| Age | Commit message (Collapse) | Author |
|---|
|
commit ed62ca2f4f51c17841ea39d98c0c409cb53a3e10 upstream.
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
[ 14.012445] BUG: spinlock bad magic on CPU#0, modprobe/2091
[ 14.012460] lock: 0xffffffc0cb055978, .magic: ffffffc0, .owner: cryption contexts: %lu/%lu
[ 14.012460] /1025536097, .owner_cpu: 0
[ 14.012466] CPU: 0 PID: 2091 Comm: modprobe Not tainted 4.4.79 #352
[ 14.012468] Hardware name: Google Kevin (DT)
[ 14.012471] Call trace:
[ 14.012483] [<....>] dump_backtrace+0x0/0x160
[ 14.012487] [<....>] show_stack+0x20/0x28
[ 14.012494] [<....>] dump_stack+0xb4/0xf0
[ 14.012500] [<....>] spin_dump+0x8c/0x98
[ 14.012504] [<....>] spin_bug+0x30/0x3c
[ 14.012508] [<....>] do_raw_spin_lock+0x40/0x164
[ 14.012515] [<....>] _raw_spin_lock_irqsave+0x64/0x74
[ 14.012521] [<....>] __wake_up+0x2c/0x60
[ 14.012528] [<....>] async_completed+0x2d0/0x300
[ 14.012534] [<....>] __usb_hcd_giveback_urb+0xc4/0x138
[ 14.012538] [<....>] usb_hcd_giveback_urb+0x54/0xf0
[ 14.012544] [<....>] xhci_irq+0x1314/0x1348
[ 14.012548] [<....>] usb_hcd_irq+0x40/0x50
[ 14.012553] [<....>] handle_irq_event_percpu+0x1b4/0x3f0
[ 14.012556] [<....>] handle_irq_event+0x4c/0x7c
[ 14.012561] [<....>] handle_fasteoi_irq+0x158/0x1c8
[ 14.012564] [<....>] generic_handle_irq+0x30/0x44
[ 14.012568] [<....>] __handle_domain_irq+0x90/0xbc
[ 14.012572] [<....>] gic_handle_irq+0xcc/0x18c
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 082df8be455ade361748f0385aa6c9c8d07be167 upstream.
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e1806 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5ded
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95463d ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5ded ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e1806 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6b422b88b46353cf596e0db6dc0e39d50d90d6e upstream.
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1279ef74eeeb5f627f091c71d80dd7ac766c99d upstream.
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 169e86546f5712179709de23cd64bbb15f199fab upstream.
This commit adds support (an ID, really) for D-Link DWM-157 hardware
version C1 USB modem to option driver.
According to manufacturer-provided Windows INF file the device has four
serial ports:
"D-Link HSPA+DataCard Diagnostics Interface" (interface 2; modem port),
"D-Link HSPA+DataCard NMEA Device" (interface 3),
"D-Link HSPA+DataCard Speech Port" (interface 4),
"D-Link HSPA+DataCard Debug Port" (interface 5).
usb-devices output:
T: Bus=05 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=7d0e Rev=03.00
S: Manufacturer=D-Link,Inc
S: Product=D-Link DWM-157
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de3af5bf259d7a0bfaac70441c8568ab5998d80c upstream.
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
BugLink: https://bugs.launchpad.net/bugs/1678477
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add new ATEN device id
usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
USB: Check for dropped connection before switching to full speed
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
USB: serial: option: add D-Link DWM-222 device ID
usb: musb: fix tx fifo flush handling again
usb: core: unlink urbs from the tail of the endpoint's urb_list
usb-storage: fix deadlock involving host lock and scsi_done
uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
USB: hcd: Mark secondary HCD as dead if the primary one died
USB: serial: cp210x: add support for Qivicon USB ZigBee dongle
|
|
This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: stable <stable@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.
The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.
Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure. This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.
The logic for doing this is careful to check that the device is still
connected. But this check is inadequate if the device disconnects and
reconnects before the check is done. The symptom is that a device
works, but much more slowly than it is capable of operating.
The situation was made worse recently by commit 22547c4cc4fe ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.
This patch makes the check more robust. If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume
On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.
In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.
As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.13-rc4
Here are some new device ids for v4.13-rc4.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.13-rc4
Another fix for isochronous transfers on dwc3. This time around, we're
making sure that we use correct PIDs in all transfer sizes.
MSM PHY driver got a fix for the use of devm_regulator_bulk_get() API
which will avoid kernel crashes.
Renesas DRD driver got 3 fixes: a fix on giveback, a fix for proper
controller programming and the removal of set-but-never-used variable.
|
|
The commit b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps
when the driver stops") causes the unused-but-set-variable warning.
But, if the usbhsg_ep_disable() will return non-zero value, udc/core.c
doesn't clear the ep->enabled flag. So, this driver should not return
non-zero value, if the pipe is zero because this means the pipe is
already disabled. Otherwise, the ep->enabled flag is never cleared
when the usbhsg_ep_disable() is called by the renesas_usbhs driver first.
Fixes: b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Fixes: 11432050f070 ("usb: renesas_usbhs: gadget: fix NULL pointer dereference in ep_disable()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit.
If the bit sets to 1, the VBUS drive is controlled by phy related
registers (called "UCOM Registers" on the manual). Since R-Car Gen3
environment will control VBUS by phy-rcar-gen3-usb2 driver,
the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes
the register's value. Otherwise, even if the ID pin indicates to
peripheral, the R-Car will output USBn_PWEN to 1 when a host driver
is running.
Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control"
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The regulator_bulk_data pointer passed to devm_regulator_bulk_get()
is used to store the client handles for the regulators, which
is later used by devm_regulator_bulk_release() to free the
regulators.
Passing a local array as is done here means the memory used to
store the handles is freed causing the handles to be corrupted,
resulting in a crash when devm_regulator_bulk_release() tries to
free them.
Fix this my moving the array inside of the msm_otg structure.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
According to the gadget.h, a "complete" function will always be called
with interrupts disabled. However, sometimes usb3_request_done() function
is called with interrupts enabled. So, this function should be held
by spin_lock_irqsave() to disable interruption. Also, this driver has
to call spin_unlock() to avoid spinlock recursion by this driver before
calling usb_gadget_giveback_request().
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The PIDs for Isochronous data transfers are incorrect
for high bandwidth IN endpoints when the request length
is less than EP wMaxPacketSize.
As per spec correct PIDs for ISOC data transfers are:
1) For request length <= maxpacket
- DATA0,
2) For maxpacket < length <= (2 * maxpacket)
- DATA1, DATA0
3) For (2 * maxpacket) < length <= (3 * maxpacket)
- DATA2, DATA1, DATA0.
But driver always sets PCM fields based on wMaxPacketSize
due to which DATA2 happens even for small requests.
Fix this by setting the PCM field of trb->size depending
on request length rather than fixing it to the value
depending on wMaxPacketSize.
Ideally it shouldn't give any issues as dwc3 will send
0-length packet for next IN token if host sends (even
after receiving a short packet). Windows seems to ignore
this but with MacOS frame loss observed when using f_uvc.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The Renesas uPD72020x XHCI controller seems to suffer from a really
annoying bug, where it may retain some of its DMA programming across a XHCI
reset, and despite the driver correctly programming new DMA addresses.
This is visible if the device has been using 64-bit DMA addresses, and is
then switched to using 32-bit DMA addresses. The top 32 bits of the
address (now zero) are ignored are replaced by the 32 bits from the
*previous* programming. Sticking with 64-bit DMA always works, but doesn't
seem very appropriate.
A PCI reset of the device restores the normal functionality, which is done
at probe time. Unfortunately, this has to be done before any quirk has
been discovered, hence the intrusive nature of the fix.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: stable@vger.kernel.org # v4.11+
|
|
Add device id for D-Link DWM-222.
Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
commit 68fe05e2a451 ("usb: musb: fix tx fifo flush handling") drops the
1ms delay trying to solve the long disconnect time issue when
application queued many tx urbs. However, the 1ms delay is needed for
some use cases, for example, without the delay, reconnecting AR9271 WIFI
dongle no longer works if the connection is dropped from the AP.
So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the
long disconnect time problem with a separate patch for
usb_hcd_flush_endpoint().
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While unlink an urb, if the urb has been programmed in the controller,
the controller driver might do some hw related actions to tear down the
urb.
Currently usb_hcd_flush_endpoint() passes each urb from the head of the
endpoint's urb_list to the controller driver, which could make the
controller driver think each urb has been programmed and take the
unnecessary actions for each urb.
This patch changes the behavior in usb_hcd_flush_endpoint() to pass the
urbs from the tail of the list, to avoid any unnecessary actions in an
controller driver.
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Christoph Hellwig says that since version 4.12, the kernel switched to
using blk-mq by default. The old code used a softirq for handling
request completions, but blk-mq can handle completions in the caller's
context. This may cause a problem for usb-storage, because it invokes
the ->scsi_done callback while holding the host lock, and the
completion routine sometimes tries to acquire the same lock (when
running the error handler, for example).
The consequence is that the existing code will sometimes deadlock upon
error completion of a SCSI command (with a lockdep warning).
This is easy enough to fix, since usb-storage doesn't really need to
hold the host lock while the callback runs. It was simpler to write
it that way, but moving the call outside the locked region is pretty
easy and there's no downside. That's what this patch does.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
CC: Christoph Hellwig <hch@lst.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Similar to commit d595259fbb7a ("usb-storage: Add ignore-residue quirk for
Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already
present in unusual_uas.h. Both in same controller IC family.
Issue is that MakeMKV fails during key exchange with installed bluray drive
with following error:
002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0'
Signed-off-by: Alan Swanson <reiver@improbability.net>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared
HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for
the primary one.
Among other thigs, this prevents check_root_hub_suspended() from
returning -EBUSY for dead HCDs which helps to work around system
suspend issues in some situations.
This actually fixes occasional suspend failures on one of my test
machines.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Found this issue by kmemleak.
xhci_run() did not check return val and free command for
xhci_queue_vendor_command()
unreferenced object 0xffff88011c0be500 (size 64):
comm "kworker/0:1", pid 58, jiffies 4294670908 (age 50.420s)
hex dump (first 32 bytes):
backtrace:
[<ffffffff8176166a>] kmemleak_alloc+0x4a/0xa0
[<ffffffff8121801a>] kmem_cache_alloc_trace+0xca/0x1d0
[<ffffffff81576bf4>] xhci_alloc_command+0x44/0x130
[<ffffffff8156f1cc>] xhci_run+0x4cc/0x630
[<ffffffff8153b84b>] usb_add_hcd+0x3bb/0x950
[<ffffffff8154eac8>] usb_hcd_pci_probe+0x188/0x500
[<ffffffff815851ac>] xhci_pci_probe+0x2c/0x220
[<ffffffff813d2ca5>] local_pci_probe+0x45/0xa0
[<ffffffff810a54e4>] work_for_cpu_fn+0x14/0x20
[<ffffffff810a8409>] process_one_work+0x149/0x360
[<ffffffff810a8d08>] worker_thread+0x1d8/0x3c0
[<ffffffff810ae7d9>] kthread+0x109/0x140
[<ffffffff8176d585>] ret_from_fork+0x25/0x30
[<ffffffffffffffff>] 0xffffffffffffffff
Cc: <stable@vger.kernel.org>
Signed-off-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
Cc: <stable@vger.kernel.org>
Fixes: 0f1d832ed1fb ("usb: xhci: Add port test modes support for usb2")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
[code simplification and reworded sidenote in commit message -Mathias]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Reported-by: rocko r <rockorequin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.13-rc2
First set of fixes for the current -rc cycle. Only three fixes on dwc3
this time around (proper order for getting a PHY reference, fix for
unmapping DMA and a fix for requesting IRQ on the OMAP glue layer).
Most fixes are on the renesas USB controller, fixing several old bugs
with most going to stable.
dwc2 also learned that it *must* reset USB Address to zero on Reset
interrupts.
Apart from these, some drivers needed HAS_DMA dependency and there's a
sparse warning fix for bdc udc.
|
|
A gadget driver will not disable eps immediately when ->disconnect()
is called. But, since this driver assumes all eps stop after
the ->disconnect(), unexpected behavior happens (especially in system
suspend).
So, this patch disables all eps in usbhsg_try_stop(). After disabling
eps by renesas_usbhs driver, since some functions will be called by
both a gadget and renesas_usbhs driver, renesas_usbhs driver should
protect uep->pipe. To protect uep->pipe easily, this patch adds a new
lock in struct usbhsg_uep.
Fixes: 2f98382dc ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that some registers may be not initialized
after resume if the USBHSF_RUNTIME_PWCTRL is not set. Otherwise,
if a cable is not connected, the driver will not enable INTENB0.VBSE
after resume. And then, the driver cannot detect the VBUS.
Fixes: ca8a282a5373 ("usb: gadget: renesas_usbhs: add suspend/resume support")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that unexpected behavior happens when
both the interrupt handler and renesas_usb3_ep_enable() are called.
In this case, since usb3_start_pipen() checked the usb3_ep->started,
but the flags was not protected. So, this patch protects the flag
by usb3->lock. Since renesas_usb3_ep_enable() for EP0 will be not called,
this patch doesn't take care of usb3_start_pipe0().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dedicated dmac can transfer a zero-length-packet (zlp) if some bits
of the USB_COM_CON register. However, the commit 2d4aa21a73ba ("usb:
gadget: udc: renesas_usb3: add support for dedicated DMAC") didn't set
the bits to 1. So, this patch fixes it.
Fixes: 2d4aa21a73b ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The commit 2d4aa21a73ba ("usb: gadget: udc: renesas_usb3: add support
for dedicated DMAC") has a bug in the renesas_usb3_dma_free_prd().
The size of dma_free_coherent() should be the same with dma_alloc_coherent()
Otherwise, this code causes a WARNING by mm/page_alloc.c when
renesas_usb3_dma_free_prd() is called. So, this patch fixes it.
Fixes: 2d4aa21a73ba ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
As per USB spec, multiple-bytes fields are stored
in little-endian order. Use CPU<->LE helpers for
such fields.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
As per USB spec, multiple-bytes fields are stored
in little-endian order. Use CPU<->LE helpers for
such fields.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fixes the following Sparse warnings:
>> drivers/usb/gadget/udc/snps_udc_plat.c:31:6: sparse: symbol 'start_udc' was not declared. Should it be static?
>> drivers/usb/gadget/udc/snps_udc_plat.c:41:6: sparse: symbol 'stop_udc' was not declared. Should it be static?
>> drivers/usb/gadget/udc/snps_udc_plat.c:79:6: sparse: symbol 'udc_drd_work' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Reseted DEVADDR field in DCFG to zero on USB RESET.
Device address in DCFG register does not reset to zero,
which required to pass enumeration, after disconnect and
reconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When us->extra is null the driver is not initialized, however, a
later call to osd200_scsi_to_ata is made that dereferences
us->extra, causing a null pointer dereference. The code
currently detects and reports that the driver is not initialized;
add a return to avoid the subsequent dereference issue in this
check.
Thanks to Alan Stern for pointing out that srb->result needs setting
to DID_ERROR << 16
Detected by CoverityScan, CID#100308 ("Dereference after null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new driver causes a build failure in some configurations:
In file included from /git/arm-soc/drivers/usb/typec/ucsi/trace.h:9:0,
from /git/arm-soc/drivers/usb/typec/ucsi/trace.c:2:
drivers/usb/typec/ucsi/ucsi.h:331:39: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
This includes the required header file.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add device-id entry for DATECS FP-2000 fiscal printer needing the
NO_UNION_NORMAL quirk.
Reported-by: Anton Avramov <lukav@lukav.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The German Telekom offers a ZigBee USB Stick under the brand name Qivicon
for their SmartHome Home Base in its 1. Generation. The productId is not
known by the according kernel module, this patch adds support for it.
Signed-off-by: Stefan Triller <github@stefantriller.de>
Reviewed-by: Frans Klaver <fransklaver@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
A recent optimization was made so that a request put on the
pending_list wouldn't get mapped for DMA until just before
preparing a TRB for it. However, this poses a problem in case
the request is dequeued or the endpoint is disabled before the
mapping is done as that would lead to dwc3_gadget_giveback()
unconditionally calling usb_gadget_unmap_request_for_dev() with
an invalid request->dma handle. Depending on the platform's DMA
implementation the unmap operation could result in a panic.
Since we know a successful mapping is a prerequisite for getting
a TRB, the unmap can be conditionally called only when req->trb
is non-NULL.
Fixes: cdb55b39fab8 ("usb: dwc3: gadget: lazily map requests for DMA")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If NO_DMA=y:
ERROR: "usb_gadget_map_request" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_destroy" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "usb_gadget_unmap_request" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
As USB_SNP_CORE is selected by USB_SNP_UDC_PLAT and USB_AMD5536UDC,
these should depend on HAS_DMA, too. For USB_AMD5536UDC, this is
already fulfilled through the dependency on USB_PCI (PCI implies
HAS_DMA).
Add dependencies on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If NO_DMA=y:
ERROR: "usb_gadget_map_request" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!
ERROR: "usb_gadget_unmap_request" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
It is wrong to do --i in the for loop.
Fixes: dd02ea5a3305 ("usb: gadget: mass_storage: Use static array for luns")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
IRQ_NOAUTOEN cannot be used with shared IRQs, since commit 04c848d39879
("genirq: Warn when IRQ_NOAUTOEN is used with shared interrupts") and
kernel now throws a warn dump. But OMAP DWC3 driver uses this flag. As
per commit 12a7f17fac5b ("usb: dwc3: omap: fix race of pm runtime with
irq handler in probe") that introduced this flag, PM runtime can race
with IRQ handler when deferred probing happens due to extcon,
therefore IRQ_NOAUTOEN needs to be set so that irq is not enabled until
extcon is registered.
Remove setting of IRQ_NOAUTOEN and move the registration of
shared irq to a point after dwc3_omap_extcon_register() and
of_platform_populate(). This avoids possibility of probe deferring and
above said race condition.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
Douglas Anderson
Johan Hovold
Sandeep Singh
Dmitry Fleytman
Maciej S. Szmigiero
Kai-Heng Feng
Linus Torvalds
Greg Kroah-Hartman
Alan Stern
Yoshihiro Shimoda
Rajendra Nayak
Manu Gautam
Marc Zyngier
Hector Martin
Bin Liu
Alan Swanson
Rafael J. Wysocki
Shu Wang
Peter Chen
Mathias Nyman
Shyam Sundar S K
Jiahau Chang
Ruslan Bilovol
kbuild test robot
Minas Harutyunyan
Colin Ian King
Arnd Bergmann
Stefan Triller
Jack Pham
Geert Uytterhoeven
Axel Lin
Vignesh R