| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit ca2ade24157693b4e533ccec69df00ef719d4aad ]
There are extraneous parantheses that are causing clang to produce a
warning so remove these.
Clean up 3 clang warnings:
equality comparison with extraneous parentheses [-Wparentheses-equality]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b0e87a6aafe12d75c2bea6fc8e49e88b98b3083 ]
The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable.
When it is detected, the right thing to do is to drop all connected and
disconnected commands. The code for that is already present so refactor it and
call it when SR_RST is set.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca694afad707cb3ae2fdef3b28454444d9ac726e ]
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08267216b3f8aa5adc204bdccf8deb72c1cd7665 ]
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",
... The reselected initiator shall then assert the BSY signal
within a selection abort time of its most recent detection of being
reselected; this is required for correct operation of the time-out
procedure.
The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45ddc1b24806cc8f1a09f23dd4e7b6e4a8ae36e1 ]
When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ef55f6744c45e3d7c85a3f74ada39b67ac741dd ]
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 070356513963be6196142acff56acc8359069fa1 ]
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise
some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or
DID_RESET just because sense data is missing.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c8ed783c2faa1e3f741844ffac41340338ea0f4 ]
This is mostly needed because an AztecMonster II target has been observed
disconnecting REQUEST SENSE commands and then failing to reselect properly.
Suggested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dad8261e643849ea134c7cd5c8e794e31d93b9eb ]
The return value is taken to mean "retry" or "don't retry". Change it to bool
to improve readability. Fix related comments. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1aeeeed7f03c576f096eede7b0384f99a98f588c ]
When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.
[mkp: adjusted Hannes' SoB address]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 32c850bf587f993b2620b91e5af8a64a7813f504 ]
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eebcc19646489b68399ce7b35d9c38eb9f4ec40f ]
Error paths in ufshcd_init() ufshcd_hba_exit() killed clk_scaling workqueue
when the workqueue is actually created quite late in ufshcd_init(). So, we
end up getting NULL pointer dereference in such error paths. Fix this by
moving clk_scaling initialization and kill codes to two separate methods, and
call them at required places.
Fixes: 401f1e4490ee ("scsi: ufs: don't suspend clock scaling during clock
gating")
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72349b62a571effd6faadd0600b8e657dd87afbf ]
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 76cb25b058034d37244be6aca97a2ad52a5fbcad ]
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 288315e95264b6355e26609e9dec5dc4563d4ab0 ]
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2879265f514b1f4154288243c91438ddbedb3ed4 ]
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aad59d5d34738d6fd8c359df8048a84cd443e504 ]
During attachment, the driver writes the EQ doorbell to disable potential
interrupts from an EQ. The current EQ doorbell format used for clearing the
interrupt is incorrect and uses an if_type=2 format, making the operation act
on the wrong EQ.
Correct the code to use the proper if_type=6 EQ doorbell format.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01a8aed6a009625282b6265880f6b20cbd7a9c70 ]
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3a03ee1102a44ccbd2c5de80a6e862ba23e9b55 ]
Current code relies on switch to provide a unique combination of WWPN +
NPORTID to tract an FC port. This patch tries to detect a case where switch
data base can get corrupted where multiple WWPNs can have the same Nport ID.
The 1st Nport ID on the list will be kept while the duplicate Nport ID will be
discarded.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 527b8ae3948bb59c13ebaa7d657ced56ea25ab05 ]
When FW rejects a command due to "entry_status" error (malform IOCB), the srb
resource needs to be returned back for cleanup. The filter to catch this is
in the wrong location.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d74c87a20adcc77b19753c315ad9c320b2288be ]
Clear port speed value on chip reset.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f99c5d294b3653e6ae563eaac5db5b4138afe31c ]
During adapter shutdown process check for register disconnect before
proceeding to call PCI functions.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8bccfe0d21b5adbba6ec4fe1776160b80d09f78a ]
Abort IOCB request can take up to 40s or 2 ABTS timeout. We will wait for
ABTS response for 20s. On a timeout, second ABTS can go out with another 20s
timeout. On 2nd ABTS timeout FW will automatically do Logout.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1073daa470d906f1853ed4b828f16e2350a5875c ]
Move ATIO queue processing out of hardware_lock to prevent deadlock.
Fixes: 3bb67df5b5f8 ("qla2xxx: Check for online flag instead of active reset when transmitting responses")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa9e6d7b9643fc50a88c7b7aa1e34be8dc032749 ]
When driver receive PLOGI/PRLI from FW, the WWPN value will be provided. If
it is not, then driver will terminate it. The WWPN allows driver to locate
the session or create a new session.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93eca6135183f7a71e36acd47655a085ed11bcdc ]
For target mode, any chip reset triggered before target mode is enabled will
be held off until user is ready to enable. This prevents the chip from
starting or running before it is intended.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d9bf0a9a268f7ca0b811d6e6a1fc783afa5c746 ]
When switch responds with error for Get Port Speed Command (GPSC), driver
should not proceed with telling FW about the speed of the remote port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 49cecca7dd49e2950ed6d973acfa84e7c8c7a480 ]
On Abort of initiator scsi command, the abort needs to follow the same qpair
as the the scsi command to prevent out of order processing.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9393c8de628cf0968d81a17cc11841e42191e041 upstream.
In scsi_mq_setup_tags(), cmd_size is calculated based on zero size for the
scatter-gather list in case the low level driver uses SG_NONE in its host
template.
cmd_size is passed on to the block layer for calculation of the request
size, and we've seen NULL pointer dereference errors from the block layer
in drivers where SG_NONE is used and a mq IO scheduler is active,
apparently as a consequence of this (see commit 68ab2d76e4be ("scsi:
cxlflash: Set sg_tablesize to 1 instead of SG_NONE"), and a recent patch by
Finn Thain converting the three m68k NFR5380 drivers to avoid setting
SG_NONE).
Try to avoid these errors by accounting for at least one sg list entry when
calculating cmd_size, regardless of whether the low level driver set a zero
sg_tablesize.
Tested on 030 m68k with the atari_scsi driver - setting sg_tablesize to
SG_NONE no longer results in a crash when loading this driver.
CC: Finn Thain <fthain@telegraphics.com.au>
Link: https://lore.kernel.org/r/1572922150-4358-1-git-send-email-schmitzmic@gmail.com
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d3566abb1a1e7772116e4d50fb6a58d19c9802e5 ]
In shutdown/reboot paths, the timer is not stopped:
qla2x00_shutdown
pci_device_shutdown
device_shutdown
kernel_restart_prepare
kernel_restart
sys_reboot
This causes lockups (on powerpc) when firmware config space access calls
are interrupted by smp_send_stop later in reboot.
Fixes: e30d1756480dc ("[SCSI] qla2xxx: Addition of shutdown callback handler.")
Link: https://lore.kernel.org/r/20191024063804.14538-1-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2ff2a36eff60efb5e123c940115216d6bf65684 ]
This patch fixes issue with Gen7 adapter in a blade environment where one
of the ports will not be detected by driver. Firmware expects mailbox 11 to
be set or cleared by driver for newer ISP.
Following message is seen in the log file:
[ 18.810892] qla2xxx [0000:d8:00.0]-1820:1: **** Failed=102 mb[0]=4005 mb[1]=37 mb[2]=20 mb[3]=8
[ 18.819596] cmd=2 ****
[mkp: typos]
Link: https://lore.kernel.org/r/20191022193643.7076-2-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fd103ccfe6a06e40e2d9d8c91d96332cc9e1239 ]
The initial lpfc_desc_set_adisc implementation in commit
dea3101e0a5c ("lpfc: add Emulex FC driver version 8.0.28") enabled ADISC if
cfg_use_adisc && RSCN_MODE && FCP_2_DEVICE
In commit 92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of
SLI-3") this changed to
(cfg_use_adisc && RSC_MODE) || FCP_2_DEVICE
and later in commit ffc954936b13 ("[SCSI] lpfc 8.3.13: FC Discovery Fixes
and enhancements.") to
(cfg_use_adisc && RSC_MODE) || (FCP_2_DEVICE && FCP_TARGET)
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: James Smart <james.smart@broadcom.com>
Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 66cf50e65b183c863825f5c28a818e3f47a72e40 ]
DRIVER_ERROR is a a driver byte setting, not a host byte. The qla2xxx
driver should rather return DID_ERROR here to be in line with the other
drivers.
Link: https://lore.kernel.org/r/20191018140458.108278-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8cbf0c173aa096dda526d1ccd66fc751c31da346 ]
When building a kernel with SCSI_SNI_53C710 enabled, Kconfig warns:
WARNING: unmet direct dependencies detected for 53C700_LE_ON_BE
Depends on [n]: SCSI_LOWLEVEL [=y] && SCSI [=y] && SCSI_LASI700 [=n]
Selected by [y]:
- SCSI_SNI_53C710 [=y] && SCSI_LOWLEVEL [=y] && SNI_RM [=y] && SCSI [=y]
Add the missing depends SCSI_SNI_53C710 to 53C700_LE_ON_BE to fix it.
Link: https://lore.kernel.org/r/20191009151128.32411-1-tbogendoerfer@suse.de
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ee6211408a8e939428f662833c7301394125b80 ]
Drop out memory dev_printk() with wrong device pointer argument.
[mkp: typo]
Link: https://lore.kernel.org/r/20191009151118.32350-1-tbogendoerfer@suse.de
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6ce6fb121a655aefe41dccc077141c102145a37 ]
Some arrays are not capable of returning RTPG data during state
transitioning, but rather return an 'LUN not accessible, asymmetric access
state transition' sense code. In these cases we can set the state to
'transitioning' directly and don't need to evaluate the RTPG data (which we
won't have anyway).
Link: https://lore.kernel.org/r/20191007135701.32389-1-hare@suse.de
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 35a79a63517981a8aea395497c548776347deda8 ]
alloc_workqueue is not checked for errors and as a result a potential
NULL dereference could occur.
Link: https://lore.kernel.org/r/1568824618-4366-1-git-send-email-allen.pais@oracle.com
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2a0fb340fcc816975b8b0f2fef913d11999c39cf ]
Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.
Fix the adjust for units for the completion timeout call.
[mkp: manual merge]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c4c91415a05677acc5c8131a5eb472d4aa96ae1 ]
Renumber one of the 0711 log messages so there isn't a duplication.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6a0990eaa768dfb7064f06777743acc6d392084b upstream.
Clearing ch->device in ch_release() is wrong because that pointer must
remain valid until ch_remove() is called. This patch fixes the following
crash the second time a ch device is opened:
BUG: kernel NULL pointer dereference, address: 0000000000000790
RIP: 0010:scsi_device_get+0x5/0x60
Call Trace:
ch_open+0x4c/0xa0 [ch]
chrdev_open+0xa2/0x1c0
do_dentry_open+0x13a/0x380
path_openat+0x591/0x1470
do_filp_open+0x91/0x100
do_sys_open+0x184/0x220
do_syscall_64+0x5f/0x1a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 085e56766f74 ("scsi: ch: add refcounting")
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191009173536.247889-1-bvanassche@acm.org
Reported-by: Rob Turk <robtu@rtist.nl>
Suggested-by: Rob Turk <robtu@rtist.nl>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77c301287ebae86cc71d03eb3806f271cb14da79 upstream.
We have a test case like block/001 in blktests, which will create a scsi
device by loading scsi_debug module and then try to delete the device by
sysfs interface. At the same time, it may remove the scsi_debug module.
And getting a invalid paging request BUG_ON as following:
[ 34.625854] BUG: unable to handle page fault for address: ffffffffa0016bb8
[ 34.629189] Oops: 0000 [#1] SMP PTI
[ 34.629618] CPU: 1 PID: 450 Comm: bash Tainted: G W 5.4.0-rc3+ #473
[ 34.632524] RIP: 0010:scsi_proc_hostdir_rm+0x5/0xa0
[ 34.643555] CR2: ffffffffa0016bb8 CR3: 000000012cd88000 CR4: 00000000000006e0
[ 34.644545] Call Trace:
[ 34.644907] scsi_host_dev_release+0x6b/0x1f0
[ 34.645511] device_release+0x74/0x110
[ 34.646046] kobject_put+0x116/0x390
[ 34.646559] put_device+0x17/0x30
[ 34.647041] scsi_target_dev_release+0x2b/0x40
[ 34.647652] device_release+0x74/0x110
[ 34.648186] kobject_put+0x116/0x390
[ 34.648691] put_device+0x17/0x30
[ 34.649157] scsi_device_dev_release_usercontext+0x2e8/0x360
[ 34.649953] execute_in_process_context+0x29/0x80
[ 34.650603] scsi_device_dev_release+0x20/0x30
[ 34.651221] device_release+0x74/0x110
[ 34.651732] kobject_put+0x116/0x390
[ 34.652230] sysfs_unbreak_active_protection+0x3f/0x50
[ 34.652935] sdev_store_delete.cold.4+0x71/0x8f
[ 34.653579] dev_attr_store+0x1b/0x40
[ 34.654103] sysfs_kf_write+0x3d/0x60
[ 34.654603] kernfs_fop_write+0x174/0x250
[ 34.655165] __vfs_write+0x1f/0x60
[ 34.655639] vfs_write+0xc7/0x280
[ 34.656117] ksys_write+0x6d/0x140
[ 34.656591] __x64_sys_write+0x1e/0x30
[ 34.657114] do_syscall_64+0xb1/0x400
[ 34.657627] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 34.658335] RIP: 0033:0x7f156f337130
During deleting scsi target, the scsi_debug module have been removed. Then,
sdebug_driver_template belonged to the module cannot be accessd, resulting
in scsi_proc_hostdir_rm() BUG_ON.
To fix the bug, we add scsi_device_get() in sdev_store_delete() to try to
increase refcount of module, avoiding the module been removed.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191015130556.18061-1-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f8fed0cdbbd6cdbf28d9ebe662f45765d2f7d39 upstream.
When a non-passthrough command is terminated with CHECK CONDITION, request
sense is executed by hijacking the command descriptor. Since
scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd() do not save/restore the
original command resid, the value returned on failure of the original
command is lost and replaced with the value set by the execution of the
request sense command. This value may in many instances be unaligned to the
device sector size, causing sd_done() to print a warning message about the
incorrect unaligned resid before the command is retried.
Fix this problem by saving the original command residual in struct
scsi_eh_save using scsi_eh_prep_cmnd() and restoring it in
scsi_eh_restore_cmnd(). In addition, to make sure that the request sense
command is executed with a correctly initialized command structure, also
reset the residual to 0 in scsi_eh_prep_cmnd() after saving the original
command value in struct scsi_eh_save.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191001074839.1994-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21e3d6c81179bbdfa279efc8de456c34b814cfd2 upstream.
I've got a report about a UAS drive enclosure reporting back Sense: Logical
unit access not authorized if the drive it holds is password protected.
While the drive is obviously unusable in that state as a mass storage
device, it still exists as a sd device and when the system is asked to
perform a suspend of the drive, it will be sent a SYNCHRONIZE CACHE. If
that fails due to password protection, the error must be ignored.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190903101840.16483-1-oneukum@suse.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c3b6a1d397420a0fdd97af2f06abfb78adc370df ]
There are instances, though rare, where a LOGO request cannot be sent out
and the thread in free session done can wait indefinitely. Fix this by
putting an upper bound to sleep.
Link: https://lore.kernel.org/r/20190912180918.6436-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70054aa39a013fa52eff432f2223b8bd5c0048f8 ]
For pci device, need to disable device when probe failed after enabled
device.
Link: https://lore.kernel.org/r/1567818450-173315-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f51913eef23f74c3bd07899dc7f1ed6df9e521d8 ]
In some cases, hba may go through shutdown flow without successful
initialization and then make system hang.
For example, if ufshcd_change_power_mode() gets error and leads to
ufshcd_hba_exit() to release resources of the host, future shutdown flow
may hang the system since the host register will be accessed in unpowered
state.
To solve this issue, simply add checking to skip shutdown for above kind of
situation.
Link: https://lore.kernel.org/r/1568780438-28753-1-git-send-email-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dccc96abfb21dc19d69e707c38c8ba439bba7160 ]
The data structure used for log messages is so large that it can cause a
boot failure. Since allocations from that data structure can fail anyway,
use kmalloc() / kfree() instead of that data structure.
See also https://bugzilla.kernel.org/show_bug.cgi?id=204119.
See also commit ded85c193a39 ("scsi: Implement per-cpu logging buffer") # v4.0.
Reported-by: Jan Palus <jpalus@fastmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jan Palus <jpalus@fastmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7e9e1fb7a9227be34ad4a5e778022c3164494cf ]
Implement .cleanup_rq() callback for freeing driver private part
of the request. Then we can avoid to leak this part if the request isn't
completed by SCSI, and freed by blk-mq or upper layer(such as dm-rq) finally.
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: <stable@vger.kernel.org>
Fixes: 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8b5292bcfcacf15182a77a973a98d310e76fd58b upstream.
Relogin fails to move forward due to scan_state flag indicating device is
not there. Before relogin process, Session delete process accidently
modified the scan_state flag.
[mkp: typos plus corrected Fixes: sha as reported by sfr]
Fixes: 2dee5521028c ("scsi: qla2xxx: Fix login state machine freeze")
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57adf5d4cfd3198aa480e7c94a101fc8c4e6109d upstream.
cdb in send_mode_select() is not zeroed and is only partially filled in
rdac_failover_get(), which leads to some random data getting to the
device. Users have reported storage responding to such commands with
INVALID FIELD IN CDB. Code before commit 327825574132 was not affected, as
it called blk_rq_set_block_pc().
Fix this by zeroing out the cdb first.
Identified & fix proposed by HPE.
Fixes: 327825574132 ("scsi_dh_rdac: switch to scsi_execute_req_flags()")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20190904155205.1666-1-martin.wilck@suse.com
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Ales Novak <alnovak@suse.cz>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Colin Ian King
Finn Thain
Hannes Reinecke
Jason Yan
Vivek Gautam
Deepak Ukey
George Kennedy
James Smart
Quinn Tran
Sawan Chandak
Michael Schmitz
Nicholas Piggin
Himanshu Madhani
Daniel Wagner
Thomas Bogendoerfer
Allen Pais
Bart Van Assche
Yufen Yu
Damien Le Moal
Oliver Neukum
Quinn Tran
Xiang Chen
Stanley Chu
Ming Lei
Martin Wilck