| Age | Commit message (Collapse) | Author |
|---|
|
commit b791a67f68121d69108640d4a3e591d210ffe850 upstream.
The function ucsi_displayport_work() does not access the
connector, so it also must not acquire the connector lock.
This fixes a potential deadlock scenario:
ucsi_displayport_work() -> lock(&con->lock)
typec_altmode_vdm()
dp_altmode_vdm()
dp_altmode_work()
typec_altmode_enter()
ucsi_displayport_enter() -> lock(&con->lock)
Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240507134316.161999-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8774ea7a553e2aec323170d49365b59af0a2b7e0 ]
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5962ded777d689cd8bf04454273e32228d7fb71f upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released is a plug evaluates
against the released altmode's partner instead of the calling altmode, so
change adev in typec_altmode_put_partner to properly refer to the altmode
being released.
Because typec_altmode_set_partner calls get_device() on the port altmode,
add partner_adev that points to the port altmode in typec_put_partner to
call put_device() on. typec_altmode_set_partner is not called for port
altmodes, so add a check in typec_altmode_release to prevent
typec_altmode_put_partner() calls on port altmode release.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: <stable@vger.kernel.org>
Co-developed-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Tested-by: Christian A. Ehrhardt <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240103181754.2492492-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c6b789e954fae73c548f39332bcc56bdf0d4373 upstream.
This reverts commit b17b7fe6dd5c6ff74b38b0758ca799cdbb79e26e.
That commit messed up the reference counting, so it needs to
be rethought.
Fixes: b17b7fe6dd5c ("usb: typec: class: fix typec_altmode_put_partner to put plugs")
Cc: <stable@vger.kernel.org>
Cc: RD Babiera <rdbabiera@google.com>
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Closes: https://lore.kernel.org/lkml/CAP-bSRb3SXpgo_BEdqZB-p1K5625fMegRZ17ZkPE1J8ZYgEHDg@mail.gmail.com/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240102091142.2136472-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b17b7fe6dd5c6ff74b38b0758ca799cdbb79e26e upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released evaluates against the
released altmode's partner instead of the calling altmode itself, so change
adev in typec_altmode_put_partner to properly refer to the altmode being
released.
typec_altmode_set_partner is not run for port altmodes, so also add a check
in typec_altmode_release to prevent typec_altmode_put_partner() calls on
port altmode release.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231129192349.1773623-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f23643306430f86e2f413ee2b986e0773e79da31 ]
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 95b4d51c96a87cd760c2a4f27fb28a59a27b6368 ]
Refactor tcpm_handle_vdm_request and its tcpm_pd_svdm helper function so
that reporting the results of the vdm to the altmode-driver is separated
out into a clear separate step inside tcpm_handle_vdm_request, instead
of being scattered over various places inside the tcpm_pd_svdm helper.
This is a preparation patch for fixing an AB BA lock inversion between the
tcpm code and some altmode drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f23643306430 ("usb: typec: bus: verify partner exists in typec_altmode_attention")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8afe9a3548f9d1805dcea6d97978f2179c8403a3 ]
Refactor the tcpm_handle_vdm_request payload handling by doing the
endianness conversion only once directly inside tcpm_handle_vdm_request
itself instead of doing it multiple times inside various helper functions
called by tcpm_handle_vdm_request.
This is a preparation patch for some further refactoring to fix an AB BA
lock inversion between the tcpm code and some altmode drivers.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f23643306430 ("usb: typec: bus: verify partner exists in typec_altmode_attention")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 23e60c8daf5ec2ab1b731310761b668745fcf6ed ]
According the "USB Type-C Port Controller Interface Specification v2.0"
the TCPC sets the fault status register bit-7
(AllRegistersResetToDefault) once the registers have been reset to
their default values.
This triggers an alert(-irq) on PTN5110 devices albeit we do mask the
fault-irq, which may cause a kernel hang. Fix this generically by writing
a one to the corresponding bit-7.
Cc: stable@vger.kernel.org
Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Reported-by: "Angus Ainslie (Purism)" <angus@akkea.ca>
Closes: https://lore.kernel.org/all/20190508002749.14816-2-angus@akkea.ca/
Reported-by: Christian Bach <christian.bach@scs.ch>
Closes: https://lore.kernel.org/regressions/ZR0P278MB07737E5F1D48632897D51AC3EB329@ZR0P278MB0773.CHEP278.PROD.OUTLOOK.COM/t/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230816172502.1155079-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d8f28269dd4bf9b55c3fb376ae31512730a96fce upstream.
This patch fixes negative indexing of buf array in pin_assignment_show
when get_current_pin_assignments returns 0 i.e. no compatible pin
assignments are found.
BUG: KASAN: use-after-free in pin_assignment_show+0x26c/0x33c
...
Call trace:
dump_backtrace+0x110/0x204
dump_stack_lvl+0x84/0xbc
print_report+0x358/0x974
kasan_report+0x9c/0xfc
__do_kernel_fault+0xd4/0x2d4
do_bad_area+0x48/0x168
do_tag_check_fault+0x24/0x38
do_mem_abort+0x6c/0x14c
el1_abort+0x44/0x68
el1h_64_sync_handler+0x64/0xa4
el1h_64_sync+0x78/0x7c
pin_assignment_show+0x26c/0x33c
dev_attr_show+0x50/0xc0
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230508214443.893436-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dac3b192107b978198e89ec0f77375738352e0c8 ]
PD3.0 Spec 6.4.4.3.2 say that only Responder supports 12 or more SVIDs,
the Discover SVIDs Command Shall be executed multiple times until a
Discover SVIDs VDO is returned ending either with a SVID value of
0x0000 in the last part of the last VDO or with a VDO containing two
SVIDs with values of 0x0000.
In the current implementation, if the last VDO does not find that the
Discover SVIDs Command would be executed multiple times even if the
Responder SVIDs are less than 12, and we found some odd dockers just
meet this case. So fix it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20230316081149.24519-1-frank.wang@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit eddebe39602efe631b83ff8d03f26eba12cfd760 upstream.
While determining the initial pin assignment to be sent in the configure
message, using the DP_PIN_ASSIGN_DP_ONLY_MASK mask causes the DFP_U to
send both Pin Assignment C and E when both are supported by the DFP_U and
UFP_U. The spec (Table 5-7 DFP_U Pin Assignment Selection Mandates,
VESA DisplayPort Alt Mode Standard v2.0) indicates that the DFP_U never
selects Pin Assignment E when Pin Assignment C is offered.
Update the DP_PIN_ASSIGN_DP_ONLY_MASK conditional to intially select only
Pin Assignment C if it is available.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230329215159.2046932-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54e5c00a4eb0a4c663445b245f641bbfab142430 upstream.
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9682b41e52cc9f42f5c33caf410464392adaef04 upstream.
Commit c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin
assignment for UFP receptacles") fixed the pin assignment calculation
to take into account whether the peripheral was a plug or a receptacle.
But the "pin_assignments" sysfs logic was not updated. Address this by
using the macros introduced in the aforementioned commit in the sysfs
logic too.
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111020546.3384569-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 582836e3cfab4faafbdc93bbec96fce036a08ee1 upstream.
The code to extract a peripheral's currently supported Pin Assignments
is repeated in a couple of locations. Factor it out into a separate
function.
This will also make it easier to add fixes (we only need to update 1
location instead of 2).
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111020546.3384569-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0384e87e3fec735e47f1c133c796f32ef7a72a9b ]
I got the following report while doing device(mt6370-tcpc) load
test with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@34/tcpc/connector
The 'fwnode' set in tcpci_parse_config() which is called
in tcpci_register_port(), its node refcount is increased
in device_get_named_child_node(). It needs be put while
exiting, so call fwnode_handle_put() in the error path of
tcpci_register_port() and in tcpci_unregister_port() to
avoid leak.
Fixes: 5e85a04c8c0d ("usb: typec: add fwnode to tcpc")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221121062416.1026192-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6ddd180e3d9f92c1e482b3cdeec7dda086b1341 ]
typec_altmode_exit checks if ops->enter is not NULL but then calls
ops->exit a few lines below. Fix that and check for the function
pointer it's about to call instead.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114165924.33487-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c1e5c2f0cb8a22ec2e14af92afc7006491bebabb upstream.
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fb9e1d94789e8ee5a258a23bc588693f743fd6c upstream.
System like Android allow user control power role from UI, it is possible
to implement application base on typec uevent to refresh UI, but found
there is chance that UI show different state from typec attribute file.
In typec_set_pwr_opmode(), when partner support PD, there is no uevent
send to user space which cause the problem.
Fix it by sending uevent notification when change power mode to PD.
Fixes: bdecb33af34f ("usb: typec: API for controlling USB Type-C Multiplexers")
Cc: stable@vger.kernel.org
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1656662934-10226-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbc126ae381cf0a27822c1f822d0aeed74cc40d9 upstream.
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
In this case the remove callback even returns early without stopping the
tcpm worker thread and various timers. A work scheduled on the work
queue, or a firing timer after tcpci_remove() returned probably results
in a use-after-free situation because the regmap and driver data were
freed. So better make sure that tcpci_unregister_port() is called even
if disabling the irq failed.
Also emit a more specific error message instead of the i2c core's
"remove failed (EIO), will be ignored" and return 0 to suppress the
core's warning.
This patch is (also) a preparation for making i2c remove callbacks
return void.
Fixes: 3ba76256fc4e ("usb: typec: tcpci: mask event interrupts when remove driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220502080456.21568-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb5d7ff3cf0d55093c619b5ad107cd5c05ce8134 upstream.
All attempts to swap the roles timed out because the
completion was done without releasing the port lock. Fixing
that by releasing the lock before starting to wait for the
completion.
Link: https://lore.kernel.org/linux-usb/037de7ac-e210-bdf5-ec7a-8c0c88a0be20@gmail.com/
Fixes: ad74b8649bea ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220405134824.68067-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 825911492eb15bf8bb7fb94bc0c0421fe7a6327d upstream.
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90b8aa9f5b09edae6928c0561f933fec9f7a9987 upstream.
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbcd13df1e78eb2ba83a3c160eefe2d6f574beaf upstream.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
This change makes TCPM to wait in SNK_DEBOUNCED state until
CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously,
TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON.
This causes TCPM to loop continuously when connected to a
faulty power source that does not present vbus. Waiting in
SNK_DEBOUNCED also ensures that TCPM is adherant to
"4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements.
[ 6169.280751] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 6169.280759] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS]
[ 6169.280771] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS]
[ 6169.282427] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected]
[ 6169.450825] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 6169.450834] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS]
[ 6169.930892] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms]
[ 6169.931296] disable vbus discharge ret:0
[ 6169.931301] Setting usb_comm capable false
[ 6169.932783] Setting voltage/current limit 0 mV 0 mA
[ 6169.932802] polarity 0
[ 6169.933706] Requesting mux state 0, usb-role 0, orientation 0
[ 6169.936689] cc:=0
[ 6169.936812] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS]
[ 6169.937157] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 6170.036880] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 6170.036890] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev2 NONE_AMS]
[ 6170.036896] Start toggling
[ 6170.041412] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 6170.042973] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 6170.042976] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS]
[ 6170.042981] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS]
[ 6170.213014] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 6170.213019] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS]
[ 6170.693068] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms]
[ 6170.693304] disable vbus discharge ret:0
[ 6170.693308] Setting usb_comm capable false
[ 6170.695193] Setting voltage/current limit 0 mV 0 mA
[ 6170.695210] polarity 0
[ 6170.695990] Requesting mux state 0, usb-role 0, orientation 0
[ 6170.701896] cc:=0
[ 6170.702181] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS]
[ 6170.703343] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected]
Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20211130001825.3142830-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 362468830dd5bea8bf6ad5203b2ea61f8a4e8288 upstream.
The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc
wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate
bit in the mask register. In fact, interrupts are enabled when the mask
is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects
BC_LVL interrupt to be enabled.
This causes inability of the driver to recognize cable unplug events
in host mode (unplug is recognized only via a COMP_CHNG interrupt).
In device mode this bug was masked by simultaneous triggering of the VBUS
change interrupt, because of loss of VBUS when the port peer is providing
power.
Fixes: 48242e30532b ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"")
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b7a0a63f3fed57d413bb857de164ea9c3984bc4e ]
Calling tps6598x_block_read with a higher than allowed len can be
handled by just returning an error. There's no need to crash systems
with panic-on-warn enabled.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210914140235.65955-3-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6d91017a295e9790eec02c4e43f020cdb55f5d98 upstream.
TCPM for DRP should do the same action as SRC_ATTACHED when cc changes in
SRC_STARTUP state. Otherwise, TCPM will transition to SRC_UNATTACHED state
which is not satisfied with the Type-C spec.
Per Type-C spec:
DRP port should move to Unattached.SNK instead of Unattached.SRC if sink
removed.
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20210928111639.3854174-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03026197bb657d784220b040c6173267a0375741 upstream.
typec_register_altmode() misses to call altmode_id_remove() in an error
path. Add the missed function call to fix it.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20210617073226.47599-1-jingxiangfeng@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 142d0b24c1b17139f1aaaacae7542a38aa85640f upstream.
Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.
The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.
Fixes: 3370db35193b ("usb: typec: Registering real device entries for the muxes")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f247f0a82a4f8c3bfed178d8fd9e069d1424ee4e upstream.
If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful. Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.
Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d5ab95da2a41567440097c277c5771ad13928dad upstream.
As LKP noticed the Sparse is not happy about strict type handling:
.../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header
.../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header
Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.
Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together")
Fixes: 3c4fb9f16921 ("usb: typec: wcove: start using tcpm for USB PD support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 374157ff88ae1a7f7927331cbc72c1ec11994e8a upstream.
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a072022487 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 19c234a14eafca78e0bc14ffb8be3891096ce147 ]
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A
If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A
Fixes: 74e656d6b0551 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4050f2683f2c3151dc3dd1501ac88c57caf810ff upstream.
power_supply_changed needs to be called to notify clients
after the partner accepts the requested values for the pps
case.
Also, remove the redundant power_supply_changed at the end
of the tcpm_reset_port as power_supply_changed is already
called right after usb_type is changed.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3a0720224873587954b55d193d5b4abb14f0443 upstream.
tcpm_pd_select_pps_apdo overwrites port->pps_data.min_volt,
port->pps_data.max_volt, port->pps_data.max_curr even before
port partner accepts the requests. This leaves incorrect values
in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values in req_min_volt, req_max_volt, req_max_curr, req_out_volt,
req_op_curr. min_volt, max_volt, max_curr gets updated once the
partner accepts the request. current_limit, supply_voltage gets updated
once local port's tcpm enters SNK_TRANSITION_SINK when the accepted
current_limit and supply_voltage is enforced.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3dedafb8263ca4791a92a23f5230068f5bde008 upstream.
tcpm_pd_build_request overwrites current_limit and supply_voltage
even before port partner accepts the requests. This leaves stale
values in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values of current limit/supply voltage in req_current_limit
and req_supply_voltage. current_limit/supply_voltage gets updated
once the port partner accepts the request.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 86629e098a077922438efa98dc80917604dfd317 upstream.
tcpm-source-psy- does not invoke power_supply_changed API when
one of the published power supply properties is changed.
power_supply_changed needs to be called to notify
userspace clients(uevents) and kernel clients.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210317181249.1062995-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 41952a66015466c3208aac96b14ffd92e0943589 ]
The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2d9c6442a9c81f4f8dee678d0b3c183173ab1e2d upstream.
Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.
ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]
this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tSwapSourceStart
[ Upstream commit 6bbe2a90a0bb4af8dd99c3565e907fe9b5e7fd88 ]
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 386e15a650447f53de3d2d8819ce9393f31650a4 upstream.
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.
If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.
This fixes NULL pointer dereference that is caused by the
overrun.
Fixes: ad74b8649beaf ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo <zwanem@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f3546ff3f0a1000971daef58406954bad3f7061 upstream.
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 302c570bf36e997d55ad0d60628a2feec76954a4 upstream.
John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().
[1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org
Fixes: ce08eaeb6388 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@vger.kernel.org> # v4.18+
Cc: John Stultz <john.stultz@linaro.org>
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20200604112118.38062-1-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
invalid pointer
commit 0df9433fcae02215c8fd79690c134d535c7bb905 upstream.
Before this commit, typec_altmode_get_partner would return a
const struct typec_altmode * pointing to address 0x08 when
to_altmode(adev)->partner was NULL.
Add a check for to_altmode(adev)->partner being NULL to fix this.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206365
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1785972
Fixes: 5f54a85db5df ("usb: typec: Make sure an alt mode exist before getting its partner")
Cc: stable@vger.kernel.org
Signed-off-by: Naoki Kiryu <naonaokiryu2@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200422144345.43262-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 901789745a053286e0ced37960d44fa60267b940 upstream.
After PORT_RESET, the port is set to the appropriate
default_state. Ignore processing CC changes here as this
could cause the port to be switched into sink states
by default.
echo source > /sys/class/typec/port0/port_type
Before:
[ 154.528547] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms
[ 154.528560] CC1: 0 -> 0, CC2: 3 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 154.528564] state change PORT_RESET -> SNK_UNATTACHED
After:
[ 151.068814] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[ 151.072440] CC1: 3 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 151.172117] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 151.172136] pending state change PORT_RESET_WAIT_OFF -> SRC_UNATTACHED @ 870 ms [rev3 NONE_AMS]
[ 152.060106] state change PORT_RESET_WAIT_OFF -> SRC_UNATTACHED [delayed 870 ms]
[ 152.060118] Start toggling
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200402215947.176577-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 081da1325d351ea8804cf74e65263ea120834f33 upstream.
Locking the connector in ucsi_register_displayport() to make
sure that nothing can access the displayport alternate mode
before the function has finished and the alternate mode is
actually ready.
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200311130006.41288-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d16e7b62c5adcd13832c6b0ba364c3468d21b856 upstream.
If the registration of the DisplayPort was not successful,
or if the port does not support DisplayPort alt mode in the
first place, the function ucsi_displayport_remove_partner()
will fail with NULL pointer dereference when it attempts to
access the driver data.
Adding a check to the function to make sure there really is
driver data for the device before modifying it.
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Reported-by: Andrea Gagliardi La Gala <andrea.lagala@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206365
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200311130006.41288-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ba76256fc4e2a0d7fb26cc95459041ea0e88972 upstream.
This is to prevent any possible events generated while unregister
tpcm port.
Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1579502333-4145-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb7a3bb8c955b3694e0e0998413ce1563c02f90c upstream.
commit 8f6244055bd3 ("usb: typec: fusb302: Always provide fwnode for the
port") didn't convert this value from mW to uW when migrating to a new
specification format like it should have.
Fixes: 8f6244055bd3 ("usb: typec: fusb302: Always provide fwnode for the port")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/0da564559af75ec829c6c7e3aa4024f857c91bee.1579529334.git.tommyhebb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0e64350bf4668d0fbbfec66fd8e637b971b4e976 upstream.
commit 4c912bff46cc ("usb: typec: wcove: Provide fwnode for the port")
didn't convert this value from mW to uW when migrating to a new
specification format like it should have.
Fixes: 4c912bff46cc ("usb: typec: wcove: Provide fwnode for the port")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/d8be32512efd31995ad7d65b27df9d443131b07c.1579529334.git.tommyhebb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Heikki Krogerus
Marco Felsch
RD Babiera
Hans de Goede
Badhri Jagan Sridharan
Frank Wang
Prashant Malani
Yang Yingliang
Sven Peter
Pablo Sun
Linyu Yuan
Uwe Kleine-König
Sing-Han Chen
Ondrej Jirman
Xu Yang
Jing Xiangfeng
Bjorn Andersson
Mayank Rana
Andy Shevchenko
Peter Robinson
Li Jun
Naoki Kiryu
Thomas Hebb