| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit d83ca3ea833d7a66d49225e4191c4e37cab8f079 ]
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d496b9a7246cb9813da1fe49e14edbbbf8e232d5 ]
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 036cad1f1ac9ce03e2db94b8460f98eaf1e1ee4c ]
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a25fa17b6ed6e6c8101e9c68a10ae68a9025f2c ]
During init, if pci_alloc_irq_vectors() fails, the driver has not yet setup
the IRQs. Fix the goto labels and error handling for this case.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9155cf30a3c4ef97e225d6daddf9bd4b173267e8 ]
In megasas_transition_to_ready() driver waits 180seconds for controller to
change FW state. Here we are calling msleep(1) in a loop for this. As
explained in timers-howto.txt, msleep(1) will actually sleep longer than
1ms. If a faulty controller is connected, we will end up waiting for much
more than 180 seconds causing unnecessary delays during load.
Change the granularity of msleep() call from 1ms to 1000ms.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97f35194093362a63b33caba2485521ddabe2c95 ]
Currently driver is modifying both current & NVRAM/persistent data in
Manufacturing page11. Driver should change only current copy of
Manufacturing page11. It should not modify the persistent data.
So removed the section of code where driver is modifying the persistent
data of Manufacturing page11.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6cd1bc7b9b5075d395ba0120923903873fc7ea0e ]
If EEDPTagMode field in manufacturing page11 is set then unset it. This is
needed to fix a hardware bug only in SAS3/SAS2 cards. So, skipping
EEDPTagMode changes in Manufacturing page11 for SAS 3.5 controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9029a72500b95578a35877a43473b82cb0386c53 ]
This is to fix SYNC CACHE and START STOP command failures with
DID_NO_CONNECT during driver unload.
In driver's IO submission patch (i.e. in driver's .queuecommand()) driver
won't allow any SCSI commands to the IOC when ioc->remove_host flag is set
and hence SYNC CACHE commands which are issued to the target drives (where
write cache is enabled) during driver unload time is failed with
DID_NO_CONNECT status.
Now modified the driver to allow SYNC CACHE and START STOP commands to IOC,
even when remove_host flag is set.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f4445bb93d82a984657b469e63118c2794a4c3d3 ]
There is a NULL pointer dereference in case *slot* happens to be NULL at
lines 1053 and 1878:
struct hisi_sas_cq *cq =
&hisi_hba->cq[slot->dlvry_queue];
Notice that *slot* is being NULL checked at lines 1057 and 1881:
if (slot), which implies it may be NULL.
Fix this by placing the declaration and definition of variable cq, which
contains the pointer dereference slot->dlvry_queue, after slot has been
properly NULL checked.
Addresses-Coverity-ID: 1474515 ("Dereference before null check")
Addresses-Coverity-ID: 1474520 ("Dereference before null check")
Fixes: 584f53fe5f52 ("scsi: hisi_sas: Fix the race between IO completion and timeout for SMP/internal IO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7ded0e8b0d11b6df1c4e5aa23a26e6629c21985 ]
The core driver, esp_scsi, does not use the ESP_CONFIG2_FENAB bit, so the
chip's Transfer Counter register is only 16 bits wide (not 24). A larger
transfer cannot work and will theoretically result in a failed command
and a "DMA length is zero" error.
Fixes: 3109e5ae0311 ("scsi: zorro_esp: New driver for Amiga Zorro NCR53C9x boards")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c404a68bf83b4135a8a9aa1c388ebdf98e8ba7f ]
We need to transfer device ownership to the CPU before we can manipulate
the mapped data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a5bd7021184dec2946f2a4d7a8943f8a5713e52 ]
We can't just transfer ownership to the CPU and then unmap, as this will
break with swiotlb.
Instead unmap the command and sense buffer a little earlier in the I/O
completion handler and get rid of the pci_dma_sync_sg_for_cpu call
entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 20054597f169090109fc3f0dfa1a48583f4178a4 ]
Clang warns when one enumerated type is implicitly converted to another.
drivers/scsi/iscsi_tcp.c:803:15: warning: implicit conversion from
enumeration type 'enum iscsi_host_param' to different enumeration type
'enum iscsi_param' [-Wenum-conversion]
&addr, param, buf);
^~~~~
1 warning generated.
iscsi_conn_get_addr_param handles ISCSI_HOST_PARAM_IPADDRESS just fine
so add an explicit cast to iscsi_param to make it clear to Clang that
this is expected behavior.
Link: https://github.com/ClangBuiltLinux/linux/issues/153
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 761c830ec7b3d0674b3ad89cefd77a692634e305 ]
Clang warns when one enumerated type is implicitly converted to another.
drivers/scsi/bfa/bfa_fcs_lport.c:379:26: warning: implicit conversion
from enumeration type 'enum bfa_lport_aen_event' to different
enumeration type 'enum bfa_ioc_aen_event' [-Wenum-conversion]
BFA_AEN_CAT_LPORT, event);
^~~~~
The root cause of these warnings is the bfad_im_post_vendor_event
function, which expects a value from enum bfa_ioc_aen_event but there
are multiple instances of values from enums bfa_port_aen_event,
bfa_audit_aen_event, and bfa_lport_aen_event being used in this
function.
Given that this doesn't appear to be a problem since cat helps with
differentiating the events, just change evt's type to int so that no
conversion needs to happen and Clang won't warn. Update aen_type's type
in bfa_aen_entry_s as members that hold enumerated types should be int.
Link: https://github.com/ClangBuiltLinux/linux/issues/147
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 362b5da3dfceada6e74ecdd7af3991bbe42c0c0f ]
Clang warns when an enumerated type is implicitly converted to another.
drivers/scsi/isci/request.c:3476:13: warning: implicit conversion from
enumeration type 'enum sci_task_status' to different enumeration type
'enum sci_status' [-Wenum-conversion]
status = sci_controller_start_task(ihost,
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/isci/host.c:2744:10: warning: implicit conversion from
enumeration type 'enum sci_status' to different enumeration type 'enum
sci_task_status' [-Wenum-conversion]
return SCI_SUCCESS;
~~~~~~ ^~~~~~~~~~~
drivers/scsi/isci/host.c:2753:9: warning: implicit conversion from
enumeration type 'enum sci_status' to different enumeration type 'enum
sci_task_status' [-Wenum-conversion]
return status;
~~~~~~ ^~~~~~
Avoid all of these implicit conversion by just making
sci_controller_start_task use sci_status. This silences
Clang and has no functional change since sci_task_status
has all of its values mapped to something in sci_status.
Link: https://github.com/ClangBuiltLinux/linux/issues/153
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9e9a103528c7e199ead6e5374c9c52cf16b5802 ]
Clang warns when one enumerated type is implicitly converted to another.
drivers/scsi/isci/request.c:1629:13: warning: implicit conversion from
enumeration type 'enum sci_io_status' to different enumeration type
'enum sci_status' [-Wenum-conversion]
status = SCI_IO_FAILURE_RESPONSE_VALID;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/isci/request.c:1631:12: warning: implicit conversion from
enumeration type 'enum sci_io_status' to different enumeration type
'enum sci_status' [-Wenum-conversion]
status = SCI_IO_FAILURE_RESPONSE_VALID;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
status is of type sci_status but SCI_IO_FAILURE_RESPONSE_VALID is of
type sci_io_status. Use SCI_FAILURE_IO_RESPONSE_VALID, which is from
sci_status and has SCI_IO_FAILURE_RESPONSE_VALID's exact value since
that is what SCI_IO_FAILURE_RESPONSE_VALID is mapped to in the isci.h
file.
Link: https://github.com/ClangBuiltLinux/linux/issues/153
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d25ff7a544889bc4b749fda31778d6a18dddbcb ]
Add missing break statement in order to prevent the code from falling
through to case TEST_UNIT_READY.
Addresses-Coverity-ID: 1357338 ("Missing break in switch")
Suggested-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e178f3ecfcf91a258e832b0f0843a4cfd9059ac ]
If an SSP/SMP IO times out, it may be actually in reality be
simultaneously processing completion of the slot in
slot_complete_vx_hw().
Then if the slot is freed in slot_complete_vx_hw() (this IPTT is freed
and it may be re-used by other slot), and we may abort the wrong slot in
hisi_sas_abort_task().
So to solve the issue, free the slot after the check of
SAS_TASK_STATE_ABORTED in slot_complete_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
SMP/internal IO
[ Upstream commit 584f53fe5f529d877968c711a095923c1ed12307 ]
If SMP/internal IO times out, we will possibly free the task immediately.
However if the IO actually completes at the same time, the IO completion
may refer to task which has been freed.
So to solve the issue, flush the tasklet to finish IO completion before
free'ing slot/task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a54691f874ab29ec82f08bc6936866a3ccdaa91 ]
At directly attached situation, if the user modifies the sysfs interface
of maximum_linkrate and minimum_linkrate to renegotiate the linkrate
between SAS controller and target, the value of both files mentioned
above should have change to user setting after renegotiate is over, but
it remains unchanged.
To fix this bug, maximum_linkrate and minimum_linkrate will be directly
fed back to relevant sas_phy structure.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca2ade24157693b4e533ccec69df00ef719d4aad ]
There are extraneous parantheses that are causing clang to produce a
warning so remove these.
Clean up 3 clang warnings:
equality comparison with extraneous parentheses [-Wparentheses-equality]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b0e87a6aafe12d75c2bea6fc8e49e88b98b3083 ]
The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable.
When it is detected, the right thing to do is to drop all connected and
disconnected commands. The code for that is already present so refactor it and
call it when SR_RST is set.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca694afad707cb3ae2fdef3b28454444d9ac726e ]
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08267216b3f8aa5adc204bdccf8deb72c1cd7665 ]
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",
... The reselected initiator shall then assert the BSY signal
within a selection abort time of its most recent detection of being
reselected; this is required for correct operation of the time-out
procedure.
The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45ddc1b24806cc8f1a09f23dd4e7b6e4a8ae36e1 ]
When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ef55f6744c45e3d7c85a3f74ada39b67ac741dd ]
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 070356513963be6196142acff56acc8359069fa1 ]
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise
some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or
DID_RESET just because sense data is missing.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c8ed783c2faa1e3f741844ffac41340338ea0f4 ]
This is mostly needed because an AztecMonster II target has been observed
disconnecting REQUEST SENSE commands and then failing to reselect properly.
Suggested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dad8261e643849ea134c7cd5c8e794e31d93b9eb ]
The return value is taken to mean "retry" or "don't retry". Change it to bool
to improve readability. Fix related comments. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1aeeeed7f03c576f096eede7b0384f99a98f588c ]
When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.
[mkp: adjusted Hannes' SoB address]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 32c850bf587f993b2620b91e5af8a64a7813f504 ]
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eebcc19646489b68399ce7b35d9c38eb9f4ec40f ]
Error paths in ufshcd_init() ufshcd_hba_exit() killed clk_scaling workqueue
when the workqueue is actually created quite late in ufshcd_init(). So, we
end up getting NULL pointer dereference in such error paths. Fix this by
moving clk_scaling initialization and kill codes to two separate methods, and
call them at required places.
Fixes: 401f1e4490ee ("scsi: ufs: don't suspend clock scaling during clock
gating")
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72349b62a571effd6faadd0600b8e657dd87afbf ]
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 76cb25b058034d37244be6aca97a2ad52a5fbcad ]
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 288315e95264b6355e26609e9dec5dc4563d4ab0 ]
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2879265f514b1f4154288243c91438ddbedb3ed4 ]
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aad59d5d34738d6fd8c359df8048a84cd443e504 ]
During attachment, the driver writes the EQ doorbell to disable potential
interrupts from an EQ. The current EQ doorbell format used for clearing the
interrupt is incorrect and uses an if_type=2 format, making the operation act
on the wrong EQ.
Correct the code to use the proper if_type=6 EQ doorbell format.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01a8aed6a009625282b6265880f6b20cbd7a9c70 ]
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3a03ee1102a44ccbd2c5de80a6e862ba23e9b55 ]
Current code relies on switch to provide a unique combination of WWPN +
NPORTID to tract an FC port. This patch tries to detect a case where switch
data base can get corrupted where multiple WWPNs can have the same Nport ID.
The 1st Nport ID on the list will be kept while the duplicate Nport ID will be
discarded.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 527b8ae3948bb59c13ebaa7d657ced56ea25ab05 ]
When FW rejects a command due to "entry_status" error (malform IOCB), the srb
resource needs to be returned back for cleanup. The filter to catch this is
in the wrong location.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d74c87a20adcc77b19753c315ad9c320b2288be ]
Clear port speed value on chip reset.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f99c5d294b3653e6ae563eaac5db5b4138afe31c ]
During adapter shutdown process check for register disconnect before
proceeding to call PCI functions.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8bccfe0d21b5adbba6ec4fe1776160b80d09f78a ]
Abort IOCB request can take up to 40s or 2 ABTS timeout. We will wait for
ABTS response for 20s. On a timeout, second ABTS can go out with another 20s
timeout. On 2nd ABTS timeout FW will automatically do Logout.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1073daa470d906f1853ed4b828f16e2350a5875c ]
Move ATIO queue processing out of hardware_lock to prevent deadlock.
Fixes: 3bb67df5b5f8 ("qla2xxx: Check for online flag instead of active reset when transmitting responses")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa9e6d7b9643fc50a88c7b7aa1e34be8dc032749 ]
When driver receive PLOGI/PRLI from FW, the WWPN value will be provided. If
it is not, then driver will terminate it. The WWPN allows driver to locate
the session or create a new session.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93eca6135183f7a71e36acd47655a085ed11bcdc ]
For target mode, any chip reset triggered before target mode is enabled will
be held off until user is ready to enable. This prevents the chip from
starting or running before it is intended.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d9bf0a9a268f7ca0b811d6e6a1fc783afa5c746 ]
When switch responds with error for Get Port Speed Command (GPSC), driver
should not proceed with telling FW about the speed of the remote port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 49cecca7dd49e2950ed6d973acfa84e7c8c7a480 ]
On Abort of initiator scsi command, the abort needs to follow the same qpair
as the the scsi command to prevent out of order processing.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9393c8de628cf0968d81a17cc11841e42191e041 upstream.
In scsi_mq_setup_tags(), cmd_size is calculated based on zero size for the
scatter-gather list in case the low level driver uses SG_NONE in its host
template.
cmd_size is passed on to the block layer for calculation of the request
size, and we've seen NULL pointer dereference errors from the block layer
in drivers where SG_NONE is used and a mq IO scheduler is active,
apparently as a consequence of this (see commit 68ab2d76e4be ("scsi:
cxlflash: Set sg_tablesize to 1 instead of SG_NONE"), and a recent patch by
Finn Thain converting the three m68k NFR5380 drivers to avoid setting
SG_NONE).
Try to avoid these errors by accounting for at least one sg list entry when
calculating cmd_size, regardless of whether the low level driver set a zero
sg_tablesize.
Tested on 030 m68k with the atari_scsi driver - setting sg_tablesize to
SG_NONE no longer results in a crash when loading this driver.
CC: Finn Thain <fthain@telegraphics.com.au>
Link: https://lore.kernel.org/r/1572922150-4358-1-git-send-email-schmitzmic@gmail.com
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d3566abb1a1e7772116e4d50fb6a58d19c9802e5 ]
In shutdown/reboot paths, the timer is not stopped:
qla2x00_shutdown
pci_device_shutdown
device_shutdown
kernel_restart_prepare
kernel_restart
sys_reboot
This causes lockups (on powerpc) when firmware config space access calls
are interrupted by smp_send_stop later in reboot.
Fixes: e30d1756480dc ("[SCSI] qla2xxx: Addition of shutdown callback handler.")
Link: https://lore.kernel.org/r/20191024063804.14538-1-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
James Smart
Shivasharan S
Suganath Prabu
Gustavo A. R. Silva
Finn Thain
Christoph Hellwig
Nathan Chancellor
Xiang Chen
Luo Jiaxing
Colin Ian King
Hannes Reinecke
Jason Yan
Vivek Gautam
Deepak Ukey
George Kennedy
Quinn Tran
Sawan Chandak
Michael Schmitz
Nicholas Piggin