| Age | Commit message (Collapse) | Author |
|---|
|
The boilerplate license is not necessary when the SPDX line is
present.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB Type-C class driver now expects the muxes to be always
assigned to the ports and not controllers, so the
connections for the mux and fusb302 can be removed.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Assigning the mux to the USB Type-C port on top of fusb302.
That will prepare this driver for the change in the USB
Type-C class code, where the class driver will assume the
muxes to be always assigned to the ports and not the
controllers.
Once the USB Type-C class driver has been updated, the
connections between the mux and fusb302 can be dropped.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding a connection for the DisplayPort alternate mode.
PI3USB30532 is used for muxing the port to DisplayPort on
CHT platforms. The connection allows the alternate mode
device to get handle to the mux, and therefore make it
possible to use the USB Type-C connector as DisplayPort.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We can register all device connection descriptors with a
single call to device_connections_add().
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The connections create clear dependency on the muxes.
fusb302 fails to probe unless we have the mux drivers
available.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the PCI hotplug core and its first user, cpqphp, were introduced in
February 2002 with historic commit a8a2069f432c, cpqphp allocated a slot
struct for its internal use plus a hotplug_slot struct to be registered
with the hotplug core and linked the two with pointers:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Nowadays, the predominant pattern in the tree is to embed ("subclass")
such structures in one another and cast to the containing struct with
container_of(). But it wasn't until July 2002 that container_of() was
introduced with historic commit ec4f214232cf:
https://git.kernel.org/tglx/history/c/ec4f214232cf
pnv_php, introduced in 2016, did the right thing and embedded struct
hotplug_slot in its internal struct pnv_php_slot, but all other drivers
cargo-culted cpqphp's design and linked separate structs with pointers.
Embedding structs is preferrable to linking them with pointers because
it requires fewer allocations, thereby reducing overhead and simplifying
error paths. Casting an embedded struct to the containing struct
becomes a cheap subtraction rather than a dereference. And having fewer
pointers reduces the risk of them pointing nowhere either accidentally
or due to an attack.
Convert all drivers to embed struct hotplug_slot in their internal slot
struct. The "private" pointer in struct hotplug_slot thereby becomes
unused, so drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
|
|
Ever since the PCI hotplug core was introduced in 2002, drivers had to
allocate and register a struct hotplug_slot_info for every slot:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Apparently the idea was that drivers furnish the hotplug core with an
up-to-date card presence status, power status, latch status and
attention indicator status as well as notify the hotplug core of changes
thereof. However only 4 out of 12 hotplug drivers bother to notify the
hotplug core with pci_hp_change_slot_info() and the hotplug core never
made any use of the information: There is just a single macro in
pci_hotplug_core.c, GET_STATUS(), which uses the hotplug_slot_info if
the driver lacks the corresponding callback in hotplug_slot_ops. The
macro is called when the user reads the attribute via sysfs.
Now, if the callback isn't defined, the attribute isn't exposed in sysfs
in the first place (see e.g. has_power_file()). There are only two
situations when the hotplug_slot_info would actually be accessed:
* If the driver defines ->enable_slot or ->disable_slot but not
->get_power_status.
* If the driver defines ->set_attention_status but not
->get_attention_status.
There is no driver doing the former and just a single driver doing the
latter, namely pnv_php.c. Amend it with a ->get_attention_status
callback. With that, the hotplug_slot_info becomes completely unused by
the PCI hotplug core. But a few drivers use it internally as a cache:
cpcihp uses it to cache the latch_status and adapter_status.
cpqhp uses it to cache the adapter_status.
pnv_php and rpaphp use it to cache the attention_status.
shpchp uses it to cache all four values.
Amend these drivers to cache the information in their private slot
struct. shpchp's slot struct already contains members to cache the
power_status and adapter_status, so additional members are only needed
for the other two values. In the case of cpqphp, the cached value is
only accessed in a single place, so instead of caching it, read the
current value from the hardware.
Caution: acpiphp, cpci, cpqhp, shpchp, asus-wmi and eeepc-laptop
populate the hotplug_slot_info with initial values on probe. That code
is herewith removed. There is a theoretical chance that the code has
side effects without which the driver fails to function, e.g. if the
ACPI method to read the adapter status needs to be executed at least
once on probe. That seems unlikely to me, still maintainers should
review the changes carefully for this possibility.
Rafael adds: "I'm not aware of any case in which it will break anything,
[...] but if that happens, it may be necessary to add the execution of
the control methods in question directly to the initialization part."
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
|
|
Hotplug drivers cannot declare their hotplug_slot_ops const, making them
attractive targets for attackers, because upon registration of a hotplug
slot, __pci_hp_initialize() writes to the "owner" and "mod_name" members
in that struct.
Fix by moving these members to struct hotplug_slot and constify every
driver's hotplug_slot_ops except for pciehp.
pciehp constructs its hotplug_slot_ops at runtime based on the PCIe
port's capabilities, hence cannot declare them const. It can be
converted to __write_rarely once that's mainlined:
http://www.openwall.com/lists/kernel-hardening/2016/11/16/3
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
|
|
checkpatch: Comparison to NULL could be written "!x"
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch: Logical continuations should be on the previous line
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch: Alignment should match open parenthesis.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch: Lines should not end with a '(' or '['
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add "pipe" to the pipe related function names.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Casting to (void) is no-op.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch: Avoid CamelCase
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Casting to u32 is not required here.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two function calls look cleaner because the function introduces
takes case of all bit shifting and casting.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable was not very useful.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To improve readability and to be consistent with other
struct members.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dev_ is preferred if struct device is available.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no reason to have an array of 1.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the driver provides no workaround prevent in cases if structs do
no fit into a memory page, it is better to fail complation to find about
the issue earlt instead of returning errors at runtime.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Provide an explanation why GFP_ATOMIC is needed to prevent changing it to
other values.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These are several enums that must kept in sync with the host side.
This change explicitly separates them into a dedicated header file.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch: Function's opening brace has to be at the
beginning of the next line.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
goldfish_pipe is distributed under GPL v2.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some comment lines are longer than 80 symbols.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An ACPI buffer that was allocated was not being freed after use.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
ACPI buffers were being allocated but never freed.
Reported-by: Pinzhen Xu <pinzhen.xu@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
The cros-ec-lpc driver lives in drivers/platform because is platform
specific, however there are two includes (cros_ec_lpc_mec.h and
cros_ec_lpc_reg.h) that lives in include/linux/mfd. These two includes
are only used for the platform driver and are not really related to the
MFD subsystem, so move the includes from include/linux/mfd to
drivers/platform/chrome.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The driver for Silead touchscreen configurations has been renamed
from silead_dmi to touchscreen_dmi since it starts supporting other
touchscreens which require some DMI quirks
It also gets expanded to cover cases for Chuwi Vi10, ONDA V891W,
Connect Tablet 9, Onda V820w, and Cube KNote i1101 tablets.
- Another bunch of changes is related to Mellanox platform code to
allow user space to communicate with Mellanox for system control and
monitoring purposes. The driver notifies user on hotplug device
signal receiving.
- ASUS WMI drivers recognize lid flip action on UX360, and correctly
toggles airplane mode LED. In addition the keyboard backlight toggle
gets support.
- ThinkPad ACPI driver enables support for calculator key (on at least
P52). It also has been fixed to support three characters model
designators, which are used for modern laptops. Earlier the battery,
marked as BAT1, on ThinkPad laptops has not been configured properly,
which is fixed. On the opposite the multi-battery configurations now
probed correctly.
- Dell SMBIOS driver starts working on some Dell servers which do not
support token interface. The regression with backlight detection has
also been fixed. In order to support dock mode on some laptops, Intel
virtual button driver has been fixed. The last but not least is the
fix to Intel HID driver due to changes in Dell systems that prevented
to use power button.
* tag 'platform-drivers-x86-v4.19-1' of git://git.infradead.org/linux-platform-drivers-x86: (47 commits)
platform/x86: acer-wmi: Silence "unsupported" message a bit
platform/x86: intel_punit_ipc: fix build errors
platform/x86: ideapad: Add Y520-15IKBM and Y720-15IKBM to no_hw_rfkill
platform/x86: asus-nb-wmi: Add keymap entry for lid flip action on UX360
platform/x86: acer-wmi: refactor function has_cap
platform/x86: thinkpad_acpi: Fix multi-battery bug
platform/x86: thinkpad_acpi: extend battery quirk coverage
platform/x86: touchscreen_dmi: Add info for the Cube KNote i1101 tablet
platform/x86: mlx-platform: Fix copy-paste error in mlxplat_init()
platform/x86: mlx-platform: Remove unused define
platform/x86: mlx-platform: Change mlxreg-io configuration for MSN274x systems
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for more systems
platform/x86: mlx-platform: Add ASIC hotplug device configuration
platform/mellanox: mlxreg-hotplug: Add hotplug hwmon uevent notification
platform/mellanox: mlxreg-hotplug: Improve mechanism of ASIC health discovery
platform/x86: mlx-platform: Add mlxreg-fan platform driver activation
platform/x86: dell-laptop: Fix backlight detection
platform/x86: toshiba_acpi: Fix defined but not used build warnings
platform/x86: thinkpad_acpi: Support battery quirk
...
|
|
This driver prints that "Unsupported machine..." message on every boot on
ThinkPad X1 Carbon laptops (and I assume a number of other systems), which
causes graphical boots to "glitch" a bit and is rather annoying ...
Make it a pr_debug instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull core signal handling updates from Eric Biederman:
"It was observed that a periodic timer in combination with a
sufficiently expensive fork could prevent fork from every completing.
This contains the changes to remove the need for that restart.
This set of changes is split into several parts:
- The first part makes PIDTYPE_TGID a proper pid type instead
something only for very special cases. The part starts using
PIDTYPE_TGID enough so that in __send_signal where signals are
actually delivered we know if the signal is being sent to a a group
of processes or just a single process.
- With that prep work out of the way the logic in fork is modified so
that fork logically makes signals received while it is running
appear to be received after the fork completes"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (22 commits)
signal: Don't send signals to tasks that don't exist
signal: Don't restart fork when signals come in.
fork: Have new threads join on-going signal group stops
fork: Skip setting TIF_SIGPENDING in ptrace_init_task
signal: Add calculate_sigpending()
fork: Unconditionally exit if a fatal signal is pending
fork: Move and describe why the code examines PIDNS_ADDING
signal: Push pid type down into complete_signal.
signal: Push pid type down into __send_signal
signal: Push pid type down into send_signal
signal: Pass pid type into do_send_sig_info
signal: Pass pid type into send_sigio_to_task & send_sigurg_to_task
signal: Pass pid type into group_send_sig_info
signal: Pass pid and pid type into send_sigqueue
posix-timers: Noralize good_sigevent
signal: Use PIDTYPE_TGID to clearly store where file signals will be sent
pid: Implement PIDTYPE_TGID
pids: Move the pgrp and session pid pointers from task_struct to signal_struct
kvm: Don't open code task_pid in kvm_vcpu_ioctl
pids: Compute task_tgid using signal->leader_pid
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung.
Everything but the SPDX identifier updates actually came in earlier
through the MFD merge.
* tag 'chrome-platform-for-linus-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: chromeos_tbmc - fix SPDX identifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
|
|
Fix build errors by #including <linux/io.h>.
../drivers/platform/x86/intel_punit_ipc.c: In function 'ipc_read_status':
../drivers/platform/x86/intel_punit_ipc.c:55:2: error: implicit declaration of function 'readl' [-Werror=implicit-function-declaration]
return readl(ipcdev->base[type][BASE_IFACE]);
../drivers/platform/x86/intel_punit_ipc.c: In function 'ipc_write_cmd':
../drivers/platform/x86/intel_punit_ipc.c:60:2: error: implicit declaration of function 'writel' [-Werror=implicit-function-declaration]
writel(cmd, ipcdev->base[type][BASE_IFACE]);
Fixes: 447ae3166702 ("x86: Don't include linux/irq.h from asm/hardirq.h")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Zha Qipeng <qipeng.zha@intel.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Socionext MN88443x ISDB-S/T demodulator driver: mn88443x
- new sensor drivers: ak7375, ov2680 and rj54n1cb0c
- an old soc-camera sensor driver converted to the V4L2 framework:
mt9v111
- a new Voice-Coil Motor (VCM) driver: dw9807-vcm
- some cleanups at cx25821, removing legacy unused code
- some improvements at ddbridge driver
- new platform driver: vicodec
- some DVB API cleanups, removing ioctls and compat code for old
out-of-tree drivers that were never merged upstream
- improvements at DVB core to support frontents that support both
Satellite and non-satellite delivery systems
- got rid of the unused VIDIOC_RESERVED V4L2 ioctl
- some cleanups/improvements at gl861 ISDB driver
- several improvements on ov772x, ov7670 and ov5640, imx274, ov5645,
and smiapp sensor drivers
- fixes at em28xx to support dual TS devices
- some cleanups at V4L2/VB2 locking logic
- some API improvements at media controller
- some cec core and drivers improvements
- some uvcvideo improvements
- some improvements at platform drivers: stm32-dcmi, rcar-vin, coda,
reneseas-ceu, imx, vsp1, venus, camss
- lots of other cleanups and fixes
* tag 'media/v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (406 commits)
Revert "media: vivid: shut up warnings due to a non-trivial logic"
siano: get rid of an unused return code for debugfs register
media: isp: fix a warning about a wrong struct initializer
media: radio-wl1273: fix return code for the polling routine
media: s3c-camif: fix return code for the polling routine
media: saa7164: fix return codes for the polling routine
media: exynos-gsc: fix return code if mutex was interrupted
media: mt9v111: Fix build error with no VIDEO_V4L2_SUBDEV_API
media: xc4000: get rid of uneeded casts
media: drxj: get rid of uneeded casts
media: tuner-xc2028: don't use casts for printing sizes
media: cleanup fall-through comments
media: vivid: shut up warnings due to a non-trivial logic
media: rtl28xxu: be sure that it won't go past the array size
media: mt9v111: avoid going past the buffer
media: vsp1_dl: add a description for cmdpool field
media: sta2x11: add a missing parameter description
media: v4l2-mem2mem: add descriptions to MC fields
media: i2c: fix warning in Aptina MT9V111
media: imx: shut up a false positive warning
...
|
|
Lenovo Y520-15IKBM and Y720-15IKBM are another Lenovo models
without physical radio switch and ideapad-laptop reports it
is hard blocked. Add them into no_hw_rfkill to unlock wireless.
BugLink: https://bugs.launchpad.net/bugs/1723612
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add entry to WMI keymap for lid flip event on Asus UX360.
On Asus Zenbook ux360 flipping lid from/to tablet mode triggers
keyscan code 0xfa which cannot be handled and results in kernel
log message "Unknown key fa pressed".
Signed-off-by: Aleh Filipovich<aleh@appnexus.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Refactor function has_cap in order to avoid returning integer
values, when instead it should return booleans.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The struct containing the supported operations for all batteries is
being zeroed on each battery probe. This prevents all other batteries
except the lastly probed one from being configured.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Based on bug reports and a web search for
"Thinkpad_acpi: Error probing battery 2"
four more models were found that require the battery quirk:
Lenovo B5400, Thinkpad 11e, Thinkpad 11e gen 3, Thinkpad 13 gen 3.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Tested-by: James Cheshire <jermizzey@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen info for the Cube KNote i1101 tablet.
Reported-and-tested-by: lkongl <lkongl@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The return value from platform_device_register_resndata() is not checked
correctly. The test is done against a wrong variable. This patch fix it.
Fixes: 0378123c5800 ("platform/x86: mlx-platform: Add mlxreg-fan platform driver activation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These revert two ACPICA commits that are not needed any more, rework
the property graphs support in ACPI to be more aligned with the
analogous DT code, add some new quirks and remove one that isn't
needed any more, add a special platform driver to enumerate multiple
I2C devices hooked up to the same device object in the ACPI tables and
update the battery and button drivers.
Specifics:
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code and
update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization to
ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma, Mika
Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy
Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd)"
* tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
platform/x86: Add ACPI i2c-multi-instantiate pseudo driver
ACPI / x86: utils: Remove status workaround from acpi_device_always_present()
ACPI / scan: Create platform device for fwnodes with multiple i2c devices
ACPI / scan: Initialize status to ACPI_STA_DEFAULT
ACPI / EC: Add another entry for Thinkpad X1 Carbon 6th
ACPI: bus: Fix a pointer coding style issue
arm64 / ACPI: clean the additional checks before calling ghes_notify_sea()
ACPI / scan: Add static attribute to indirect_io_hosts[]
ACPI / battery: Do not export energy_full[_design] on devices without full_charge_capacity
ACPI / EC: Use ec_no_wakeup on ThinkPad X1 Yoga 3rd
ACPI / battery: get rid of negations in conditions
ACPI / battery: use specialized print macros
ACPI / battery: reorder headers alphabetically
ACPI / battery: drop inclusion of init.h
ACPI: battery: remove redundant old_present check on insertion
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Here are the main MIPS changes for 4.19.
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes &
corresponding regsets to expose DSP ASE & floating point mode state
respectively, both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where
it was previously possible for CPUs to clobber a register value
saved by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which now
sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build
failures for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for
systems where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than
MIPSr2 to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code"
* tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (123 commits)
MIPS: Remove remnants of UASM_ISA
MIPS: netlogic: xlr: Remove erroneous check in nlm_fmn_send()
MIPS: VDSO: Force link endianness
MIPS: Always specify -EB or -EL when using clang
MIPS: Use dins to simplify __write_64bit_c0_split()
MIPS: Use read-write output operand in __write_64bit_c0_split()
MIPS: Avoid using array as parameter to write_c0_kpgd()
MIPS: vdso: Allow clang's --target flag in VDSO cflags
MIPS: genvdso: Remove GOT checks
MIPS: Remove obsolete MIPS checks for DST node "chosen@0"
MIPS: generic: Remove input symbols from defconfig
MIPS: Delete unused code in linux32.c
MIPS: Remove unused sys_32_mmap2
MIPS: Remove nabi_no_regargs
mips: dts: mscc: enable spi and NOR flash support on ocelot PCB123
mips: dts: mscc: Add spi on Ocelot
MIPS: Loongson: Merge load addresses
MIPS: Loongson: Set Loongson32 to MIPS32R1
MIPS: mscc: ocelot: add interrupt controller properties to GPIO controller
MIPS: generic: Select MIPS_AUTO_PFN_OFFSET
...
|
Roman Kiryanov
Heikki Krogerus
Lukas Wunner
Mario Limonciello
Enric Balletbo i Serra
Linus Torvalds
Benjamin Herrenschmidt
Randy Dunlap
Ike Panhc
Aleh Filipovich
Gustavo A. R. Silva
Thomas Weißschuh
Jouke Witteveen
youling257
Wei Yongjun