| Age | Commit message (Collapse) | Author |
|---|
|
2.3.1.2 failures
commit 23e26d0577535f5ffe4ff8ed6d06e009553c0bca upstream.
The patch addresses the compliance test failures while running TDA
2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered, while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.
TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.
UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].
This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."
With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.
Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS", the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e. tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bed97b30968ba354035a020989df0623e52b5536 upstream.
Commit 081da1325d35 ("usb: typec: ucsi: displayport: Fix a potential race
during registration") made the ucsi code hold con->lock in
ucsi_register_displayport(). But we really don't want any interactions
with the connector to run before the port-registration process is fully
complete.
This commit moves the taking of con->lock from ucsi_register_displayport()
into ucsi_register_port() to achieve this.
Cc: stable@vger.kernel.org
Fixes: 081da1325d35 ("usb: typec: ucsi: displayport: Fix a potential race during registration")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25794e3079d2a98547b6bf5764ef0240aa89b798 upstream.
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
Push the taking of the lock down into these 2 functions, renaming
ucsi_run_command() to ucsi_send_command() which was an existing
wrapper already taking the lock for its callers.
This simplifies things for the callers and removes the difference
between ucsi_send_command() and ucsi_run_command() which has led
to various locking bugs in the past.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e90057f125c8c852940b848e06e7a72f050fc6f upstream.
Fix 2 unlocked ucsi_run_command calls:
1. ucsi_handle_connector_change() contains one ucsi_send_command() call,
which takes the ppm_lock for it; and one ucsi_run_command() call which
relies on the caller have taking the ppm_lock.
ucsi_handle_connector_change() does not take the lock, so the
second (ucsi_run_command) calls should also be ucsi_send_command().
2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which
does not hold the ppm_lock, so it also must use ucsi_send_command().
This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to
ucsi_run_command() to avoid similar problems getting re-introduced in
the future.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ff0705a2ef2929e9326c95df48bdbebb0dafaad upstream.
Lockdep reports an AB BA lock inversion between ucsi_init() and
ucsi_handle_connector_change():
AB order:
1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the
duration of the function)
2. usci_init eventually end up calling ucsi_register_displayport,
which takes ucsi_connector->lock
BA order:
1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock
2. ucsi_handle_connector_change calls ucsi_send_command which takes
ucsi->ppm_lock
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
This commit fixes the AB BA lock inversion by making ucsi_init drop the
ucsi->ppm_lock before it starts registering ports; and replacing any
ucsi_run_command() calls after this point with ucsi_send_command()
(which is a wrapper around run_command taking the lock while handling
the command).
Some of the replacing of ucsi_run_command with ucsi_send_command
in the helpers used during port registration also fixes a number of
code paths after registration which call ucsi_run_command() without
holding the ppm_lock:
1. ucsi_altmode_update_active() call in ucsi/displayport.c
2. ucsi_register_altmodes() call from ucsi_handle_connector_change()
(through ucsi_partner_change())
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d5643d2249b279077427b2c2b2ffae9b70c95b0b upstream.
When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.
After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.
Trigger a reprobe ourselves when new specialised drivers get registered.
Fixes: 88b7381a939d ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adb6e6ac20eedcf1dce19dc75b224e63c0828ea1 upstream.
We only ever used the ID table matching before, but we should also support
open-coded match functions.
Fixes: 88b7381a939de ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 20934c0de13b49a072fb1e0ca79fe0fe0e40eae5 upstream.
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4b9d8a582f738c24ebeabce5cc15f4b8159d74e upstream.
Clang static analysis reports this error
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
memcpy(&acm->notification_buffer[acm->nb_index],
urb->transfer_buffer, copy_size);
When a resize happens, anything before
notification_buffer[acm->nb_index] is garbage.
The third problem is the acm->nb_index is not reset on a
resizing buffer error.
So switch resizing to using krealloc and reassign dr and
reset nb_index.
Fixes: ea2583529cd1 ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc9a2e226ea95e1699f7590845554de095308b75 upstream.
Currently dwc3 doesn't handle usb_request->zero for SG requests. This
change checks and prepares extra TRBs for the ZLP for SG requests.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: 04c03d10e507 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2ee3ff79e6a3d4105e684021017d100524dc560 upstream.
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: d6e5a549cc4d ("usb: dwc3: simplify ZLP handling")
Fixes: 04c03d10e507 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d187c0454ef4c5e046a81af36882d4d515922ec upstream.
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
Cc: <stable@vger.kernel.org> # v4.18+
Fixes: a31e63b608ff ("usb: dwc3: gadget: Correct handling of scattergather lists")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bfd08d06d978d0304eb6f7855b548aa2cd1c5486 upstream.
Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b74b0a04d3e9f9f08ff026e5663dce88ff94e52 upstream.
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1cd1b65afba95971fa457dfdb2c941c60d38c5b upstream.
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d4169834628d18b2392a2da92b7fbf5e8e2ce89 upstream.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 62194244cf87 ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9aa37788e7ebb3f489fb4b71ce07adadd444264a upstream.
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 068834a2773b6a12805105cfadbb3d4229fc6e0a upstream.
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4f2 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5967116e8358899ebaa22702d09b0af57fef23e1 upstream.
There's another Raydium touchscreen needs the no-lpm quirk:
[ 1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[ 1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.339151] usb 1-9: Product: Raydium Touch System
[ 1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[ 6.450497] usb 1-9: can't set config #1, error -110
BugLink: https://bugs.launchpad.net/bugs/1889446
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200731051622.28643-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a469bc9f32dd33c7aac5744669d21a023a719cd upstream.
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f176ede3a3bde5b398a6777a7f9ff091baa2d3ff upstream.
The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:
do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000370c7c68>] prepare_to_wait+0xb1/0x2a0 kernel/sched/wait.c:247
WARNING: CPU: 1 PID: 340 at kernel/sched/core.c:7253 __might_sleep+0x135/0x190
kernel/sched/core.c:7253
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 340 Comm: syz-executor677 Not tainted 5.8.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
panic+0x2aa/0x6e1 kernel/panic.c:231
__warn.cold+0x20/0x50 kernel/panic.c:600
report_bug+0x1bd/0x210 lib/bug.c:198
handle_bug+0x41/0x80 arch/x86/kernel/traps.c:234
exc_invalid_op+0x14/0x40 arch/x86/kernel/traps.c:254
asm_exc_invalid_op+0x12/0x20 arch/x86/include/asm/idtentry.h:536
RIP: 0010:__might_sleep+0x135/0x190 kernel/sched/core.c:7253
Code: 65 48 8b 1c 25 40 ef 01 00 48 8d 7b 10 48 89 fe 48 c1 ee 03 80 3c 06 00 75
2b 48 8b 73 10 48 c7 c7 e0 9e 06 86 e8 ed 12 f6 ff <0f> 0b e9 46 ff ff ff e8 1f
b2 4b 00 e9 29 ff ff ff e8 15 b2 4b 00
RSP: 0018:ffff8881cdb77a28 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8881c6458000 RCX: 0000000000000000
RDX: ffff8881c6458000 RSI: ffffffff8129ec93 RDI: ffffed1039b6ef37
RBP: ffffffff86fdade2 R08: 0000000000000001 R09: ffff8881db32f54f
R10: 0000000000000000 R11: 0000000030343354 R12: 00000000000001f2
R13: 0000000000000000 R14: 0000000000000068 R15: ffffffff83c1b1aa
slab_pre_alloc_hook.constprop.0+0xea/0x200 mm/slab.h:498
slab_alloc_node mm/slub.c:2816 [inline]
slab_alloc mm/slub.c:2900 [inline]
kmem_cache_alloc_trace+0x46/0x220 mm/slub.c:2917
kmalloc include/linux/slab.h:554 [inline]
dummy_urb_enqueue+0x7a/0x880 drivers/usb/gadget/udc/dummy_hcd.c:1251
usb_hcd_submit_urb+0x2b2/0x22d0 drivers/usb/core/hcd.c:1547
usb_submit_urb+0xb4e/0x13e0 drivers/usb/core/urb.c:570
yurex_write+0x3ea/0x820 drivers/usb/misc/yurex.c:495
This patch changes the call to use GFP_ATOMIC instead of GFP_KERNEL.
Reported-and-tested-by: syzbot+c2c3302f9c601a4b1be2@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810182954.GB307778@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a2f2974f26542b4e7b9b4321edb3cbbf3eeb91a upstream.
Commit 88b7381a939d ("USB: Select better matching USB drivers when
available") introduced the use of a "match" function to select a
non-generic/better driver for a particular USB device. This
unfortunately breaks the operation of usbip in general, as reported in
the kernel bugzilla with bug 208267 (linked below).
Upon inspecting the aforementioned commit, one can observe that the
original code in the usb_device_match function used to return 1
unconditionally, but the aforementioned commit makes the usb_device_match
function use identifier tables and "match" virtual functions, if either of
them are available.
Hence, this commit implements a match function for usbip that
unconditionally returns true to ensure that usbip is functional again.
This change has been verified to restore usbip functionality, with a
v5.7.y kernel on an up-to-date version of Qubes OS 4.0, which uses
usbip to redirect USB devices between VMs.
Thanks to Jonathan Dieter for the effort in bisecting this issue down
to the aforementioned commit.
Fixes: 88b7381a939d ("USB: Select better matching USB drivers when available")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208267
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1856443
Link: https://github.com/QubesOS/qubes-issues/issues/5905
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: <stable@vger.kernel.org> # 5.7
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200810160017.46002-1-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1ec7ae6c9f8c016db320e204cb519a1da1581b8 upstream.
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)
Before commit f5249461b504 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:
EP not empty, refuse reset
xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set
So all the subsequent urb sumbits to the ep will fail with the
warn log:
Can't enqueue URB while manually clearing toggle
We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.
Fixes: f5249461b504 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 904df64a5f4d5ebd670801d869ca0a6d6a6e8df6 upstream.
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0077b1b2c8d9ad5f7a08b62fb8524cdb9938388f upstream.
dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get
the ep context.
[rename dci to ep_index -Mathias]
Cc: stable <stable@vger.kernel.org> # v4.15+
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d54343a87732726b04ac5af873916b5ed4f52932 upstream.
tegra_xusb_get_phy() should take input argument "name".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811092553.657762-1-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 316a2868bc269be8c6e69ccc3a1f902a3f518eb9 upstream.
tegra_xusb_init_usb_phy() should initialize "otg_usb2_port" and
"otg_usb3_port" with -EINVAL because "0" is a valid value
represents usb2 port 0 or usb3 port 0.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811093143.699541-1-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d66a57be2f9a315fc10d0f524f670fec903e0fb4 upstream.
Some devices in wild are reporting bunch of firmware versions, so remove
the check for versions in driver
Reported by: Anastasios Vacharakis <vacharakis@gmail.com>
Reported by: Glen Journeay <journeay@gmail.com>
Fixes: 2478be82de44 ("usb: renesas-xhci: Add ROM loader for uPD720201")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208911
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200818071739.789720-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 531412492ce93ea29b9ca3b4eb5e3ed771f851dd upstream.
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 07c8434150f4eb0b65cae288721c8af1080fde17 ]
If a memory allocation fails within a 'usb_ep_alloc_request()' call, the
already allocated memory must be released.
Fix a mix-up in the code and free the correct requests.
Fixes: c52661d60f63 ("usb-gadget: Initial merge of target module for UASP + BOT")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b53a19284f537168fb506f2f40d7fda40a01162 ]
The char buffer buf, receives data directly from user space,
so its content might be negative and its elements are left
shifted to form an unsigned integer.
Since left shifting a negative value is undefined behavior, thus
change the char to u8 to elimintate this UB.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Link: https://lore.kernel.org/r/20200711043018.928-1-charley.ashbringer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce054039ba5e47b75a3be02a00274e52b06a6456 ]
Clean up receive processing by dropping the character pointer and
keeping the length argument unchanged throughout the function.
Also make it more apparent that sysrq processing can consume a
characters by adding an explicit continue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab4cc4ef6724ea588e835fc1e764c4b4407a70b7 ]
Use an unsigned type for the process-packet buffer argument and give it
a more apt name.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 95f5acfc4f58f01a22b66d8c9c0ffb72aa96271c upstream.
During the endpoint dequeue operation, it changes dequeued TRB as link
TRB, when the endpoint is disabled and re-enabled, the DMA fetches the
TRB before the link TRB, after it handles current TRB, the DMA pointer
will advance to the TRB after link TRB, but enqueue and dequene
variables don't know it due to no hardware interrupt at the time, when
the next TRB is added to link TRB position, the DMA will not handle
this TRB due to its pointer is already at the next TRB. See the trace
log like below:
file-storage-675 [001] d..1 86.585657: usb_ep_queue: ep0: req 00000000df9b3a4f length 0/0 sgs 0/0 stream 0 zsI status 0 --> 0
file-storage-675 [001] d..1 86.585663: cdns3_ep_queue: ep1out: req: 000000002ebce364, req buff 00000000f5bc96b4, length: 0/1024 zsi, status: -115, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0
file-storage-675 [001] d..1 86.585671: cdns3_prepare_trb: ep1out: trb 000000007f770303, dma buf: 0xbd195800, size: 1024, burst: 128 ctrl: 0x00000425 (C=1, T=0, ISP, IOC, Normal) SID:0 LAST_SID:0
file-storage-675 [001] d..1 86.585676: cdns3_ring:
Ring contents for ep1out:
Ring deq index: 0, trb: 000000007f770303 (virt), 0xc4003000 (dma)
Ring enq index: 1, trb: 0000000049c1ba21 (virt), 0xc400300c (dma)
free trbs: 38, CCS=1, PCS=1
@0x00000000c4003000 bd195800 80020400 00000425
@0x00000000c400300c c4003018 80020400 00001811
@0x00000000c4003018 bcfcc000 0000001f 00000426
@0x00000000c4003024 bcfce800 0000001f 00000426
...
irq/144-5b13000-698 [000] d... 87.619286: usb_gadget_giveback_request: ep1in: req 0000000031b832eb length 13/13 sgs 0/0 stream 0 zsI status 0 --> 0
file-storage-675 [001] d..1 87.619287: cdns3_ep_queue: ep1out: req: 000000002ebce364, req buff 00000000f5bc96b4, length: 0/1024 zsi, status: -115, trb: [start:0, end:0: virt addr 0x80020400c400300c], flags:0 SID: 0
file-storage-675 [001] d..1 87.619294: cdns3_prepare_trb: ep1out: trb 0000000049c1ba21, dma buf: 0xbd198000, size: 1024, burst: 128 ctrl: 0x00000425 (C=1, T=0, ISP, IOC, Normal) SID:0 LAST_SID:0
file-storage-675 [001] d..1 87.619297: cdns3_ring:
Ring contents for ep1out:
Ring deq index: 1, trb: 0000000049c1ba21 (virt), 0xc400300c (dma)
Ring enq index: 2, trb: 0000000059b34b67 (virt), 0xc4003018 (dma)
free trbs: 38, CCS=1, PCS=1
@0x00000000c4003000 bd195800 0000001f 00000427
@0x00000000c400300c bd198000 80020400 00000425
@0x00000000c4003018 bcfcc000 0000001f 00000426
@0x00000000c4003024 bcfce800 0000001f 00000426
...
file-storage-675 [001] d..1 87.619305: cdns3_doorbell_epx: ep1out, ep_trbaddr c4003018
file-storage-675 [001] .... 87.619308: usb_ep_queue: ep1out: req 000000002ebce364 length 0/1024 sgs 0/0 stream 0 zsI status -115 --> 0
irq/144-5b13000-698 [000] d..1 87.619315: cdns3_epx_irq: IRQ for ep1out: 01000c80 TRBERR , ep_traddr: c4003018 ep_last_sid: 00000000 use_streams: 0
irq/144-5b13000-698 [000] d..1 87.619395: cdns3_usb_irq: IRQ 00000008 = Hot Reset
Fixes: f616c3bda47e ("usb: cdns3: Fix dequeue implementation")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4387b3dbb079d482d3c2b43a703ceed4dd27ed28 upstream.
Assign the .throttle and .unthrottle functions to be generic function
in the driver structure to prevent data loss that can otherwise occur
if the host does not enable USB throttling.
Signed-off-by: Brant Merryman <brant.merryman@silabs.com>
Co-developed-by: Phu Luu <phu.luu@silabs.com>
Signed-off-by: Phu Luu <phu.luu@silabs.com>
Link: https://lore.kernel.org/r/57401AF3-9961-461F-95E1-F8AFC2105F5E@silabs.com
[ johan: fix up tags ]
Fixes: 39a66b8d22a3 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7614ff9b73a1e6fb2b1b51396da132ed22fecdb upstream.
CP210x hardware disables auto-RTS but leaves auto-CTS when in hardware
flow control mode and UART on cp210x hardware is disabled. When
re-opening the port, if auto-CTS is enabled on the cp210x, then auto-RTS
must be re-enabled in the driver.
Signed-off-by: Brant Merryman <brant.merryman@silabs.com>
Co-developed-by: Phu Luu <phu.luu@silabs.com>
Signed-off-by: Phu Luu <phu.luu@silabs.com>
Link: https://lore.kernel.org/r/ECCF8E73-91F3-4080-BE17-1714BC8818FB@silabs.com
[ johan: fix up tags and problem description ]
Fixes: 39a66b8d22a3 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a9cf8715180b18c62addbfe6f6267b8101903119 ]
As per UAC2 spec (ch. 4.7.2), wTotalLength of AC Interface
Header Descriptor "includes the combined length of this
descriptor header and all Clock Source, Unit and Terminal
descriptors."
Thus add its size to its wTotalLength.
Also after recent changes wTotalLength is calculated
dynamically, update static definition of uac2_ac_header_descriptor
accordingly
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33a06f1300a79cfd461cea0268f05e969d4f34ec ]
When gadget registration fails, one should not call usb_del_gadget_udc().
Ensure this by setting gadget->udc to NULL. Also in case of a failure
there is no need to disable low-level hardware, so return immiedetly
instead of jumping to error_init label.
This fixes the following kernel NULL ptr dereference on gadget failure
(can be easily triggered with g_mass_storage without any module
parameters):
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.8.0-rc5 #3133
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at usb_del_gadget_udc+0x38/0xc4
LR is at __mutex_lock+0x31c/0xb18
...
Process kworker/0:1 (pid: 12, stack limit = 0x(ptrval))
Stack: (0xef121db0 to 0xef122000)
...
[<c076bf3c>] (usb_del_gadget_udc) from [<c0726bec>] (dwc2_hsotg_remove+0x10/0x20)
[<c0726bec>] (dwc2_hsotg_remove) from [<c0711208>] (dwc2_driver_probe+0x57c/0x69c)
[<c0711208>] (dwc2_driver_probe) from [<c06247c0>] (platform_drv_probe+0x6c/0xa4)
[<c06247c0>] (platform_drv_probe) from [<c0621df4>] (really_probe+0x200/0x48c)
[<c0621df4>] (really_probe) from [<c06221e8>] (driver_probe_device+0x78/0x1fc)
[<c06221e8>] (driver_probe_device) from [<c061fcd4>] (bus_for_each_drv+0x74/0xb8)
[<c061fcd4>] (bus_for_each_drv) from [<c0621b54>] (__device_attach+0xd4/0x16c)
[<c0621b54>] (__device_attach) from [<c0620c98>] (bus_probe_device+0x88/0x90)
[<c0620c98>] (bus_probe_device) from [<c06211b0>] (deferred_probe_work_func+0x3c/0xd0)
[<c06211b0>] (deferred_probe_work_func) from [<c0149280>] (process_one_work+0x234/0x7dc)
[<c0149280>] (process_one_work) from [<c014986c>] (worker_thread+0x44/0x51c)
[<c014986c>] (worker_thread) from [<c0150b1c>] (kthread+0x158/0x1a0)
[<c0150b1c>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xef121fb0 to 0xef121ff8)
...
---[ end trace 9724c2fc7cc9c982 ]---
While fixing this also fix the double call to dwc2_lowlevel_hw_disable()
if dr_mode is set to USB_DR_MODE_PERIPHERAL. In such case low-level
hardware is already disabled before calling usb_add_gadget_udc(). That
function correctly preserves low-level hardware state, there is no need
for the second unconditional dwc2_lowlevel_hw_disable() call.
Fixes: 207324a321a8 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a410953d1fb4dbe91ffcfdee9cbbf889d19b0d7 ]
The reset is a shared reset line, but reset_control_reset is still used
and reset_control_deassert is not guaranteed to have been called before
the first reset_control_assert call. When suspending the following
warning may be seen:
WARNING: CPU: 1 PID: 5530 at drivers/reset/core.c:355 reset_control_assert+0x184/0x19c
Hardware name: Hardkernel ODROID-N2 (DT)
[..]
pc : reset_control_assert+0x184/0x19c
lr : dwc3_meson_g12a_suspend+0x68/0x7c
[..]
Call trace:
reset_control_assert+0x184/0x19c
dwc3_meson_g12a_suspend+0x68/0x7c
platform_pm_suspend+0x28/0x54
__device_suspend+0x590/0xabc
dpm_suspend+0x104/0x404
dpm_suspend_start+0x84/0x1bc
suspend_devices_and_enter+0xc4/0x4fc
pm_suspend+0x198/0x2d4
Fixes: 6d9fa35a347a87 ("usb: dwc3: meson-g12a: get the reset as shared")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1b6bed3b5036509b449b5965285d5057ba42527 ]
The function quirks_param_set() takes as argument a const char* pointer
to the new value of the usbcore.quirks parameter. It then casts this
pointer to a non-const char* pointer and passes it to the strsep()
function, which overwrites the value.
Fix this by creating a copy of the value using kstrdup() and letting
that copy be written to by strsep().
Fixes: 027bd6cafd9a ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Kars Mulder <kerneldev@karsmulder.nl>
Link: https://lore.kernel.org/r/5ee2-5f048a00-21-618c5c00@230659773
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de37458f8c2bfc465500a1dd0d15dbe96d2a698c ]
The set-led command is eight bytes long and starts with a command byte
followed by six bytes of RGB data and ends with a byte encoding a
frequency (see iuu_led() and iuu_rgbf_fill_buffer()).
The led activity helpers had a few long-standing bugs which corrupted
the command packets by inserting a second command byte and thereby
offsetting the RGB data and dropping the frequency in non-xmas mode.
In xmas mode, a related off-by-one error left the frequency field
uninitialised.
Fixes: 60a8fc017103 ("USB: add iuu_phoenix driver")
Reported-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/r/20200716085056.31471-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5fc453d7de3d0c345812453823a3a56783c5f82c ]
GISB bus error kernel panics have been observed during S2 transition
tests on the 7271t platform. The errors are a result of the BDC
interrupt handler trying to access BDC register space after the
system's suspend callbacks have completed.
Adding a suspend hook to the BDC driver that halts the controller before
S2 entry thus preventing unwanted access to the BDC register space during
this transition.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a95bdfd22076497288868c028619bc5995f5cc7f ]
Multiple connects/disconnects can cause a crash on the second
disconnect. The driver had a problem where it would try to send
endpoint commands after it was disconnected which is not allowed
by the hardware. The fix is to only allow the endpoint commands
when the endpoint is connected. This will also fix issues that
showed up when using configfs to create gadgets.
Signed-off-by: Sasi Kumar <sasi.kumar@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2468c877da428ebfd701142c4cdfefcfb7d4c00e ]
Driver does not release memory for device on error handling paths in
net2280_probe() when gadget_release() is not registered yet.
The patch fixes the bug like in other similar drivers.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f1e51e99ed498d4aa9ae5df28e43d558ea627781 ]
If not clear u3port's dual mode when disable device, the IP
will fail to enter sleep mode when suspend.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ec37198acca7b4c17b96247697406e47aafe0605 upstream.
I've confirmed that the ASMedia ASM1142 has the same problem as the
ASM2142/ASM3142, in that it too reports that it supports 64-bit DMA
addresses when in fact it does not. As with the ASM2142/ASM3142, this
can cause problems on systems where the upper bits matter, and adding
the XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200728042408.180529-3-cyrozap@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1841cb255da41e87bed9573915891d056f80e2e7 upstream.
Not all ASMedia host controllers have a device ID that matches its part
number. #define some of these IDs to make it clearer at a glance which
chips require what quirks.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Link: https://lore.kernel.org/r/20200728042408.180529-2-cyrozap@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17a82716587e9d7c3b246a789add490b2b5dcab6 upstream.
In previous patches that added support for new iowarrior devices, the
handling of the report size was not done correct.
Fix that up and update the copyright date for the driver
Reworked from an original patch written by Christoph Jung.
Fixes: bab5417f5f01 ("USB: misc: iowarrior: add support for the 100 device")
Fixes: 5f6f8da2d7b5 ("USB: misc: iowarrior: add support for the 28 and 28L devices")
Fixes: 461d8deb26a7 ("USB: misc: iowarrior: add support for 2 OEMed devices")
Cc: stable <stable@kernel.org>
Reported-by: Christoph Jung <jung@codemercs.com>
Link: https://lore.kernel.org/r/20200726094939.1268978-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2a4309c1ab6df424b2239fe2920d6f26f808d17 upstream.
When running qmi-firmware-update on the Sierra Wireless EM7305 in a Toshiba
laptop, it changed product ID to 0x9062 when entering QDL mode:
usb 2-4: new high-speed USB device number 78 using xhci_hcd
usb 2-4: New USB device found, idVendor=1199, idProduct=9062, bcdDevice= 0.00
usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-4: Product: EM7305
usb 2-4: Manufacturer: Sierra Wireless, Incorporated
The upgrade could complete after running
# echo 1199 9062 > /sys/bus/usb-serial/drivers/qcserial/new_id
qcserial 2-4:1.0: Qualcomm USB modem converter detected
usb 2-4: Qualcomm USB modem converter now attached to ttyUSB0
Signed-off-by: Erik Ekman <erik@kryo.se>
Link: https://lore.kernel.org/r/20200717185118.3640219-1-erik@kryo.se
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 5c4e8d3781bc ("usb: host: xhci-tegra: Add support for XUSB
context save/restore") is using the IPFS 'num_offsets' value when
allocating memory for FPCI context instead of the FPCI 'num_offsets'.
After commit cad064f1bd52 ("devres: handle zero size in devm_kmalloc()")
was added system suspend started failing on Tegra186. The kernel log
showed that the Tegra XHCI driver was crashing on entry to suspend when
attempting the save the USB context. On Tegra186, the IPFS context has a
zero length but the FPCI content has a non-zero length, and because of
the bug in the Tegra XHCI driver we are incorrectly allocating a zero
length array for the FPCI context. The crash seen on entering suspend
when we attempt to save the FPCI context and following commit
cad064f1bd52 ("devres: handle zero size in devm_kmalloc()") this now
causes a NULL pointer deference when we access the memory. Fix this by
correcting the amount of memory we are allocating for FPCI contexts.
Cc: stable@vger.kernel.org
Fixes: 5c4e8d3781bc ("usb: host: xhci-tegra: Add support for XUSB context save/restore")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200715113842.30680-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Badhri Jagan Sridharan
Hans de Goede
Bastien Nocera
Alan Stern
Tom Rix
Thinh Nguyen
Andy Shevchenko
Brooke Basile
Tang Bin
Cyril Roelandt
Kai-Heng Feng
M. Vefa Bicakci
Ding Hui
Li Jun
JC Kuo
Vinod Koul
Evgeny Novikov
Christophe JAILLET
Changming Liu
Johan Hovold
Peter Chen
Brant Merryman
Ruslan Bilovol
Marek Szyprowski
Dan Robertson
Kars Mulder
Danesh Petigara
Sasi Kumar
Chunfeng Yun
Forest Crossman
Greg Kroah-Hartman
Erik Ekman
Jon Hunter