| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 1b8d0300a3e9f216ae4901bab886db7299899ec6 ]
|- iscsi_if_destroy_conn |-dev_attr_show
|-iscsi_conn_teardown
|-spin_lock_bh |-iscsi_sw_tcp_conn_get_param
|-kfree(conn->persistent_address) |-iscsi_conn_get_param
|-kfree(conn->local_ipaddr)
==>|-read persistent_address
==>|-read local_ipaddr
|-spin_unlock_bh
When iscsi_conn_teardown() and iscsi_conn_get_param() happen in parallel, a
UAF may be triggered.
Link: https://lore.kernel.org/r/046ec8a0-ce95-d3fc-3235-666a7c65b224@huawei.com
Reported-by: Lu Tixiong <lutianxiong@huawei.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Lixiaokeng <lixiaokeng@huawei.com>
Signed-off-by: Linfeilong <linfeilong@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 142c779d05d1fef75134c3cb63f52ccbc96d9e1f upstream.
The PVSCSI implementation in the VMware hypervisor under specific
configuration ("SCSI Bus Sharing" set to "Physical") returns zero dataLen
in the completion descriptor for READ CAPACITY(16). As a result, the kernel
can not detect proper disk geometry. This can be recognized by the kernel
message:
[ 0.776588] sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
The PVSCSI implementation in QEMU does not set dataLen at all, keeping it
zeroed. This leads to a boot hang as was reported by Shmulik Ladkani.
It is likely that the controller returns the garbage at the end of the
buffer. Residual length should be set by the driver in that case. The SCSI
layer will erase corresponding data. See commit bdb2b8cab439 ("[SCSI] erase
invalid data returned by device") for details.
Commit e662502b3a78 ("scsi: vmw_pvscsi: Set correct residual data length")
introduced the issue by setting residual length unconditionally, causing
the SCSI layer to erase the useful payload beyond dataLen when this value
is returned as 0.
As a result, considering existing issues in implementations of PVSCSI
controllers, we do not want to call scsi_set_resid() when dataLen ==
0. Calling scsi_set_resid() has no effect if dataLen equals buffer length.
Link: https://lore.kernel.org/lkml/20210824120028.30d9c071@blondie/
Link: https://lore.kernel.org/r/20211220190514.55935-1-amakhalov@vmware.com
Fixes: e662502b3a78 ("scsi: vmw_pvscsi: Set correct residual data length")
Cc: Matt Wang <wwentao@vmware.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Vishal Bhakta <vbhakta@vmware.com>
Cc: VMware PV-Drivers <pv-drivers@vmware.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9020be114a47bf7ff33e179b3bb0016b91a098e6 ]
The "mybuf" string comes from the user, so we need to ensure that it is NUL
terminated.
Link: https://lore.kernel.org/r/20211214070527.GA27934@kili
Fixes: bd2cdd5e400f ("scsi: lpfc: NVME Initiator: Add debugfs support")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e0a2c28da11e2c2b963fc01d50acbf03045ac732 upstream.
In resp_mode_select() sanity check the block descriptor len to avoid UAF.
BUG: KASAN: use-after-free in resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
Read of size 1 at addr ffff888026670f50 by task scsicmd/15032
CPU: 1 PID: 15032 Comm: scsicmd Not tainted 5.15.0-01d0625 #15
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
Call Trace:
<TASK>
dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:107
print_address_description.constprop.9+0x28/0x160 mm/kasan/report.c:257
kasan_report.cold.14+0x7d/0x117 mm/kasan/report.c:443
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report_generic.c:306
resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
schedule_resp+0x4af/0x1a10 drivers/scsi/scsi_debug.c:5483
scsi_debug_queuecommand+0x8c9/0x1e70 drivers/scsi/scsi_debug.c:7537
scsi_queue_rq+0x16b4/0x2d10 drivers/scsi/scsi_lib.c:1521
blk_mq_dispatch_rq_list+0xb9b/0x2700 block/blk-mq.c:1640
__blk_mq_sched_dispatch_requests+0x28f/0x590 block/blk-mq-sched.c:325
blk_mq_sched_dispatch_requests+0x105/0x190 block/blk-mq-sched.c:358
__blk_mq_run_hw_queue+0xe5/0x150 block/blk-mq.c:1762
__blk_mq_delay_run_hw_queue+0x4f8/0x5c0 block/blk-mq.c:1839
blk_mq_run_hw_queue+0x18d/0x350 block/blk-mq.c:1891
blk_mq_sched_insert_request+0x3db/0x4e0 block/blk-mq-sched.c:474
blk_execute_rq_nowait+0x16b/0x1c0 block/blk-exec.c:63
sg_common_write.isra.18+0xeb3/0x2000 drivers/scsi/sg.c:837
sg_new_write.isra.19+0x570/0x8c0 drivers/scsi/sg.c:775
sg_ioctl_common+0x14d6/0x2710 drivers/scsi/sg.c:941
sg_ioctl+0xa2/0x180 drivers/scsi/sg.c:1166
__x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:52
do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:50
entry_SYSCALL_64_after_hwframe+0x44/0xae arch/x86/entry/entry_64.S:113
Link: https://lore.kernel.org/r/1637262208-28850-1-git-send-email-george.kennedy@oracle.com
Reported-by: syzkaller <syzkaller@googlegroups.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0c2f8b6709a9a4af175497ca65f93804f57b248 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ee4ba13e09c9d9c1cb6abb59da8295d9952328b ]
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4996c6eac4c81b8872043e9391563f67f13e406 ]
Pointers should be printed with %p or %px rather than cast to 'unsigned
long' and printed with %lx.
Change %lx to %p to print the hashed pointer.
Link: https://lore.kernel.org/r/20210929122538.1158235-1-qtxuning1999@sjtu.edu.cn
Signed-off-by: Guo Zhi <qtxuning1999@sjtu.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99154581b05c8fb22607afb7c3d66c1bace6aa5d ]
When parsing the txq list in lpfc_drain_txq(), the driver attempts to pass
the requests to the adapter. If such an attempt fails, a local "fail_msg"
string is set and a log message output. The job is then added to a
completions list for cancellation.
Processing of any further jobs from the txq list continues, but since
"fail_msg" remains set, jobs are added to the completions list regardless
of whether a wqe was passed to the adapter. If successfully added to
txcmplq, jobs are added to both lists resulting in list corruption.
Fix by clearing the fail_msg string after adding a job to the completions
list. This stops the subsequent jobs from being added to the completions
list unless they had an appropriate failure.
Link: https://lore.kernel.org/r/20210910233159.115896-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b7a9fd934a68ebfc1019811b7bdc1742072ad7b ]
When user uses issue_lip to do link bounce, driver sends additional target
reset to remote device before resetting the link. The target reset would
affect other paths with active I/Os. This patch will remove the unnecessary
target reset.
Link: https://lore.kernel.org/r/20211026115412.27691-4-njavali@marvell.com
Fixes: 5854771e314e ("[SCSI] qla2xxx: Add ISPFX00 specific bus reset routine")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f4875d509a0a78ad294a1a538d534b5ba94e685a ]
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili
Fixes: 5036f0a0ecd3 ("[SCSI] csiostor: Fix sparse warnings.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbd9a3347c757383f3d2b50cf7cfd03eb479c481 ]
dc395x_init_one()->adapter_init() might fail. In this case, the acb is
already cleaned up by adapter_init(), no need to do that in
adapter_uninit(acb) again.
[ 1.252251] dc395x: adapter init failed
[ 1.254900] RIP: 0010:adapter_uninit+0x94/0x170 [dc395x]
[ 1.260307] Call Trace:
[ 1.260442] dc395x_init_one.cold+0x72a/0x9bb [dc395x]
Link: https://lore.kernel.org/r/20210907040702.1846409-1-ztong0001@gmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a8f71014b4d56c4fb287607e844c0a9f68f46d9 ]
The sgl is freed in the target stack in target_release_cmd_kref() before
calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that
causes a panic if sgl is not yet DMA unmapped:
NIP dma_direct_unmap_sg+0xdc/0x180
LR dma_direct_unmap_sg+0xc8/0x180
Call Trace:
ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable)
dma_unmap_sg_attrs+0x54/0xf0
qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx]
qlt_free_cmd+0x124/0x1d0 [qla2xxx]
tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx]
target_put_sess_cmd+0x198/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]
The sgl may be left unmapped in error cases of response sending. For
instance, qlt_rdy_to_xfer() maps sgl and exits when session is being
deleted keeping the sgl mapped.
This patch removes use-after-free of the sgl and ensures that the sgl is
unmapped for any command that was not sent to firmware.
Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f2b85040acec9a928b4eb1b57a989324e8e38d3f upstream.
SCSI host release is triggered when SCSI device is freed. We have to make
sure that the low-level device driver module won't be unloaded before SCSI
host instance is released because shost->hostt is required in the release
handler.
Make sure to put LLD module refcnt after SCSI device is released.
Fixes a kernel panic of 'BUG: unable to handle page fault for address'
reported by Changhui and Yi.
Link: https://lore.kernel.org/r/20211008050118.1440686-1-ming.lei@redhat.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Changhui Zhong <czhong@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 50b6cb3516365cb69753b006be2b61c966b70588 upstream.
After commit ea2f0f77538c ("scsi: core: Cap scsi_host cmd_per_lun at
can_queue"), a 416-CPU VM running on Hyper-V hangs during boot because the
hv_storvsc driver sets scsi_driver.can_queue to an integer value that
exceeds SHRT_MAX, and hence scsi_add_host_with_dma() sets
shost->cmd_per_lun to a negative "short" value.
Use min_t(int, ...) to work around the issue.
Link: https://lore.kernel.org/r/20211008043546.6006-1-decui@microsoft.com
Fixes: ea2f0f77538c ("scsi: core: Cap scsi_host cmd_per_lun at can_queue")
Cc: stable@vger.kernel.org
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cced4c0ec7c06f5230a2958907a409c849762293 ]
There are a couple of spelling mistakes in pr_info and pr_err messages.
Fix them.
Link: https://lore.kernel.org/r/20210924230330.143785-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd689ed5aa905daf4ba4c99319a52aad6ea0a796 ]
Fix the following coccicheck warning:
./drivers/scsi/ses.c:137:10-16: WARNING: Unsigned expression compared
with zero: result > 0.
Link: https://lore.kernel.org/r/1632477113-90378-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fbdac19e642899455b4e64c63aafe2325df7aafa ]
Setting SCSI logging level with error=3, we saw some errors from enclosues:
[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13
Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).
Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Reviewed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 265dfe8ebbabae7959060bd1c3f75c2473b697ed ]
After a device is initialized via device_initialize() it should be freed
via put_device(). sd_probe() currently gets this wrong, fix it up.
Link: https://lore.kernel.org/r/20210906090112.531442-1-ming.lei@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79a7482249a7353bc86aff8127954d5febf02472 ]
Both cxgb4 and csiostor drivers run on their own independent Physical
Function. But when cxgb4 and csiostor are both being loaded in parallel via
modprobe, there is a race when firmware upgrade is attempted by both the
drivers.
When the cxgb4 driver initiates the firmware upgrade, it halts the firmware
and the chip until upgrade is complete. When the csiostor driver is coming
up in parallel, the firmware mailbox communication fails with timeouts and
the csiostor driver probe fails.
Add a module soft dependency on cxgb4 driver to ensure loading csiostor
triggers cxgb4 to load first when available to avoid the firmware upgrade
race.
Link: https://lore.kernel.org/r/1632759248-15382-1-git-send-email-rahul.lakkireddy@chelsio.com
Fixes: a3667aaed569 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e28550829258f7dab97383acaa477bd724c0ff4 ]
ISCSI_NET_PARAM_IFACE_ENABLE belongs to enum iscsi_net_param instead of
iscsi_iface_param so move it to ISCSI_NET_PARAM. Otherwise, when we call
into the driver, we might not match and return that we don't want attr
visible in sysfs. Found in code review.
Link: https://lore.kernel.org/r/20210901085336.2264295-1-libaokun1@huawei.com
Fixes: e746f3451ec7 ("scsi: iscsi: Fix iface sysfs attr detection")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c8fadf019964d0eb1da410ba8b629494d3339db9 upstream.
The first invocation of function find_first_zero_bit will return 0 and
queue_id gets set to 0.
An index of queue_pair_map also gets set to 0.
qpair_id = find_first_zero_bit(ha->qpair_qid_map, ha->max_qpairs);
set_bit(qpair_id, ha->qpair_qid_map);
ha->queue_pair_map[qpair_id] = qpair;
In the alloc_queue callback driver checks the map, if queue is already
allocated:
ha->queue_pair_map[qidx]
This works fine as long as max_qpairs is greater than nvme_max_hw_queues(8)
since the size of the queue_pair_map is equal to max_qpair. In case nr_cpus
is less than 8, max_qpairs is less than 8. This creates wrong value
returned as qpair.
[ 1572.353669] qla2xxx [0000:24:00.3]-2121:6: Returning existing qpair of 4e00000000000000 for idx=2
[ 1572.354458] general protection fault: 0000 [#1] SMP PTI
[ 1572.354461] CPU: 1 PID: 44 Comm: kworker/1:1H Kdump: loaded Tainted: G IOE --------- - - 4.18.0-304.el8.x86_64 #1
[ 1572.354462] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 03/01/2013
[ 1572.354467] Workqueue: kblockd blk_mq_run_work_fn
[ 1572.354485] RIP: 0010:qla_nvme_post_cmd+0x92/0x760 [qla2xxx]
[ 1572.354486] Code: 84 24 5c 01 00 00 00 00 b8 0a 74 1e 66 83 79 48 00 0f 85 a8 03 00 00 48 8b 44 24 08 48 89 ee 4c 89 e7 8b 50 24 e8 5e 8e 00 00 <f0> 41 ff 47 04 0f ae f0 41 f6 47 24 04 74 19 f0 41 ff 4f 04 b8 f0
[ 1572.354487] RSP: 0018:ffff9c81c645fc90 EFLAGS: 00010246
[ 1572.354489] RAX: 0000000000000001 RBX: ffff8ea3e5070138 RCX: 0000000000000001
[ 1572.354490] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff8ea4c866b800
[ 1572.354491] RBP: ffff8ea4c866b800 R08: 0000000000005010 R09: ffff8ea4c866b800
[ 1572.354492] R10: 0000000000000001 R11: 000000069d1ca3ff R12: ffff8ea4bc460000
[ 1572.354493] R13: ffff8ea3e50702b0 R14: ffff8ea4c4c16a58 R15: 4e00000000000000
[ 1572.354494] FS: 0000000000000000(0000) GS:ffff8ea4dfd00000(0000) knlGS:0000000000000000
[ 1572.354495] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1572.354496] CR2: 000055884504fa58 CR3: 00000005a1410001 CR4: 00000000000606e0
[ 1572.354497] Call Trace:
[ 1572.354503] ? check_preempt_curr+0x62/0x90
[ 1572.354506] ? dma_direct_map_sg+0x72/0x1f0
[ 1572.354509] ? nvme_fc_start_fcp_op.part.32+0x175/0x460 [nvme_fc]
[ 1572.354511] ? blk_mq_dispatch_rq_list+0x11c/0x730
[ 1572.354515] ? __switch_to_asm+0x35/0x70
[ 1572.354516] ? __switch_to_asm+0x41/0x70
[ 1572.354518] ? __switch_to_asm+0x35/0x70
[ 1572.354519] ? __switch_to_asm+0x41/0x70
[ 1572.354521] ? __switch_to_asm+0x35/0x70
[ 1572.354522] ? __switch_to_asm+0x41/0x70
[ 1572.354523] ? __switch_to_asm+0x35/0x70
[ 1572.354525] ? entry_SYSCALL_64_after_hwframe+0xb9/0xca
[ 1572.354527] ? __switch_to_asm+0x41/0x70
[ 1572.354529] ? __blk_mq_sched_dispatch_requests+0xc6/0x170
[ 1572.354531] ? blk_mq_sched_dispatch_requests+0x30/0x60
[ 1572.354532] ? __blk_mq_run_hw_queue+0x51/0xd0
[ 1572.354535] ? process_one_work+0x1a7/0x360
[ 1572.354537] ? create_worker+0x1a0/0x1a0
[ 1572.354538] ? worker_thread+0x30/0x390
[ 1572.354540] ? create_worker+0x1a0/0x1a0
[ 1572.354541] ? kthread+0x116/0x130
[ 1572.354543] ? kthread_flush_work_fn+0x10/0x10
[ 1572.354545] ? ret_from_fork+0x35/0x40
Fix is to use index 0 for admin and first IO queue.
Link: https://lore.kernel.org/r/20210810043720.1137-14-njavali@marvell.com
Fixes: e84067d74301 ("scsi: qla2xxx: Add FC-NVMe F/W initialization and transport registration")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44d01fc86d952f5a8b8b32bdb4841504d5833d95 upstream.
Update BusLogic driver's messaging system to use pr_cont() for continuation
lines, bringing messy output:
pci 0000:00:13.0: PCI->APIC IRQ transform: INT A -> IRQ 17
scsi: ***** BusLogic SCSI Driver Version 2.1.17 of 12 September 2013 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
scsi0: Firmware Version: 5.07B, I/O Address: 0x7000, IRQ Channel: 17/Level
scsi0: PCI Bus: 0, Device: 19, Address:
0xE0012000,
Host Adapter SCSI ID: 7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: Ultra, Wide Negotiation: Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
scsi0: Tagged Queue Depth:
Automatic
, Untagged Queue Depth: 3
scsi0: SCSI Bus Termination: Both Enabled
, SCAM: Disabled
scsi0: *** BusLogic BT-958 Initialized Successfully ***
scsi host0: BusLogic BT-958
back to order:
pci 0000:00:13.0: PCI->APIC IRQ transform: INT A -> IRQ 17
scsi: ***** BusLogic SCSI Driver Version 2.1.17 of 12 September 2013 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
scsi0: Firmware Version: 5.07B, I/O Address: 0x7000, IRQ Channel: 17/Level
scsi0: PCI Bus: 0, Device: 19, Address: 0xE0012000, Host Adapter SCSI ID: 7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: Ultra, Wide Negotiation: Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0: SCSI Bus Termination: Both Enabled, SCAM: Disabled
scsi0: *** BusLogic BT-958 Initialized Successfully ***
scsi host0: BusLogic BT-958
Also diagnostic output such as with the BusLogic=TraceConfiguration
parameter is affected and becomes vertical and therefore hard to read.
This has now been corrected, e.g.:
pci 0000:00:13.0: PCI->APIC IRQ transform: INT A -> IRQ 17
blogic_cmd(86) Status = 30: 4 ==> 4: FF 05 93 00
blogic_cmd(95) Status = 28: (Modify I/O Address)
blogic_cmd(91) Status = 30: 1 ==> 1: 01
blogic_cmd(04) Status = 30: 4 ==> 4: 41 41 35 30
blogic_cmd(8D) Status = 30: 14 ==> 14: 45 DC 00 20 00 00 00 00 00 40 30 37 42 1D
scsi: ***** BusLogic SCSI Driver Version 2.1.17 of 12 September 2013 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
blogic_cmd(04) Status = 30: 4 ==> 4: 41 41 35 30
blogic_cmd(0B) Status = 30: 3 ==> 3: 00 08 07
blogic_cmd(0D) Status = 30: 34 ==> 34: 03 01 07 04 00 00 00 00 00 00 00 00 00 00 00 00 FF 42 44 46 FF 00 00 00 00 00 00 00 00 00 FF 00 FF 00
blogic_cmd(8D) Status = 30: 14 ==> 14: 45 DC 00 20 00 00 00 00 00 40 30 37 42 1D
blogic_cmd(84) Status = 30: 1 ==> 1: 37
blogic_cmd(8B) Status = 30: 5 ==> 5: 39 35 38 20 20
blogic_cmd(85) Status = 30: 1 ==> 1: 42
blogic_cmd(86) Status = 30: 4 ==> 4: FF 05 93 00
blogic_cmd(91) Status = 30: 64 ==> 64: 41 46 3E 20 39 35 38 20 20 00 C4 00 04 01 07 2F 07 04 35 FF FF FF FF FF FF FF FF FF FF 01 00 FE FF 08 FF FF 00 00 00 00 00 00 00 01 00 01 00 00 FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 FC
scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
etc.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2104201940430.44318@angie.orcam.me.uk
Fixes: 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing continuation lines")
Cc: stable@vger.kernel.org # v4.9+
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4dbe57d46d54a847875fa33e7d05877bb341585e ]
This function had some left over code that returned 1 on error instead
negative error codes. Convert everything to use negative error codes. The
caller treats all non-zero returns the same so this does not affect run
time.
A couple places set "rc" instead of "status" so those error paths ended up
returning success by mistake. Get rid of the "rc" variable and use
"status" everywhere.
Remove the bogus "status = 0" initialization, as a future proofing measure
so the compiler will warn about uninitialized error codes.
Link: https://lore.kernel.org/r/20210810084753.GD23810@kili
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70edd2e6f652f67d854981fd67f9ad0f1deaea92 ]
Avoid printing a 'target allocation failed' error if the driver
target_alloc() callback function returns -ENXIO. This return value
indicates that the corresponding H:C:T:L entry is empty.
Removing this error reduces the scan time if the user issues SCAN_WILD_CARD
scan operation through sysfs parameter on a host with a lot of empty
H:C:T:L entries.
Avoiding the printk on -ENXIO matches the behavior of the other callback
functions during scanning.
Link: https://lore.kernel.org/r/20210726115402.1936-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc546c0c9abb3bb2fb46866b3d1e6ade9695a5f6 ]
The following BUG_ON() was observed during RDAC scan:
[595952.944297] kernel BUG at drivers/scsi/device_handler/scsi_dh_rdac.c:427!
[595952.951143] Internal error: Oops - BUG: 0 [#1] SMP
......
[595953.251065] Call trace:
[595953.259054] check_ownership+0xb0/0x118
[595953.269794] rdac_bus_attach+0x1f0/0x4b0
[595953.273787] scsi_dh_handler_attach+0x3c/0xe8
[595953.278211] scsi_dh_add_device+0xc4/0xe8
[595953.282291] scsi_sysfs_add_sdev+0x8c/0x2a8
[595953.286544] scsi_probe_and_add_lun+0x9fc/0xd00
[595953.291142] __scsi_scan_target+0x598/0x630
[595953.295395] scsi_scan_target+0x120/0x130
[595953.299481] fc_user_scan+0x1a0/0x1c0 [scsi_transport_fc]
[595953.304944] store_scan+0xb0/0x108
[595953.308420] dev_attr_store+0x44/0x60
[595953.312160] sysfs_kf_write+0x58/0x80
[595953.315893] kernfs_fop_write+0xe8/0x1f0
[595953.319888] __vfs_write+0x60/0x190
[595953.323448] vfs_write+0xac/0x1c0
[595953.326836] ksys_write+0x74/0xf0
[595953.330221] __arm64_sys_write+0x24/0x30
Code is in check_ownership:
list_for_each_entry_rcu(tmp, &h->ctlr->dh_list, node) {
/* h->sdev should always be valid */
BUG_ON(!tmp->sdev);
tmp->sdev->access_state = access_state;
}
rdac_bus_attach
initialize_controller
list_add_rcu(&h->node, &h->ctlr->dh_list);
h->sdev = sdev;
rdac_bus_detach
list_del_rcu(&h->node);
h->sdev = NULL;
Fix the race between rdac_bus_attach() and rdac_bus_detach() where h->sdev
is NULL when processing the RDAC attach.
Link: https://lore.kernel.org/r/20210113063103.2698953-1-yebin10@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77541f78eadfe9fdb018a7b8b69f0f2af2cf4b82 ]
The list_for_each_entry() iterator, "adapter" in this code, can never be
NULL. If we exit the loop without finding the correct adapter then
"adapter" points invalid memory that is an offset from the list head. This
will eventually lead to memory corruption and presumably a kernel crash.
Link: https://lore.kernel.org/r/20210708074642.23599-1-harshvardhan.jha@oracle.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c04243a56a7977185b00400e59ca7e108004faf ]
Media event code 3 is defined in the MMC-6 spec as follows:
"MediaRemoval: The media has been removed from the specified slot, and
the Drive is unable to access the media without user intervention. This
applies to media changers only."
This indicated that treating the condition as an EJECT_REQUEST was
appropriate. However, doing so had the unfortunate side-effect of causing
the drive tray to be physically ejected on resume. Instead treat the event
as a MEDIA_CHANGE request.
Fixes: 7dd753ca59d6 ("scsi: sr: Return appropriate error code when disk is ejected")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213759
Link: https://lore.kernel.org/r/20210726114913.6760-1-limanyi@uniontech.com
Signed-off-by: Li Manyi <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e746f3451ec7f91dcc9fd67a631239c715850a34 ]
A ISCSI_IFACE_PARAM can have the same value as a ISCSI_NET_PARAM so when
iscsi_iface_attr_is_visible tries to figure out the type by just checking
the value, we can collide and return the wrong type. When we call into the
driver we might not match and return that we don't want attr visible in
sysfs. The patch fixes this by setting the type when we figure out what the
param is.
Link: https://lore.kernel.org/r/20210701002559.89533-1-michael.christie@oracle.com
Fixes: 3e0f65b34cc9 ("[SCSI] iscsi_transport: Additional parameters for network settings")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b27c4577557045f1ab3cdfeabfc7f3cd24aca1fe ]
Fix array index out of bound exception in fc_rport_prli_resp().
Link: https://lore.kernel.org/r/20210615165939.24327-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 332a9dd1d86f1e7203fc7f0fd7e82f0b304200fe ]
The shifting of the u8 integer returned fom ahc_inb(ahc, port+3) by 24 bits
to the left will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the event that the top bit of the u8 is set then all then all
the upper 32 bits of the u64 end up as also being set because of the
sign-extension. Fix this by casting the u8 values to a u64 before the 24
bit left shift.
[ This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit f58eb66c0b0a ("Update aic7xxx driver to 6.2.10...") ]
Link: https://lore.kernel.org/r/20210621151727.20667-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unintended sign extension")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 030e4138d11fced3b831c2761e4cecf347bae99c ]
If an error occurs after a pci_enable_pcie_error_reporting() call, it must
be undone by a corresponding pci_disable_pcie_error_reporting() call, as
already done in the remove function.
Link: https://lore.kernel.org/r/77adb02cfea7f1364e5603ecf3930d8597ae356e.1623482155.git.christophe.jaillet@wanadoo.fr
Fixes: 3567f36a09d1 ("[SCSI] be2iscsi: Fix AER handling in driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5777b7f0f03ce49372203b6521631f62f2810c8f ]
If qedi_process_cmd_cleanup_resp finds the cmd it frees the work and sets
list_tmf_work to NULL, so qedi_tmf_work should check if list_tmf_work is
non-NULL when it wants to force cleanup.
Link: https://lore.kernel.org/r/20210525181821.7617-20-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdd4aad7ff92ae39c2e93c415bb6761cb8b584da ]
The iscsi offload drivers are setting the shost->max_id to the max number
of sessions they support. The problem is that max_id is not the max number
of targets but the highest identifier the targets can have. To use it to
limit the number of targets we need to set it to max sessions - 1, or we
can end up with a session we might not have preallocated resources for.
Link: https://lore.kernel.org/r/20210525181821.7617-15-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1d19e8c92cfb0ded180ef3376c20e130414e067 ]
There are a couple places where we could free the iscsi_cls_conn while it's
still in use. This adds some helpers to get/put a refcount on the struct
and converts an exiting user. Subsequent commits will then use the helpers
to fix 2 bugs in the eh code.
Link: https://lore.kernel.org/r/20210525181821.7617-11-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea2f0f77538c50739b9fb4de4700cee5535e1f77 ]
The sysfs handling function sdev_store_queue_depth() enforces that the sdev
queue depth cannot exceed shost can_queue. The initial sdev queue depth
comes from shost cmd_per_lun. However, the LLDD may manually set
cmd_per_lun to be larger than can_queue, which leads to an initial sdev
queue depth greater than can_queue.
Such an issue was reported in [0], which caused a hang. That has since been
fixed in commit fc09acb7de31 ("scsi: scsi_debug: Fix cmd_per_lun, set to
max_queue").
Stop this possibly happening for other drivers by capping shost cmd_per_lun
at shost can_queue.
[0] https://lore.kernel.org/linux-scsi/YHaez6iN2HHYxYOh@T590/
Link: https://lore.kernel.org/r/1621434662-173079-1-git-send-email-john.garry@huawei.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5aa615d195f1e142c662cb2253f057c9baec7531 ]
The driver is encountering a crash in lpfc_free_iocb_list() while
performing initial attachment.
Code review found this to be an errant failure path that was taken, jumping
to a tag that then referenced structures that were uninitialized.
Fix the failure path.
Link: https://lore.kernel.org/r/20210514195559.119853-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e30d55137edef47434c40d7570276a0846fe922c ]
An 'unexpected timeout' message may be seen in a point-2-point topology.
The message occurs when a PLOGI is received before the driver is notified
of FLOGI completion. The FLOGI completion failure causes discovery to be
triggered for a second time. The discovery timer is restarted but no new
discovery activity is initiated, thus the timeout message eventually
appears.
In point-2-point, when discovery has progressed before the FLOGI completion
is processed, it is not a failure. Add code to FLOGI completion to detect
that discovery has progressed and exit the FLOGI handling (noop'ing it).
Link: https://lore.kernel.org/r/20210514195559.119853-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 93aa71ad7379900e61c8adff6a710a4c18c7c99b upstream.
Commit 66a834d09293 ("scsi: core: Fix error handling of scsi_host_alloc()")
changed the allocation logic to call put_device() to perform host cleanup
with the assumption that IDA removal and stopping the kthread would
properly be performed in scsi_host_dev_release(). However, in the unlikely
case that the error handler thread fails to spawn, shost->ehandler is set
to ERR_PTR(-ENOMEM).
The error handler cleanup code in scsi_host_dev_release() will call
kthread_stop() if shost->ehandler != NULL which will always be the case
whether the kthread was successfully spawned or not. In the case that it
failed to spawn this has the nasty side effect of trying to dereference an
invalid pointer when kthread_stop() is called. The following splat provides
an example of this behavior in the wild:
scsi host11: error handler thread failed to spawn, error = -4
Kernel attempted to read user page (10c) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x0000010c
Faulting instruction address: 0xc00000000818e9a8
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ibmvscsi(+) scsi_transport_srp dm_multipath dm_mirror dm_region
hash dm_log dm_mod fuse overlay squashfs loop
CPU: 12 PID: 274 Comm: systemd-udevd Not tainted 5.13.0-rc7 #1
NIP: c00000000818e9a8 LR: c0000000089846e8 CTR: 0000000000007ee8
REGS: c000000037d12ea0 TRAP: 0300 Not tainted (5.13.0-rc7)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 28228228
XER: 20040001
CFAR: c0000000089846e4 DAR: 000000000000010c DSISR: 40000000 IRQMASK: 0
GPR00: c0000000089846e8 c000000037d13140 c000000009cc1100 fffffffffffffffc
GPR04: 0000000000000001 0000000000000000 0000000000000000 c000000037dc0000
GPR08: 0000000000000000 c000000037dc0000 0000000000000001 00000000fffff7ff
GPR12: 0000000000008000 c00000000a049000 c000000037d13d00 000000011134d5a0
GPR16: 0000000000001740 c0080000190d0000 c0080000190d1740 c000000009129288
GPR20: c000000037d13bc0 0000000000000001 c000000037d13bc0 c0080000190b7898
GPR24: c0080000190b7708 0000000000000000 c000000033bb2c48 0000000000000000
GPR28: c000000046b28280 0000000000000000 000000000000010c fffffffffffffffc
NIP [c00000000818e9a8] kthread_stop+0x38/0x230
LR [c0000000089846e8] scsi_host_dev_release+0x98/0x160
Call Trace:
[c000000033bb2c48] 0xc000000033bb2c48 (unreliable)
[c0000000089846e8] scsi_host_dev_release+0x98/0x160
[c00000000891e960] device_release+0x60/0x100
[c0000000087e55c4] kobject_release+0x84/0x210
[c00000000891ec78] put_device+0x28/0x40
[c000000008984ea4] scsi_host_alloc+0x314/0x430
[c0080000190b38bc] ibmvscsi_probe+0x54/0xad0 [ibmvscsi]
[c000000008110104] vio_bus_probe+0xa4/0x4b0
[c00000000892a860] really_probe+0x140/0x680
[c00000000892aefc] driver_probe_device+0x15c/0x200
[c00000000892b63c] device_driver_attach+0xcc/0xe0
[c00000000892b740] __driver_attach+0xf0/0x200
[c000000008926f28] bus_for_each_dev+0xa8/0x130
[c000000008929ce4] driver_attach+0x34/0x50
[c000000008928fc0] bus_add_driver+0x1b0/0x300
[c00000000892c798] driver_register+0x98/0x1a0
[c00000000810eb60] __vio_register_driver+0x80/0xe0
[c0080000190b4a30] ibmvscsi_module_init+0x9c/0xdc [ibmvscsi]
[c0000000080121d0] do_one_initcall+0x60/0x2d0
[c000000008261abc] do_init_module+0x7c/0x320
[c000000008265700] load_module+0x2350/0x25b0
[c000000008265cb4] __do_sys_finit_module+0xd4/0x160
[c000000008031110] system_call_exception+0x150/0x2d0
[c00000000800d35c] system_call_common+0xec/0x278
Fix this be nulling shost->ehandler when the kthread fails to spawn.
Link: https://lore.kernel.org/r/20210701195659.3185475-1-tyreld@linux.ibm.com
Fixes: 66a834d09293 ("scsi: core: Fix error handling of scsi_host_alloc()")
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 104739aca4488909175e9e31d5cd7d75b82a2046 upstream.
If the device is power-cycled, it takes time for the initiator to transmit
the periodic NOTIFY (ENABLE SPINUP) SAS primitive, and for the device to
respond to the primitive to become ACTIVE. Retry the I/O request to allow
the device time to become ACTIVE.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210629155826.48441-1-quat.le@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Quat Le <quat.le@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d6c2ce435ffe23ef7f395ae76ec747414589db46 ]
When an expander does not contain any 'phys', an appropriate error code -1
should be returned, as done elsewhere in this function. However, we
currently do not explicitly assign this error code to 'rc'. As a result, 0
was incorrectly returned.
Link: https://lore.kernel.org/r/20210514081300.6650-1-thunder.leizhen@huawei.com
Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d431153e751caa93f3b7e6f6313446974e92253 ]
The BusLogic driver has build errors on ia64 due to a name collision (in
the #included FlashPoint.c file). Rename the struct field in struct
sccb_mgr_info from si_flags to si_mflags (manager flags) to mend the build.
This is the first problem. There are 50+ others after this one:
In file included from ../include/uapi/linux/signal.h:6,
from ../include/linux/signal_types.h:10,
from ../include/linux/sched.h:29,
from ../include/linux/hardirq.h:9,
from ../include/linux/interrupt.h:11,
from ../drivers/scsi/BusLogic.c:27:
../arch/ia64/include/uapi/asm/siginfo.h:15:27: error: expected ':', ',', ';', '}' or '__attribute__' before '.' token
15 | #define si_flags _sifields._sigfault._flags
| ^
../drivers/scsi/FlashPoint.c:43:6: note: in expansion of macro 'si_flags'
43 | u16 si_flags;
| ^~~~~~~~
In file included from ../drivers/scsi/BusLogic.c:51:
../drivers/scsi/FlashPoint.c: In function 'FlashPoint_ProbeHostAdapter':
../drivers/scsi/FlashPoint.c:1076:11: error: 'struct sccb_mgr_info' has no member named '_sifields'
1076 | pCardInfo->si_flags = 0x0000;
| ^~
../drivers/scsi/FlashPoint.c:1079:12: error: 'struct sccb_mgr_info' has no member named '_sifields'
Link: https://lore.kernel.org/r/20210529234857.6870-1-rdunlap@infradead.org
Fixes: 391e2f25601e ("[SCSI] BusLogic: Port driver to 64-bit.")
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7dd753ca59d6c8cc09aa1ed24f7657524803c7f3 ]
Handle a reported media event code of 3. This indicates that the media has
been removed from the drive and user intervention is required to proceed.
Return DISK_EVENT_EJECT_REQUEST in that case.
Link: https://lore.kernel.org/r/20210611094402.23884-1-limanyi@uniontech.com
Signed-off-by: ManYi Li <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1e0d4e6225996f05271de1ebcb1a7c9381af0b27 upstream.
get_device(shost->shost_gendev.parent) is called after host state has
switched to SHOST_RUNNING. scsi_host_dev_release() shouldn't release the
parent device if host state is still SHOST_CREATED.
Link: https://lore.kernel.org/r/20210602133029.2864069-5-ming.lei@redhat.com
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11714026c02d613c30a149c3f4c4a15047744529 upstream.
scsi_host_dev_release() only frees dev_name when host state is
SHOST_CREATED. After host state has changed to SHOST_RUNNING,
scsi_host_dev_release() no longer cleans up.
Fix this by doing a put_device(&shost->shost_dev) in the failure path when
host state is SHOST_RUNNING. Move get_device(&shost->shost_gendev) before
device_add(&shost->shost_dev) so that scsi_host_cls_release() can do a put
on this reference.
Link: https://lore.kernel.org/r/20210602133029.2864069-4-ming.lei@redhat.com
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hannes Reinecke <hare@suse.de>
Reported-by: John Garry <john.garry@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66a834d092930cf41d809c0e989b13cd6f9ca006 upstream.
After device is initialized via device_initialize(), or its name is set via
dev_set_name(), the device has to be freed via put_device(). Otherwise
device name will be leaked because it is allocated dynamically in
dev_set_name().
Fix the leak by replacing kfree() with put_device(). Since
scsi_host_dev_release() properly handles IDA and kthread removal, remove
special-casing these from the error handling as well.
Link: https://lore.kernel.org/r/20210602133029.2864069-2-ming.lei@redhat.com
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2ef7665dfd88830f15415ba007c7c9a46be7acd8 ]
Target de-configuration panics at high CPU load because TPGT and WWPN can
be removed on separate threads.
TPGT removal requests a reset HBA on a separate thread and waits for reset
complete (phase1). Due to high CPU load that HBA reset can be delayed for
some time.
WWPN removal does qlt_stop_phase2(). There it is believed that phase1 has
already completed and thus tgt.tgt_ops is subsequently cleared. However,
tgt.tgt_ops is needed to process incoming traffic and therefore this will
cause one of the following panics:
NIP qlt_reset+0x7c/0x220 [qla2xxx]
LR qlt_reset+0x68/0x220 [qla2xxx]
Call Trace:
0xc000003ffff63a78 (unreliable)
qlt_handle_imm_notify+0x800/0x10c0 [qla2xxx]
qlt_24xx_atio_pkt+0x208/0x590 [qla2xxx]
qlt_24xx_process_atio_queue+0x33c/0x7a0 [qla2xxx]
qla83xx_msix_atio_q+0x54/0x90 [qla2xxx]
or
NIP qlt_24xx_handle_abts+0xd0/0x2a0 [qla2xxx]
LR qlt_24xx_handle_abts+0xb4/0x2a0 [qla2xxx]
Call Trace:
qlt_24xx_handle_abts+0x90/0x2a0 [qla2xxx] (unreliable)
qlt_24xx_process_atio_queue+0x500/0x7a0 [qla2xxx]
qla83xx_msix_atio_q+0x54/0x90 [qla2xxx]
or
NIP qlt_create_sess+0x90/0x4e0 [qla2xxx]
LR qla24xx_do_nack_work+0xa8/0x180 [qla2xxx]
Call Trace:
0xc0000000348fba30 (unreliable)
qla24xx_do_nack_work+0xa8/0x180 [qla2xxx]
qla2x00_do_work+0x674/0xbf0 [qla2xxx]
qla2x00_iocb_work_fn
The patch fixes the issue by serializing qlt_stop_phase1() and
qlt_stop_phase2() functions to make WWPN removal wait for phase1
completion.
Link: https://lore.kernel.org/r/20210415203554.27890-1-d.bogdanov@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e662502b3a782d479e67736a5a1c169a703d853a ]
Some commands (such as INQUIRY) may return less data than the initiator
requested. To avoid conducting useless information, set the right residual
count to make upper layer aware of this.
Before (INQUIRY PAGE 0xB0 with 128B buffer):
$ sg_raw -r 128 /dev/sda 12 01 B0 00 80 00
SCSI Status: Good
Received 128 bytes of data:
00 00 b0 00 3c 01 00 00 00 00 00 00 00 00 00 00 00 ...<............
10 00 00 00 00 00 01 00 00 00 00 00 40 00 00 08 00 ...........@....
20 80 00 00 00 00 00 00 00 00 00 20 00 00 00 00 00 .......... .....
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
After:
$ sg_raw -r 128 /dev/sda 12 01 B0 00 80 00
SCSI Status: Good
Received 64 bytes of data:
00 00 b0 00 3c 01 00 00 00 00 00 00 00 00 00 00 00 ...<............
10 00 00 00 00 00 01 00 00 00 00 00 40 00 00 08 00 ...........@....
20 80 00 00 00 00 00 00 00 00 00 20 00 00 00 00 00 .......... .....
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[mkp: clarified description]
Link: https://lore.kernel.org/r/03C41093-B62E-43A2-913E-CFC92F1C70C3@vmware.com
Signed-off-by: Matt Wang <wwentao@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c7e7b8486cda21269d393245883c5e4737d5ee7 ]
If sas_notify_lldd_dev_found() fails then this code calls:
sas_unregister_dev(port, dev);
which removes "dev", our list iterator, from the list. This could lead to
an endless loop. We need to use list_for_each_entry_safe().
Link: https://lore.kernel.org/r/YKUeq6gwfGcvvhty@mwanda
Fixes: 303694eeee5e ("[SCSI] libsas: suspend / resume support")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56f396146af278135c0ff958c79b5ee1bd22453d ]
Commit 391e2f25601e ("[SCSI] BusLogic: Port driver to 64-bit")
introduced a serious issue for 64-bit systems. With this commit,
64-bit kernel will enumerate 8*15 non-existing disks. This is caused
by the broken CCB structure. The change from u32 data to void *data
increased CCB length on 64-bit system, which introduced an extra 4
byte offset of the CDB. This leads to incorrect response to INQUIRY
commands during enumeration.
Fix disk enumeration failure by reverting the portion of the commit
above which switched the data pointer from u32 to void.
Link: https://lore.kernel.org/r/C325637F-1166-4340-8F0F-3BCCD59D4D54@vmware.com
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Matt Wang <wwentao@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5cb289bf2d7c34ca1abd794ce116c4f19185a1d4 ]
Fix to return a negative error code from the error handling case instead of
0 as done elsewhere in this function.
Link: https://lore.kernel.org/r/20210514090952.6715-1-thunder.leizhen@huawei.com
Fixes: a9083016a531 ("[SCSI] qla2xxx: Add ISP82XX support.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Lixiaokeng
Alexey Makhalov
Dan Carpenter
George Kennedy
Mike Christie
Sreekanth Reddy
Guo Zhi
James Smart
Quinn Tran
Tong Zhang
Dmitry Bogdanov
Ming Lei
Dexuan Cui
Colin Ian King
Jiapeng Chong
Wen Xiong
Rahul Lakkireddy
Baokun Li
Saurav Kashyap
Maciej W. Rozycki
Ye Bin
Harshvardhan Jha
Li Manyi
Javed Hasan
Christophe JAILLET
John Garry
Tyrel Datwyler
Quat Le
Zhen Lei
Randy Dunlap
Matt Wang