| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit cb0438e4436085d89706b5ccfce4d5da531253de ]
Hi i tried to use the uart_C of the the odroid-c2.
I enabled it in the dts file. During boot it crashed when the
the sdcard slot is addressed.
After long search in the net i found this:
https://forum.odroid.com/viewtopic.php?f=139&t=25371&p=194370&hilit=uart_C#p177856
After changing the pin definitions accordingly erverything works.
Uart_c is functioning and sdcard ist working.
Fixes: 6db0f3a8a04e46 ("pinctrl: amlogic: gxbb: add more UART pins")
Signed-off-by: Otto Meier <gf435@gmx.net>
Link: https://lore.kernel.org/r/1cc32a18-464d-5531-7a1c-084390e2ecb1@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4bc51e1e350cd4707ce6e551a93eae26d40b9889 ]
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 468c234f9ed7 ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Add the pinctrl configuration for gen_clk on gxbb and axg.
gen_clk allows to output and devide several internal clocks of SoC,
including most of the plls.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The data pin 0-7 of the NAND controller are actually missing from
the nand pinctrl group, so we fix it here.
Fixes: cd1e3b01c7d3 ("pinctrl: amlogic: gxbb: add nand pins")
Reported-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This change prepare the introduction of new meson SoC. This new SoC will
share the same gpio/pinconf registers but the pinmux part will be
different. While the format of the data associated with each pinmux group
will change, the way to handle pinmuxing will be similar.
To deal with this new situation, the meson_pmx_struture is kept but the
data associated to it is now generic. This allows to reuse the basic
functions which would otherwise be copy/pasted in each pinmux driver
(such as getting the name a count of groups and functions) Only the
functions actually using this specific data is taken out of the common
code and is handling the SoC pinmuxing
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.
This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.
This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add TEST_N pinmux for channel 6 and 7 of the i2s output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIOX_22 is declared as a gpio but the id is no present in the pin
table. This hole trigger an error while reading the pingroup debugfs entry
GPIOX_22 is no routed externally. For all we know, it could an internal
pin of SoC
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On meson-gx platforms, TEST_N has been incorrectly declared in the EE
controller while it belongs to AO controller.
Move the pin to the appropriate controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pin_base was used with the manually set pin offset in meson pinctrl. This
is no longer the case, pin_base is 0 on every meson pinctrl controllers
and should go away.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.
This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add GPIO interrupt information to pinctrl data. Added to the original
version from Jerome was data for Meson GXL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After commit 34e61801a3b9 "pinctrl: meson-gxbb: Add missing GPIODV_18
pin entry" I started to get the following warning:
"meson-pinctrl c8834000.periphs:pinctrl@4b0: names 119 do not match
number of GPIOs 120"
It turned out that not the mentioned commit has a problem, it just
revealed another problem which had existed before.
There is no PIN GPIOX_22 on Meson GXBB.
Fixes: 468c234f9ed7 ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the AO and EE domain CEC pins for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIODV_18 entry was missing in the original driver push.
Fixes: 468c234f9ed7 ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXBB pinctrl driver
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
|
|
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.10-rc6
Resolved conflicts in:
drivers/pinctrl/pinctrl-amd.c
drivers/pinctrl/samsung/pinctrl-exynos.c
|
|
The GXBB and GXL/GXM pinctrl drivers had a configuration which conflicts
with uart_ao_a. According to the GXBB ("S905") datasheet the AO UART
functions are:
- GPIOAO_0: Func1 = UART_TX_AO_A (bit 12), Func2 = UART_TX_AO_B (bit 26)
- GPIOAO_1: Func1 = UART_RX_AO_A (bit 11), Func2 = UART_RX_AO_B (bit 25)
- GPIOAO_4: Func2 = UART_TX_AO_B (bit 24)
- GPIOAO_5: Func2 = UART_RX_AO_B (bit 25)
The existing definition for uart_AO_A already uses GPIOAO_0 and GPIOAO_1.
The old definition of uart_AO_B however was broken, as it used GPIOAO_0
for TX (which would be fine) and two pins (GPIOAO_1 and GPIOAO_5) for RX
(which does not make any sense).
This fixes the uart_AO_B configuration by moving it to GPIOAO_4 and
GPIOAO_5 (it would be possible to use GPIOAO_0 and GPIOAO_1 in theory,
but all existing hardware uses uart_AO_A there).
The fix for GXBB and GXL/GXM is identical since it seems that these
specific pins are identical on both SoC variants.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pinctrl functions for HDMI HPD pin and DDC pins on Amlogic Meson
GXL and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domains pins for the i2c devices A,B,C
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domains pins for the NAND flash controller.
Even tough we have no driver for the NAND flash controller yet, we need
to have these pins in pinctrl as the actual pin are shared with the spifc
controller. The bootloader on the S905-P200 setup pinmux for the NAND
controller so we need the kernel to properly deactivate this if necessary.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domains pins for the SPI flash controller
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the SDIO interrupt pin which can be used by sd_emmc_a.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: 29885a656511 ("pinctrl: meson-gxbb: add the pins for the
SDIO/sd_emmc_a controller")
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sd_emmc_a is used a controller for the SDIO modules. This adds the pin
configuration for the SDIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for PWM pins, for EE and AO domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the IR remote receiver to the AO domain devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver originally supported more domains (register ranges) per
pinctrl device, but since commit 9dab1868ec0d ("pinctrl: amlogic: Make
driver independent from two-domain configuration") each device gets
assigned a single domain and we instantiate multiple pinctrl devices
in the DT.
Therefore, now the 'meson_domain' and 'meson_domain_data' structures
don't have any reason to exist and can be removed to make the model
simpler to understand. This commit doesn't change behavior.
Tested on a Odroid-C2.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domain pins for ethernet interface.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domain pins for UART A, B & C.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domain pins for eMMC and SD card.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pins for some more AO domain devices: UART_AO_B and I2C master &
slave.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds the basic platform file to support the pin controller
found on the Amlogic Meson GXBB SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Otto Meier
Jerome Brunet
Yixun Lan
Heiner Kallweit
Neil Armstrong
Linus Torvalds
Linus Walleij
Martin Blumenstingl
Beniamino Galvani
Kevin Hilman
Carlo Caione