| Age | Commit message (Collapse) | Author |
|---|
|
commit 4ec73791a64bab25cabf16a6067ee478692e506d upstream.
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 86fa6a344209d9414ea962b1f1ac6ade9dd7563a upstream.
Factor out pcie_retrain_link() to use for Pericom Retrain Link quirk. No
functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be20bbcb0a8cb5597cc62b3e28d275919f3431df upstream.
Reestablish the PCIe link very early in the resume process in case it
went down to prevent PCI accesses from hanging the bus. Such accesses
can happen early in the PCI resume process, as early as the
SUSPEND_RESUME_NOIRQ step, thus the link must be reestablished in the
driver resume_noirq() callback.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[lorenzo.pieralisi@arm.com: reformatted commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31f996efbd5a7825f4d30150469e9d110aea00e8 upstream.
Commit 60ed982a4e78 ("PCI/AER: Move internal declarations to
drivers/pci/pci.h") changed pci_aer_init() to return "void", but didn't
change the stub for when CONFIG_PCIEAER isn't enabled. Change the stub to
match.
Fixes: 60ed982a4e78 ("PCI/AER: Move internal declarations to drivers/pci/pci.h")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6302bf3ef78dd210b5ff4a922afcb7d8eff8a211 upstream.
Two functions allocate a host bridge: devm_pci_alloc_host_bridge() and
pci_alloc_host_bridge(). At the moment, only the unmanaged one initializes
the PCIe feature bits, which prevents from using features such as hotplug
or AER on some systems, when booting with device tree. Make the
initialization code common.
Fixes: 02bfeb484230 ("PCI/portdrv: Simplify PCIe feature permission checking")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6afb7e26978da5e86e57e540fdce65c8b04f398a upstream.
When using PCI passthrough with this device, the host machine locks up
completely when starting the VM, requiring a hard reboot. Add a quirk to
avoid bus resets on this device.
Fixes: c3e59ee4e766 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.com
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d28ca864c493637f3c957f4ed9348a94fca6de60 upstream.
ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop)
and causes IOMMU stalls and system failure. Disable ATS on these devices
to make them usable again with IOMMU enabled.
Thanks to Joerg Roedel <jroedel@suse.de> for help.
[bhelgaas: In the email thread mentioned below, Alex suspects the real
problem is in sbios or iommu, so it may affect only certain systems, and it
may affect other devices in those systems as well. However, per Joerg we
lack the ability to debug further, so this quirk is the best we can do for
now.]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521
Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org
Fixes: 9b44b0b09dec ("PCI: Mark AMD Stoney GPU ATS as broken")
Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 340d455699400f2c2c0f9b3f703ade3085cdb501 upstream.
When we hot-remove a device, usually the host sends us a PCI_EJECT message,
and a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
When we execute the quick hot-add/hot-remove test, the host may not send
us the PCI_EJECT message if the guest has not fully finished the
initialization by sending the PCI_RESOURCES_ASSIGNED* message to the
host, so it's potentially unsafe to only depend on the
pci_destroy_slot() in hv_eject_device_work() because the code path
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
is not called in this case. Note: in this case, the host still sends the
guest a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
In the quick hot-add/hot-remove test, we can have such a race before
the code path
pci_devices_present_work()
-> new_pcichild_device()
adds the new device into the hbus->children list, we may have already
received the PCI_EJECT message, and since the tasklet handler
hv_pci_onchannelcallback()
may fail to find the "hpdev" by calling
get_pcichild_wslot(hbus, dev_message->wslot.slot)
hv_pci_eject_device() is not called; Later, by continuing execution
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
creates the slot and the PCI_BUS_RELATIONS message with
bus_rel->device_count == 0 removes the device from hbus->children, and
we end up being unable to remove the slot in
hv_pci_remove()
-> hv_pci_remove_slots()
Remove the slot in pci_devices_present_work() when the device
is removed to address this race.
pci_devices_present_work() and hv_eject_device_work() run in the
singled-threaded hbus->wq, so there is not a double-remove issue for the
slot.
We cannot offload hv_pci_eject_device() from hv_pci_onchannelcallback()
to the workqueue, because we need the hv_pci_onchannelcallback()
synchronously call hv_pci_eject_device() to poll the channel
ringbuffer to work around the "hangs in hv_compose_msi_msg()" issue
fixed in commit de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in
hv_compose_msi_msg()")
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: rewritten commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15becc2b56c6eda3d9bf5ae993bafd5661c1fad1 upstream.
When we unload the pci-hyperv host controller driver, the host does not
send us a PCI_EJECT message.
In this case we also need to make sure the sysfs PCI slot directory is
removed, otherwise a command on a slot file eg:
"cat /sys/bus/pci/slots/2/address"
will trigger a
"BUG: unable to handle kernel paging request"
and, if we unload/reload the driver several times we would end up with
stale slot entries in PCI slot directories in /sys/bus/pci/slots/
root@localhost:~# ls -rtl /sys/bus/pci/slots/
total 0
drwxr-xr-x 2 root root 0 Feb 7 10:49 2
drwxr-xr-x 2 root root 0 Feb 7 10:49 2-1
drwxr-xr-x 2 root root 0 Feb 7 10:51 2-2
Add the missing code to remove the PCI slot and fix the current
behaviour.
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: reformatted the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05f151a73ec2b23ffbff706e5203e729a995cdc2 upstream.
When a device is created in new_pcichild_device(), hpdev->refs is set
to 2 (i.e. the initial value of 1 plus the get_pcichild()).
When we hot remove the device from the host, in a Linux VM we first call
hv_pci_eject_device(), which increases hpdev->refs by get_pcichild() and
then schedules a work of hv_eject_device_work(), so hpdev->refs becomes
3 (let's ignore the paired get/put_pcichild() in other places). But in
hv_eject_device_work(), currently we only call put_pcichild() twice,
meaning the 'hpdev' struct can't be freed in put_pcichild().
Add one put_pcichild() to fix the memory leak.
The device can also be removed when we run "rmmod pci-hyperv". On this
path (hv_pci_remove() -> hv_pci_bus_exit() -> hv_pci_devices_present()),
hpdev->refs is 2, and we do correctly call put_pcichild() twice in
pci_devices_present_work().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log rework]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2c4db1bd80720cd8cb2a5aa220d9bc9f374f04e upstream
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 85b0cae89d5266e6a7abb2e83c6f716326fc494c ]
Gigabyte X299 DESIGNARE EX motherboard has one PCIe root port that is
connected to an Alpine Ridge Thunderbolt controller. This port has slot
implemented bit set in the config space but other than that it is not
hotplug capable in the sense we are expecting in Linux (it has
dev->is_hotplug_bridge set to 0):
00:1c.4 PCI bridge: Intel Corporation 200 Series PCH PCI Express Root Port #5
Bus: primary=00, secondary=05, subordinate=46, sec-latency=0
Memory behind bridge: 78000000-8fffffff [size=384M]
Prefetchable memory behind bridge: 00003800f8000000-00003800ffffffff [size=128M]
...
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
...
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #8, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState+
This system is using ACPI based hotplug to notify the OS that it needs to
rescan the PCI bus (ACPI hotplug).
If there is nothing connected in any of the Thunderbolt ports the root port
will not have any runtime PM active children and is thus automatically
runtime suspended pretty soon after boot by PCI PM core. Now, when a
device is connected the BIOS SMI handler responsible for enumerating newly
added devices is not able to find anything because the port is in D3.
Prevent this from happening by blacklisting PCI power management of this
particular Gigabyte system.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202031
Reported-by: Kedar A Dongre <kedar.a.dongre@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3943af9d01e94330d0cfac6fccdbc829aad50c92 upstream.
During a safe hot remove, the OS powers off the slot, which may cause a
Data Link Layer State Changed event. The slot has already been set to
OFF_STATE, so that event results in re-enabling the device, making it
impossible to safely remove it.
Clear out the Presence Detect Changed and Data Link Layer State Changed
events when the disabled slot has settled down.
It is still possible to re-enable the device if it remains in the slot
after pressing the Attention Button by pressing it again.
Fixes the problem that Micah reported below: an NVMe drive power button may
not actually turn off the drive.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203237
Reported-by: Micah Parrish <micah.parrish@hpe.com>
Tested-by: Micah Parrish <micah.parrish@hpe.com>
Signed-off-by: Sergey Miroshnichenko <s.miroshnichenko@yadro.com>
[bhelgaas: changelog, add bugzilla URL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cde402a59770a0669d895399c13407f63d7d209 upstream.
There is a Marvell 88SE9170 PCIe SATA controller I found on a board here.
Some quick testing with the ARM SMMU enabled reveals that it suffers from
the same requester ID mixup problems as the other Marvell chips listed
already.
Add the PCI vendor/device ID to the list of chips which need the
workaround.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 95c80bc6952b6a5badc7b702d23e5bf14d251e7c ]
Dongdong reported a deadlock triggered by a hotplug event during a sysfs
"remove" operation:
pciehp 0000:00:0c.0:pcie004: Slot(0-1): Link Up
# echo 1 > 0000:00:0c.0/remove
PME and hotplug share an MSI/MSI-X vector. The sysfs "remove" side is:
remove_store
pci_stop_and_remove_bus_device_locked
pci_lock_rescan_remove
pci_stop_and_remove_bus_device
...
pcie_pme_remove
pcie_pme_suspend
synchronize_irq # wait for hotplug IRQ handler
pci_unlock_rescan_remove
The hotplug side is:
pciehp_ist
pciehp_handle_presence_or_link_change
pciehp_configure_device
pci_lock_rescan_remove # wait for pci_unlock_rescan_remove()
INFO: task bash:10913 blocked for more than 120 seconds.
# ps -ax |grep D
PID TTY STAT TIME COMMAND
10913 ttyAMA0 Ds+ 0:00 -bash
14022 ? D 0:00 [irq/745-pciehp]
# cat /proc/14022/stack
__switch_to+0x94/0xd8
pci_lock_rescan_remove+0x20/0x28
pciehp_configure_device+0x30/0x140
pciehp_handle_presence_or_link_change+0x324/0x458
pciehp_ist+0x1dc/0x1e0
# cat /proc/10913/stack
__switch_to+0x94/0xd8
synchronize_irq+0x8c/0xc0
pcie_pme_suspend+0xa4/0x118
pcie_pme_remove+0x20/0x40
pcie_port_remove_service+0x3c/0x58
...
pcie_port_device_remove+0x2c/0x48
pcie_portdrv_remove+0x68/0x78
pci_device_remove+0x48/0x120
...
pci_stop_bus_device+0x84/0xc0
pci_stop_and_remove_bus_device_locked+0x24/0x40
remove_store+0xa4/0xb8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit c7b5a4e6e8fb ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes: c7b5a4e6e8fb ("PCI / PM: Fix native PME handling during system suspend/resume")
Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3afc8299f39a27b60e1519a28e18878ce878e7dd upstream.
Since 7c5925afbc58 (PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API) the MSI init claims one of the controller IRQs as a
chained IRQ line for the MSI controller. On some designs, like the i.MX6,
this line is shared with a PCIe legacy IRQ. When the line is claimed for
the MSI domain, any device trying to use this legacy IRQs will fail to
request this IRQ line.
As MSI and legacy IRQs are already mutually exclusive on the DWC core,
as the core won't forward any legacy IRQs once any MSI has been enabled,
users wishing to use legacy IRQs already need to explictly disable MSI
support (usually via the pci=nomsi kernel commandline option). To avoid
any issues with MSI conflicting with legacy IRQs, just skip all of the
DWC MSI initalization, including the IRQ line claim, when MSI is disabled.
Fixes: 7c5925afbc58 ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f08a5d896ce43380314c34ed3f264c8e6075b80 upstream.
Previously dpc_handler() called aer_get_device_error_info() without
initializing info->severity, so aer_get_device_error_info() relied on
uninitialized data.
Add dpc_get_aer_uncorrect_severity() to read the port's AER status, mask,
and severity registers and set info->severity.
Also, clear the port's AER fatal error status bits.
Fixes: 8aefa9b0d910 ("PCI/DPC: Print AER status in DPC event handling")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10ecc818ea7319b5d0d2b4e1aa6a77323e776f76 upstream.
RussianNeuroMancer reported that the Intel 7265 wifi on a Dell Venue 11 Pro
7140 table stopped working after wakeup from suspend and bisected the
problem to 9ab105deb60f ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't
have LTR"). David Ward reported the same problem on a Dell Latitude 7350.
After af8bb9f89838 ("PCI/ACPI: Request LTR control from platform before
using it"), we don't enable LTR unless the platform has granted LTR control
to us. In addition, we don't notice if the platform had already enabled
LTR itself.
After 9ab105deb60f ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't have
LTR"), we avoid using LTR if we don't think the path to the device has LTR
enabled.
The combination means that if the platform itself enables LTR but declines
to give the OS control over LTR, we unnecessarily avoided using ASPM L1.2.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201469
Fixes: 9ab105deb60f ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't have LTR")
Fixes: af8bb9f89838 ("PCI/ACPI: Request LTR control from platform before using it")
Reported-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Reported-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2fd6e81912a665993b24dcdc1c1384a42a54f7e upstream.
The disable_acs_redir parameter stores a pointer to the string passed to
pci_setup(). However, the string passed to PCI setup is actually a
temporary copy allocated in static __initdata memory. After init, once the
memory is freed, it is no longer valid to reference this pointer.
This bug was noticed in v5.0-rc1 after a change in commit c5eb1190074c
("PCI / PM: Allow runtime PM without callback functions") caused
pci_disable_acs_redir() to be called during shutdown which manifested
as an unable to handle kernel paging request at:
RIP: 0010:pci_enable_acs+0x3f/0x1e0
Call Trace:
pci_restore_state.part.44+0x159/0x3c0
pci_restore_standard_config+0x33/0x40
pci_pm_runtime_resume+0x2b/0xd0
? pci_restore_standard_config+0x40/0x40
__rpm_callback+0xbc/0x1b0
rpm_callback+0x1f/0x70
? pci_restore_standard_config+0x40/0x40
rpm_resume+0x4f9/0x710
? pci_conf1_read+0xb6/0xf0
? pci_conf1_write+0xb2/0xe0
__pm_runtime_resume+0x47/0x70
pci_device_shutdown+0x1e/0x60
device_shutdown+0x14a/0x1f0
kernel_restart+0xe/0x50
__do_sys_reboot+0x1ee/0x210
? __fput+0x144/0x1d0
do_writev+0x5e/0xf0
? do_writev+0x5e/0xf0
do_syscall_64+0x48/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
It was also likely possible to trigger this bug when hotplugging PCI
devices.
To fix this, instead of storing a pointer, we use kstrdup() to copy the
disable_acs_redir_param to its own buffer which will never be freed.
Fixes: aaca43fda742 ("PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support")
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 75cb8d20c112aba70f23d98e3f8d0a38ace16006 ]
The MSI Enable bit in the MSI Capability (PCIe r4.0, sec 7.7.1.2) controls
whether a Function can request service using MSI.
i.MX6 Root Ports implement the MSI Capability and may use MSI to request
service for events like PME, hotplug, AER, etc. In addition, on i.MX6, the
MSI Enable bit controls delivery of MSI interrupts from components below
the Root Port.
Prior to f3fdfc4ac3a2 ("PCI: Remove host driver Kconfig selection of
CONFIG_PCIEPORTBUS"), enabling CONFIG_PCI_IMX6 automatically also enabled
CONFIG_PCIEPORTBUS, and when portdrv claimed the Root Ports, it set the MSI
Enable bit so it could use PME, hotplug, AER, etc. As a side effect, that
also enabled delivery of MSI interrupts from downstream components.
The imx6q-pcie driver itself does not depend on portdrv, so set MSI Enable
in imx6q-pcie so MSI from downstream components works even if nobody uses
MSI for the Root Port events.
Fixes: f3fdfc4ac3a2 ("PCI: Remove host driver Kconfig selection of CONFIG_PCIEPORTBUS")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Tested-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4a7dca5de625018b29417ecc39dc5037d9a5a36 ]
In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call
event_ctl() several times with the same "ctl" struct. Each call clobbers
ctl.flags, which leads to the problem that we may not actually enable or
disable all events as the user requested.
Preserve the event flag value with a temporary variable.
Fixes: 52eabba5bcdb ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3f7bb2ec20ce07c02b2002349d256c91a463fcc5 upstream.
The write to the status register is really an ACK for the HW,
and should be treated as such by the driver. Let's move it to the
irq_ack() callback, which will prevent people from moving it around
in order to paper over other bugs.
Fixes: 8c934095fa2f ("PCI: dwc: Clear MSI interrupt status after it is handled,
not before")
Fixes: 7c5925afbc58 ("PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API")
Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/
Reported-by: Trent Piepho <tpiepho@impinj.com>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fce5423e4f431c71933d6c1f850b540a314aa6ee upstream.
Bizarrely, there is no lock taken in the irq_ack() helper. This
puts the ACK callback provided by a specific platform in a awkward
situation where there is no synchronization that would be expected
on other callback.
Introduce the required lock, giving some level of uniformity among
callbacks.
Fixes: 7c5925afbc58 ("PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API")
Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 830920e065e90db318a0da98bf13a02b641eae7f upstream.
The dwc driver is showing an interesting level of brokeness, as it
insists on using the enable/disable set of registers to mask/unmask
MSIs, meaning that an MSIs being generated while the interrupt is in
that "disabled" state will simply be lost.
Let's move to the mask/unmask set of registers, which offers the
expected semantics.
Fixes: 7c5925afbc58 ("PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API")
Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5eb1190074cfb14c5d9cac692f1912eecf1a5e4 upstream.
a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
nullified the runtime PM suspend/resume callback pointers while keeping the
runtime PM enabled.
This caused the SMBus PCI device to stay in D0 with
/sys/devices/.../power/runtime_status showing "error" when the runtime PM
framework attempted to autosuspend the device. This is due to PCI bus
runtime PM, which checks for driver runtime PM callbacks and returns
-ENOSYS if they are not set.
Since i2c-i801.c doesn't need to do anything device-specific for runtime
PM, Jean Delvare proposed this be fixed in the PCI core rather than adding
dummy runtime PM callback functions in the PCI drivers.
Change pci_pm_runtime_suspend()/pci_pm_runtime_resume() so they allow
changing the PCI device power state during runtime PM transitions even if
the driver supplies no runtime PM callbacks.
This fixes the runtime PM regression on i2c-i801.c.
It is not obvious why the code previously required the runtime PM
callbacks. The test has been there since the code was introduced by
6cbf82148ff2 ("PCI PM: Run-time callbacks for PCI bus type").
On the other hand, a similar change was done to generic runtime PM
callbacks in 05aa55dddb9e ("PM / Runtime: Lenient generic runtime pm
callbacks").
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 68bc10bf992180f269816ff3d22eb30383138577 ]
This bug was introduced in the interaction for two commits on either
branch of the merge commit 562df5c8521e ("Merge branch
'pci/host-designware' into next").
Commit 4d107d3b5a68 ("PCI: imx6: Move link up check into
imx6_pcie_wait_for_link()"), changed imx6_pcie_wait_for_link() to poll
the link status register directly, checking for link up and not
training, and made imx6_pcie_link_up() only check the link up bit (once,
not a polling loop).
While commit 886bc5ceb5cc ("PCI: designware: Add generic
dw_pcie_wait_for_link()"), replaced the loop in
imx6_pcie_wait_for_link() with a call to a new dwc core function, which
polled imx6_pcie_link_up(), which still checked both link up and not
training in a loop.
When these two commits were merged, the version of
imx6_pcie_wait_for_link() from 886bc5ceb5cc was kept, which eliminated
the link training check placed there by 4d107d3b5a68. However, the
version of imx6_pcie_link_up() from 4d107d3b5a68 was kept, which
eliminated the link training check that had been there and was moved to
imx6_pcie_wait_for_link().
The result was the link training check got lost for the imx6 driver.
Eliminate imx6_pcie_link_up() so that the default handler,
dw_pcie_link_up(), is used instead. The default handler has the correct
code, which checks for link up and also that it still is not training,
fixing the regression.
Fixes: 562df5c8521e ("Merge branch 'pci/host-designware' into next")
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f1f90e254e46e0a14220e4090041f68256fbe297 upstream.
The macros PCI_EXP_LNKCAP_SLS_*GB are values, not bit masks. We must mask
the register and compare it against them.
This fixes errors like this:
amdgpu: [powerplay] failed to send message 261 ret is 0
when a PCIe-v3 card is plugged into a PCIe-v1 slot, because the slot is
being incorrectly reported as PCIe-v3 capable.
6cf57be0f78e, which appeared in v4.17, added pcie_get_speed_cap() with the
incorrect test of PCI_EXP_LNKCAP_SLS as a bitmask. 5d9a63304032, which
appeared in v4.19, changed amdgpu to use pcie_get_speed_cap(), so the
amdgpu bug reports below are regressions in v4.19.
Fixes: 6cf57be0f78e ("PCI: Add pcie_get_speed_cap() to find max supported link speed")
Fixes: 5d9a63304032 ("drm/amdgpu: use pcie functions for link width and speed")
Link: https://bugs.freedesktop.org/show_bug.cgi?id=108704
Link: https://bugs.freedesktop.org/show_bug.cgi?id=108778
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
[bhelgaas: update comment, remove use of PCI_EXP_LNKCAP_SLS_8_0GB and
PCI_EXP_LNKCAP_SLS_16_0GB since those should be covered by PCI_EXP_LNKCAP2,
remove test of PCI_EXP_LNKCAP for zero, since that register is required]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15cb127e3c8f6232096d5dba6a5b4046bc292d70 upstream.
Fix an error caused by 3-bit right rotation on offset address
calculation of MSI-X table in dw_pcie_ep_raise_msix_irq().
The initial testing code was setting by default the offset address of
MSI-X table to zero, so that even with a 3-bit right rotation the
computed result would still be zero and valid, therefore this bug went
unnoticed.
Fixes: beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6fd6fe9dea44732cdcd970f1130b8cc50ad685a upstream.
The order of parameters is not correct when invoking the outbound
window disable routine. Fix it.
Fixes: 4a2745d760fa ("PCI: layerscape: Disable outbound windows configured by bootloader")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0c9606b31a21028fb5b753c8ad79626292accfd upstream.
Add Device IDs to the Intel GPU "spurious interrupt" quirk table.
For these devices, unplugging the VGA cable and plugging it in again causes
spurious interrupts from the IGD. Linux eventually disables the interrupt,
but of course that disables any other devices sharing the interrupt.
The theory is that this is a VGA BIOS defect: it should have disabled the
IGD interrupt but failed to do so.
See f67fd55fa96f ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") and 7c82126a94e6 ("PCI: Add new ID for Intel GPU
"spurious interrupt" quirk") for some history.
[bhelgaas: See link below for discussion about how to fix this more
generically instead of adding device IDs for every new Intel GPU. I hope
this is the last patch to add device IDs.]
Link: https://lore.kernel.org/linux-pci/1537974841-29928-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aeae4f3e5c38d47bdaef50446dc0ec857307df68 upstream.
Upon removal of the last device on a bus, the link_state of the bridge
leading to that bus is sought to be torn down by having pci_stop_dev()
call pcie_aspm_exit_link_state().
When ASPM was originally introduced by commit 7d715a6c1ae5 ("PCI: add
PCI Express ASPM support"), it determined whether the device being
removed is the last one by calling list_empty() on the bridge's
subordinate devices list. That didn't work because the device is only
removed from the list slightly later in pci_destroy_dev().
Commit 3419c75e15f8 ("PCI: properly clean up ASPM link state on device
remove") attempted to fix it by calling list_is_last(), but that's not
correct either because it checks whether the device is at the *end* of
the list, not whether it's the last one *left* in the list. If the user
removes the device which happens to be at the end of the list via sysfs
but other devices are preceding the device in the list, the link_state
is torn down prematurely.
The real fix is to move the invocation of pcie_aspm_exit_link_state() to
pci_destroy_dev() and reinstate the call to list_empty(). Remove a
duplicate check for dev->bus->self because pcie_aspm_exit_link_state()
already contains an identical check.
Fixes: 7d715a6c1ae5 ("PCI: add PCI Express ASPM support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: stable@vger.kernel.org # v2.6.26
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 726d75a6d243bf6730da3216f3592503f6f0f588 ]
Errata i870 is applicable in both EP and RC mode. Therefore rename
function dra7xx_pcie_ep_unaligned_memaccess(), that implements errata
workaround, to dra7xx_pcie_unaligned_memaccess() and call it for both RC
and EP. Make sure driver probe does not fail in case the workaround is not
applied for RC mode in order to maintain DT backward compatibility.
Reported-by: Chris Welch <Chris.Welch@viavisolutions.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[lorenzo.pieralisi@arm.com: reworded the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4c1ef72e9b71a19fb405ebfcd37c0a5e16fa44ca ]
It is a serious driver defect to enable MSI or MSI-X more than once. Doing
so may panic the kernel as in the stack trace below:
Call Trace:
sysfs_add_one+0xa5/0xd0
create_dir+0x7c/0xe0
sysfs_create_subdir+0x1c/0x20
internal_create_group+0x6d/0x290
sysfs_create_groups+0x4a/0xa0
populate_msi_sysfs+0x1cd/0x210
pci_enable_msix+0x31c/0x3e0
igbuio_pci_open+0x72/0x300 [igb_uio]
uio_open+0xcc/0x120 [uio]
chrdev_open+0xa1/0x1e0
[...]
do_sys_open+0xf3/0x1f0
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
---[ end trace 11042e2848880209 ]---
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa056b4fa
We want to keep the WARN_ON() and stack trace so the driver can be fixed,
but we can avoid the kernel panic by returning an error. We may still get
warnings like this:
Call Trace:
pci_enable_msix+0x3c9/0x3e0
igbuio_pci_open+0x72/0x300 [igb_uio]
uio_open+0xcc/0x120 [uio]
chrdev_open+0xa1/0x1e0
[...]
do_sys_open+0xf3/0x1f0
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:526 sysfs_add_one+0xa5/0xd0()
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:03.0/0000:01:00.1/msi_irqs'
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
[bhelgaas: changelog, fix patch whitespace, remove !!]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aa77e55d48124d0d78456eabf872fffb5decdbe1 ]
Test the correct value to see whether the PHY get failed.
Use devm_phy_get() instead of devm_phy_optional_get(), since it is
only called if phy name is given in devicetree and so should exist.
If failure when getting or linking PHY, put any PHYs which were
already got and unlink them.
Fixes: dfb80534692ddc5b ("PCI: cadence: Add generic PHY support to host and EP drivers")
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6299cf9ec3985cac70bede8a855b5087b81a6640 ]
We enable power management automatically for bridges where
pci_bridge_d3_possible() returns true. However, these bridges may have
ACPI methods such as _DSW that need to be called before D3 entry. For
example in Lenovo Thinkpad X1 Carbon 6th _DSW method is used to prepare
D3cold for the PCIe root port hosting Thunderbolt chain. Because wake is
not enabled _DSW method is never called and the port does not enter
D3cold properly consuming more power than necessary.
Users can work this around by writing "enabled" to "wakeup" sysfs file
under the device in question but that is not something an ordinary user
is expected to do.
Since we already automatically enable power management for PCIe ports
with ->bridge_d3 set extend that to enable wake for them as well,
assuming the port has any ACPI wakeup related objects implemented in the
namespace (adev->wakeup.flags.valid is true). This ensures the necessary
ACPI methods get called at appropriate times and allows the root port in
Thinkpad X1 Carbon 6th to go into D3cold.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0652d4b6b56f73c81abbdbc7e26f772cb2dfe370 ]
The IRQ physical address is allocated from region 0, rather than
the highest region. Update the driver to reserve this region in
the bitmap and to use region 0 for all types of interrupt.
This corrects a problem which prevents the interrupt being
signalled correctly if using the first address in the AXI region,
since an offset of zero will always be mapped to region 0.
Fixes: 37dddf14f1ae ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 074d6f32689ce05a084b6fa3db38445745bf11cc ]
The Mediatek's host controller has two slots, each with its own control
registers. The host driver needs to identify what slot is connected to
what port in order to access the device's configuration space.
Current code retrieving slot connected to a given endpoint device.
Assuming each slot is connected to one endpoint device as below:
host bridge
bus 0 --> __________|_______
| |
| |
slot 0 slot 1
bus 1 -->| bus 2 --> |
| |
EP 0 EP 1
During PCI enumeration, system software will scan all the PCI devices on
every bus starting from devfn 0. Using PCI_SLOT(devfn) for matching an
endpoint to its slot is erroneous in that the devfn does not contain the
hierarchical bus numbering in it. In order to match an endpoint with its
slot (and related port), the PCI tree must be walked up to the root bus
(where the root ports are situated) and then the PCI_SLOT(devfn)
matching logic can be correctly applied for matching.
This patch fixes the mtk_pcie_find_port() slot matching logic by adding
appropriate PCI tree walking code to retrieve the slot/port a given
endpoint is connected to.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Kees writes:
"Fix open-coded multiplication arguments to allocators
- Fixes several new open-coded multiplications added in the 4.19
merge window."
* tag 'alloc-args-v4.19-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Replace more open-coded allocation size multiplications
|
|
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Bjorn writes:
"PCI fixes for v4.19:
- Reprogram bridge prefetch registers to fix NVIDIA and Radeon issues
after suspend/resume (Daniel Drake)
- Fix mvebu I/O mapping creation sequence (Thomas Petazzoni)
- Fix minor MAINTAINERS file match issue (Bjorn Helgaas)"
* tag 'pci-v4.19-fixes-3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: mvebu: Fix PCI I/O mapping creation sequence
MAINTAINERS: Remove obsolete drivers/pci pattern from ACPI section
PCI: Reprogram bridge prefetch registers on resume
|
|
Commit ee1604381a371 ("PCI: mvebu: Only remap I/O space if configured") had
the side effect that the PCI I/O mapping was created much earlier than
before, at a point where the probe() of the driver could still fail. This
is for example a problem if one gets an -EPROBE_DEFER at some point during
probe(), after pci_ioremap_io() has been called.
Indeed, there is currently no function to undo what pci_ioremap_io() did,
and switching to pci_remap_iospace() is not an option in pci-mvebu due to
the need for special memory attributes on Armada 38x.
Reverting ee1604381a371 ("PCI: mvebu: Only remap I/O space if configured")
would be a possibility, but it would require also reverting 42342073e38b5
("PCI: mvebu: Convert to use pci_host_bridge directly"). So instead, we use
an open-coded version of pci_host_probe() that creates the PCI I/O mapping
at a point where we are guaranteed not to fail anymore.
Fixes: ee1604381a371 ("PCI: mvebu: Only remap I/O space if configured")
Reported-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Bjorn writes:
"PCI fixes:
- Fix ACPI hotplug issue that causes black screen crash at boot (Mika
Westerberg)
- Fix DesignWare "scheduling while atomic" issues (Jisheng Zhang)
- Add PPC contacts to MAINTAINERS for PCI core error handling (Bjorn
Helgaas)
- Sort Mobiveil MAINTAINERS entry (Lorenzo Pieralisi)"
* tag 'pci-v4.19-fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
PCI: dwc: Fix scheduling while atomic issues
MAINTAINERS: Move mobiveil PCI driver entry where it belongs
MAINTAINERS: Update PPC contacts for PCI core error handling
|
|
On 38+ Intel-based ASUS products, the NVIDIA GPU becomes unusable after S3
suspend/resume. The affected products include multiple generations of
NVIDIA GPUs and Intel SoCs. After resume, nouveau logs many errors such
as:
fifo: fault 00 [READ] at 0000005555555000 engine 00 [GR] client 04
[HUB/FE] reason 4a [] on channel -1 [007fa91000 unknown]
DRM: failed to idle channel 0 [DRM]
Similarly, the NVIDIA proprietary driver also fails after resume (black
screen, 100% CPU usage in Xorg process). We shipped a sample to NVIDIA for
diagnosis, and their response indicated that it's a problem with the parent
PCI bridge (on the Intel SoC), not the GPU.
Runtime suspend/resume works fine, only S3 suspend is affected.
We found a workaround: on resume, rewrite the Intel PCI bridge
'Prefetchable Base Upper 32 Bits' register (PCI_PREF_BASE_UPPER32). In the
cases that I checked, this register has value 0 and we just have to rewrite
that value.
Linux already saves and restores PCI config space during suspend/resume,
but this register was being skipped because upon resume, it already has
value 0 (the correct, pre-suspend value).
Intel appear to have previously acknowledged this behaviour and the
requirement to rewrite this register:
https://bugzilla.kernel.org/show_bug.cgi?id=116851#c23
Based on that, rewrite the prefetch register values even when that appears
unnecessary.
We have confirmed this solution on all the affected models we have in-hands
(X542UQ, UX533FD, X530UN, V272UN).
Additionally, this solves an issue where r8169 MSI-X interrupts were broken
after S3 suspend/resume on ASUS X441UAR. This issue was recently worked
around in commit 7bb05b85bc2d ("r8169: don't use MSI-X on RTL8106e"). It
also fixes the same issue on RTL6186evl/8111evl on an Aimfor-tech laptop
that we had not yet patched. I suspect it will also fix the issue that was
worked around in commit 7c53a722459c ("r8169: don't use MSI-X on
RTL8168g").
Thomas Martitz reports that this change also solves an issue where the AMD
Radeon Polaris 10 GPU on the HP Zbook 14u G5 is unresponsive after S3
suspend/resume.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201069
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-By: Peter Wu <peter@lekensteyn.nl>
CC: stable@vger.kernel.org
|
|
HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports. The root ports themselves are native PCIe hotplug capable. Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:
ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()
It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug. This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens. Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().
In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).
Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127
Fixes: 84c8b58ed3ad ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Reported-by: Peter Anemone <peter.anemone@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.18+
|
|
In case of error, the function pci_create_slot() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When programming the inbound/outbound ATUs, we call usleep_range() after
each checking PCIE_ATU_ENABLE bit. Unfortunately, the ATU programming
can be executed in atomic context:
inbound ATU programming could be called through
pci_epc_write_header()
=>dw_pcie_ep_write_header()
=>dw_pcie_prog_inbound_atu()
outbound ATU programming could be called through
pci_bus_read_config_dword()
=>dw_pcie_rd_conf()
=>dw_pcie_prog_outbound_atu()
Fix this issue by calling mdelay() instead.
Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
Dave writes:
"Various fixes, all over the place:
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
|
|
The Hyper-V host API for PCI provides a unique "serial number" which
can be used as basis for sysfs PCI slot table. This can be useful
for cases where userspace wants to find the PCI device based on
serial number.
When an SR-IOV NIC is added, the host sends an attach message
with serial number. The kernel doesn't use the serial number, but
it is useful when doing the same thing in a userspace driver such
as the DPDK. By having /sys/bus/pci/slots/N it provides a direct
way to find the matching PCI device.
There maybe some cases where serial number is not unique such
as when using GPU's. But the PCI slot infrastructure will handle
that.
This has a side effect which may also be useful. The common udev
network device naming policy uses the slot information (rather
than PCI address).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the eetlp_prefix_path on PCIE_EXP_TYPE_RC_END devices to allow PASID
to be enabled on them. This fixes IOMMUv2 initialization on AMD Carrizo
APUs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201079
Fixes: 7ce3f912ae ("PCI: Enable PASID only if entire path supports End-End TLP prefixes")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Calling into the new API to reset the secondary bus results in a deadlock.
This occurs because the device/bus is already locked at probe time.
Reverting back to the old behavior while the API is improved.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200985
Fixes: c6a44ba950d1 ("PCI: Rename pci_try_reset_bus() to pci_reset_bus()")
Fixes: 409888e0966e ("IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset")
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Cc: Sinan Kaya <okaya@codeaurora.org>
|
Stefan Mätje
Kazufumi Ikeda
Jisheng Zhang
Jean-Philippe Brucker
James Prestwood
Nikolai Kostrigin
Dexuan Cui
Peter Zijlstra
Mika Westerberg
Sergey Miroshnichenko
Andre Przywara
Rafael J. Wysocki
Lucas Stach
Dongdong Liu
Bjorn Helgaas
Logan Gunthorpe
Richard Zhu
Joey Zhang
Marc Zyngier
Jarkko Nikula
Trent Piepho
Mikulas Patocka
Gustavo Pimentel
Hou Zhiqiang
Bin Meng
Lukas Wunner
Vignesh R
Tonghao Zhang
Alan Douglas
Honghui Zhang
Greg Kroah-Hartman
Kees Cook
Thomas Petazzoni
Daniel Drake
Wei Yongjun
Stephen Hemminger
Felix Kuehling
Dennis Dalessandro