| Age | Commit message (Collapse) | Author |
|---|
|
commit 2fe8a236436fe40d8d26a1af8d150fc80f04ee1a upstream.
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1cfef80d4c2b2c599189f36f36320b205d9447d9 ]
dev_close() and dev_open() are issued to change the interface state to DOWN
or UP (dev->flags IFF_UP). When the netdev is set DOWN it loses e.g its
Ipv6 addresses and routes. We don't want this in cases of device recovery
(triggered by hardware or software) or when the qeth device is set
offline.
Setting a qeth device offline or online and device recovery actions call
netif_device_detach() and/or netif_device_attach(). That will reset or
set the LOWER_UP indication i.e. change the dev->state Bit
__LINK_STATE_PRESENT. That is enough to e.g. cause bond failovers, and
still preserves the interface settings that are handled by the network
stack.
Don't call dev_open() nor dev_close() from the qeth device driver. Let the
network stack handle this.
Fixes: d4560150cb47 ("s390/qeth: call dev_close() during recovery")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80de809bd35e2a8999edf9f5aaa2d8de18921f11 ]
Change boolean parameter of function "qeth_l3_vipa_store" inside the
"qeth_l3_dev_vipa_del4_store" function from "true" to "false" because
"true" is used for adding a virtual ip address and "false" for deleting.
Fixes: 2390166a6b45 ("s390/qeth: clean up L3 sysfs code")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb16db8393658e0978c3f0d30ae069e878264fa3 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88d86d18d7cf7e9137c95f9d212bb9fff8a1b4be ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/netiucv.c:1854:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = netiucv_tx,
^~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of netiucv_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa5bf80c3c067b82b4362cd6e8e2194623bcaca6 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/ctcm_main.c:1064:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcm_tx,
^~~~~~~
drivers/s390/net/ctcm_main.c:1072:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcmpc_tx,
^~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of ctc{mp,}m_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 671bb35c8e746439f0ed70815968f9a4f20a8deb ]
smatch complains about
drivers/s390/net/lcs.c:1741 lcs_get_control() warn: variable dereferenced before check 'card->dev' (see line 1739)
Fixes: 27eb5ac8f015 ("[PATCH] s390: lcs driver bug fixes and improvements [1/2]")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c0b20587b9f25a2ad14db7f80ebe49bdf29920a ]
smatch complains about
drivers/s390/net/ctcm_mpc.c:1210 ctcmpc_unpack_skb() warn: possible memory leak of 'mpcginfo'
mpc_action_discontact() did not free mpcginfo. Consolidate the freeing in
ctcmpc_unpack_skb().
Fixes: 293d984f0e36 ("ctcm: infrastructure for replaced ctc driver")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c50c6867c85afee6f2b3bcbc50fc9d0083d1343 ]
Found by cppcheck and smatch.
smatch complains about
drivers/s390/net/ctcm_sysfs.c:43 ctcm_buffer_write() warn: variable dereferenced before check 'priv' (see line 42)
Fixes: 3c09e2647b5e ("ctcm: rename READ/WRITE defines to avoid redefinitions")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 248f064af222a1f97ee02c84a98013dfbccad386 ]
When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().
qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).
Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.
Fix it by checking the pointer for NULL before accessing it.
Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.
Fixes: eff73e16ee11 ("s390/qeth: tolerate pre-filled RX buffer")
Reported-by: Stefan Raspl <raspl@linux.ibm.com>
Root-caused-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e83d467a08e25b27c44c885f511624a71c84f7c ]
When a QAOB notifies us that a pending TX buffer has been delivered, the
actual TX completion processing by qeth_tx_complete_pending_bufs()
is done within the context of a TX NAPI instance. We shouldn't rely on
this instance being scheduled by some other TX event, but just do it
ourselves.
qeth_qdio_handle_aob() is called from qeth_poll(), ie. our main NAPI
instance. To avoid touching the TX queue's NAPI instance
before/after it is (un-)registered, reorder the code in qeth_open()
and qeth_stop() accordingly.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7eefda7f353ef86ad82a2dc8329e8a3538c08ab6 ]
The cited commit reworked the state machine for pending TX buffers.
In qeth_iqd_tx_complete() it turned PENDING into a transient state, and
uses NEED_QAOB for buffers that get parked while waiting for their QAOB
completion.
But it missed to adjust the check in qeth_tx_complete_buf(). So if
qeth_tx_complete_pending_bufs() is called during teardown to drain
the parked TX buffers, we no longer raise a notification for af_iucv.
Instead of updating the checked state, just move this code into
qeth_tx_complete_pending_bufs() itself. This also gets rid of the
special-case in the common TX completion path.
Fixes: 8908f36d20d8 ("s390/qeth: fix af_iucv notification race")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c20383ad1656b0f6354dd50e4acd894f9d94090d ]
The current design attaches a pending TX buffer to a custom
single-linked list, which is anchored at the buffer's slot on the
TX ring. The buffer is then checked for final completion whenever
this slot is processed during a subsequent TX NAPI poll cycle.
But if there's insufficient traffic on the ring, we might never make
enough progress to get back to this ring slot and discover the pending
buffer's final TX completion. In particular if this missing TX
completion blocks the application from sending further traffic.
So convert the custom single-linked list code to a per-queue list_head,
and scan this list on every TX NAPI cycle.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75cf3854dcdf7b5c583538cae12ffa054d237d93 ]
Reuse the QETH_QDIO_BUF_EMPTY state to indicate that a TX buffer has
been completed with a QAOB notification, and may be cleaned up by
qeth_cleanup_handled_pending().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db4ffdcef7c9a842e55228c9faef7abf8b72382f ]
For TX buffers that require an additional async notification via QAOB, the
TX completion code can now manage all the necessary processing if the
notification has already occurred (or is occurring concurrently).
In such cases we can avoid replacing the metadata that is associated
with the buffer's slot on the ring, and just keep using the current one.
As qeth_clear_output_buffer() will also handle any kmem cache-allocated
memory that was mapped into the TX buffer, qeth_qdio_handle_aob()
doesn't need to worry about it.
While at it, also remove the unneeded forward declaration for
qeth_init_qdio_out_buf().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e7a36d27f6b9f389e41d8189a8a08919c6835732 upstream.
When qeth_alloc_qdio_queues() fails to allocate one of the buffers that
back an Output Queue, the 'out_freeoutqbufs' path will free all
previously allocated buffers for this queue. But it misses to free the
half-finished queue struct itself.
Move the buffer allocation into qeth_alloc_output_queue(), and deal with
such errors internally.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f9c4845385c8f6631ebd5dddfb019ea7a285fba4 ]
ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().
Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.
Fixes: f13ade199391 ("s390/qeth: run non-offload L3 traffic over common xmit path")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b41b554c1ee75070a14c02a88496b1f231c7eacc ]
Due to insufficient locking, qeth_core_set_online() and
qeth_dev_layer2_store() can run in parallel, both attempting to load &
setup the discipline (and stepping on each other toes along the way).
A similar race can also occur between qeth_core_remove_device() and
qeth_dev_layer2_store().
Access to .discipline is meant to be protected by the discipline_mutex,
so add/expand the locking in qeth_core_remove_device() and
qeth_core_set_online().
Adjust the locking in qeth_l*_remove_device() accordingly, as it's now
handled by the callers in a consistent manner.
Based on an initial patch by Ursula Braun.
Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0b9902c1fcc59ba75268386c0420a554f8844168 ]
When qeth_dev_layer2_store() - holding the discipline_mutex - waits
inside qeth_l*_remove_device() for a qeth_do_reset() thread to complete,
we can hit a deadlock if qeth_do_reset() concurrently calls
qeth_set_online() and thus tries to aquire the discipline_mutex.
Move the discipline_mutex locking outside of qeth_set_online() and
qeth_set_offline(), and turn the discipline into a parameter so that
callers understand the dependency.
To fix the deadlock, we can now relax the locking:
As already established, qeth_l*_remove_device() waits for
qeth_do_reset() to complete. So qeth_do_reset() itself is under no risk
of having card->discipline ripped out while it's running, and thus
doesn't need to take the discipline_mutex.
Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When qeth_iqd_tx_complete() detects that a TX buffer requires additional
async completion via QAOB, it might fail to replace the queue entry's
metadata (and ends up triggering recovery).
Assume now that the device gets torn down, overruling the recovery.
If the QAOB notification then arrives before the tear down has
sufficiently progressed, the buffer state is changed to
QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob().
The tear down code calls qeth_drain_output_queue(), where
qeth_cleanup_handled_pending() will then attempt to replace such a
buffer _again_. If it succeeds this time, the buffer ends up dangling in
its replacement's ->next_pending list ... where it will never be freed,
since there's no further call to qeth_cleanup_handled_pending().
But the second attempt isn't actually needed, we can simply leave the
buffer on the queue and re-use it after a potential recovery has
completed. The qeth_clear_output_buffer() in qeth_drain_output_queue()
will ensure that it's in a clean state again.
Fixes: 72861ae792c2 ("qeth: recovery through asynchronous delivery")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The two expected notification sequences are
1. TX_NOTIFY_PENDING with a subsequent TX_NOTIFY_DELAYED_*, when
our TX completion code first observed the pending TX and the QAOB
then completes at a later time; or
2. TX_NOTIFY_OK, when qeth_qdio_handle_aob() picked up the QAOB
completion before our TX completion code even noticed that the TX
was pending.
But as qeth_iqd_tx_complete() and qeth_qdio_handle_aob() can run
concurrently, we may end up with a race that results in a sequence of
TX_NOTIFY_DELAYED_* followed by TX_NOTIFY_PENDING. Which would confuse
the af_iucv code in its tracking of pending transmits.
Rework the notification code, so that qeth_qdio_handle_aob() defers its
notification if the TX completion code is still active.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Calling into socket code is ugly already, at least check whether we are
dealing with the expected sk_family. Only looking at skb->protocol is
bound to cause troubles (consider eg. af_packet).
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove workaround that supported early hardware implementations
of PNSO OC3. Rely on the 'enarf' feature bit instead.
Fixes: fa115adff2c1 ("s390/qeth: Detect PNSO OC3 capability")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
[jwi: use logical instead of bit-wise AND]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The system EID that is defined by the ISM driver is not correct. Using
an incorrect system EID allows to communicate with remote Linux systems
that use the same incorrect system EID, but when it comes to
interoperability with other operating systems then the system EIDs do
never match which prevents SMC-Dv2 communication.
Using the correct system EID fixes this problem.
Fixes: 201091ebb2a1 ("net/smc: introduce System Enterprise ID (SEID)")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/s390/net/ctcm_fsms.h: fsm_action_nop - only declaration left
after commit 04885948b101 ("ctc: removal of the old ctc driver")
drivers/s390/net/ctcm_mpc.h: ctcmpc_open - only declaration left after
commit 293d984f0e36 ("ctcm: infrastructure for replaced ctc driver")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Add/delete some blanks, white spaces and braces.
- Fix misindentations.
- Adjust a deprecated header include, and htons() conversion.
- Remove extra 'return' statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace our custom version of netdev_name().
Once we started to allocate the netdev at probe time with
commit d3d1b205e89f ("s390/qeth: allocate netdevice early"), this
stopped working as intended anyway.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The discipline struct is a fixed group of function pointers.
So declare the L2 and L3 disciplines as constant.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For OSA devices that are _not_ configured in prio-queue mode, give users
the option of selecting the number of active TX queues.
This requires setting up the HW queues with a reasonable default QoS
value in the QIB's PQUE parm area.
As with the other device types, we bring up the device with a minimal
number of TX queues for compatibility reasons.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a proper struct, and only program the QIB extensions for devices
where they are supported.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When re-initializing a device, we can hit a situation where
qeth_osa_set_output_queues() detects that it supports more or less
HW TX queues than before. Right now we adjust dev->real_num_tx_queues
from right there, but
1. it's getting more & more complicated to cover all cases, and
2. we can't re-enable the actually expected number of TX queues later
because we lost the needed information.
So keep track of the wanted TX queues (on initial setup, and whenever
its changed via .set_channels), and later use that information when
re-enabling the netdevice.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With SMCD version 2 the CHIDs of ISM devices are needed for the
CLC handshake.
This patch provides the new callback to retrieve the CHID of an
ISM device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMCD version 2 defines a System Enterprise ID (short SEID).
This patch contains the SEID creation and adds the callback to
retrieve the created SEID.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shuffle some code around (primarily all the discipline-related stuff) to
get rid of all the unnecessary forward declarations.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clarify which discipline-specific steps are needed to roll back after
error in qeth_l?_set_online(), and which are common to roll back
from qeth_hardsetup_card().
Some steps (cancelling the RX modeset, draining the TX queues) are only
necessary if the netdev was potentially UP before, so move them to the
common qeth_set_offline().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move duplicated code from the disciplines into the core path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Originators of cmd IO typically hold the rtnl or conf_mutex to protect
against a concurrent teardown.
Since qeth_set_offline() already holds the conf_mutex, the main reason
why we still care about cancelling pending cmds is so that they release
the rtnl when we need it ourselves.
So move this step a little earlier into the teardown sequence.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The programming of ucast IPs via qeth_l3_modify_ip() is driven
independently from any of our typical locking mechanisms (eg. detaching
the netdevice, or holding the conf_mutex).
So when we inspect the card state to check whether the required cmd IO
should be deferred, there is no protection against concurrent state
changes.
But by slightly re-ordering the teardown sequence, we can rely on the
ip_lock to sufficiently serialize things:
1. when running concurrently to qeth_l3_set_online(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_recover_ip() will observe the state as CARD_STATE_SOFTSETUP
and not defer the IO.
2. when running concurrently to qeth_l3_set_offline(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_clear_ip_htable() will observe the state as CARD_STATE_DOWN
and defer the IO.
These guarantees in mind, we can now drop the conf_mutex from the
qeth_l3_modify_rxip_vipa() wrapper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the remaining occurences in sysfs code to kstrtouint().
While at it move some input parsing out of locked sections, replace an
open-coded clamp() and remove some unnecessary run-time checks for
ipatoe->mask_bits that are already enforced when creating the object.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indicate the max number of to-be-parsed characters, and avoid copying
the address sub-string.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
card->ipato is currently protected by the conf_mutex. But most users
also hold the ip_lock - in particular qeth_l3_add_ip().
So slightly expand the sections under ip_lock in a few places (to
effectively cover a few error & no-op cases), and then drop the
conf_mutex where it's no longer needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mcast IP objects are allocated within qeth_l3_add_mcast_rtnl(),
with .ref_counter already set to 1 via qeth_l3_init_ipaddr().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to control whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB, where they will show up as 'extern_learn offload'. So we map
qeth_l2_dev2br_an_set() to the learning_sync bridge link attribute.
Turning off learning_sync will flush all extern_learn entries from the
bridge fdb and all pending events from the card's work queue.
When the hardware interface goes offline with learning_sync on
(e.g. for HW recovery), all extern_learn entries will be flushed from the
bridge fdb and all pending events from the card's work queue. When the
interface goes online again, it will send new notifications for all then
valid MACs. learning_sync attribute can not be modified while interface is
offline. See
'commit e6e771b3d897 ("s390/qeth: detach netdevice while card is offline")'
An alternative implementation would be to always offload the 'learning'
attribute of a software bridge to the hardware interface attached to it
and thus implicitly enable fdb notification. This was not chosen for 2
reasons:
1) In our case the software bridge is NOT a representation of a hardware
switch. It is just connected to a smart NIC that is able to inform
about the addresses attached to it. It is not necessarily using source
MAC learning for this and other bridgeports can be attached to other
NICs with different properties.
2) We want a means to enable this notification explicitly. There may be
cases where a bridgeport is set to 'learning', but we do not want to
enable the notification.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to indicate whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB.
learning_sync attribute can not be read while interface is offline (down).
See
'commit e6e771b3d897 ("s390/qeth: detach netdevice while card is offline")'
We return EOPNOTSUPP and not EONODEV in this case, because EONOTSUPP is the
only rc that is tolerated by 'bridge -d link show'.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case hardware sends more device-to-bridge-address-change notfications
than the qeth-l2 driver can handle, the hardware will send an overflow
event and then stop sending any events. It expects software to flush its
FDB and start over again. Re-enabling address-change-notification will
report all current addresses.
In order to re-enable address-change-notification this patch defines
the functions qeth_l2_dev2br_an_set() and qeth_l2_dev2br_an_set_cb
to enable or disable dev-to-bridge-address-notification.
A following patch will use the learning_sync bridgeport flag to trigger
enabling or disabling of address-change-notification, so we define
priv->brport_features to store the current setting. BRIDGE_INFO and
ADDR_INFO functionality are mutually exclusive, whereas ADDR_INFO and
qeth_l2_vnicc* can be used together.
Alternative implementations to handle buffer overflow:
Just re-enabling notification and adding all newly reported addresses
would cover any lost 'add' events, but not the lost 'delete' events.
Then these invalid addresses would stay in the bridge FDB as long as the
device exists.
Setting the net device down and up, would be an alternative, but is a bit
drastic. If the net device has many secondary addresses this will create
many delete/add events at its peers which could de-stabilize the
network segment.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A qeth-l2 HiperSockets card can show switch-ish behaviour in the sense,
that it can report all MACs that are reachable via this interface. Just
like a switch device, it can notify the software bridge about changes
to its fdb. This patch exploits this device-to-bridge-notification and
extracts the relevant information from the hardware events to generate
notifications to an attached software bridge.
There are 2 sources for this information:
1) The reply message of Perform-Network-Subchannel-Operations (PNSO)
(operation code ADDR_INFO) reports all addresses that are currently
reachable (implemented in a later patch).
2) As long as device-to-bridge-notification is enabled, hardware will
generate address change notification events, whenever the content of
the hardware fdb changes (this patch).
The bridge_hostnotify feature (PNSO operation code BRIDGE_INFO) uses
the same address change notification events. We need to distinguish
between qeth_pnso_mode QETH_PNSO_BRIDGEPORT and QETH_PNSO_ADDR_INFO
and call a different handler. In both cases deadlocks must be
prevented, if the workqueue is drained under lock and QETH_PNSO_NONE,
when notification is disabled.
bridge_hostnotify generates udev events, there is no intend to do the same
for dev2br. Instead this patch will generate SWITCHDEV_FDB_ADD_TO_BRIDGE
and SWITCHDEV_FDB_DEL_TO_BRIDGE notifications, that will cause the
software bridge to add (or delete) entries to its fdb as 'extern_learn
offload'.
Documentation/networking/switchdev.txt proposes to add
"depends NET_SWITCHDEV" to driver's Kconfig. This is not done here,
so even in absence of the NET_SWITCHDEV module, the QETH_L2 module will
still be built, but then the switchdev notifiers will have no effect.
No VLAN filtering is done on the entries and VLAN information is not
passed on to the bridge fdb entries. This could be added later.
For now VLAN interfaces can be defined on the upper bridge interface.
Multicast entries are not passed on to the bridge fdb.
This could be added later. For now mcast flooding can be used in the
bridge.
The card reports all MACs that are in its FDB, but we must not pass on
MACs that are registered for this interface.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch detects whether device-to-bridge-notification, provided
by the Perform Network Subchannel Operation (PNSO) operation code
ADDR_INFO (OC3), is supported by this card. A following patch will
map this to the learning_sync bridgeport flag, so we store it in
priv->brport_hw_features in bridgeport flag format.
Only IQD cards provide PNSO.
There is a feature bit to indicate whether the machine provides OC3,
unfortunately it is not set on old machines.
So PNSO is called to find out. As this will disable notification
and is exclusive with bridgeport_notification, this must be done
during card initialisation before previous settings are restored.
PNSO functionality requires some configuration values that are added to
the qeth_card.info structure. Some helper functions are defined to fill
them out when the card is brought online and some other places are
adapted, that can also benefit from these fields.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for operation code 3 (OC3) of the
Perform-Network-Subchannel-Operations (PNSO) function
of the Channel-Subsystem-Call (CHSC) instruction.
PNSO provides 2 operation codes:
OC0 - BRIDGE_INFO
OC3 - ADDR_INFO (new)
Extend the function calls to *pnso* to pass the OC and
add new response code 0108.
Support for OC3 is indicated by a flag in the css_general_characteristics.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arch/s390/net/pnet.c uses ccwgroup function dev_is_ccwgroup()
in pnetid_by_dev_port().
For s390 the net/smc code makes use of function pnetid_by_dev_port().
Make sure ccwgroup is built into the kernel, if smc is to be built
into the kernel.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Alexandra Winter
Thorsten Winkler
Nathan Chancellor
Julian Wiedmann
Karsten Graul
Vasily Gorbik
Ursula Braun
David S. Miller
Guvenc Gulce