| Age | Commit message (Collapse) | Author |
|---|
|
commit 534cf755d9df99e214ddbe26b91cd4d81d2603e2 upstream.
Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:
| sysrq: Changing Loglevel
| sysrq: Loglevel set to 9
|
| ======================================================
| WARNING: possible circular locking dependency detected
| 5.9.0-rc7 #1 Not tainted
| ------------------------------------------------------
| systemd-journal/138 is trying to acquire lock:
| ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
|
| but task is already holding lock:
| ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
|
| which lock already depends on the new lock.
[...]
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock(&port_lock_key);
| lock(console_owner);
| lock(&port_lock_key);
| lock(console_owner);
|
| *** DEADLOCK ***
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9ca43d42ed8d5fd635d327a664ed1d8579eb2af upstream.
For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.
Commit ce734600545f ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).
As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.
So, fix the logic to detect QUP with versions 2.5 and above.
Fixes: ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Paras Sharma <parashar@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29788ab1d2bf26c130de8f44f9553ee78a27e8d5 upstream.
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ea40db477c024dcb87321b7f32bd6ea12130ac2 upstream.
The 2nd and 3rd parameter were wrongly used, and cause kernel abort when
doing kgdb debug.
Fixes: 1da17d7cf8e2 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db332356222d9429731ab9395c89cca403828460 ]
ipwireless_send_packet() can only return 0 on success and -ENOMEM on
error, the caller should check non zero for error condition
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 71a174b39f10b4b93223d374722aa894b5d8a82e ]
b6da31b2c07c "tty: Fix data race in tty_insert_flip_string_fixed_flag"
puts tty_flip_buffer_push under port->lock introducing the following
possible circular locking dependency:
[30129.876566] ======================================================
[30129.876566] WARNING: possible circular locking dependency detected
[30129.876567] 5.9.0-rc2+ #3 Tainted: G S W
[30129.876568] ------------------------------------------------------
[30129.876568] sysrq.sh/1222 is trying to acquire lock:
[30129.876569] ffffffff92c39480 (console_owner){....}-{0:0}, at: console_unlock+0x3fe/0xa90
[30129.876572] but task is already holding lock:
[30129.876572] ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca
[30129.876576] which lock already depends on the new lock.
[30129.876577] the existing dependency chain (in reverse order) is:
[30129.876578] -> #3 (&pool->lock/1){-.-.}-{2:2}:
[30129.876581] _raw_spin_lock+0x30/0x70
[30129.876581] __queue_work+0x1a3/0x10f0
[30129.876582] queue_work_on+0x78/0x80
[30129.876582] pty_write+0x165/0x1e0
[30129.876583] n_tty_write+0x47f/0xf00
[30129.876583] tty_write+0x3d6/0x8d0
[30129.876584] vfs_write+0x1a8/0x650
[30129.876588] -> #2 (&port->lock#2){-.-.}-{2:2}:
[30129.876590] _raw_spin_lock_irqsave+0x3b/0x80
[30129.876591] tty_port_tty_get+0x1d/0xb0
[30129.876592] tty_port_default_wakeup+0xb/0x30
[30129.876592] serial8250_tx_chars+0x3d6/0x970
[30129.876593] serial8250_handle_irq.part.12+0x216/0x380
[30129.876593] serial8250_default_handle_irq+0x82/0xe0
[30129.876594] serial8250_interrupt+0xdd/0x1b0
[30129.876595] __handle_irq_event_percpu+0xfc/0x850
[30129.876602] -> #1 (&port->lock){-.-.}-{2:2}:
[30129.876605] _raw_spin_lock_irqsave+0x3b/0x80
[30129.876605] serial8250_console_write+0x12d/0x900
[30129.876606] console_unlock+0x679/0xa90
[30129.876606] register_console+0x371/0x6e0
[30129.876607] univ8250_console_init+0x24/0x27
[30129.876607] console_init+0x2f9/0x45e
[30129.876609] -> #0 (console_owner){....}-{0:0}:
[30129.876611] __lock_acquire+0x2f70/0x4e90
[30129.876612] lock_acquire+0x1ac/0xad0
[30129.876612] console_unlock+0x460/0xa90
[30129.876613] vprintk_emit+0x130/0x420
[30129.876613] printk+0x9f/0xc5
[30129.876614] show_pwq+0x154/0x618
[30129.876615] show_workqueue_state.cold.55+0x193/0x6ca
[30129.876615] __handle_sysrq+0x244/0x460
[30129.876616] write_sysrq_trigger+0x48/0x4a
[30129.876616] proc_reg_write+0x1a6/0x240
[30129.876617] vfs_write+0x1a8/0x650
[30129.876619] other info that might help us debug this:
[30129.876620] Chain exists of:
[30129.876621] console_owner --> &port->lock#2 --> &pool->lock/1
[30129.876625] Possible unsafe locking scenario:
[30129.876626] CPU0 CPU1
[30129.876626] ---- ----
[30129.876627] lock(&pool->lock/1);
[30129.876628] lock(&port->lock#2);
[30129.876630] lock(&pool->lock/1);
[30129.876631] lock(console_owner);
[30129.876633] *** DEADLOCK ***
[30129.876634] 5 locks held by sysrq.sh/1222:
[30129.876634] #0: ffff8881d3ce0470 (sb_writers#3){.+.+}-{0:0}, at: vfs_write+0x359/0x650
[30129.876637] #1: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: __handle_sysrq+0x4d/0x460
[30129.876640] #2: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: show_workqueue_state+0x5/0xf0
[30129.876642] #3: ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca
[30129.876645] #4: ffffffff92c39980 (console_lock){+.+.}-{0:0}, at: vprintk_emit+0x123/0x420
[30129.876648] stack backtrace:
[30129.876649] CPU: 3 PID: 1222 Comm: sysrq.sh Tainted: G S W 5.9.0-rc2+ #3
[30129.876649] Hardware name: Intel Corporation 2012 Client Platform/Emerald Lake 2, BIOS ACRVMBY1.86C.0078.P00.1201161002 01/16/2012
[30129.876650] Call Trace:
[30129.876650] dump_stack+0x9d/0xe0
[30129.876651] check_noncircular+0x34f/0x410
[30129.876653] __lock_acquire+0x2f70/0x4e90
[30129.876656] lock_acquire+0x1ac/0xad0
[30129.876658] console_unlock+0x460/0xa90
[30129.876660] vprintk_emit+0x130/0x420
[30129.876660] printk+0x9f/0xc5
[30129.876661] show_pwq+0x154/0x618
[30129.876662] show_workqueue_state.cold.55+0x193/0x6ca
[30129.876664] __handle_sysrq+0x244/0x460
[30129.876665] write_sysrq_trigger+0x48/0x4a
[30129.876665] proc_reg_write+0x1a6/0x240
[30129.876666] vfs_write+0x1a8/0x650
It looks like the commit was aimed to protect tty_insert_flip_string and
there is no need for tty_flip_buffer_push to be under this lock.
Fixes: b6da31b2c07c ("tty: Fix data race in tty_insert_flip_string_fixed_flag")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200902120045.3693075-1-asavkov@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63ffcbdad738e3d1c857027789a2273df3337624 ]
The code currently NULLs tty->driver_data in hvcs_close() with the
intent of informing the next call to hvcs_open() that device needs to be
reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from
tty->driver_data which was previoulsy NULLed by hvcs_close() and our
call to tty_port_put(&hvcsd->port) doesn't actually do anything since
&hvcsd->port ends up translating to NULL by chance. This has the side
effect that when hvcs_remove() is called we have one too many port
references preventing hvcs_destuct_port() from ever being called. This
also prevents us from reusing the /dev/hvcsX node in a future
hvcs_probe() and we can eventually run out of /dev/hvcsX devices.
Fix this by waiting to NULL tty->driver_data in hvcs_cleanup().
Fixes: 27bf7c43a19c ("TTY: hvcs, add tty install")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20200820234643.70412-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ]
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ]
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff62255a2a5c1228a28f2bb063646f948115a309 ]
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200427122415.47416-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ]
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ]
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
probe
[ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ]
When booting j721e the following bug is printed:
[ 1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[ 1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[ 1.154832] 3 locks held by kworker/0:1/12:
[ 1.154836] #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[ 1.154852] #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[ 1.154860] #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[ 1.154872] irq event stamp: 63096
[ 1.154881] hardirqs last enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78
[ 1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80
[ 1.154893] softirqs last enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564
[ 1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140
[ 1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[ 1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[ 1.154917] Workqueue: events deferred_probe_work_func
[ 1.154923] Call trace:
[ 1.154928] dump_backtrace+0x0/0x190
[ 1.154933] show_stack+0x14/0x20
[ 1.154940] dump_stack+0xe0/0x148
[ 1.154946] ___might_sleep+0x150/0x1f0
[ 1.154952] __might_sleep+0x4c/0x80
[ 1.154957] wait_for_completion_timeout+0x40/0x140
[ 1.154964] ti_sci_set_device_state+0xa0/0x158
[ 1.154969] ti_sci_cmd_get_device_exclusive+0x14/0x20
[ 1.154977] ti_sci_dev_start+0x34/0x50
[ 1.154984] genpd_runtime_resume+0x78/0x1f8
[ 1.154991] __rpm_callback+0x3c/0x140
[ 1.154996] rpm_callback+0x20/0x80
[ 1.155001] rpm_resume+0x568/0x758
[ 1.155007] __pm_runtime_resume+0x44/0xb0
[ 1.155013] omap8250_probe+0x2b4/0x508
[ 1.155019] platform_drv_probe+0x50/0xa0
[ 1.155023] really_probe+0xd4/0x318
[ 1.155028] driver_probe_device+0x54/0xe8
[ 1.155033] __device_attach_driver+0x80/0xb8
[ 1.155039] bus_for_each_drv+0x74/0xc0
[ 1.155044] __device_attach+0xdc/0x138
[ 1.155049] device_initial_probe+0x10/0x18
[ 1.155053] bus_probe_device+0x98/0xa0
[ 1.155058] deferred_probe_work_func+0x74/0xb0
[ 1.155063] process_one_work+0x280/0x6e8
[ 1.155068] worker_thread+0x48/0x430
[ 1.155073] kthread+0x108/0x138
[ 1.155079] ret_from_fork+0x10/0x18
To fix the bug we need to first call pm_runtime_enable() prior to any
pm_runtime calls.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ]
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4cbd7814bbd595061fcb6d6355d63f04179161cd ]
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream.
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
Subsystem: 17aa:5082
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 82
IOMMU group: 11
Region 0: I/O ports at 2200 [size=256]
Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]
Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 975efc66d4e654207c17f939eb737ac591ac38fe ]
When booting with heavily modularized config, the serial console
may not be able to load until after init when modules that
satisfy needed dependencies have time to load.
Unfortunately, as qcom_geni_console_setup is marked as __init,
the function may have been freed before we get to run it,
causing boot time crashes such as:
[ 6.469057] Unable to handle kernel paging request at virtual address ffffffe645d4e6cc
[ 6.481623] Mem abort info:
[ 6.484466] ESR = 0x86000007
[ 6.487557] EC = 0x21: IABT (current EL), IL = 32 bits
[ 6.492929] SET = 0, FnV = 0g
[ 6.496016] EA = 0, S1PTW = 0
[ 6.499202] swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000008151e000
[ 6.501286] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[ 6.505977] [ffffffe645d4e6cc] pgd=000000017df9f003, p4d=000000017df9f003, pud=000000017df9f003, pmd=000000017df9c003, pte=0000000000000000
[ 6.505990] Internal error: Oops: 86000007 [#1] PREEMPT SMP
[ 6.505995] Modules linked in: zl10353 zl10039 zl10036 zd1301_demod xc5000 xc4000 ves1x93 ves1820 tuner_xc2028 tuner_simple tuner_types tua9001 tua6100 1
[ 6.506152] isl6405
[ 6.518104] ufshcd-qcom 1d84000.ufshc: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[ 6.530549] horus3a helene fc2580 fc0013 fc0012 fc0011 ec100 e4000 dvb_pll ds3000 drxk drxd drx39xyj dib9000 dib8000 dib7000p dib7000m dib3000mc dibx003
[ 6.624271] CPU: 7 PID: 148 Comm: kworker/7:2 Tainted: G W 5.8.0-mainline-12021-g6defd37ba1cd #3455
[ 6.624273] Hardware name: Thundercomm Dragonboard 845c (DT)
[ 6.624290] Workqueue: events deferred_probe_work_func
[ 6.624296] pstate: 40c00005 (nZcv daif +PAN +UAO BTYPE=--)
[ 6.624307] pc : qcom_geni_console_setup+0x0/0x110
[ 6.624316] lr : try_enable_new_console+0xa0/0x140
[ 6.624318] sp : ffffffc010843a30
[ 6.624320] x29: ffffffc010843a30 x28: ffffffe645c3e7d0
[ 6.624325] x27: ffffff80f8022180 x26: ffffffc010843b28
[ 6.637937] x25: 0000000000000000 x24: ffffffe6462a2000
[ 6.637941] x23: ffffffe646398000 x22: 0000000000000000
[ 6.637945] x21: 0000000000000000 x20: ffffffe6462a5ce8
[ 6.637952] x19: ffffffe646398e38 x18: ffffffffffffffff
[ 6.680296] x17: 0000000000000000 x16: ffffffe64492b900
[ 6.680300] x15: ffffffe6461e9d08 x14: 69202930203d2064
[ 6.680305] x13: 7561625f65736162 x12: 202c363331203d20
[ 6.696434] x11: 0000000000000030 x10: 0101010101010101
[ 6.696438] x9 : 4d4d20746120304d x8 : 7f7f7f7f7f7f7f7f
[ 6.707249] x7 : feff4c524c787373 x6 : 0000000000008080
[ 6.707253] x5 : 0000000000000000 x4 : 8080000000000000
[ 6.707257] x3 : 0000000000000000 x2 : ffffffe645d4e6cc
[ 6.744223] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34)
[ 6.744966] x1 : fffffffefe74e174 x0 : ffffffe6462a5ce8
[ 6.753580] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34)
[ 6.761634] Call trace:
[ 6.761639] qcom_geni_console_setup+0x0/0x110
[ 6.761645] register_console+0x29c/0x2f8
[ 6.767981] Bluetooth: hci0: Frame reassembly failed (-84)
[ 6.775252] uart_add_one_port+0x438/0x500
[ 6.775258] qcom_geni_serial_probe+0x2c4/0x4a8
[ 6.775266] platform_drv_probe+0x58/0xa8
[ 6.855359] really_probe+0xec/0x398
[ 6.855362] driver_probe_device+0x5c/0xb8
[ 6.855367] __device_attach_driver+0x98/0xb8
[ 7.184945] bus_for_each_drv+0x74/0xd8
[ 7.188825] __device_attach+0xec/0x148
[ 7.192705] device_initial_probe+0x24/0x30
[ 7.196937] bus_probe_device+0x9c/0xa8
[ 7.200816] deferred_probe_work_func+0x7c/0xb8
[ 7.205398] process_one_work+0x20c/0x4b0
[ 7.209456] worker_thread+0x48/0x460
[ 7.213157] kthread+0x14c/0x158
[ 7.216432] ret_from_fork+0x10/0x18
[ 7.220049] Code: bad PC value
[ 7.223139] ---[ end trace 73f3b21e251d5a70 ]---
Thus this patch removes the __init avoiding crash in such
configs.
Cc: Andy Gross <agross@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Suggested-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200811025044.70626-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream.
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain #1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain #2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6b9e95dde7b54e6a53c47241201ab5a4035c320 upstream.
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fdf16d78941b4f380753053d229955baddd00712 upstream.
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096dd ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89efbe70b27dd325d8a8c177743a26b885f7faec upstream.
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27afac93e3bd7fa89749cf11da5d86ac9cde4dba upstream.
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f12e ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f12e ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c6c378b0cbe0c9f1390986b5f8ffb5f6ff7593b upstream.
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc5269ca765057a1b762e79a1cfd267cd7bf1c46 upstream.
vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl
to save struct vc_data values that are modified and restore the original
values in case of error.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/1596213192-6635-2-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8d1653daec02315e06d30246cff4af72e76e54e upstream.
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
[1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3
Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce684552a266cb1c7cc2f7e623f38567adec6653 upstream.
syzbot is reporting general protection fault in do_con_write() [1] caused
by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0
caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by
fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for
gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate()
from con_install() from tty_init_dev() from tty_open() on such console
causes vc->vc_pos == 0x10000000e due to
((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1).
I don't think that a console with 0 column or 0 row makes sense. And it
seems that vc_do_resize() does not intend to allow resizing a console to
0 column or 0 row due to
new_cols = (cols ? cols : vc->vc_cols);
new_rows = (lines ? lines : vc->vc_rows);
exception.
Theoretically, cols and rows can be any range as long as
0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g.
cols == 1048576 && rows == 2 is possible) because of
vc->vc_size_row = vc->vc_cols << 1;
vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row;
in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate().
Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in
visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return
an error, and con_write() will not be called on a console with 0 column
or 0 row.
We need to make sure that integer overflow in visual_init() won't happen.
Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying
1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate()
will be practically fine.
This patch does not touch con_init(), for returning -EINVAL there
does not help when we are not returning -ENOMEM.
[1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8
Reported-and-tested-by: syzbot <syzbot+017265e8553724e514e8@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200712111013.11881-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 551e553f0d4ab623e2a6f424ab5834f9c7b5229c upstream.
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4c23a140d80ef5e6d3d1f8f57007649014b60fa upstream.
I got null-ptr-deref in serial8250_start_tx():
[ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 78.123778] Mem abort info:
[ 78.126560] ESR = 0x86000007
[ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits
[ 78.134891] SET = 0, FnV = 0
[ 78.137933] EA = 0, S1PTW = 0
[ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600
[ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000
[ 78.160029] Internal error: Oops: 86000007 [#1] SMP
[ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd
[ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48
[ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020
[ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--)
[ 78.228435] pc : 0x0
[ 78.230618] lr : serial8250_start_tx+0x160/0x260
[ 78.235215] sp : ffff800062eefb80
[ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff
[ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000
[ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000
[ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002
[ 78.259679] x21: 0000000000000001 x20: 0000000000000000
[ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000
[ 78.270259] x17: 0000000000000000 x16: 0000000000000000
[ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6
[ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539
[ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0
[ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88
[ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000
[ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8
[ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002
[ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8
[ 78.317873] Call trace:
[ 78.320312] 0x0
[ 78.322147] __uart_start.isra.9+0x64/0x78
[ 78.326229] uart_start+0xb8/0x1c8
[ 78.329620] uart_flush_chars+0x24/0x30
[ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30
[ 78.338128] n_tty_receive_buf+0x44/0x2c8
[ 78.342122] tty_ioctl+0x348/0x11f8
[ 78.345599] ksys_ioctl+0xd8/0xf8
[ 78.348903] __arm64_sys_ioctl+0x2c/0xc8
[ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0
[ 78.357583] do_el0_svc+0x44/0xd0
[ 78.360887] el0_sync_handler+0x14c/0x1d0
[ 78.364880] el0_sync+0x140/0x180
[ 78.368185] Code: bad PC value
SERIAL_PORT_DFNS is not defined on each arch, if it's not defined,
serial8250_set_defaults() won't be called in serial8250_isa_init_ports(),
so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref.
Fix this problem by calling serial8250_set_defaults() after init uart port.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b374c562ee7ab3f3a1daf959c01868bae761571c upstream.
Commit 33ae787b74fc ("serial: tegra: add support to ignore read") added
support for dropping input in case CREAD isn't set, but for PIO the
ignore_status_mask wasn't checked until after the character had been
put in the receive buffer.
Note that the NULL tty-port test is bogus and will be removed by a
follow-on patch.
Fixes: 33ae787b74fc ("serial: tegra: add support to ignore read")
Cc: stable <stable@vger.kernel.org> # 5.4
Cc: Shardar Shariff Md <smohammed@nvidia.com>
Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22a82fa7d6c3e16d56a036b1fa697a39b954adf0 upstream.
The problems started with the revert (18cc7ac8a28e28). The
cdns_uart_console.index is statically assigned -1. When the port is
registered, Linux assigns consecutive numbers to it. It turned out that
when using ttyPS1 as console, the index is not updated as we are reusing
the same cdns_uart_console instance for multiple ports. When registering
ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it
already is 0 and not updated.
That led to 2ae11c46d5fdc4. It assigns the index prior to registering
the uart_driver once. Unfortunately, that ended up breaking the
situation where the probe order does not match the id order. When using
the same device tree for both uboot and linux, it is important that the
serial0 alias points to the console. So some boards reverse those
aliases. This was reported by Jan Kiszka. The proposed fix was reverting
the index assignment and going back to the previous iteration.
However such a reversed assignement (serial0 -> uart1, serial1 -> uart0)
was already partially broken by the revert (18cc7ac8a28e28). While the
ttyPS device works, the kmsg connection is already broken and kernel
messages go missing. Reverting the id assignment does not fix this.
>From the xilinx_uartps driver pov (after reverting the refactoring
commits), there can be only one console. This manifests in static
variables console_pprt and cdns_uart_console. These variables are not
properly linked and can go out of sync. The cdns_uart_console.index is
important for uart_add_one_port. We call that function for each port -
one of which hopefully is the console. If it isn't, the CON_ENABLED flag
is not set and console_port is cleared. The next cdns_uart_probe call
then tries to register the next port using that same cdns_uart_console.
It is important that console_port and cdns_uart_console (and its index
in particular) stay in sync. The index assignment implemented by
Shubhrajyoti Datta is correct in principle. It just may have to happen a
second time if the first cdns_uart_probe call didn't encounter the
console device. And we shouldn't change the index once the console uart
is registered.
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/
Fixes: 18cc7ac8a28e28 ("Revert "serial: uartps: Register own uart console and driver structures"")
Fixes: 2ae11c46d5fdc4 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Fixes: 76ed2e10579671 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5fdbe136ae19ab751daaa4d08d9a42f3e30d17f9 ]
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d8edf8eb5f6e921fe6389f96d2cd05862730a6ff upstream.
This driver calls ioremap() in probe, but it misses calling iounmap() in
probe's error handler and remove.
Add the missed calls to fix it.
Fixes: 47d37d6f94cc ("serial: Add auart driver for i.MX23/28")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200709135608.68290-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76ed2e105796710cf5b8a4ba43c81eceed948b70 upstream.
This reverts commit 2ae11c46d5fdc46cb396e35911c713d271056d35.
It turned out to break the ultra96-rev1, e.g., which uses uart1 as
serial0 (and stdout-path = "serial0:115200n8").
Fixes: 2ae11c46d5fd ("tty: xilinx_uartps: Fix missing id assignment to the console")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf9c94456ebafc6d75a834e58dfdc8ae71a3acbc upstream.
This reverts commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe.
In discussion on the mailing list, it has been determined that this is
not the correct type of fix for this issue. Revert it so that we can do
this correctly.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Cc: Raghavendra Rao Ananta <rananta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4dd31f1ffec6c370c3c2e0c605628bf5e16d5c46 ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01dbb362f0a114fbce19c8abe4cd6f4710e934d5 ]
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84d6f81c1fb58b56eba81ff0a36cf31946064b40 ]
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8508f4cba308f785b2fd4b8c38849c117b407297 ]
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe ]
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b668c064ec33f3d687c3a413d05e355172e6c92 ]
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf14 ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e0a851fe6b9b619527bd928aa93caaddd003f70c upstream.
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a28 ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a28.
Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 62a7f3009a460001eb46984395280dd900bc4ef4 ]
Move the IDs to pci_ids.h so it can be used by next patch.
Link: https://lore.kernel.org/r/20200508065343.32751-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68e55f61c13842baf825958129698c5371db432c ]
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 24eb2377f977fe06d84fca558f891f95bc28a449 upstream.
hvc_open sets tty->driver_data to NULL when open fails at some point.
Typically, the failure happens in hp->ops->notifier_add(). If there is
a racing process which tries to open such mangled tty, which was not
closed yet, the process will crash in hvc_open as tty->driver_data is
NULL.
All this happens because close wants to know whether open failed or not.
But ->open should not NULL this and other tty fields for ->close to be
happy. ->open should call tty_port_set_initialized(true) and close
should check by tty_port_initialized() instead. So do this properly in
this driver.
So this patch removes these from ->open:
* tty_port_tty_set(&hp->port, NULL). This happens on last close.
* tty->driver_data = NULL. Dtto.
* tty_port_put(&hp->port). This happens in shutdown and until now, this
must have been causing a reference underflow, if I am not missing
something.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Raghavendra <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200526145632.13879-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b86dab054059b970111b5516ae548efaae5b3aae upstream.
When k_ascii is invoked several times in a row there is a potential for
signed integer overflow:
UBSAN: Undefined behaviour in drivers/tty/vt/keyboard.c:888:19 signed integer overflow:
10 * 1111111111 cannot be represented in type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.11 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
ubsan_epilogue+0xe/0x30 lib/ubsan.c:154
handle_overflow+0xdc/0xf0 lib/ubsan.c:184
__ubsan_handle_mul_overflow+0x2a/0x40 lib/ubsan.c:205
k_ascii+0xbf/0xd0 drivers/tty/vt/keyboard.c:888
kbd_keycode drivers/tty/vt/keyboard.c:1477 [inline]
kbd_event+0x888/0x3be0 drivers/tty/vt/keyboard.c:1495
While it can be worked around by using check_mul_overflow()/
check_add_overflow(), it is better to introduce a separate flag to
signal that number pad is being used to compose a symbol, and
change type of the accumulator from signed to unsigned, thus
avoiding undefined behavior when it overflows.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200525232740.GA262061@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17b4efdf4e4867079012a48ca10d965fe9d68822 upstream.
An uninitialised spin lock for sifive serial console raises a bad
magic spin_lock error as reported and discussed here [1].
Initialising the spin lock resolves the issue.
The fix is tested on HiFive Unleashed A00 board with Linux 5.7-rc4
and OpenSBI v0.7
[1] https://lore.kernel.org/linux-riscv/b9fe49483a903f404e7acc15a6efbef756db28ae.camel@wdc.com
Fixes: 45c054d0815b ("tty: serial: add driver for the SiFive UART")
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1589019852-21505-2-git-send-email-sagar.kadam@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2ae11c46d5fdc46cb396e35911c713d271056d35 ]
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a28e ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a28e ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 57d38f26d81e4275748b69372f31df545dcd9b71 ]
By directly using kfree() in different places we risk missing one if
it is switched to using vfree(), especially if the corresponding
vmalloc() is hidden away within a common abstraction.
Oh wait, that's exactly what happened here.
So let's fix this by creating a common abstraction for the free case
as well.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-by: syzbot+0bfda3ade1ee9288a1be@syzkaller.appspotmail.com
Fixes: 9a98e7a80f95 ("vt: don't use kmalloc() for the unicode screen buffer")
Cc: <stable@vger.kernel.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2005021043110.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 18cc7ac8a28e28cd005c2475f52576cfe10cabfb upstream.
This reverts commit 024ca329bfb9a948f76eaff3243e21b7e70182f2.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1ee35667e36a8efddee381df5fe495ad65f4d15c.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 492cc08bc16c44e2e587362ada3f6269dee2be22 upstream.
This reverts commit bed25ac0e2b6ab8f9aed2d20bc9c3a2037311800.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/eb0ec98fecdca9b79c1a3ac0c30c668b6973b193.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Peter Zijlstra
Paras Sharma
Peng Fan
Tong Zhang
Artem Savkov
Tyrel Datwyler
Jonathan Bakker
Wei Yongjun
Raviteja Narayanam
Vignesh Raghavendra
Peter Ujfalusi
Palmer Dabbelt
Tobias Diedrich
John Stultz
Sergey Senozhatsky
Valmer Huhn
Holger Assmann
Lukas Wunner
Tamseel Shams
George Kennedy
Tetsuo Handa
Serge Semin
Yang Yingliang
Johan Hovold
Helmut Grohne
Matthew Howell
Chuhong Yuan
Jan Kiszka
Greg Kroah-Hartman
Gregory CLEMENT
Raghavendra Rao Ananta
Kai-Heng Feng
Douglas Anderson
Jiri Slaby
Dmitry Torokhov
Sagar Shrikant Kadam
Shubhrajyoti Datta
Nicolas Pitre
Michal Simek