case the probe function fails. Allow using GPIO expanders for
the reset signal by using the non-atomic gpiod_set_value_cansleep()
function.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bastian Stender <bst@pengutronix.de>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
SSD1306 needs VBAT when it is wired in charge pump configuration only.
Other controllers of the SSD1307 family do not need it at all. This was
introduced by commit ba14301e0356 ("fbdev/ssd1307fb: add support to
enable VBAT").
Without VBAT configuration the driver now fails with:
failed to get VBAT regulator: -19
This is caused by misinterpretation of devm_regulator_get_optional
which "returns a struct regulator corresponding to the regulator
producer or IS_ERR() condition".
Handle -ENODEV without bailing out and making VBAT support really
optional.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
[b.zolnierkie: minor fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Changing this driver to the gpiod API requires the use of the
new-style header, depending on the configuration:
drivers/video/fbdev/ssd1307fb.c: In function 'ssd1307fb_probe':
drivers/video/fbdev/ssd1307fb.c:569:15: error: implicit declaration of function 'devm_gpiod_get_optional';did you mean 'devm_regulator_get_optional'? [-Werror=implicit-function-declaration]
drivers/video/fbdev/ssd1307fb.c:570:11: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
Fixes: 72db33355c14 ("fbdev: ssd1307fb: Start to use gpiod API for reset gpio")
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
SSD1306 does not clear the panel's framebuffer automatically, even if a
HW reset happens, so we need to do that at probe time before enabling
the panel.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
SSD1306 needs VBAT when it is wired in charge pump configuration. This
patch adds support to the driver to enable VBAT regulator at init time.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Make reset gpio devicetree property optional. Depending on the board
designing there may not be a dedicated gpio for resetting the
display. Without a proper reset there may be some junk in the display
memory at probe time, so in such a case the display memory is cleared
before turning it on. The devicetree binding document is also updated.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Start to use gpiod API for reset gpio.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
of_match_device return const data, so instead of casting its return value
this patch constify the device_info pointer.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change in the fb_fix_screeninfo case is
as follows (http://coccinelle.lip6.fr/). The fb_var_screeninfo case is
analogous.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct fb_fix_screeninfo i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct fb_fix_screeninfo e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct fb_fix_screeninfo i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Make sure bit 4 is set for the charge pump setting. It is required according
to SSD1306 App Note.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The ssd1307fb driver supports a lot of chips from the ssd130xfb series.
This patch adds the ssd1309 chip, a 128x64 OLED driver chip. It is very
similar to the other chips and only has some definitions added to
support it.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch sorts the headers on ssd1307fb driver.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Propagate error code on failure. Also changed %ld to %d in dev_err to use
ret variable rather than putting two calls to PTR_ERR.
A simplified version of the semantic match that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The logical not needs to be done after the bit masking.
Fixes: a3998fe03e87 ("fbdev: ssd1307fb: Unify init code and obtain
hw specific bits from DT")
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The error handling got shifted down a few lines from where it was
supposed to be for some reason.
Fixes: a14a7ba8cb0f ('fbdev: ssd1307fb: add backlight controls for setting the contrast')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds ssd1307fb_blank() to make the framebuffer capable
of blanking.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The backlight class is used to create userspace handles for
setting the OLED contrast.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch turns off the display when the driver is unloaded.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds the module parameter "refreshrate" to set delay for the
deferred io. The refresh rate is given in units of Hertz. The default
refresh rate is 1 Hz. The refresh rate set through the newly introduced
parameter applies to all instances of the driver and for now it is not
possible to change it individually.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds support for the SSD1305 OLED controller.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The 130X controllers are very similar from the configuration point of view.
The configuration registers for the SSD1305/6/7 are bit identical (except the
the VHCOM register and the the default values for clock setup register). This
patch unifies the init code of the controller and adds hardware specific
properties to DT that are needed to correctly initialize the device.
The SSD130X can be wired to the OLED panel in various ways. Even for the
same controller this wiring can differ from one display module to another
and can not be probed by software. The added DT properties reflect these
hardware decisions of the display module manufacturer.
The 'com-sequential', 'com-lrremap' and 'com-invdir' values define different
possibilities for the COM signals pin configuration and readout direction
of the video memory. The 'segment-no-remap' allows the inversion of the
memory-to-pin mapping ultimately inverting the order of the controllers
output pins. The 'prechargepX' values need to be adapted according to the
capacitance of the OLEDs pixel cells.
So far these hardware specific bits are hard coded in the init code, making
the driver usable only for one certain wiring of the controller. This patch
makes the driver usable with all possible hardware setups, given a valid hw
description in DT. If these values are not set in DT the default values,
as they are set in the ssd1307 init code right now, are used. This implies
that without the corresponding DT property "segment-no-remap" the segment
remap of the ssd130X controller gets activated. Even though this is not the
default behaviour according to the datasheet it maintains backward
compatibility with older DTBs.
Note that the SSD1306 does not seem to be using the configuration written to
the registers at all. Therefore this patch does not try to maintain these
values without changes in DT. For reference an example is added to the DT
bindings documentation that reproduces the configuration that is set in the
current init code.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Tested-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Currently the videomemory is allocated by kmalloc, making it a memory
region that is not necessarily page aligend. This leads to problems
upon mmap call, where the video memory's address gets aligned to the
next page boundary. The result is that the userspace program that issued
the mmap call is not able to access the video memory from the start to
the next page boundary.
This patch changes the allocation of the video memory to use
__get_free_pages() in order to obtain memory that is aligned
to page boundaries.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
the smem_start pointer of the framebuffer info struct needs to hold the
physical address rather than the logical address. Right now the logical
address returned by kmalloc is stored. This patch converts this address
to a physical address and thus fixes a driver crash on mmaping the
framebuffer memory due to an access to the wrong memory address.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
this patch fixes ssd1307fb_ssd1306_init() function to return
proper error codes in case of failures.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
this patch sets the default height if its not found in DT.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
this patch drops the unused function ssd1307fb_write_data().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.
Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.
No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
Bartlomiej Zolnierkiewicz
Michal Vokáč
Markus Elfring
Bastian Stender
Arnd Bergmann
Tomi Valkeinen
Jyri Sarha
LABBE Corentin
Julia Lawall
Linus Torvalds
Boris Brezillon
Julian Scheel
Olliver Schinagl
Olliver Schinagl
Krzysztof Kozlowski
Thomas Niederprüm
Dan Carpenter
Prabhakar Lad