Age | Commit message (Collapse) | Author |
|
commit ea422312a462696093b5db59d294439796cba4ad upstream.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes: 0f64478cbc7a ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e696d00e65e81d46e911f24b12e441037bf11b38 upstream.
Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 91feb01596e5efc0cc922cc73f5583114dccf4d2 upstream.
The work item can operate on
1. stale memory left over from the last transfer
the actual length of the data transfered needs to be checked
2. memory already freed
the error handling in appledisplay_probe() needs
to cancel the work in that case
Reported-and-tested-by: syzbot+495dab1f175edc9c2f13@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106124902.7765-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 92aa5986f4f7b5a8bf282ca0f50967f4326559f5 upstream.
In case of a timeout or if a signal aborts a read
communication with the device needs to be ended
lest we overwrite an active URB the next time we
do IO to the device, as the URB may still be active.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191107142856.16774-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 347bc8cb26388791c5881a3775cb14a3f765a674 upstream.
Add support for the Mark-10 digital force gauge device to the cp201x
driver.
Based on a report and a larger patch from Joel Jennings
Reported-by: Joel Jennings <joel.jennings@makeitlabs.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191118092119.GA153852@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1ec13abac58b6f24e32f0d3081ef4e7456e62ed8 upstream.
USBIP uses lib/scatterlist.h
Hence it needs to set CONFIG_SGL_ALLOC
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191112154939.21217-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.28 stable release
# gpg: Signature made Sun 29 Dec 2019 05:29:45 PM EST
# gpg: using RSA key EBCE84042C07D1D6
# gpg: Can't check signature: No public key
|
|
commit 2a9125317b247f2cf35c196f968906dcf062ae2d upstream.
Smatch reported that nents is not initialized and used in
stub_recv_cmd_submit(). nents is currently initialized by sgl_alloc()
and used to allocate multiple URBs when host controller doesn't
support scatter-gather DMA. The use of uninitialized nents means that
buf_len is zero and use_sg is true. But buffer length should not be
zero when an URB uses scatter-gather DMA.
To prevent this situation, add the conditional that checks buf_len
and use_sg. And move the use of nents right after the sgl_alloc() to
avoid the use of uninitialized nents.
If the error occurs, it adds SDEV_EVENT_ERROR_MALLOC and stub_priv
will be released by stub event handler and connection will be shut
down.
Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191111141035.27788-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 093edc2baad2c258b1f55d1ab9c63c2b5ae67e42 upstream.
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Fixes: 1a1c851bbd70 ("usb: gadget: configfs: fix concurrent issue between composite APIs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191030034046.188808-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d4d8257754c3300ea2a465dadf8d2b02c713c920 upstream.
iso_buffer should be set to NULL after use and free in the while loop.
In the case of isochronous URB in the while loop, iso_buffer is
allocated and after sending it to server, buffer is deallocated. And
then, if the next URB in the while loop is not a isochronous pipe,
iso_buffer still holds the previously deallocated buffer address and
kfree tries to free wrong buffer address.
Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191022093017.8027-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d8eca64eec7103ab1fbabc0a187dbf6acfb2af93 upstream.
When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bdef4 "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 88f6bf3846ee90bf33aa1ce848cd3bfb3229f4a4 upstream.
A recent info-leak bug manifested itself along with warning about a
negative buffer overflow:
ldusb 1-1:0.28: Read buffer overflow, -131383859965943 bytes dropped
when it was really a rather large positive one.
A sanity check that prevents this has now been put in place, but let's
fix up the size format specifiers, which should all be unsigned.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d482c7bb0541d19dea8bff437a9f3c5563b5b2d2 upstream.
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.
Currently the USB core does not check for endpoints having a maxpacket
value of 0. This patch adds a check, printing a warning and skipping
over any endpoints it catches.
Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a7d9874c6f3fbc8d25cd9ceba35b6822612c4ebf upstream.
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1a1c851bbd706ea9f3a9756c2d3db28523506d3b upstream.
We meet several NULL pointer issues if configfs_composite_unbind
and composite_setup (or composite_disconnect) are running together.
These issues occur when do the function switch stress test, the
configfs_compsoite_unbind is called from user mode by
echo "" to /sys/../UDC entry, and meanwhile, the setup interrupt
or disconnect interrupt occurs by hardware. The composite_setup
will get the cdev from get_gadget_data, but configfs_composite_unbind
will set gadget data as NULL, so the NULL pointer issue occurs.
This concurrent is hard to reproduce by native kernel, but can be
reproduced by android kernel.
In this commit, we introduce one spinlock belongs to structure
gadget_info since we can't use the same spinlock in usb_composite_dev
due to exclusive running together between composite_setup and
configfs_composite_unbind. And one bit flag 'unbind' to indicate the
code is at unbind routine, this bit is needed due to we release the
lock at during configfs_composite_unbind sometimes, and composite_setup
may be run at that time.
Several oops:
oops 1:
android_work: sent uevent USB_STATE=CONNECTED
configfs-gadget gadget: super-speed config #1: b
android_work: sent uevent USB_STATE=CONFIGURED
init: Received control message 'start' for 'adbd' from pid: 3515 (system_server)
Unable to handle kernel NULL pointer dereference at virtual address 0000002a
init: Received control message 'stop' for 'adbd' from pid: 3375 (/vendor/bin/hw/android.hardware.usb@1.1-servic)
Mem abort info:
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgd = ffff8008f1b7f000
[000000000000002a] *pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 4 PID: 2457 Comm: irq/125-5b11000 Not tainted 4.14.98-07846-g0b40a9b-dirty #16
Hardware name: Freescale i.MX8QM MEK (DT)
task: ffff8008f2a98000 task.stack: ffff00000b7b8000
PC is at composite_setup+0x44/0x1508
LR is at android_setup+0xb8/0x13c
pc : [<ffff0000089ffb3c>] lr : [<ffff000008a032fc>] pstate: 800001c5
sp : ffff00000b7bbb80
x29: ffff00000b7bbb80 x28: ffff8008f2a3c010
x27: 0000000000000001 x26: 0000000000000000 [1232/1897]
audit: audit_lost=25791 audit_rate_limit=5 audit_backlog_limit=64
x25: 00000000ffffffa1 x24: ffff8008f2a3c010
audit: rate limit exceeded
x23: 0000000000000409 x22: ffff000009c8e000
x21: ffff8008f7a8b428 x20: ffff00000afae000
x19: ffff0000089ff000 x18: 0000000000000000
x17: 0000000000000000 x16: ffff0000082b7c9c
x15: 0000000000000000 x14: f1866f5b952aca46
x13: e35502e30d44349c x12: 0000000000000008
x11: 0000000000000008 x10: 0000000000000a30
x9 : ffff00000b7bbd00 x8 : ffff8008f2a98a90
x7 : ffff8008f27a9c90 x6 : 0000000000000001
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 0000000000000000 x2 : 0000000000000006
x1 : ffff0000089ff8d0 x0 : 732a010310b9ed00
X7: 0xffff8008f27a9c10:
9c10 00000002 00000000 00000001 00000000 13110000 ffff0000 00000002 00208040
9c30 00000000 00000000 00000000 00000000 00000000 00000005 00000029 00000000
9c50 00051778 00000001 f27a8e00 ffff8008 00000005 00000000 00000078 00000078
9c70 00000078 00000000 09031d48 ffff0000 00100000 00000000 00400000 00000000
9c90 00000001 00000000 00000000 00000000 00000000 00000000 ffefb1a0 ffff8008
9cb0 f27a9ca8 ffff8008 00000000 00000000 b9d88037 00000173 1618a3eb 00000001
9cd0 870a792a 0000002e 16188fe6 00000001 0000242b 00000000 00000000 00000000
using random self ethernet address
9cf0 019a4646 00000000 000547f3 00000000 ecfd6c33 00000002 00000000
using random host ethernet address
00000000
X8: 0xffff8008f2a98a10:
8a10 00000000 00000000 f7788d00 ffff8008 00000001 00000000 00000000 00000000
8a30 eb218000 ffff8008 f2a98000 ffff8008 f2a98000 ffff8008 09885000 ffff0000
8a50 f34df480 ffff8008 00000000 00000000 f2a98648 ffff8008 09c8e000 ffff0000
8a70 fff2c800 ffff8008 09031d48 ffff0000 0b7bbd00 ffff0000 0b7bbd00 ffff0000
8a90 080861bc ffff0000 00000000 00000000 00000000 00000000 00000000 00000000
8ab0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8ad0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8af0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
X21: 0xffff8008f7a8b3a8:
b3a8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b3c8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b3e8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b408 00000000 00000000 00000000 00000000 00000000 00000000 00000001 00000000
b428 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
b448 0053004d 00540046 00300031 00010030 eb07b520 ffff8008 20011201 00000003
b468 e418d109 0104404e 00010302 00000000 eb07b558 ffff8008 eb07b558 ffff8008
b488 f7a8b488 ffff8008 f7a8b488 ffff8008 f7a8b300 ffff8008 00000000 00000000
X24: 0xffff8008f2a3bf90:
bf90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfd0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
c010 00000000 00000000 f2a3c018 ffff8008 f2a3c018 ffff8008 08a067dc ffff0000
c030 f2a5a000 ffff8008 091c3650 ffff0000 f716fd18 ffff8008 f716fe30 ffff8008
c050 f2ce4a30 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
c070 f76c8010 ffff8008 f2ce4b00 ffff8008 095cac68 ffff0000 f2a5a028 ffff8008
X28: 0xffff8008f2a3bf90:
bf90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfd0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
c010 00000000 00000000 f2a3c018 ffff8008 f2a3c018 ffff8008 08a067dc ffff0000
c030 f2a5a000 ffff8008 091c3650 ffff0000 f716fd18 ffff8008 f716fe30 ffff8008
c050 f2ce4a30 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
c070 f76c8010 ffff8008 f2ce4b00 ffff8008 095cac68 ffff0000 f2a5a028 ffff8008
Process irq/125-5b11000 (pid: 2457, stack limit = 0xffff00000b7b8000)
Call trace:
Exception stack(0xffff00000b7bba40 to 0xffff00000b7bbb80)
ba40: 732a010310b9ed00 ffff0000089ff8d0 0000000000000006 0000000000000000
ba60: 0000000000000001 0000000000000000 0000000000000001 ffff8008f27a9c90
ba80: ffff8008f2a98a90 ffff00000b7bbd00 0000000000000a30 0000000000000008
baa0: 0000000000000008 e35502e30d44349c f1866f5b952aca46 0000000000000000
bac0: ffff0000082b7c9c 0000000000000000 0000000000000000 ffff0000089ff000
bae0: ffff00000afae000 ffff8008f7a8b428 ffff000009c8e000 0000000000000409
bb00: ffff8008f2a3c010 00000000ffffffa1 0000000000000000 0000000000000001
bb20: ffff8008f2a3c010 ffff00000b7bbb80 ffff000008a032fc ffff00000b7bbb80
bb40: ffff0000089ffb3c 00000000800001c5 ffff00000b7bbb80 732a010310b9ed00
bb60: ffffffffffffffff ffff0000080f777c ffff00000b7bbb80 ffff0000089ffb3c
[<ffff0000089ffb3c>] composite_setup+0x44/0x1508
[<ffff000008a032fc>] android_setup+0xb8/0x13c
[<ffff0000089bd9a8>] cdns3_ep0_delegate_req+0x44/0x70
[<ffff0000089bdff4>] cdns3_check_ep0_interrupt_proceed+0x33c/0x654
[<ffff0000089bca44>] cdns3_device_thread_irq_handler+0x4b0/0x4bc
[<ffff0000089b77b4>] cdns3_thread_irq+0x48/0x68
[<ffff000008145bf0>] irq_thread_fn+0x28/0x88
[<ffff000008145e38>] irq_thread+0x13c/0x228
[<ffff0000080fed70>] kthread+0x104/0x130
[<ffff000008085064>] ret_from_fork+0x10/0x18
oops2:
composite_disconnect: Calling disconnect on a Gadget that is not connected
android_work: did not send uevent (0 0 (null))
init: Received control message 'stop' for 'adbd' from pid: 3359 (/vendor/bin/hw/android.hardware.usb@1.1-service.imx)
init: Sending signal 9 to service 'adbd' (pid 22343) process group...
------------[ cut here ]------------
audit: audit_lost=180038 audit_rate_limit=5 audit_backlog_limit=64
audit: rate limit exceeded
WARNING: CPU: 0 PID: 3468 at kernel_imx/drivers/usb/gadget/composite.c:2009 composite_disconnect+0x80/0x88
Modules linked in:
CPU: 0 PID: 3468 Comm: HWC-UEvent-Thre Not tainted 4.14.98-07846-g0b40a9b-dirty #16
Hardware name: Freescale i.MX8QM MEK (DT)
task: ffff8008f2349c00 task.stack: ffff00000b0a8000
PC is at composite_disconnect+0x80/0x88
LR is at composite_disconnect+0x80/0x88
pc : [<ffff0000089ff9b0>] lr : [<ffff0000089ff9b0>] pstate: 600001c5
sp : ffff000008003dd0
x29: ffff000008003dd0 x28: ffff8008f2349c00
x27: ffff000009885018 x26: ffff000008004000
Timeout for IPC response!
x25: ffff000009885018 x24: ffff000009c8e280
x23: ffff8008f2d98010 x22: 00000000000001c0
x21: ffff8008f2d98394 x20: ffff8008f2d98010
x19: 0000000000000000 x18: 0000e3956f4f075a
fxos8700 4-001e: i2c block read acc failed
x17: 0000e395735727e8 x16: ffff00000829f4d4
x15: ffffffffffffffff x14: 7463656e6e6f6320
x13: 746f6e2009090920 x12: 7369207461687420
x11: 7465676461472061 x10: 206e6f207463656e
x9 : 6e6f637369642067 x8 : ffff000009c8e280
x7 : ffff0000086ca6cc x6 : ffff000009f15e78
x5 : 0000000000000000 x4 : 0000000000000000
x3 : ffffffffffffffff x2 : c3f28b86000c3900
x1 : c3f28b86000c3900 x0 : 000000000000004e
X20: 0xffff8008f2d97f90:
7f90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
libprocessgroup: Failed to kill process cgroup uid 0 pid 22343 in 215ms, 1 processes remain
7fd0
Timeout for IPC response!
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
using random self ethernet address
7ff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
8010 00000100 00000000 f2d98018 ffff8008 f2d98018 ffff8008 08a067dc
using random host ethernet address
ffff0000
8030 f206d800 ffff8008 091c3650 ffff0000 f7957b18 ffff8008 f7957730 ffff8008
8050 f716a630 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
8070 f76c8010 ffff8008 f716a800 ffff8008 095cac68 ffff0000 f206d828 ffff8008
X21: 0xffff8008f2d98314:
8314 ffff8008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8334 00000000 00000000 00000000 00000000 00000000 08a04cf4 ffff0000 00000000
8354 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
8374 00000000 00000000 00000000 00001001 00000000 00000000 00000000 00000000
8394 e4bbe4bb 0f230000 ffff0000 0afae000 ffff0000 ae001000 00000000 f206d400
Timeout for IPC response!
83b4 ffff8008 00000000 00000000 f7957b18 ffff8008 f7957718 ffff8008 f7957018
83d4 ffff8008 f7957118 ffff8008 f7957618 ffff8008 f7957818 ffff8008 f7957918
83f4 ffff8008 f7957d18 ffff8008 00000000 00000000 00000000 00000000 00000000
X23: 0xffff8008f2d97f90:
7f90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fd0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7ff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008
8010 00000100 00000000 f2d98018 ffff8008 f2d98018 ffff8008 08a067dc ffff0000
8030 f206d800 ffff8008 091c3650 ffff0000 f7957b18 ffff8008 f7957730 ffff8008
8050 f716a630 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000
8070 f76c8010 ffff8008 f716a800 ffff8008 095cac68 ffff0000 f206d828 ffff8008
X28: 0xffff8008f2349b80:
9b80 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9ba0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9bc0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9be0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9c00 00000022 00000000 ffffffff ffffffff 00010001 00000000 00000000 00000000
9c20 0b0a8000 ffff0000 00000002 00404040 00000000 00000000 00000000 00000000
9c40 00000001 00000000 00000001 00000000 001ebd44 00000001 f390b800 ffff8008
9c60 00000000 00000001 00000070 00000070 00000070 00000000 09031d48 ffff0000
Call trace:
Exception stack(0xffff000008003c90 to 0xffff000008003dd0)
3c80: 000000000000004e c3f28b86000c3900
3ca0: c3f28b86000c3900 ffffffffffffffff 0000000000000000 0000000000000000
3cc0: ffff000009f15e78 ffff0000086ca6cc ffff000009c8e280 6e6f637369642067
3ce0: 206e6f207463656e 7465676461472061 7369207461687420 746f6e2009090920
3d00: 7463656e6e6f6320 ffffffffffffffff ffff00000829f4d4 0000e395735727e8
3d20: 0000e3956f4f075a 0000000000000000 ffff8008f2d98010 ffff8008f2d98394
3d40: 00000000000001c0 ffff8008f2d98010 ffff000009c8e280 ffff000009885018
3d60: ffff000008004000 ffff000009885018 ffff8008f2349c00 ffff000008003dd0
3d80: ffff0000089ff9b0 ffff000008003dd0 ffff0000089ff9b0 00000000600001c5
3da0: ffff8008f33f2cd8 0000000000000000 0000ffffffffffff 0000000000000000
init: Received control message 'start' for 'adbd' from pid: 3359 (/vendor/bin/hw/android.hardware.usb@1.1-service.imx)
3dc0: ffff000008003dd0 ffff0000089ff9b0
[<ffff0000089ff9b0>] composite_disconnect+0x80/0x88
[<ffff000008a044d4>] android_disconnect+0x3c/0x68
[<ffff0000089ba9f8>] cdns3_device_irq_handler+0xfc/0x2c8
[<ffff0000089b84c0>] cdns3_irq+0x44/0x94
[<ffff00000814494c>] __handle_irq_event_percpu+0x60/0x24c
[<ffff000008144c0c>] handle_irq_event+0x58/0xc0
[<ffff00000814873c>] handle_fasteoi_irq+0x98/0x180
[<ffff000008143a10>] generic_handle_irq+0x24/0x38
[<ffff000008144170>] __handle_domain_irq+0x60/0xac
[<ffff0000080819c4>] gic_handle_irq+0xd4/0x17c
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1c20c89b0421b52b2417bb0f62a611bc669eda1d upstream.
composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.
Consider the below sequence of function calls:
configfs_composite_bind()
composite_dev_prepare()
- Allocate cdev->req, cdev->req->buf
composite_os_desc_req_prepare()
- Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
composite_dev_cleanup()
- free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
- If it fails goto err_comp_cleanup will call the
composite_dev_cleanup() function
composite_dev_cleanup()
- calls kfree up with the stale values of cdev->req->buf and
cdev->os_desc_req from the previous configfs_composite_bind
call. The free call on these stale values leads to double free.
Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ba3a1a915c49cc3023e4ddfc88f21e7514e82aa4 upstream.
Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.
Fixes: 914a3f3b3754 ("USB: add atmel_usba_udc driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bc1e3a2dd0c9954fd956ac43ca2876bbea018c01 upstream.
Check memory resource existence before releasing it to avoid NULL
pointer dereference
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a51bab592fbbef10f0e42a8aed86adfbf6a68fa7 upstream.
After many randconfig builds, one configuration caused a link
error with dwc3-meson-g12a lacking the regmap-mmio code:
drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe':
dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk'
Add the select statement that we have for all other users
of that dependency.
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ea44d190764b4422af4d1c29eaeb9e69e353b406 upstream.
There are bugs on vhci with usb 3.0 storage device. In USB, each SG
list entry buffer should be divisible by the bulk max packet size.
But with native SG support, this problem doesn't matter because the
SG buffer is treated as contiguous buffer. But without native SG
support, USB storage driver breaks SG list into several URBs and the
error occurs because of a buffer size of URB that cannot be divided
by the bulk max packet size. The error situation is as follows.
When USB Storage driver requests 31.5 KB data and has SG list which
has 3584 bytes buffer followed by 7 4096 bytes buffer for some
reason. USB Storage driver splits this SG list into several URBs
because VHCI doesn't support SG and sends them separately. So the
first URB buffer size is 3584 bytes. When receiving data from device,
USB 3.0 device sends data packet of 1024 bytes size because the max
packet size of BULK pipe is 1024 bytes. So device sends 4096 bytes.
But the first URB buffer has only 3584 bytes buffer size. So host
controller terminates the transfer even though there is more data to
receive. So, vhci needs to support SG transfer to prevent this error.
In this patch, vhci supports SG regardless of whether the server's
host controller supports SG or not, because stub driver splits SG
list into several URBs if the server's host controller doesn't
support SG.
To support SG, vhci sets URB_DMA_MAP_SG flag in urb->transfer_flags
if URB has SG list and this flag will tell stub driver to use SG
list. After receiving urb from stub driver, vhci clear URB_DMA_MAP_SG
flag to avoid unnecessary DMA unmapping in HCD.
vhci sends each SG list entry to stub driver. Then, stub driver sees
the total length of the buffer and allocates SG table and pages
according to the total buffer length calling sgl_alloc(). After stub
driver receives completed URB, it again sends each SG list entry to
vhci.
If the server's host controller doesn't support SG, stub driver
breaks a single SG request into several URBs and submits them to
the server's host controller. When all the split URBs are completed,
stub driver reassembles the URBs into a single return command and
sends it to vhci.
Moreover, in the situation where vhci supports SG, but stub driver
does not, or vice versa, usbip works normally. Because there is no
protocol modification, there is no problem in communication between
server and client even if the one has a kernel without SG support.
In the case of vhci supports SG and stub driver doesn't, because
vhci sends only the total length of the buffer to stub driver as
it did before the patch applied, stub driver only needs to allocate
the required length of buffers using only kmalloc() regardless of
whether vhci supports SG or not. But stub driver has to allocate
buffer with kmalloc() as much as the total length of SG buffer which
is quite huge when vhci sends SG request, so it has overhead in
buffer allocation in this situation.
If stub driver needs to send data buffer to vhci because of IN pipe,
stub driver also sends only total length of buffer as metadata and
then sends real data as vhci does. Then vhci receive data from stub
driver and store it to the corresponding buffer of SG list entry.
And for the case of stub driver supports SG and vhci doesn't, since
the USB storage driver checks that vhci doesn't support SG and sends
the request to stub driver by splitting the SG list into multiple
URBs, stub driver allocates a buffer for each URB with kmalloc() as
it did before this patch.
* Test environment
Test uses two difference machines and two different kernel version
to make mismatch situation between the client and the server where
vhci supports SG, but stub driver does not, or vice versa. All tests
are conducted in both full SG support that both vhci and stub support
SG and half SG support that is the mismatch situation. Test kernel
version is 5.3-rc6 with commit "usb: add a HCD_DMA flag instead of
guestimating DMA capabilities" to avoid unnecessary DMA mapping and
unmapping.
- Test kernel version
- 5.3-rc6 with SG support
- 5.1.20-200.fc29.x86_64 without SG support
* SG support test
- Test devices
- Super-speed storage device - SanDisk Ultra USB 3.0
- High-speed storage device - SMI corporation USB 2.0 flash drive
- Test description
Test read and write operation of mass storage device that uses the
BULK transfer. In test, the client reads and writes files whose size
is over 1G and it works normally.
* Regression test
- Test devices
- Super-speed device - Logitech Brio webcam
- High-speed device - Logitech C920 HD Pro webcam
- Full-speed device - Logitech bluetooth mouse
- Britz BR-Orion speaker
- Low-speed device - Logitech wired mouse
- Test description
Moving and click test for mouse. To test the webcam, use gnome-cheese.
To test the speaker, play music and video on the client. All works
normally.
* VUDC compatibility test
VUDC also works well with this patch. Tests are done with two USB
gadget created by CONFIGFS USB gadget. Both use the BULK pipe.
1. Serial gadget
2. Mass storage gadget
- Serial gadget test
Serial gadget on the host sends and receives data using cat command
on the /dev/ttyGS<N>. The client uses minicom to communicate with
the serial gadget.
- Mass storage gadget test
After connecting the gadget with vhci, use "dd" to test read and
write operation on the client side.
Read - dd if=/dev/sd<N> iflag=direct of=/dev/null bs=1G count=1
Write - dd if=<my file path> iflag=direct of=/dev/sd<N> bs=1G count=1
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190828032741.12234-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.27 stable release
# gpg: Signature made Mon 16 Dec 2019 10:43:54 PM EST
# gpg: using RSA key EBCE84042C07D1D6
# gpg: Can't check signature: No public key
|
|
driver fails
commit 163be6ff7739b12ff300d77897d340f661821da2 upstream.
If a gadget driver is in the pending drivers list, a UDC
becomes available and udc_bind_to_driver() fails, then it
gets deleted from the pending list.
i.e. list_del(&driver->pending) in check_pending_gadget_drivers().
Then if that gadget driver is unregistered,
usb_gadget_unregister_driver() does a list_del(&driver->pending)
again thus causing a page fault as that list entry has been poisoned
by the previous list_del().
Fix this by using list_del_init() instead of list_del() in
check_pending_gadget_drivers().
Test case:
- Make sure no UDC is available
- modprobe g_mass_storage file=wrongfile
- Load UDC driver so it becomes available
lun0: unable to open backing file: wrongfile
- modprobe -r g_mass_storage
[ 60.900431] Unable to handle kernel paging request at virtual address dead000000000108
[ 60.908346] Mem abort info:
[ 60.911145] ESR = 0x96000044
[ 60.914227] Exception class = DABT (current EL), IL = 32 bits
[ 60.920162] SET = 0, FnV = 0
[ 60.923217] EA = 0, S1PTW = 0
[ 60.926354] Data abort info:
[ 60.929228] ISV = 0, ISS = 0x00000044
[ 60.933058] CM = 0, WnR = 1
[ 60.936011] [dead000000000108] address between user and kernel address ranges
[ 60.943136] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 60.948691] Modules linked in: g_mass_storage(-) usb_f_mass_storage libcomposite xhci_plat_hcd xhci_hcd usbcore ti_am335x_adc kfifo_buf omap_rng cdns3 rng_core udc_core crc32_ce xfrm_user crct10dif_ce snd_so6
[ 60.993995] Process modprobe (pid: 834, stack limit = 0x00000000c2aebc69)
[ 61.000765] CPU: 0 PID: 834 Comm: modprobe Not tainted 4.19.59-01963-g065f42a60499 #92
[ 61.008658] Hardware name: Texas Instruments SoC (DT)
[ 61.014472] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 61.019253] pc : usb_gadget_unregister_driver+0x7c/0x108 [udc_core]
[ 61.025503] lr : usb_gadget_unregister_driver+0x30/0x108 [udc_core]
[ 61.031750] sp : ffff00001338fda0
[ 61.035049] x29: ffff00001338fda0 x28: ffff800846d40000
[ 61.040346] x27: 0000000000000000 x26: 0000000000000000
[ 61.045642] x25: 0000000056000000 x24: 0000000000000800
[ 61.050938] x23: ffff000008d7b0d0 x22: ffff0000088b07c8
[ 61.056234] x21: ffff000001100000 x20: ffff000002020260
[ 61.061530] x19: ffff0000010ffd28 x18: 0000000000000000
[ 61.066825] x17: 0000000000000000 x16: 0000000000000000
[ 61.072121] x15: 0000000000000000 x14: 0000000000000000
[ 61.077417] x13: ffff000000000000 x12: ffffffffffffffff
[ 61.082712] x11: 0000000000000030 x10: 7f7f7f7f7f7f7f7f
[ 61.088008] x9 : fefefefefefefeff x8 : 0000000000000000
[ 61.093304] x7 : ffffffffffffffff x6 : 000000000000ffff
[ 61.098599] x5 : 8080000000000000 x4 : 0000000000000000
[ 61.103895] x3 : ffff000001100020 x2 : ffff800846d40000
[ 61.109190] x1 : dead000000000100 x0 : dead000000000200
[ 61.114486] Call trace:
[ 61.116922] usb_gadget_unregister_driver+0x7c/0x108 [udc_core]
[ 61.122828] usb_composite_unregister+0x10/0x18 [libcomposite]
[ 61.128643] msg_cleanup+0x18/0xfce0 [g_mass_storage]
[ 61.133682] __arm64_sys_delete_module+0x17c/0x1f0
[ 61.138458] el0_svc_common+0x90/0x158
[ 61.142192] el0_svc_handler+0x2c/0x80
[ 61.145926] el0_svc+0x8/0xc
[ 61.148794] Code: eb03003f d10be033 54ffff21 a94d0281 (f9000420)
[ 61.154869] ---[ end trace afb22e9b637bd9a7 ]---
Segmentation fault
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.26 stable release
# gpg: Signature made Tue 10 Dec 2019 01:52:47 PM EST
# gpg: using RSA key EBCE84042C07D1D6
# gpg: Can't check signature: No public key
|
|
commit 84968291d7924261c6a0624b9a72f952398e258b upstream.
Add missing endianness conversion when setting the line speed so that
this driver might work also on big-endian machines.
Also use an unsigned format specifier in the corresponding debug
message.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1251dab9e0a2c4d0d2d48370ba5baa095a5e8774 upstream.
Fix a user-controlled slab buffer overflow due to a missing sanity check
on the bulk-out transfer buffer used for control requests.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d5501d5c29a2e684640507cfee428178d6fd82ca upstream.
It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;
xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62: expected unsigned int [usertype] field0
xhci-debugfs.c:205:62: got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62: expected unsigned int [usertype] field1
xhci-debugfs.c:206:62: got restricted __le32
...
[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bfa3dbb343f664573292afb9e44f9abeb81a19de upstream.
The arguments to queue_trb are always byteswapped to LE for placement in
the ring, but this should not happen in the case of immediate data; the
bytes copied out of transfer_buffer are already in the correct order.
Add a complementary byteswap so the bytes end up in the ring correctly.
This was observed on BE ppc64 with a "Texas Instruments TUSB73x0
SuperSpeed USB 3.0 xHCI Host Controller [104c:8241]" as a ch341
usb-serial adapter ("1a86:7523 QinHeng Electronics HL-340 USB-Serial
adapter") always transmitting the same character (generally NUL) over
the serial link regardless of the key pressed.
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 33e39350ebd2 ("usb: xhci: add Immediate Data Transfer support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 52403cfbc635d28195167618690595013776ebde upstream.
USB control-message timeouts are specified in milliseconds, not jiffies.
Waiting 83 minutes for a transfer to complete is a bit excessive.
Fixes: 2824bd250f0b ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Reported-by: syzbot+a4fbb3bb76cda0ea4e58@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022153127.22295-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d98ee2a19c3334e9343df3ce254b496f1fc428eb upstream.
The custom ring-buffer implementation was merged without any locking or
explicit memory barriers, but a spinlock was later added by commit
9d33efd9a791 ("USB: ldusb bugfix").
The lock did not cover the update of the tail index once the entry had
been processed, something which could lead to memory corruption on
weakly ordered architectures or due to compiler optimisations.
Specifically, a completion handler running on another CPU might observe
the incremented tail index and update the entry before ld_usb_read() is
done with it.
Fixes: 2824bd250f0b ("[PATCH] USB: add ldusb driver")
Fixes: 9d33efd9a791 ("USB: ldusb bugfix")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
virt_boundary_mask to avoid SG overflows")
commit 9a976949613132977098fc49510b46fa8678d864 upstream.
Commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG
overflows") attempted to solve a problem involving scatter-gather I/O
and USB/IP by setting the virt_boundary_mask for mass-storage devices.
However, it now turns out that this interacts badly with commit
09324d32d2a0 ("block: force an unlimited segment size on queues with a
virt boundary"), which was added later. A typical error message is:
ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)
There is no longer any reason to keep the virt_boundary_mask setting
for usb-storage. It was needed in the first place only for handling
devices with a block size smaller than the maxpacket size and where
the host controller was not capable of fully general scatter-gather
operation (that is, able to merge two SG segments into a single USB
packet). But:
High-speed or slower connections never use a bulk maxpacket
value larger than 512;
The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;
All the host controllers capable of SuperSpeed operation can
handle fully general SG;
Since commit ea44d190764b ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.
Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask. So in order to fix
the swiotlb problem, this patch reverts commit 747668dbc061.
Reported-and-tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Link: https://marc.info/?l=linux-usb&m=157134199501202&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Seth Bollinger <Seth.Bollinger@digi.com>
CC: <stable@vger.kernel.org>
Fixes: 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")
Acked-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910211145520.1673-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 54f83b8c8ea9b22082a496deadf90447a326954e upstream.
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that a UDC will
crash or hang when trying to handle a non-zero-length usb_request for
such an endpoint. Indeed, dummy-hcd gets a divide error when trying
to calculate the remainder of a transfer length by the maxpacket
value, as discovered by the syzbot fuzzer.
Currently the gadget core does not check for endpoints having a
maxpacket value of 0. This patch adds a check to usb_ep_enable(),
preventing such endpoints from being used.
As far as I know, none of the gadget drivers in the kernel tries to
create an endpoint with maxpacket = 0, but until now there has been
nothing to prevent userspace programs under gadgetfs or configfs from
doing it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8ab8bf161038a8768553@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281052370.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
segments")
commit 1186f86a71130a7635a20843e355bb880c7349b2 upstream.
Commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments"),
copying a similar commit for usb-storage, attempted to solve a problem
involving scatter-gather I/O and USB/IP by setting the
virt_boundary_mask for mass-storage devices.
However, it now turns out that the analogous change in usb-storage
interacted badly with commit 09324d32d2a0 ("block: force an unlimited
segment size on queues with a virt boundary"), which was added later.
A typical error message is:
ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)
There is no longer any reason to keep the virt_boundary_mask setting
in the uas driver. It was needed in the first place only for
handling devices with a block size smaller than the maxpacket size and
where the host controller was not capable of fully general
scatter-gather operation (that is, able to merge two SG segments into
a single USB packet). But:
High-speed or slower connections never use a bulk maxpacket
value larger than 512;
The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;
All the host controllers capable of SuperSpeed operation can
handle fully general SG;
Since commit ea44d190764b ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.
Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask. So in order to head
off potential problems similar to those affecting usb-storage, this
patch reverts commit 3ae62a42090f.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Fixes: 3ae62a42090f ("UAS: fix alignment of scatter/gather segments")
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.24 stable release
# gpg: Signature made Mon 25 Nov 2019 12:09:44 PM EST
# gpg: using RSA key EBCE84042C07D1D6
# gpg: Can't check signature: No public key
|
|
commit 7a6f22d7479b7a0b68eadd308a997dd64dda7dae upstream.
Fix broken read implementation, which could be used to trigger slab info
leaks.
The driver failed to check if the custom ring buffer was still empty
when waking up after having waited for more data. This would happen on
every interrupt-in completion, even if no data had been added to the
ring buffer (e.g. on disconnect events).
Due to missing sanity checks and uninitialised (kmalloced) ring-buffer
entries, this meant that huge slab info leaks could easily be triggered.
Note that the empty-buffer check after wakeup is enough to fix the info
leak on disconnect, but let's clear the buffer on allocation and add a
sanity check to read() to prevent further leaks.
Fixes: 2824bd250f0b ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Reported-by: syzbot+6fe95b826644f7f12b0b@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191018151955.25135-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b14a39048c1156cfee76228bf449852da2f14df8 upstream.
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
Fixes: 2824bd250f0b ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191010125835.27031-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6f1d1dc8d540a9aa6e39b9cb86d3a67bbc1c8d8d upstream.
Fix races between closing a port and opening or closing another port on
the same device which could lead to a failure to start or stop the
shared interrupt URB. The latter could potentially cause a
use-after-free or worse in the completion handler on driver unbind.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b987b66ac3a2bc2f7b03a0ba48a07dc553100c07 upstream.
It seems that the right variable to use in this case is *i*, instead of
*n*, otherwise there is an undefined behavior when right shifiting by more
than 31 bits when multiplying n by 8; notice that *n* can take values
equal or greater than 4 (4, 8, 16, ...).
Also, notice that under the current conditions (bl = 3), we are skiping
the handling of bytes 3, 7, 31... So, fix this by updating this logic
and limit *bl* up to 4 instead of up to 3.
This fix is based on function udc_stuff_fifo().
Addresses-Coverity-ID: 1454834 ("Bad bit shift operation")
Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20191014191830.GA10721@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b6c03e5f7b463efcafd1ce141bd5a8fc4e583ae2 upstream.
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191010125835.27031-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9bbfceea12a8f145097a27d7c7267af25893c060 upstream.
In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.
Fixes: 1a7b12f69a94 ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.22 stable release
# gpg: Signature made Sat 09 Nov 2019 08:56:23 PM EST
# gpg: using RSA key EBCE84042C07D1D6
# gpg: Can't check signature: No public key
|
|
commit 7a759197974894213621aa65f0571b51904733d6 upstream.
A recent commit addressing a runtime PM use-count regression, introduced
a use-after-free by not making sure we held a reference to the struct
usb_interface for the lifetime of the driver data.
Fixes: 9a31535859bf ("USB: usblp: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+cd24df4d075c319ebfc5@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191015175522.18490-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit fd47a417e75e2506eb3672ae569b1c87e3774155 upstream.
The problem is that sizeof() is unsigned long so negative error codes
are type promoted to high positive values and the condition becomes
false.
Fixes: 1d427be4a39d ("USB: legousbtower: fix slab info leak at probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191011141115.GA4521@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 726b55d0e22ca72c69c947af87785c830289ddbc upstream.
The driver was accessing its struct usb_device in its release()
callback without holding a reference. This would lead to a
use-after-free whenever the device was disconnected while the character
device was still open.
Fixes: fef526cae700 ("USB: legousbtower: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 0b074f6986751361ff442bc1127c1648567aa8d6 upstream.
The driver would return with a nonzero open count in case the reset
control request failed. This would prevent any further attempts to open
the char dev until the device was disconnected.
Fix this by incrementing the open count only on successful open.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit cd81e6fa8e033e7bcd59415b4a65672b4780030b upstream.
The driver is using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg and dev_err statements in the
completion handlers which relies on said pointer.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes: 9d974b2a06e3 ("USB: legousbtower.c: remove err() usage")
Fixes: fef526cae700 ("USB: legousbtower: remove custom debug macro")
Fixes: 4dae99638097 ("USB: legotower: remove custom debug macro and module parameter")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 33a7813219f208f4952ece60ee255fd983272dec upstream.
Fix a potential deadlock if disconnect races with open.
Since commit d4ead16f50f9 ("USB: prevent char device open/deregister
race") core holds an rw-semaphore while open is called and when
releasing the minor number during deregistration. This can lead to an
ABBA deadlock if a driver takes a lock in open which it also holds
during deregistration.
This effectively reverts commit 78663ecc344b ("USB: disconnect open race
in legousbtower") which needlessly introduced this issue after a generic
fix for this race had been added to core by commit d4ead16f50f9 ("USB:
prevent char device open/deregister race").
Fixes: 78663ecc344b ("USB: disconnect open race in legousbtower")
Cc: stable <stable@vger.kernel.org> # 2.6.24
Reported-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com
Tested-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1d427be4a39defadda6dd8f4659bc17f7591740f upstream.
Make sure to check for short transfers when retrieving the version
information at probe to avoid leaking uninitialised slab data when
logging it.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f2372b87c386871b16d7dbda680d98d4092ab708 upstream.
Making sure that ucsi_displayport_enter() function does not
return an error if the displayport alternate mode has
already been entered. It's normal that the firmware (or
controller) has already entered the alternate mode by the
time the operating system is notified about the device.
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191004100219.71152-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7101949f36fc77b530b73e4c6bd0066a2740d75b upstream.
The "port->typec_caps.data" and "port->typec_caps.type" variables are
enums and in this context GCC will treat them as an unsigned int so they
can never be less than zero.
Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191001120117.GA23528@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4d599cd3a097a85a5c68a2c82b9a48cddf9953ec upstream.
According to usb_ep_set_halt()'s description,
__usbhsg_ep_set_halt_wedge() should return -EAGAIN if the IN endpoint
has any queue or data. Otherwise, this driver is possible to cause
just STALL without sending a short packet data on g_mass_storage driver,
and then a few resetting a device happens on a host side during
a usb enumaration.
Fixes: 2f98382dcdfe ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|