| Age | Commit message (Collapse) | Author |
|---|
|
commit 6d735722063a945de56472bdc6bfcb170fd43b86 upstream.
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe82 ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b191a18cb5c47109ca696370a74a5062a70adfd0 upstream.
Don't go through soft-disconnection sequence if the controller hasn't
started. Otherwise, there will be timeout and warning reports from the
soft-disconnection flow.
Cc: stable@vger.kernel.org
Fixes: 61a348857e86 ("usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-usb/20240215233536.7yejlj3zzkl23vjd@synopsys.com/T/#mb0661cd5f9272602af390c18392b9a36da4f96e6
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e3be9b929934e0680a6f4b8f6eb11b18ae9c7e07.1708043922.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4e3ef5685393c5051b52cf1e94b8891d49793ab upstream.
If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb60136 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39674be56fba1cd3a03bf4617f523a35f85fd2c1 upstream.
Do not call gadget stop until the poll for controller halt is
completed. DEVTEN is cleared as part of gadget stop, so the intention to
allow ep0 events to continue while waiting for controller halt is not
happening.
Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4db0fbb601361767144e712beb96704b966339f5 upstream.
The gadget driver may wait on the request completion when it sets the
USB_GADGET_DELAYED_STATUS. Make sure that the End Transfer command can
go through if the dwc->delayed_status is set so that the request can
complete. When the delayed_status is set, the Setup packet is already
processed, and the next phase should be either Data or Status. It's
unlikely that the host would cancel the control transfer and send a new
Setup packet during End Transfer command. But if that's the case, we can
try again when ep0state returns to EP0_SETUP_PHASE.
Fixes: e1ee843488d5 ("usb: dwc3: gadget: Force sending delayed status during soft disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3f9f59e5d74efcbaee444cf4b30ef639cc7b124e.1666146954.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3c7af52c7616c3aa6dacd2336ec748d4a65df8f4 ]
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 730e12fbec53ab59dd807d981a204258a4cfb29a ]
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Fixes: fcd2def66392 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f40fc0808137c157dd408d2632e63bfca2aecdb ]
Several sequences utilize the same routine for forcing the control endpoint
back into the SETUP phase. This is required, because those operations need
to ensure that EP0 is back in the default state.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02435a739b81ae24aff5d6e930efef9458e2af3c ]
It was observed that there are hosts that may complete pending SETUP
transactions before the stop active transfers and controller halt occurs,
leading to lingering endxfer commands on DEPs on subsequent pullup/gadget
start iterations.
dwc3_gadget_ep_disable name=ep8in flags=0x3009 direction=1
dwc3_gadget_ep_disable name=ep4in flags=1 direction=1
dwc3_gadget_ep_disable name=ep3out flags=1 direction=0
usb_gadget_disconnect deactivated=0 connected=0 ret=0
The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0))
routine completed successfully, allowing for the USB gadget to proceed with
a USB gadget connect. However, if this occurs the system runs into an
issue where:
BUG: spinlock already unlocked on CPU
spin_bug+0x0
dwc3_remove_requests+0x278
dwc3_ep0_out_start+0xb0
__dwc3_gadget_start+0x25c
This is due to the pending endxfers, leading to gadget start (w/o lock
held) to execute the remove requests, which will unlock the dwc3
spinlock as part of giveback.
To mitigate this, resolve the pending endxfers on the pullup disable
path by re-locating the SETUP phase check after stop active transfers, since
that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows
for handling of a host that may be unresponsive by using the completion
timeout to trigger the stall and restart for EP0.
Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230413195742.11821-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8422b769fa46bd429dc0f324012629a4691f0dd9 ]
During a cable disconnect sequence, if ep0state is not in the SETUP phase,
then nothing will trigger any pending end transfer commands. Force
stopping of any pending SETUP transaction, and move back to the SETUP
phase.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e1ee843488d58099a89979627ef85d5bd6c5cacd ]
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d778f0c5f95ca5aa2ff628ea281978697e8d89b ]
According to the databook ep0 should be in setup phase during reset.
If host issues reset between control transfers, ep0 will be in an
invalid state. Fix this by issuing stall and restart on ep0 if it
is not in setup phase.
Also SW needs to complete pending control transfer and setup core for
next setup stage as per data book. Hence check ep0 state during reset
interrupt handling and make sure active transfers on ep0 out/in
endpoint are stopped by queuing ENDXFER command for that endpoint and
restart ep0 out again to receive next setup packet.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1651693001-29891-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f66eef8fb8989a7193cafc3870f7c7b2b97f16cb ]
If the controller hasn't DMA'ed the Setup data from its fifo, it won't
process the End Transfer command. Polling for the command completion may
block the driver from servicing the Setup phase and cause a timeout.
Previously we only check and delay issuing End Transfer in the case of
endpoint dequeue. Let's do that for all End Transfer scenarios.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2fcf3b5d90068d549589a57a27a79f76c6769b04.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ace17b6ee4f92ab0375d12a1b42494f8590a96b6 ]
The driver shouldn't be able to issue End Transfer to the control
endpoint at anytime. Typically we should only do so in error cases such
as invalid/unexpected direction of Data Phase as described in the
control transfer flow of the programming guide. It _may_ end started
data phase during controller deinitialization from soft disconnect or
driver removal. However, that should not happen because the driver
should be maintained in EP0_SETUP_PHASE during driver tear-down. On
soft-connect, the controller should be reset from a soft-reset and there
should be no issue starting the control endpoint.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3c6643678863a26702e4115e9e19d7d94a30d49c.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c96683798e272366866a5c0ce3073c0b5a256db7 ]
Since we can't guarantee that the host won't send new Setup packet
before going through the device-initiated disconnect, don't prepare
beyond the Setup stage and keep the device in EP0_SETUP_PHASE. This
ensures that the device-initated disconnect sequence can go through
gracefully. Note that the controller won't service the End Transfer
command if it can't DMA out the Setup packet.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6bacec56ecabb2c6e49a09cedfcac281fdc97de0.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4cf6580ac740f766dae26203bd6311d353dcd42 ]
If a Setup packet is received but yet to DMA out, the controller will
not process the End Transfer command of any endpoint. Polling of its
DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
command timeout.
This may occur if the driver doesn’t service the completion interrupt of
the control status stage yet due to system latency, then it won’t
prepare TRB and start the transfer for the next Setup Stage. To the host
side, the control transfer had completed, and the host can send a new
Setup packet at this point.
In the meanwhile, if the driver receives an async call to dequeue a
request (triggering End Transfer) to any endpoint, then the driver will
service that End transfer first, blocking the control status stage
completion handler. Since no TRB is available for the Setup stage, the
Setup packet can’t be DMA’ed out and the End Transfer gets hung.
The driver must not block setting up of the Setup stage. So track and
only issue the End Transfer command only when there’s Setup TRB prepared
so that the controller can DMA out the Setup packet. Delay the End
transfer command if there's no Setup TRB available. This is applicable to
all DWC_usb3x IPs.
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220309205402.4467-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 730e12fbec53 ("usb: dwc3: gadget: Handle EP0 request dequeuing properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 61a348857e869432e6a920ad8ea9132e8d44c316 upstream.
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c29 ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 817349b6d26aadd8b38283a05ce0bab106b4c765 upstream.
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afe28cd686aeb77e8d9140d50fb1cf06a7ecb731 upstream.
This reverts commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7.
Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).
Cc: <stable@vger.kernel.org>
Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7059fbebcb00554c3f31e5b5d93ef6d2d96dc7b4 upstream.
This reverts commit 8bea147dfdf823eaa8d3baeccc7aeb041b41944b.
The phy soft reset GUSB2PHYCFG.PHYSOFTRST only applies to UTMI phy, not
ULPI. This fix is incomplete.
Cc: <stable@vger.kernel.org>
Fixes: 8bea147dfdf8 ("usb: dwc3: Soft reset phy on probe for host")
Reported-by: Köry Maincent <kory.maincent@bootlin.com>
Closes: https://lore.kernel.org/linux-usb/20231205151959.5236c231@kmaincent-XPS-13-7390
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/29a26593a60eba727de872a3e580a674807b3339.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9d40b215e38480fd94c66b06d79045717a59e9c upstream.
Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().
Code Flow:
CPU1
->Gadget_start
->dwc3_interrupt
->dwc3_thread_interrupt
->dwc3_process_event_buf
->dwc3_process_event_entry
->dwc3_endpoint_interrupt
->dwc3_ep0_interrupt
->dwc3_ep0_inspect_setup
->dwc3_ep0_stall_and_restart
By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.
Cc: <stable@vger.kernel.org>
Fixes: d742220b3577 ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41f5a0973259db9e4e3c9963d36505f80107d1a0 upstream.
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9feefbf57d92e8ee293dad67585d351c7d0b6e37 upstream.
Make sure to remove the software node also on (ACPI) probe errors to
avoid leaking the underlying resources.
Note that the software node is only used for ACPI probe so the driver
unbind tear down is updated to match probe.
Fixes: 8dc6e6dd1bee ("usb: dwc3: qcom: Constify the software node")
Cc: stable@vger.kernel.org # 5.12
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8bbae288a85abed6a1cf7d185d8b9dc2f5dcb12c upstream.
Allow devices to have dma operations beyond 4K, and avoid warnings such
as:
DMA-API: dwc3 a600000.usb: mapping sg segment longer than device claims to support [len=86016] [max=65536]
Cc: stable@vger.kernel.org
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Reported-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231026-dwc3-v2-1-1d4fd5c3e067@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10d510abd096d620b9fda2dd3e0047c5efc4ad2b upstream.
The default mode, configurable by DT, shall be set before usb role switch
driver is registered. Otherwise there is a race between default mode
and mode set by usb role switch driver.
Fixes: 98ed256a4dbad ("usb: dwc3: Add support for role-switch-default-mode binding")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231025095110.2405281-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9cf87666fc6e08572341fe08ecd909935998fbbd ]
Make sure to free the "urs" platform device, which is created for some
ACPI platforms, on probe errors and on driver unbind.
Compile-tested only.
Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20231117173650.21161-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 51392a1879ff06dc21b68aef4825f6ef68a7be42 ]
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()")
Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI")
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc6e ("USB: dwc3: qcom: fix ACPI platform device leak")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8bea147dfdf823eaa8d3baeccc7aeb041b41944b upstream.
When there's phy initialization, we need to initiate a soft-reset
sequence. That's done through USBCMD.HCRST in the xHCI driver and its
initialization, However, the dwc3 driver may modify core configs before
the soft-reset. This may result in some connection instability. So,
ensure the phy is ready before the controller updates the GCTL.PRTCAPDIR
or other settings by issuing phy soft-reset.
Note that some host-mode configurations may not expose device registers
to initiate the controller soft-reset (via DCTL.CoreSftRst). So we reset
through GUSB3PIPECTL and GUSB2PHYCFG instead.
Cc: stable@vger.kernel.org
Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Reported-by: Kenta Sato <tosainu.maple@gmail.com>
Closes: https://lore.kernel.org/linux-usb/ZPUciRLUcjDywMVS@debian.me/
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Kenta Sato <tosainu.maple@gmail.com>
Link: https://lore.kernel.org/r/70aea513215d273669152696cc02b20ddcdb6f1a.1694564261.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1fa206bb764f37d2ab4bf671e483153ef0659b34 upstream.
Device connected to usb otg port of GXL-based boards can not be
recognised after resumption, doesn't recover even if disconnect and
reconnect the device. dmesg shows it disconnects during resumption.
[ 41.492911] usb 1-2: USB disconnect, device number 3
[ 41.499346] usb 1-2: unregistering device
[ 41.511939] usb 1-2: unregistering interface 1-2:1.0
Calling usb_post_init() will fix this issue, and it's tested and
verified on libretech's aml-s905x-cc board.
Cc: stable@vger.kernel.org # v5.8+
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Signed-off-by: Luke Lu <luke.lu@libre.computer>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230809212911.18903-1-luke.lu@libre.computer
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3dbb657571509044be15184a13134fa7c1fdca1 ]
Some dwc3 glue drivers are currently accessing the driver data of the
child core device directly, which is clearly a bad idea as the child may
not have probed yet or may have been unbound from its driver.
As a workaround until the glue drivers have been fixed, clear the driver
data pointer before allowing the glue parent device to runtime suspend
to prevent its driver from accessing data that has been freed during
unbind.
Fixes: 6dd2565989b4 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Fixes: 6895ea55c385 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Cc: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Message-ID: <20230607100540.31045-3-johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d2d69354226de0b333d4405981f3d9c41ba8430a ]
The Qualcomm dwc3 glue driver is currently accessing the driver data of
the child core device during suspend and on wakeup interrupts. This is
clearly a bad idea as the child may not have probed yet or could have
been unbound from its driver.
The first such layering violation was part of the initial version of the
driver, but this was later made worse when the hack that accesses the
driver data of the grand child xhci device to configure the wakeup
interrupts was added.
Fixing this properly is not that easily done, so add a sanity check to
make sure that the child driver data is non-NULL before dereferencing it
for now.
Note that this relies on subtleties like the fact that driver core is
making sure that the parent is not suspended while the child is probing.
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/all/20230325165217.31069-4-manivannan.sadhasivam@linaro.org/
Fixes: d9152161b4bf ("usb: dwc3: Add Qualcomm DWC3 glue layer driver")
Fixes: 6895ea55c385 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Cc: stable@vger.kernel.org # 3.18: a872ab303d5d: "usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup"
Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Cc: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Message-ID: <20230607100540.31045-2-johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8540870af4ce6ddeb27a7bb5498b75fb29b643c ]
Prevent -ETIMEDOUT error on .suspend().
e.g. If gadget driver is loaded and we are connected to a USB host,
all transfers must be stopped before stopping the controller else
we will not get a clean stop i.e. dwc3_gadget_run_stop() will take
several seconds to complete and will return -ETIMEDOUT.
Handle error cases properly in dwc3_gadget_suspend().
Simplify dwc3_gadget_resume() by using the introduced helper function.
Fixes: 9f8a67b65a49 ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230503110048.30617-1-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdb19d01026a5cccfa437be8adcf2df472c5889e ]
The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.
Remove the hibernation bits from the gadget code, which effectively
reverts commits e1dadd3b0f27 ("usb: dwc3: workaround: bogus hibernation
events") and 7b2a0368bbc9 ("usb: dwc3: gadget: set KEEP_CONNECT in case
of hibernation") except for the spurious interrupt warning.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: c8540870af4c ("usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit af870d93c706c302a8742d7c751a60a832f7bc64 ]
Fixes the following two typos:
1. reinitate -> reinitiate
2. revison -> revision
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/HK0PR01MB280110FAB74B4B2ACE32EA5FF8479@HK0PR01MB2801.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: c8540870af4c ("usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5265397f94424eaea596026fd34dc7acf474dcec ]
Remove the need for making dwc3_gadget_suspend() and dwc3_gadget_resume()
to be called in a spinlock, as dwc3_gadget_run_stop() could potentially
take some time to complete.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: c8540870af4c ("usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9711c67de7482c81e1daca3548fbc5c9603600e3 ]
Ensure that there are no pending events being handled in between soft
connect/disconnect transitions. As we are keeping interrupts enabled,
and EP0 events are still being serviced, this avoids any stale events from
being serviced.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: c8540870af4c ("usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3ddaa6a274578e23745b7466346fc2650df8f959 upstream.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7 upstream.
Commit c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b32b8f2b9542d8039f5468303a6ca78c1b5611a5 upstream.
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.
Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.
However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".
With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.
This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.
Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 734ae15ab95a18d3d425fc9cb38b7a627d786f08 upstream.
This reverts commit b138e23d3dff90c0494925b4c1874227b81bddf7.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 01052b91c9808e3c3b068ae2721cb728ec9aa4c0 ]
If dwc3_meson_g12a_otg_init() fails, resources allocated by the previous
of_platform_populate() call should be released, as already done in the
error handling path.
Fixes: 1e355f21d3fb ("usb: dwc3: Add Amlogic A1 DWC3 glue")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Message-ID: <9d28466de1808ccc756b4cc25fc72c482d133d13.1686403934.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a944da707123686d372ec01ea60056902fadf35 ]
If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to
be released, as already done in the other error handling path of the
probe.
Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8fd95da2cfb5046c4bb5a3cdc9eb7963ba8b10dd ]
In the probe, some resources are allocated with
dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The
corresponding resources are already coorectly freed in the error handling
path of the probe, but not in the remove function.
Fix it.
Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 097fb3ee710d4de83b8d4f5589e8ee13e0f0541e ]
Function dwc3_qcom_probe() allocates memory for resource structure
which is pointed by parent_res pointer. This memory is not
freed. This leads to memory leak. Use stack memory to prevent
memory leak.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c0aabed9cabe057309779a9e26fe86a113d24dad upstream.
In scenarios where pullup relies on resume (get sync) to initialize
the controller and set the run stop bit, then core_init is followed by
gadget_resume which will eventually set run stop bit.
But in cases where the core_init fails, the return value is not sent
back to udc appropriately. So according to UDC the controller has
started but in reality we never set the run stop bit.
On systems like Android, there are uevents sent to HAL depending on
whether the configfs_bind / configfs_disconnect were invoked. In the
above mentioned scnenario, if the core init fails, the run stop won't
be set and the cable plug-out won't result in generation of any
disconnect event and userspace would never get any uevent regarding
cable plug out and we never call pullup(0) again. Furthermore none of
the next Plug-In/Plug-Out's would be known to configfs.
Return back the appropriate result to UDC to let the userspace/
configfs know that the pullup failed so they can take appropriate
action.
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00f8205ffcf112dcef14f8151d78075d38d22c08 upstream.
Consider a scenario where cable disconnect happens when there is an active
usb reqest queued to the UDC. As part of the disconnect we would issue an
end transfer with no interrupt-on-completion before giving back this
request. Since we are giving back the request without skipping TRBs the
num_trbs field of dwc3_request still holds the stale value previously used.
Function drivers re-use same request for a given bind-unbind session and
hence their dwc3_request context gets preserved across cable
disconnect/connect. When such a request gets re-queued after cable connect,
we would increase the num_trbs field on top of the previous stale value
thus incorrectly representing the number of TRBs used. Fix this by
resetting num_trbs field before giving back the request.
Fixes: 09fe1f8d7e2f ("usb: dwc3: gadget: track number of TRBs per request")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4e8ef34e36f2839ef8c8da521ab7035956436818 ]
When work in gadget mode, currently driver doesn't update software level
link_state correctly as link state change event is not enabled for most
devices, in function dwc3_gadget_suspend_interrupt(), it will only pass
suspend event to UDC core when software level link state changes, so when
interrupt generated in sequences of suspend -> reset -> conndone ->
suspend, link state is not updated during reset and conndone, so second
suspend interrupt event will not pass to UDC core.
Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a
suspended flag to replace the compare function.
Fixes: 799e9dc82968 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 614ce6a2ea50068b45339257891e51e639ac9001 upstream.
When the dwc3 device is runtime suspended, various required clocks are in
disabled state and it is not guaranteed that access to any registers would
work. Depending on the SoC glue, a register read could be as benign as
returning 0 or be fatal enough to hang the system.
In order to prevent such scenarios of fatal errors, make sure to resume
dwc3 then allow the function to proceed.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org #3.2: 30332eeefec8: debugfs: regset32: Add Runtime PM support
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230509144836.6803-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4decf4060ecfee1f7a710999fcd421645ac0c419 ]
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 44d257e9012ee8040e41d224d0e5bfb5ef5427ea upstream.
Make sure to balance the runtime PM usage count on driver unbind by
adding back the pm_runtime_allow() call that had been erroneously
removed.
Fixes: 266d0493900a ("usb: dwc3: core: don't trigger runtime pm when remove driver")
Cc: stable@vger.kernel.org # 5.9
Cc: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Thinh Nguyen
Wesley Cheng
Mayank Rana
Uttkarsh Aggarwal
Prashanth K
Johan Hovold
Ricardo Ribalda
Alexander Stein
Luke Lu
Roger Quadros
Kushagra Verma
Elson Roy Serrao
Jisheng Zhang
Gratian Crisan
Jakub Vanek
Christophe JAILLET
Vladislav Efanov
Krishna Kurapati
Linyu Yuan
Udipto Goswami