| Age | Commit message (Collapse) | Author |
|---|
|
commit 3061b6491f491197a35e14e49f805d661b02acd4 upstream.
For ARM processor, unaligned access to device memory is not allowed.
Method memcpy does not take care of alignment.
USB detection failure with the unalingned address of memory, with
below kernel crash. To fix the unalingned address kernel panic,
replace memcpy with memcpy_toio method.
Kernel crash:
Unable to handle kernel paging request at virtual address ffff80000c05008a
Mem abort info:
ESR = 0x96000061
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
Data abort info:
ISV = 0, ISS = 0x00000061
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000000143b000
[ffff80000c05008a] pgd=100000087ffff003, p4d=100000087ffff003,
pud=100000087fffe003, pmd=1000000800bcc003, pte=00680000a0010713
Internal error: Oops: 96000061 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.19-xilinx-v2022.1 #1
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x30/0x260
lr : __xudc_ep0_queue+0xf0/0x110
sp : ffff800008003d00
x29: ffff800008003d00 x28: ffff800009474e80 x27: 00000000000000a0
x26: 0000000000000100 x25: 0000000000000012 x24: ffff000800bc8080
x23: 0000000000000001 x22: 0000000000000012 x21: ffff000800bc8080
x20: 0000000000000012 x19: ffff000800bc8080 x18: 0000000000000000
x17: ffff800876482000 x16: ffff800008004000 x15: 0000000000004000
x14: 00001f09785d0400 x13: 0103020101005567 x12: 0781400000000200
x11: 00000000c5672a10 x10: 00000000000008d0 x9 : ffff800009463cf0
x8 : ffff8000094757b0 x7 : 0201010055670781 x6 : 4000000002000112
x5 : ffff80000c05009a x4 : ffff000800a15012 x3 : ffff00080362ad80
x2 : 0000000000000012 x1 : ffff000800a15000 x0 : ffff80000c050088
Call trace:
__memcpy+0x30/0x260
xudc_ep0_queue+0x3c/0x60
usb_ep_queue+0x38/0x44
composite_ep0_queue.constprop.0+0x2c/0xc0
composite_setup+0x8d0/0x185c
configfs_composite_setup+0x74/0xb0
xudc_irq+0x570/0xa40
__handle_irq_event_percpu+0x58/0x170
handle_irq_event+0x60/0x120
handle_fasteoi_irq+0xc0/0x220
handle_domain_irq+0x60/0x90
gic_handle_irq+0x74/0xa0
call_on_irq_stack+0x2c/0x60
do_interrupt_handler+0x54/0x60
el1_interrupt+0x30/0x50
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x78/0x7c
arch_cpu_idle+0x18/0x2c
do_idle+0xdc/0x15c
cpu_startup_entry+0x28/0x60
rest_init+0xc8/0xe0
arch_call_rest_init+0x10/0x1c
start_kernel+0x694/0x6d4
__primary_switched+0xa4/0xac
Fixes: 1f7c51660034 ("usb: gadget: Add xilinx usb2 device support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/all/202209020044.CX2PfZzM-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230929121514.13475-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce9daa2efc0872a9a68ea51dc8000df05893ef2e ]
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20230628081511.186850-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 016da9c65fec9f0e78c4909ed9a0f2d567af6775 ]
The "udc" pointer was never set in the probe() function so it will
lead to a NULL dereference in udc_pci_remove() when we do:
usb_del_gadget_udc(&udc->gadget);
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZG+A/dNpFWAlCChk@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
renesas_usb3_remove due to race condition
[ Upstream commit 2b947f8769be8b8181dc795fd292d3e7120f5204 ]
In renesas_usb3_probe, role_work is bound with renesas_usb3_role_work.
renesas_usb3_start will be called to start the work.
If we remove the driver which will call usbhs_remove, there may be
an unfinished work. The possible sequence is as follows:
CPU0 CPU1
renesas_usb3_role_work
renesas_usb3_remove
usb_role_switch_unregister
device_unregister
kfree(sw)
//free usb3->role_sw
usb_role_switch_set_role
//use usb3->role_sw
The usb3->role_sw could be freed under such circumstance and then
used in usb_role_switch_set_role.
This bug was found by static analysis. And note that removing a
driver is a root-only operation, and should never happen in normal
case. But the root user may directly remove the device which
will also trigger the remove function.
Fix it by canceling the work before cleanup in the renesas_usb3_remove.
Fixes: 39facfa01c9f ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230320062931.505170-1-zyytlz.wz@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46ed6026ca2181c917c8334a82e3eaf40a6234dd ]
The code in the FOTG210 driver isn't entirely endianness-agnostic
as reported by the kernel robot sparse testing. This came to
the surface while moving the files around.
The driver is only used on little-endian systems, so this causes
no real-world regression, but it is nice to be strict and have
some compile coverage also on big endian machines, so fix it
up with the right LE accessors.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-usb/202211110910.0dJ7nZCn-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221111090317.94228-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fb8f60dd1b67520e0e0d7978ef17d015690acfc1 upstream.
When port is connected and then disconnected, the state stays as
configured. Which is incorrect as the port is no longer configured,
but in a not attached state.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/1664997235-18198-1-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8097cf2fb3b2205257f1c76f4808e3398d66b6d9 ]
USB_AMD5536UDC should depend on HAS_DMA since it selects USB_SNP_CORE,
which depends on HAS_DMA and since 'select' does not follow any
dependency chains.
Fixes this kconfig warning:
WARNING: unmet direct dependencies detected for USB_SNP_CORE
Depends on [n]: USB_SUPPORT [=y] && USB_GADGET [=y] && (USB_AMD5536UDC [=y] || USB_SNP_UDC_PLAT [=n]) && HAS_DMA [=n]
Selected by [y]:
- USB_AMD5536UDC [=y] && USB_SUPPORT [=y] && USB_GADGET [=y] && USB_PCI [=y]
Fixes: 97b3ffa233b9 ("usb: gadget: udc: amd5536: split core and PCI layer")
Cc: Raviteja Garimella <raviteja.garimella@broadcom.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220709013601.7536-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4757c9ade34178b351580133771f510b5ffcf9c8 upstream.
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220603140246.64529-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16b1941eac2bd499f065a6739a40ce0011a3d740 upstream.
The syzbot fuzzer found a use-after-free bug:
BUG: KASAN: use-after-free in dev_uevent+0x712/0x780 drivers/base/core.c:2320
Read of size 8 at addr ffff88802b934098 by task udevd/3689
CPU: 2 PID: 3689 Comm: udevd Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
dev_uevent+0x712/0x780 drivers/base/core.c:2320
uevent_show+0x1b8/0x380 drivers/base/core.c:2391
dev_attr_show+0x4b/0x90 drivers/base/core.c:2094
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
Fixes: 2ccea03a8f7e ("usb: gadget: introduce UDC Class")
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+348b571beb5eeb70a582@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiQgukfFFbBnwJ/9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f14c7227f342d9932f9b918893c8814f86d2a0d upstream.
Assure that host may not manipulate the index to point
past endpoint array.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0548b26901f082684ad1fb3ba397d2de3a1406a upstream.
On 64-bit:
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027080849.3276289-1-geert@linux-m68k.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17956b53ebff6a490baf580a836cbd3eae94892b upstream.
This loop is supposed to loop until if reads something other than
CS_IDST or until it times out after 30,000 attempts. But because of
the || vs && bug, it will never time out and instead it will loop a
minimum of 30,000 times.
This bug is quite old but the code is only used in USB_DEVICE_TEST_MODE
so it probably doesn't affect regular usage.
Fixes: 96fe53ef5498 ("usb: gadget: r8a66597-udc: add support for TEST_MODE")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210906094221.GA10957@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
config is available
[ Upstream commit d2f42e09393c774ab79088d8e3afcc62b3328fc9 ]
If no suitable DMA configuration is available, a previous 'bdc_phy_init()'
call must be undone by a corresponding 'bdc_phy_exit()' call.
Branch to the existing error handling path instead of returning
directly.
Fixes: cc29d4f67757 ("usb: bdc: Add support for USB phy")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0c5910979f39225d5d8fe68c9ab1c147c68ddee1.1629314734.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2af0c5ffadaf9d13eca28409d4238b4e672942d3 ]
If IRQ occurs between calling request_irq() and mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 50855c31573b02963f0aa2aacfd4ea41c31ae0e0 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8b2e76687b39 ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e752dbc59e1241b13b8c4f7b6eb582862e7668fe upstream.
The usb3_start_pipen() is called by renesas_usb3_ep_queue() and
usb3_request_done_pipen() so that usb3_start_pipen() is possible
to cause a race when getting usb3_first_req like below:
renesas_usb3_ep_queue()
spin_lock_irqsave()
list_add_tail()
spin_unlock_irqrestore()
usb3_start_pipen()
usb3_first_req = usb3_get_request() --- [1]
--- interrupt ---
usb3_irq_dma_int()
usb3_request_done_pipen()
usb3_get_request()
usb3_start_pipen()
usb3_first_req = usb3_get_request()
...
(the req is possible to be finished in the interrupt)
The usb3_first_req [1] above may have been finished after the interrupt
ended so that this driver caused to start a transfer wrongly. To fix this
issue, getting/checking the usb3_first_req are under spin_lock_irqsave()
in the same section.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210524060155.1178724-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_resource
[ Upstream commit 9c2076090c2815fe7c49676df68dde7e60a9b9fc ]
The call to platform_get_resource can potentially return a NULL pointer
on failure, so add this check and return -EINVAL if it fails.
Fixes: c41442474a26 ("usb: gadget: R8A66597 peripheral controller support.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference null return")
Link: https://lore.kernel.org/r/20210406184510.433497-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e3d055bf27d70204cae349335a62a4f9b7c165a ]
IS_ERR() and PTR_ERR() use wrong pointer, it should be
udc->virt_addr, fix it.
Fixes: 1b9f35adb0ff ("usb: gadget: udc: Add Synopsys UDC Platform driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210330130159.1051979-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd4d607044b961cecbf8c4c2f3bb5da4fb156993 ]
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
[<80106550>] show_stack+0x20/0x24
[<80106868>] dump_stack+0x28/0x30
[<80823540>] __warn+0xfc/0x110
[<8011ac30>] warn_slowpath_fmt+0xb0/0xc0
[<8011ad44>] dma_map_page_attrs+0x24c/0x314
[<8016a27c>] usb_gadget_map_request_by_dev+0x100/0x1e4
[<805cedd8>] usb_gadget_map_request+0x1c/0x20
[<805cefbc>] ast_vhub_epn_queue+0xa0/0x1d8
[<7f02f710>] usb_ep_queue+0x48/0xc4
[<805cd3e8>] ecm_do_notify+0xf8/0x248
[<7f145920>] ecm_set_alt+0xc8/0x1d0
[<7f145c34>] composite_setup+0x680/0x1d30
[<7f00deb8>] ast_vhub_ep0_handle_setup+0xa4/0x1bc
[<7f02ee94>] ast_vhub_dev_irq+0x58/0x84
[<7f0309e0>] ast_vhub_irq+0xb0/0x1c8
[<7f02e118>] __handle_irq_event_percpu+0x50/0x19c
[<8015e5bc>] handle_irq_event_percpu+0x38/0x8c
[<8015e758>] handle_irq_event+0x38/0x4c
Fixes: 7ecca2a4080c ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210331045831.28700-1-rentao.bupt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75bb93be0027123b5db6cbcce89eb62f0f6b3c5b ]
A short packet indicates the end of a transfer and marks the request as
complete.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-8-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e7c2510bdfe89a9ec223dd7acd6bfc8bb1cbeb6 ]
Before this, it wrote as much as available into the buffer, even if it
didn't fit.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-7-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9aee3a23d6455200702f3a57e731fa11e8408667 ]
Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-5-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c7f755b243494d6043aadcd9a2989cb157958b95 ]
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-4-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 078ba935651e149c92c41161e0322e3372cc2705 ]
For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-3-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 755915fc28edfc608fa89a163014acb2f31c1e19 ]
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a28d77e359009b846951b06f7c0d8eec8dce298 ]
DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:
DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]
Fixes: abab0c67c061 ("usb: pch_udc: Fixed issue which does not work with g_serial")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fbdbbe6d3ee502b3bdeb4f255196bb45003614be ]
Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:
[ 55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[ 55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[ 55.245843] <IRQ>
[ 55.245843] ? pch_udc_svc_data_out+0x160/0x160
Check if driver is present before calling ->setup().
Fixes: f646cf94520e ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91356fed6afd1c83bf0d3df1fc336d54e38f0458 ]
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Fixes: f646cf94520e ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 50a318cc9b54a36f00beadf77e578a50f3620477 upstream.
The commit d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a12138 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd38 ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88e6 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a5d797a9f9c4f18585544237216d7812686a71f upstream.
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72035f4954f0bca2d8c47cf31b3629c42116f5b7 upstream.
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool.
however, dev->dev is actually set after calling init_dma_pools(), which
effectively makes dma_pool_create(..NULL) and cause crash.
To fix this issue, init dma only after dev->dev is set.
[ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290
[ 1.323257] Call Trace:
[ 1.323390] ? pci_write_config_word+0x27/0x30
[ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core]
[ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci]
Fixes: 7c51247a1f62 (usb: gadget: udc: Provide correct arguments for 'dma_pool_create')
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef02684c4e67d8c35ac83083564135bc7b1d3445 upstream.
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c28095bc99073ddda65e4f31f6ae0d908d4d5cd8 upstream.
Use lock to guard against concurrent access for soft-connect/disconnect
operations when writing to soft_connect sysfs.
Fixes: 2ccea03a8f7e ("usb: gadget: introduce UDC Class")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/338ea01fbd69b1985ef58f0f59af02c805ddf189.1610611437.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e0dcf62ab4cf917d0cbe751b8bf229a065248d4 upstream.
The vhub engine has two dma mode, one is descriptor list, another
is single stage DMA. Each mode has different stop register setting.
Descriptor list operation (bit2) : 0 disable reset, 1: enable reset
Single mode operation (bit0) : 0 : disable, 1: enable
Fixes: 7ecca2a4080c ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210108081238.10199-2-ryan_chen@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e90cfa813da7a527785033a0b247594c2de93dd8 upstream.
This error path
err_add_pdata:
for (i = 0; i < mod_data.num; i++)
kfree(dum[i]);
can be triggered when not all dum's elements are initialized.
Fix this by initializing all dum's elements to NULL.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/1607063090-3426-1-git-send-email-minhquangbui99@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0d66e04875c5aae876cf3d4f4be7978fa2b00523 ]
goku_probe() goes to error label "err" and invokes goku_remove()
in case of failures of pci_enable_device(), pci_resource_start()
and ioremap(). goku_remove() gets a device from
pci_get_drvdata(pdev) and works with it without any checks, in
particular it dereferences a corresponding pointer. But
goku_probe() did not set this device yet. So, one can expect
various crashes. The patch moves setting the device just after
allocation of memory for it.
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5fc453d7de3d0c345812453823a3a56783c5f82c ]
GISB bus error kernel panics have been observed during S2 transition
tests on the 7271t platform. The errors are a result of the BDC
interrupt handler trying to access BDC register space after the
system's suspend callbacks have completed.
Adding a suspend hook to the BDC driver that halts the controller before
S2 entry thus preventing unwanted access to the BDC register space during
this transition.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a95bdfd22076497288868c028619bc5995f5cc7f ]
Multiple connects/disconnects can cause a crash on the second
disconnect. The driver had a problem where it would try to send
endpoint commands after it was disconnected which is not allowed
by the hardware. The fix is to only allow the endpoint commands
when the endpoint is connected. This will also fix issues that
showed up when using configfs to create gadgets.
Signed-off-by: Sasi Kumar <sasi.kumar@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2468c877da428ebfd701142c4cdfefcfb7d4c00e ]
Driver does not release memory for device on error handling paths in
net2280_probe() when gadget_release() is not registered yet.
The patch fixes the bug like in other similar drivers.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8f8529e2c4141afa2ebb487ad48e8a6ec3e8c99 ]
gr_ep_init() does not assign the allocated request anywhere if allocation
of memory for the buffer fails. This is a memory leak fixed by the given
patch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30517ffeb3bff842e1355cbc32f1959d9dbb5414 ]
Fixed commit moved the assignment of 'req', but did not update a
reference in the DBG() call. Use the argument as it was renamed.
Fixes: 5fb694f96e7c ("usb: gadget: udc: atmel: fix possible oops when unloading module")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e55f3c37cb8d31c7e301f46396b2ac6a19eb3a7c ]
If this is in "transceiver" mode the the ->qwork isn't required and is
a NULL pointer. This can lead to a NULL dereference when we call
destroy_workqueue(udc->qwork).
Fixes: 3517c31a8ece ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44734a594196bf1d474212f38fe3a0d37a73278b ]
m66592_free_request() is called under label "err_add_udc"
and "clean_up", and m66592->ep0_req is not set to NULL after
first free, leading to a double-free. Fix this issue by
setting m66592->ep0_req to NULL after the first free.
Fixes: 0f91349b89f3 ("usb: gadget: convert all users to the new udc infrastructure")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eafa80041645cd7604c4357b1a0cd4a3c81f2227 ]
Currently pointer ep is being dereferenced before it is null checked
leading to a null pointer dereference issue. Fix this by only assigning
pointer udc once ep is known to be not null. Also remove a debug
message that requires a valid udc which may not be possible at that
point.
Addresses-Coverity: ("Dereference before null check")
Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a0fbcf7c308920bc6116b3a5fb21c8cc5fec128 ]
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~
1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.
Commit afe956c577b2d ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.
Fixes: 3fc154b6b8134 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ce26a1c31ca928df4dfc7504c8898b71ff9f5d5 ]
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
'net2272_plat_probe()'
commit ccaef7e6e354fb65758eaddd3eae8065a8b3e295 upstream.
'dev' is allocated in 'net2272_probe_init()'. It must be freed in the error
handling path, as already done in the remove function (i.e.
'net2272_plat_remove()')
Fixes: 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09b04abb70f096333bef6bc95fa600b662e7ee13 upstream.
When building with Clang + -Wtautological-pointer-compare:
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:28: warning: comparison of
address of 'req->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~ ~~~~
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:51: warning: comparison of
address of 'req->usb_req' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~~~ ~~~~
2 warnings generated.
As it notes, these statements will always evaluate to false so remove
them.
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Link: https://github.com/ClangBuiltLinux/linux/issues/749
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9c1ed62ae0690dfe5d5e31d8f70e70a95cb48e52 ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.
To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ab2b48c98f2ec9712452d520a381917f91ac3d2 ]
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Piyush Mehta
Ma Ke
Dan Carpenter
Zheng Wang
Linus Walleij
Justin Chen
Randy Dunlap
Miaoqian Lin
Alan Stern
Szymon Heidrich
Geert Uytterhoeven
Dan Carpenter
Christophe JAILLET
Nadezda Lutovinova
Sergey Shtylyov
Yoshihiro Shimoda
Colin Ian King
Yang Yingliang
Tao Ren
Fabian Vogt
Andy Shevchenko
Anirudh Rayabharam
Tong Zhang
Patrik Jakobsson
Thinh Nguyen
Ryan Chen
Bui Quang Minh
Evgeny Novikov
Danesh Petigara
Sasi Kumar
Michał Mirosław
Qiushi Wu
Nathan Chancellor
Jia-Ju Bai
Nicholas Mc Guire