| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit a7083763619f7485ccdade160deb81737cf2732f ]
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 986b5094708e508baa452a23ffe809870934a7df ]
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
Fixes: a38045121bf4 ("soc/tegra: pmc: Add generic PM domain support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
|
|
The FUSE clock should be enabled during suspend on Tegra124. Currently
clk driver enables it on all SoCs, but FUSE may require a higher core
voltage on Tegra30 while enabled. Move the quirk into the FUSE driver
and make it specific to Tegra124.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra FUSE belongs to the core power domain and we're going to enable
GENPD support for the core domain. Now FUSE device must be resumed using
runtime PM API in order to initialize the FUSE power state. Add runtime PM
support to the FUSE driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The fuse->clk must be cleared if FUSE driver fails to probe, otherwise
tegra_fuse_readl() will crash. It's unlikely to happen in practice,
nevertheless let's correct it for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Both PMC and cpuidle drivers are probed at the same init level and
cpuidle depends on the PMC suspend mode. Add new default suspend mode
that indicates whether PMC driver has been probed and reset the mode in
a case of deferred probe of the PMC driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Remove including <linux/version.h> that don't need it.
V1->V2: Split the patch in two
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The regulator coupler drivers now use regulator-driver API function that
isn't available during compile-testing. Make regulator coupler drivers
dependent on CONFIG_REGULATOR in Kconfig.
Fixes: 03978d42ed0d ("soc/tegra: regulators: Bump voltages on system reboot")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
|
|
The tegra30_fuse_read() symbol is used on Tegra234, so make sure it's
available.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
fuse->base can not be unmapped if allocate lookups failed in
tegra_init_fuse(), because it is an early_initcall, the driver
will be loaded anyway and fuse->base will be accessed by other
functions later, so remove the return -ENOMEM after allocating
lookups failed to make less confusing.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
[treding@nvidia.com: drop error message, out-of-memory is noisy anyway]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The core voltage shall not drop until state of core domain is synced,
i.e. all device drivers that use core domain are loaded and ready.
Support core domain state syncing. The core domain driver invokes the
core-regulator voltage syncing once the state of domain is synced, at
this point the core voltage is allowed to go lower than the level left
after bootloader.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add driver state syncing that is invoked once all PMC consumers are
attached and ready. The consumers are the power domain clients.
The synchronization callback is invoked once all client drivers are
probed, the driver core handles this for us. This callback informs
PMC driver that all voltage votes are initialized by each PD client
and it's safe to begin voltage scaling of the core power domain.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash DT backwards-compatibility patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
NVIDIA Tegra SoCs have multiple power domains, each domain corresponds
to an external SoC power rail. Core power domain covers vast majority of
hardware blocks within a Tegra SoC. The voltage of a power domain should
be set to a level which satisfies all devices within the power domain.
Add support for the core power domain which controls voltage state of the
domain. This allows us to support system-wide DVFS on Tegra20-210 SoCs.
The PMC powergate domains now are sub-domains of the core domain, this
requires device-tree updating, older DTBs are unaffected and will continue
to work as before.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash lockdep class removal patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add stubs needed for compile-testing of Tegra memory drivers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add common helper which initializes OPP table for Tegra SoC core devices.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Ensure that SoC voltages are at a level suitable for a system reboot.
This is important for some devices that use CPU reset method for the
rebooting. SoC CPU and core voltages now are be restored to a level
that is suitable for rebooting. This patch fixes hang on reboot on
Asus Transformer TF101, it was also reported as fixing some of reboot
issues on Toshiba AC100.
Reported-by: Nikola Milosavljević <mnidza@outlook.com>
Tested-by: Nikola Milosavljević <mnidza@outlook.com> # TF101
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is a lot going on!
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the device
tree. The device tree is a functional programming language and does
not imply any order, so the right thing is for the pin control core
to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to go
in and select functions for a pin manually (iteratively, at the
prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver making
use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for MIPS
Broadcom devices to instead use the pin control subsystem. New pin
control drivers for BCM6345, BCM6328, BCM6358, BCM6362, BCM6368,
BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B
in the Qualcomm PMIC GPIO driver. Also the two GPIOs on PM8008 are
supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic fixes
for the behaviour of the Ingenic pin controller. Add DMIC pins for
JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls"
* tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: Add Xilinx ZynqMP pinctrl driver support
firmware: xilinx: Add pinctrl support
pinctrl: rockchip: do coding style for mux route struct
pinctrl: Add PIN_CONFIG_MODE_PWM to enum pin_config_param
pinctrl: Introduce MODE group in enum pin_config_param
pinctrl: Keep enum pin_config_param ordered by name
dt-bindings: pinctrl: Add binding for ZynqMP pinctrl driver
pinctrl: core: Fix kernel doc string for pin_get_name()
pinctrl: mediatek: use spin lock in mtk_rmw
pinctrl: add drive for I2C related pins on MT8195
pinctrl: add pinctrl driver on mt8195
dt-bindings: pinctrl: mt8195: add pinctrl file and binding document
pinctrl: Ingenic: Add pinctrl driver for X2000.
pinctrl: Ingenic: Add pinctrl driver for JZ4775.
pinctrl: Ingenic: Add pinctrl driver for JZ4755.
pinctrl: Ingenic: Add pinctrl driver for JZ4750.
pinctrl: Ingenic: Add pinctrl driver for JZ4730.
dt-bindings: pinctrl: Add bindings for new Ingenic SoCs.
pinctrl: Ingenic: Reformat the code.
pinctrl: Ingenic: Add DMIC pins support for Ingenic SoCs.
...
|
|
Better to have a MODE group of settings to keep them together
when ordered alphabetically. Hence, rename PIN_CONFIG_LOW_POWER_MODE
to PIN_CONFIG_MODE_LOW_POWER.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210412140741.39946-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Print out domain name when reset fails to acquire for debugging purposes
and to make formatting of GENPD errors consistent in the driver.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Switch all clocks of a power domain to a safe rate which is suitable
for all possible voltages in order to ensure that hardware constraints
aren't violated when power domain state toggles.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SW-initiated power gate toggling is dropped by PMC if there is
contention with a HW-initiated toggling, i.e. when one of CPU cores is
gated by cpuidle driver. Software should retry the toggling after 10
microseconds on Tegra20/30 SoCs, hence add the retrying. On Tegra114+ the
toggling method was changed in hardware, the TOGGLE_START bit indicates
whether PMC is busy or could accept the command to toggle, hence handle
that bit properly.
The problem pops up after enabling dynamic power gating of 3D hardware,
where 3D power domain fails to turn on/off "randomly".
The programming sequence and quirks are documented in TRMs, but PMC
driver obliviously re-used the Tegra20 logic for Tegra30+, which strikes
back now. The 10 microseconds and other timeouts aren't documented in TRM,
they are taken from downstream kernel.
Link: https://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=commit;h=311dd1c318b70e93bcefec15456a10ff2b9eb0ff
Link: https://nv-tegra.nvidia.com/gitweb/?p=linux-3.10.git;a=commit;h=7f36693c47cb23730a6b2822e0975be65fb0c51d
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The tegra_powergate_power_up() has a typo in the error code path where it
will try to disable clocks twice, fix it. In practice that error never
happens, so this is a minor correction.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fix voltage coupler lockup which happens when voltage-spread is out
of range due to a bug in the code. The max-spread requirement shall be
accounted when CPU regulator doesn't have consumers. This problem is
observed on Tegra30 Ouya game console once system-wide DVFS is enabled
in a device-tree.
Fixes: 783807436f36 ("soc/tegra: regulators: Add regulators coupler for Tegra30")
Cc: stable@vger.kernel.org
Reported-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This commit implements a register map which grants USB (UTMI and HSIC)
sleepwalk registers access to USB PHY drivers. The USB sleepwalk logic
is in PMC hardware block but USB PHY drivers have the best knowledge
of proper programming sequence.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.11-rc1
This contains a couple of warning fixes and a fix for a mostly harmless
bug in the process ID retrieval code.
* tag 'tegra-for-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix index bug in get_process_id
soc: tegra: fuse: speedo-tegra210: Remove a group of set but unused variables
soc: tegra: fuse: speedo-tegra124: Remove some set but unused variables
Link: https://lore.kernel.org/r/20201127144329.124891-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch simply fixes a bug of referencing speedos[num] in every
for-loop iteration in get_process_id function.
Fixes: 0dc5a0d83675 ("soc/tegra: fuse: Add Tegra210 support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/tegra/fuse/speedo-tegra210.c: In function ‘tegra210_init_speedo_data’:
drivers/soc/tegra/fuse/speedo-tegra210.c:105:56: warning: variable ‘soc_iddq’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra210.c:105:46: warning: variable ‘gpu_iddq’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra210.c:105:36: warning: variable ‘cpu_iddq’ set but not used [-Wunused-but-set-variable]
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[treding@nvidia.com: remove unnecessary reads altogether]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/tegra/fuse/speedo-tegra124.c: In function ‘tegra124_init_speedo_data’:
drivers/soc/tegra/fuse/speedo-tegra124.c:105:38: warning: variable ‘soc_iddq_value’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra124.c:105:22: warning: variable ‘gpu_iddq_value’ set but not used [-Wunused-but-set-variable]
drivers/soc/tegra/fuse/speedo-tegra124.c:105:6: warning: variable ‘cpu_iddq_value’ set but not used [-Wunused-but-set-variable]
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[treding@nvidia.com: remove unnecessary reads altogether]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The tegra_read_ram_code() is used by EMC drivers and we're going to make
these driver modular, hence this function needs to be exported.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-3-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Pull ARM Devicetree updates from Olof Johansson:
"As usual, most of the changes are to devicetrees.
Besides smaller fixes, some refactorings and cleanups, some of the new
platforms and chips (or significant features) supported are below:
Broadcom boards:
- Cisco Meraki MR32 (BCM53016-based)
- BCM2711 (RPi4) display pipeline support
Actions Semi boards:
- Caninos Loucos Labrador SBC (S500-based)
- RoseapplePi SBC (S500-based)
Allwinner SoCs/boards:
- A100 SoC with Perf1 board
- Mali, DMA, Cetrus and IR support for R40 SoC
Amlogic boards:
- Libretch S905x CC V2 board
- Hardkernel ODROID-N2+ board
Aspeed boards/platforms:
- Wistron Mowgli (AST2500-based, Power9 OpenPower server)
- Facebook Wedge400 (AST2500-based, ToR switch)
Hisilicon SoC:
- SD5203 SoC
Nvidia boards:
- Tegra234 VDK, for pre-silicon Orin SoC
NXP i.MX boards:
- Librem 5 phone
- i.MX8MM DDR4 EVK
- Variscite VAR-SOM-MX8MN SoM
- Symphony board
- Tolino Shine 2 HD
- TQMa6 SoM
- Y Soft IOTA Orion
Rockchip boards:
- NanoPi R2S board
- A95X-Z2 board
- more Rock-Pi4 variants
STM32 boards:
- Odyssey SOM board (STM32MP157CAC-based)
- DH DRC02 board
Toshiba SoCs/boards:
- Visconti SoC and TPMV7708 board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
ARM: dts: nspire: Fix SP804 users
arm64: dts: lg: Fix SP804 users
arm64: dts: lg: Fix SP805 clocks
ARM: mstar: Fix up the fallout from moving the dts/dtsi files
ARM: mstar: Add mstar prefix to all of the dtsi/dts files
ARM: mstar: Add interrupt to pm_uart
ARM: mstar: Add interrupt controller to base dtsi
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
arm64: dts: ti: k3-j7200-main: Add USB controller
arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
ARM: dts: hisilicon: add SD5203 dts
ARM: dts: hisilicon: fix the system controller compatible nodes
arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
arm64: dts: zynqmp: Remove undocumented u-boot properties
arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
|
|
The Tegra PMC driver does ungodly things with the interrupt hierarchy,
repeatedly corrupting it by pulling hwirq numbers out of thin air,
overriding existing IRQ mappings and changing the handling flow
of unsuspecting users.
All of this is done in the name of preserving the interrupt hierarchy
even when these levels do not exist in the HW. Together with the use
of proper IRQs for IPIs, this leads to an unbootable system as the
rescheduling IPI gets repeatedly repurposed for random drivers...
Instead, let's simply mark the level from which the hierarchy does
not make sense for the HW, and let the core code trim the usused
levels from the hierarchy.
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Make the PMC driver resistent to variable depth interrupt hierarchy,
which we are about to introduce.
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Changes for v5.10-rc1
This set of changes fixes some minor issues in existing device trees and
adds ID EEPROMs on the Jetson Xavier NX. All ID EEPROMs are now labelled
to allow them to be detected by software.
It also adds support for the Tegra234 VDK board, which is a pre-silicon
platform for the upcoming Orin SoC.
* tag 'tegra-for-5.10-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Initial Tegra234 VDK support
arm64: tegra: Populate EEPROMs for Jetson Xavier NX
arm64: tegra: Add label properties for EEPROMs
arm64: tegra: Add DT binding for AHUB components
arm64: tegra: Enable ACONNECT, ADMA and AGIC on Jetson Nano
arm64: tegra: Properly size register regions for GPU on Tegra194
arm64: tegra: Use valid PWM period for VDD_GPU on Tegra210
arm64: tegra: Describe display controller outputs for Tegra210
arm64: tegra: Disable SD card write-protection on Jetson Nano
arm64: tegra: Add VBUS supply for micro USB port on Jetson Nano
arm64: tegra: Wire up pinctrl states for all DPAUX controllers
arm64: tegra: Add ID EEPROMs on Jetson AGX Xavier
Link: https://lore.kernel.org/r/20200918150303.3938852-5-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The NVIDIA Tegra234 VDK is a simulation platform for the Orin SoC. It
supports a subset of the peripherals that will be available in the final
chip and serves as a bootstrapping platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PMC block is largely similar to that found on earlier chips, but
not completely compatible. Allow binding to the instantiation found on
Tegra234.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Move the definitions of reset sources and levels into a more natural
location.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The MISC block is largely similar to that found on earlier chips, but
not completely compatible. Allow binding to the instantiation found on
Tegra234.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support for FUSE block found on the Tegra234 SoC, which is largely
similar to the IP found on previous generations.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This function can be used by drivers to determine whether code is
running on silicon or on a simulation platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This function extracts the PRE_SI_PLATFORM field from the HIDREV
register and can be used to determine which platform the kernel runs on
(silicon, simulation, ...). Note that while only Tegra194 and later
define this field, it should be safe to call this on prior generations
as well since this field should read as 0, indicating silicon.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
The hardware block is called APB MISC, not ABP MISC, so fix the warning
to use the correct name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PMIC wake event can be used to bring the system out of suspend based
on certain events happening on the PMIC (such as an RTC alarm).
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PMIC wake event can be used to bring the system out of suspend based
on certain events happening on the PMIC (such as an RTC alarm).
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/soc/tegra/pmc.o: in function `pinconf_generic_dt_node_to_map_pin':
pmc.c:(.text+0x500): undefined reference to `pinconf_generic_dt_node_to_map'
armv7a-hardfloat-linux-gnueabi-ld: drivers/soc/tegra/pmc.o:(.rodata+0x1f88): undefined reference to `pinconf_generic_dt_free_map'
So SOC_TEGRA_PMC should select GENERIC_PINCONF.
Fixes: 4a37f11c8f57 ("soc/tegra: pmc: Implement pad configuration via pinctrl")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Currently the SoC revision attribute for Tegra devices displays the
value of the enum associated with a particular revision. This is not
very useful because to obtain the actual revision you need to
use the tegra_revision enumeration to translate the value.
It is more meaningful to display a name for the revision, such as
'A01', than the enumarated value and therefore, update the revision
attribute to display a name. This change does alter the ABI, which
is unfortunate, but this is more meaningful and maintable.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Clean-up the tegra_init_revision() function by removing the 'rev'
variable which is not needed and use the newly added helper function
tegra_get_minor_rev() to get the minor revision.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
Nathan Chancellor
Christophe JAILLET
Linus Torvalds
Dmitry Osipenko
Cai Huoqing
Thierry Reding
Yang Yingliang
Andy Shevchenko
JC Kuo
Arnd Bergmann
Nicolin Chen
Lee Jones
Marc Zyngier
Olof Johansson
Gustavo A. R. Silva
Jon Hunter
Corentin Labbe