| Age | Commit message (Collapse) | Author |
|---|
|
|
|
[ Upstream commit 0401f24cd238ae200a23a13925f98de3d2c883b8 ]
When a driver calls pwmchip_add() it has to be prepared to immediately
get its callbacks called. So move allocation of driver data and hardware
initialization before the call to pwmchip_add().
This fixes a potential NULL pointer exception and a race condition on
register writes.
Fixes: 841e6f90bb78 ("pwm: NXP LPC18xx PWM/SCT driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit d44084c93427bb0a9261432db1a8ca76a42d805e ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d768cd7fd42bb0be16f36aec48548fca5260759 ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c68eb29c8e9067c08175dd0414f6984f236f719d ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
registered
commit 3d2813fb17e5fd0d73c1d1442ca0192bde4af10e upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb93 ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value")
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
[ Upstream commit 65e2e6c1c20104ed19060a38f4edbf14e9f9a9a5 ]
As the last call to sprd_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 8aae4b02e8a6 ("pwm: sprd: Add Spreadtrum PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit 1bc6ea31cb41d50302a3c9b401964cf0a88d41f9 ]
The .remove() callback disables clocks that were not enabled in
.probe(). So just probing and then unbinding the driver results in a clk
enable imbalance.
So just drop the call to disable the clocks. (Which BTW was also in the
wrong order because the call makes the PWM unfunctional and so should
have come only after pwmchip_remove()).
Fixes: 9f4c8f9607c3 ("pwm: imx: Add ipg clock operation")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86f7fa71cd830d18d7ebcaf719dffd5ddfe1acdd ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fde25294dfd8e36e4e30b693c27a86232864002a ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b601a18f12383001e7a8da238de7ca1559ebc450 ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
[ Upstream commit d5d8d675865ccddfe4da26c85f22c55cec663bf2 ]
If rockchip_pwm_probe() fails to register a PWM device it calls
clk_unprepare() for the device's PWM clock, without having first disabled
the clock and before jumping to an error handler that also unprepares
it. This is likely to produce warnings from the kernel about the clock
being unprepared when it is still enabled, and then being unprepared when
it has already been unprepared.
Prevent these warnings by removing this unnecessary call to
clk_unprepare().
Fixes: 48cf973cae33 ("pwm: rockchip: Avoid glitches on already running PWMs")
Signed-off-by: Simon South <simon@simonsouth.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit 1f0f1e80fdd3aa9631f6c22cda4f8550cfcfcc3e ]
When there are other PWM controllers enabled along with pwm-lp3943,
pwm-lp3942 is failing to probe with -EEXIST error. This is because
other PWM controllers are probed first and assigned PWM base 0 and
pwm-lp3943 is requesting for 0 again.
In order to avoid this, assign the chip base with -1, so that it is
dynamically allocated.
Fixes: af66b3c0934e ("pwm: Add LP3943 PWM driver")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Uwe Kleine-König <u.kleine-könig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 269effd03f6142df4c74814cfdd5f0b041b30bf9 ]
zx_pwm_probe() called clk_prepare_enable() before; this must be undone
in the error path.
Fixes: 4836193c435c ("pwm: Add ZTE ZX PWM device driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b3d3f016b1f46bd28f5ad3f0485c66922fbf8c93 from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
commit 6b28fb6f3ca30bd98815041b4eb795743706402d upstream.
Implement .apply callback and drop the legacy callbacks(enable, disable,
config, set_polarity). In .apply() check for the current hardware status
before changing the PWM configuration.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit 56232f53d280b7277b97486a8bfc9d254577f6d7 from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
commit e793eef8062f4a5b24433d0e0aac2ddf9cf71da8 upstream.
Only the Timer control register(TCLR) cannot be updated when the timer
is running. Registers like Counter register (TCRR), loader register
(TLDR) and match register (TMAR) can be updated while the counter is
running. Since TCLR is not updated in pwm_omap_dmtimer_config(), do not
stop the timer for period/duty_cycle update.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit 0a5372cedb062b952ff7274bc75257916c91a15e from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
commit 867beb60d131f7a5cde88ba375338285fdc6ddb8 upstream.
To configure DM timer in PWM mode the following needs to be set in
OMAP_TIMER_CTRL_REG using set_pwm callback:
- Set toggle mode on PORTIMERPWM output pin
- Set trigger on overflow and match on PORTIMERPWM output pin.
- Set auto reload
This is a one time configuration and needs to be set before the start of
the DM timer. But the current driver tries to set the same configuration
for every period/duty cycle update, which is not needed. So move the PWM
setup before enabling timer and do not update it in
pwm_omap_dmtimer_config().
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit cae3fbcfbb8042780fb1b9ed7668b5af2f68b33a from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
commit 348fb6f7fb4cc7ebc35d1cde6e5c2ada64b683c6 upstream.
Update the description with a brief about how PWM is generated using
OMAP DM timer and add limitations for the PWM generations. Also add a
link to the reference manual.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit 5893afee4c7446ee2564383d119b4675e8cf1269 from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
commit 54091b5f195b45a9a7d394008c06d2b9646ab126 upstream.
pwm_omap_dmtimer.h is used only:
- to typedef struct omap_dm_timer to pwm_omap_dmtimer
- for macro PWM_OMAP_DMTIMER_TRIGGER_OVERFLOW_AND_COMPARE
Rest of the file is pretty mush unsed. So reuse omap_dm_timer
and OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE in pwm-omap-dmtimer.c
and delete the header file.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit 09f5199bb6424f01fec8d28ceccc903deaab48d5 from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
commit 02e6d546e3bdc1a8a764343cd1ba354da07e8623 upstream.
dm timer ops set_load() api allows to configure the load value and to
set the auto reload feature. But auto reload feature is independent of
load value and should be part of configuring pwm. This way pwm can be
disabled by disabling auto reload feature using set_pwm() so that the
current pwm cycle will be completed. Else pwm disabling causes the
cycle to be stopped abruptly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200305082715.15861-7-lokeshvutla@ti.com
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit 793f366fee1e24dbb67c5d1135a897e434565b43 from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
This adds a new pwm driver that supports the PRUSS IEP-based PWM. It
uses remoteporc framework to communicate with PRUSS.
A PRUSS has two pwmchips because of two IEP modules, and each pwmchip
has upto 12 PWMs. This PRUSS PWM requires a firmware running on PRU
which uses IEP compare events to generate PWM output.
This driver implements two platform device drivers. One handles the
PRUSS PWM module calling remoteproc to initialize the PRU. The other one
is the pwmchip device driver to handle the two pwmchips.
PWM polarity inverse is not supported by the PRU firmware.
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
commit 9452ba6cac80772be906d02f547d7376cf102d9c from
git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
Populate the sysfs device into pwmchip so that the pwm chip
drivers can access its sysfs entries.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
|
|
[ Upstream commit b39c0615d0667b3a6f2f5c4bf99ffadf3b518bb1 ]
dev_get_drvdata() is called in img_pwm_runtime_resume() before the
driver data is set.
When pm_runtime_enabled() returns false in img_pwm_probe() it calls
img_pwm_runtime_resume() which results in a null pointer access.
This patch fixes the problem by setting the driver data earlier in the
img_pwm_probe() function.
This crash was seen when booting the Imagination Technologies Creator
Ci40 (Marduk) with kernel 5.4 in OpenWrt.
Fixes: e690ae526216 ("pwm: img: Add runtime PM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef9f60daab309558c8bb3e086a9a11ee40bd6061 ]
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 181f4d2f44463fe09fe4df02e03095cb87151c29 ]
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ced5ff0be8e94871ba846dfbddf69d21363f3d7 ]
Handle clk_get_rate() returning 0 to avoid possible division by zero.
Fixes: daa5abc41c80 ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
When commit 9017dc4fbd59 ("pwm: jz4740: Enhance precision in calculation
of duty cycle") from v5.8-rc1 was backported to v5.4.x its dependency on
commit ce1f9cece057 ("pwm: jz4740: Use clocks from TCU driver") was not
noticed which made the pwm-jz4740 driver fail to build.
As ce1f9cece057 depends on still more rework, just backport a small part
of this commit to make the driver build again. (There is no dependency
on the functionality introduced in ce1f9cece057, just the rate variable
is needed.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9017dc4fbd59c09463019ce494cfe36d654495a8 upstream.
Calculating the hardware value for the duty from the hardware value of
the period resulted in a precision loss versus calculating it from the
clock rate directly.
(Also remove a cast that doesn't really need to be here)
Fixes: f6b8a5700057 ("pwm: Add Ingenic JZ4740 support")
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
[ukl: backport to v5.4.y and adapt commit log accordingly]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca162ce98110b98e7d97b7157328d34dcfdd40a9 ]
Even in failed case of pm_runtime_get_sync(), the usage_count is
incremented. In order to keep the usage_count with correct value call
appropriate pm_runtime_put().
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c25b07e5ec119cab609e41407a1fb3fa61442f5 ]
The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().
Fixes: e5a06dc5ac1f ("pwm: Add BCM2835 PWM driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d5a3c7a4536e1329a758e14340efd0e65252bd3d ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.
Fixes: 99b82abb0a35b073 ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1451a3eed24b5fd6a604683f0b6995e0e7e16c79 ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should be disabled after the removal of the PWM
chip.
Fixes: ed6c1476bf7f16d5 ("pwm: Add support for R-Car PWM Timer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9cc5f232a4b6a0ef6e9b57876d61b88f61bdd7c2 upstream.
This driver allows pwms to be requested as gpios via gpiolib. Obviously,
it should not be allowed to request a GPIO when its corresponding PWM is
already requested (and vice versa). So it requires some exclusion code.
Given that the PWMm and GPIO cores are not synchronized with respect to
each other, this exclusion code will also require proper
synchronization.
Such a mechanism was in place, but was inadvertently removed by Uwe's
clean-up in commit e926b12c611c ("pwm: Clear chip_data in pwm_put()").
Upon revisiting the synchronization mechanism, we found that
theoretically, it could allow two threads to successfully request
conflicting PWMs/GPIOs.
Replace with a bitmap which tracks PWMs in-use, plus a mutex. As long as
PWM and GPIO's respective request/free functions modify the in-use
bitmap while holding the mutex, proper synchronization will be
guaranteed.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: e926b12c611c ("pwm: Clear chip_data in pwm_put()")
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.org/lkml/2019/5/31/963
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[cg: Tested on an i.MX6Q board with two NXP PCA9685 chips]
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com> # cg's rebase
Link: https://lore.kernel.org/lkml/20200330160238.GD2817345@ulmo/
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7cb3a1dd53f63c64fb2b567d0be130b92a44d91 upstream.
This was found by coccicheck:
drivers/pwm/pwm-omap-dmtimer.c:304:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 255, but without a corresponding
object release within this function.
Reported-by: Markus Elfring <elfring@users.sourceforge.net>
Fixes: 6604c6556db9 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9871abffc81048e20f02e15d6aa4558a44ad53ea ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pwm/pwm-pca9685.c: In function ‘pca9685_pwm_gpio_free’:
drivers/pwm/pwm-pca9685.c:162:21: warning: variable ‘pwm’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed. In that case, hold and release
the lock 'pca->lock' can be removed since nothing will be done between
them.
Fixes: e926b12c611c ("pwm: Clear chip_data in pwm_put()")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 43efdc8f0e6d7088ec61bd55a73bf853f002d043 ]
In the old code (e.g.) mutex_destroy() was called before
pwmchip_remove(). Between these two calls it is possible that a PWM
callback is used which tries to grab the mutex.
Fixes: 6604c6556db9 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4cf7aa57eb83b108d2d9c6c37c143388fee2a4d ]
Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.
This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.
Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.
Fixes: 6604c6556db9 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 50cc7e3e4f26e3bf5ed74a8d061195c4d2161b8b ]
Since 5.4-rc1, pwm_apply_state calls ->get_state after ->apply
if available, and this revealed an issue with integer precision
when calculating duty_cycle and period for the currently set
state in ->get_state callback.
This issue manifested in broken backlight on several Allwinner
based devices.
Previously this worked, because ->apply updated the passed state
directly.
Fixes: deb9c462f4e53 ("pwm: sun4i: Don't update the state for the caller of pwm_apply_state")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes: daa5abc41c80 ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
It turns out that commit 01ccf903edd6 ("pwm: Let pwm_get_state() return
the last implemented state") causes backlight failures on a number of
boards. The reason is that some of the drivers do not write the full
state through to the hardware registers, which means that ->get_state()
subsequently does not return the correct state. Consumers which rely on
pwm_get_state() returning the current state will therefore get confused
and subsequently try to program a bad state.
Before this change can be made, existing drivers need to be more
carefully audited and fixed to behave as the framework expects. Until
then, keep the original behaviour of returning the software state that
was applied rather than reading the state back from hardware.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
|
|
This adds pwm support for MT7629, and separate mt7629 compatible string
from mt7622
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add SPDX identifiers to pwm-mediatek.c. Update MODULE_LICENSE to
correctly reflect the GNU General Public License v2.0.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use pwm_mediatek as common prefix to match the filename. No functional
change intended.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Instead of using fixed size of arrays, allocate the memory for them
based on the number of PWMs specified for each SoC generation.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
Bruce Ashfield
Uwe Kleine-König
Zou Wei
Simon South
Lokesh Vutla
Bin Liu
Hauke Mehrtens
Hans de Goede
Rayagonda Kokatanur
Paul Cercueil
Navid Emamdoost
Florian Fainelli
Geert Uytterhoeven
Sven Van Asbroeck
yu kuai
Ondrej Jirman
Thierry Reding
Linus Torvalds
Sam Shih