| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 95339f40a8b652b5b1773def31e63fc53c26378a ]
The logic used for power_supply_is_system_supplied() counts all power
supplies and assumes that the system is running from AC if there is
either a non-battery power-supply reporting to be online or if no
power-supplies exist at all.
The second rule is for desktop systems, that don't have any
battery/charger devices. These systems will incorrectly report to be
powered from battery once a device scope power-supply is registered
(e.g. a HID device), since these power-supplies increase the counter.
Apart from HID devices, recent dGPUs provide UCSI power supplies on a
desktop systems. The dGPU by default doesn't have anything plugged in so
it's 'offline'. This makes power_supply_is_system_supplied() return 0
with a count of 1 meaning all drivers that use this get a wrong judgement.
To fix this case adjust the logic to also examine the scope of the power
supply. If the power supply is deemed a device power supply, then don't
count it.
Cc: Evan Quan <Evan.Quan@amd.com>
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 155c45a25679f571c2ae57d10db843a9dfc63430 ]
Reduce the amount of output this dev_dbg() statement emits into logs,
otherwise if system software polls the sysfs entry for data and keeps
getting -ENODATA, it could end up filling the logs up.
This does in fact make systemd journald choke, since during boot the
sysfs power supply entries are polled and if journald starts at the
same time, the journal is just being repeatedly filled up, and the
system stops on trying to start journald without booting any further.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59dddea9879713423c7b2ade43c423bb71e0d216 ]
Use mod_delayed_work() instead of separate cancel_delayed_work_sync() +
schedule_delayed_work() calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d5c129d6c8993fe96e9ae712141eedcb9ca68c2 ]
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a5299ce4e96f3e8930e9c051b28d8093ada87b08 ]
ab8500_btemp_external_power_changed() dereferences di->btemp_psy,
which gets sets in ab8500_btemp_probe() like this:
di->btemp_psy = devm_power_supply_register(dev, &ab8500_btemp_desc,
&psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77c2a3097d7029441e8a91aa0de1b4e5464593da ]
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695ac ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
power_supply_set_input_current_limit_from_supplier()
[ Upstream commit 2220af8ca61ae67de4ec3deec1c6395a2f65b9fd ]
Some (USB) charger ICs have variants with USB D+ and D- pins to do their
own builtin charger-type detection, like e.g. the bq24190 and bq25890 and
also variants which lack this functionality, e.g. the bq24192 and bq25892.
In case the charger-type; and thus the input-current-limit detection is
done outside the charger IC then we need some way to communicate this to
the charger IC. In the past extcon was used for this, but if the external
detection does e.g. full USB PD negotiation then the extcon cable-types do
not convey enough information.
For these setups it was decided to model the external charging "brick"
and the parameters negotiated with it as a power_supply class-device
itself; and power_supply_set_input_current_limit_from_supplier() was
introduced to allow drivers to get the input-current-limit this way.
But in some cases psy drivers may want to know other properties, e.g. the
bq25892 can do "quick-charge" negotiation by pulsing its current draw,
but this should only be done if the usb_type psy-property of its supplier
is set to DCP (and device-properties indicate the board allows higher
voltages).
Instead of adding extra helper functions for each property which
a psy-driver wants to query from its supplier, refactor
power_supply_set_input_current_limit_from_supplier() into a
more generic power_supply_get_property_from_supplier() function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: 77c2a3097d70 ("power: supply: bq24190: Call power_supply_changed() after updating input current")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
stabilize
[ Upstream commit 59a99cd462fbdf71f4e845e09f37783035088b4f ]
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b2f2a3c9800208b0db2c2e34b05323757117faa2 upstream.
CHARGE_INHIBITED bit position of the ChargerStatus register is actually
0 not 1. This patch corrects it.
Fixes: feb583e37f8a8 ("power: supply: add sbs-charger driver")
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c00bc80462afc7963f449d7f21d896d2f629cacc upstream.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 444ff00734f3878cd54ddd1ed5e2e6dbea9326d5 upstream.
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c34c0aef185dcd10881847b9ebf20046aa77cb4 upstream.
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4484643991e0f6b89060092563f0dbab9450cbb upstream.
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 44263f50065969f2344808388bd589740f026167 ]
power-supply properties are reported in µV, µA and µW.
The IIO API provides mV, mA, mW, so the values need to
be multiplied by 1000.
Fixes: e60fea794e6e ("power: battery: Generic battery driver using IIO")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 14c76b2e75bca4d96e2b85a0c12aa43e84fe3f74 ]
This doesn't need to be printed every second as an error:
...
<3>[17438.628385] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17439.634176] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17440.640298] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
...
Reduce priority from ERROR to DEBUG.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
to race condition
[ Upstream commit 06615d11cc78162dfd5116efb71f29eb29502d37 ]
In da9150_charger_probe, &charger->otg_work is bound with
da9150_charger_otg_work. da9150_charger_otg_ncb may be
called to start the work.
If we remove the module which will call da9150_charger_remove
to make cleanup, there may be a unfinished work. The possible
sequence is as follows:
Fix it by canceling the work before cleanup in the da9150_charger_remove
CPU0 CPUc1
|da9150_charger_otg_work
da9150_charger_remove |
power_supply_unregister |
device_unregister |
power_supply_dev_release|
kfree(psy) |
|
| power_supply_changed(charger->usb);
| //use
Fixes: c1a281e34dae ("power: Add support for DA9150 Charger")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 104bb8a663451404a26331263ce5b96c34504049 ]
when kmalloc() fail to allocate memory in kasprintf(), propname
will be NULL, strcmp() called by of_get_property() will cause
null pointer dereference.
So return ENOMEM if kasprintf() return NULL pointer.
Fixes: 3afb50d7125b ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
__power_supply_register()
[ Upstream commit 5b79480ce1978864ac3f06f2134dfa3b6691fe74 ]
If device_add() succeeds, we should call device_del() when want to
get rid of it, so move it into proper jump symbol.
Otherwise, when __power_supply_register() returns fail and goto
wakeup_init_failed to exit, there is still residue device file in sysfs.
When attempt to probe device again, sysfs would complain as below:
sysfs: cannot create duplicate filename '/devices/platform/i2c/i2c-0/0-001c/power_supply/adp5061'
Call Trace:
dump_stack_lvl+0x68/0x85
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x1b1/0x1d0
kobject_add_internal+0x143/0x390
kobject_add+0x108/0x170
Fixes: 80c6463e2fa3 ("power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69460e68eb662064ab4188d4e129ff31c1f23ed9 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes: 984aa6dbf4ca ("OMAP3: PM: Adding smartreflex driver support.")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221108080322.52268-3-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d47e01b9d807808224347935562f7043a358054 ]
ADP5061_CHG_STATUS_1_CHG_STATUS is masked with 0x07, which means a length
of 8, but adp5061_chg_type array size is 4, may end up reading 4 elements
beyond the end of the adp5061_chg_type[] array.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80192eff64eee9b3bc0594a47381937b94b9d65a ]
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 0e545f57b708 ("power: reset: driver for the Versatile syscon reboot")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ac121b81b4051e7fc83d5b3456a5e499d5bd147 ]
The AXP288's recommended and factory default Vhold value (minimum
input voltage below which the input current draw will be reduced)
is 4.4V. This lines up with other charger IC's such as the TI
bq2419x/bq2429x series which use 4.36V or 4.44V.
For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V
which combined with the typical voltage drop over typically low
wire gauge micro-USB cables leads to the input-current getting
capped below 1A (with a 2A capable dedicated charger) based on Vhold.
This leads to slow charging, or even to the device slowly discharging
if the device is in heavy use.
As the Linux AXP288 drivers use the builtin BC1.2 charger detection
and send the input-current-limit according to the detected charger
there really is no reason not to use the recommended 4.4V Vhold.
Set Vhold to 4.4V to fix the slow charging issue on various devices.
There is one exception, the special-case of the HP X2 2-in-1s which
combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory
provided charger with a Type-C plug which does not do BC1.2. These
have their input-current-limit hardcoded to 3A (like under Windows)
and use a higher Vhold on purpose to limit the current when used
with other chargers. To avoid touching Vhold on these HP X2 laptops
the code setting Vhold is added to an else branch of the if checking
for these models.
Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK
define, which was wrong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4f408cdcd26921c1268cb8dcbe8ffb6faf837f3 ]
As stated in [1], negative current values are used for discharging
batteries.
AXP PMICs internally have two different ADC channels for shunt current
measurement: one used during charging and one during discharging.
The values reported by these ADCs are unsigned.
While the driver properly selects ADC channel to get the data from,
it doesn't apply negative sign when reporting discharging current.
[1] Documentation/ABI/testing/sysfs-class-power
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6dee930f6f6776d1e5a7edf542c6863b47d9f078 ]
In free_charger_irq(), there is no free for 'WM8350_IRQ_CHG_FAST_RDY'.
Therefore, it should be better to add it in order to avoid the memory leak.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0b14b5ba11bec56fad344a4a0b2e16449cc8b94 ]
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7731754fdce33dad19be746f647d6ac47c5d695 ]
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4e0 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6a4760463dbc6b603690938c468839985189ce0a ]
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: 8c0984e5a753 ("power: move power supply drivers to power/supply")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba18dad0fb880cd29aa97b6b75560ef14d1061ba ]
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: f7a388d6cd1c ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80211be1b9dec04cc2805d3d81e2091ecac289a1 ]
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 644106cdb89844be2496b21175b7c0c2e0fab381 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00cc ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: https://github.com/llvm/llvm-project/commit/a8083d42b1c346e21623a1d36d1f0cadd7801d83
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 51c7b6a0398f54b9120795796a4cff4fc9634f7d upstream.
We should not go on looking for more capacity tables after
we realize we have looked at the last one in
power_supply_find_ocv2cap_table().
Fixes: 3afb50d7125b ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cdf10ffe8f626d8a2edc354abf063df0078b2d71 ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c09795 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf895295e9a73411889816f1a0c1f4f1a2d9c678 ]
Currently the rt5033_battery driver provides voltage values in mV. It
should be µV as stated in Documentation/power/power_supply_class.rst.
Fixes: b847dd96e659 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 223a3b82834f036a62aa831f67cbf1f1d644c6e2 upstream.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b154 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e660dbb68c6b3f7b9eb8b9775846a44f9798b719 upstream.
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54784ffa5b267f57161eb8fbb811499f22a0a0bf upstream.
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc4f ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ed0d0a0506025f06061325cedae1bbebd081620a ]
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
errors
[ Upstream commit caa534c3ba40c6e8352b42cbbbca9ba481814ac8 ]
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3076cd8d1d5fa64b5e1fa5affc045c2fc123baa ]
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e659 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dfe52db13ab8d24857a9840ec7ca75eef800c26c ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 073b5d5b1f9cc94a3eea25279fbafee3f4f5f097 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed3443fb4df4e140a22f65144546c8a8e1e27f4e ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7fbf6b731bca347700e460d94b130f9d734b33e9 ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 17047/77693 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5bcb5087c9dd3dca1ff0ebd8002c5313c9332b56 ]
Sometimes the code will crash because we haven't enabled
AC or USB charging and thus not created the corresponding
psy device. Fix it by checking that it is there before
notifying.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2aac79d14d76879c8e307820b31876e315b1b242 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 603fcfb9d4ec1cad8d66d3bb37f3613afa8a661a ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
s3c_adc_bat_remove()
[ Upstream commit 68ae256945d2abe9036a7b68af4cc65aff79d5b7 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6cfa007b3b229771d9588970adb4ab3e0487f49 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2469b836fa835c67648acad17d62bc805236a6ea ]
Fixes coccicheck error:
drivers/power/supply/pm2301_charger.c:1089:7-27: ERROR:
drivers/power/supply/lp8788-charger.c:502:8-28: ERROR:
drivers/power/supply/tps65217_charger.c:239:8-33: ERROR:
drivers/power/supply/tps65090-charger.c:303:8-33: ERROR:
Threaded IRQ with no primary handler requested without IRQF_ONESHOT
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4d57c22ac65bd503716062a06fad55a01569cac ]
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Mario Limonciello
Marek Vasut
Hans de Goede
Daisuke Nojiri
Sebastian Reichel
Grant Grundler
Zheng Wang
ruanjinjie
Zeng Heng
Zhang Qilong
Wei Yongjun
Miaoqian Lin
Evgeny Boger
Jiasheng Jiang
Yauhen Kharuzhy
Nathan Chancellor
Linus Walleij
Jakob Hauser
Henrik Grimler
Sebastian Krzyszkowiak
Krzysztof Kozlowski
Stephan Gerhold
Zou Wei
Bixuan Cui
Krzysztof Kozlowski
Yang Yingliang
dongjian
Matthias Schiffer