| Age | Commit message (Collapse) | Author |
|---|
|
Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-05-22
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.13
('net/mlx5: Add command entry handling completion')
For -stable v5.2
('net/mlx5: Fix error flow in case of function_setup failure')
('net/mlx5: Fix memory leak in mlx5_events_init')
For -stable v5.3
('net/mlx5e: Update netdev txq on completions during closure')
('net/mlx5e: kTLS, Destroy key object after destroying the TIS')
('net/mlx5e: Fix inner tirs handling')
For -stable v5.6
('net/mlx5: Fix cleaning unmanaged flow tables')
('net/mlx5: Fix a race when moving command interface to events mode')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.
Fixes: fe6f700d6cbb ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
cpsw_suspend()
|- cpsw_ndo_stop()
|- __hw_addr_ref_unsync_dev()
|- cpsw_purge_all_mc()
|- vlan_for_each()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.
Fixes: 1bbe0ecc2a1a ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 14b41a2959fb ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.
Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized. Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce(). timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().
systemd--1995 2.... 552950018us : stmmac_suspend: 4994
ksoftirq-9 0..s2 553123133us : stmmac_tx_timer_arm: 2276
systemd--1995 0.... 553127896us : stmmac_resume: 5101
systemd--320 7...2 553132752us : stmmac_tx_timer_arm: 2276
(sd-exec-1999 5...2 553135204us : stmmac_tx_timer_arm: 2276
---------------------------------
pc : run_timer_softirq+0x468/0x5e0
lr : run_timer_softirq+0x570/0x5e0
Call trace:
run_timer_softirq+0x468/0x5e0
__do_softirq+0x124/0x398
irq_exit+0xd8/0xe0
__handle_domain_irq+0x6c/0xc0
gic_handle_irq+0x60/0xb0
el1_irq+0xb8/0x180
arch_cpu_idle+0x38/0x230
default_idle_call+0x24/0x3c
do_idle+0x1e0/0x2b8
cpu_startup_entry+0x28/0x48
secondary_start_kernel+0x1b4/0x208
Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if an error occurred during mlx5_function_setup(), we
keep dev->state as DEVICE_STATE_UP.
Fixing it by adding a goto label.
Fixes: e161105e58da ("net/mlx5: Function setup/teardown procedures")
Signed-off-by: Shay Drory <shayd@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The correct way is to us the flow_cls_offload_flow_rule() wrapper
instead of f->rule directly.
Fixes: 4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On sq closure when we free its descriptors, we should also update netdev
txq on completions which would not arrive. Otherwise if we reopen sqs
and attach them back, for example on fw fatal recovery flow, we may get
tx timeout.
Fixes: 29429f3300a3 ("net/mlx5e: Timeout if SQ doesn't flush during close")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Invoke mutex_destroy() to catch any errors.
Fixes: 2cc43b494a6c ("net/mlx5_core: Managing root flow table")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add del_sw_func cb for root ns. Now there is no need to
maintain a case of del_sw_func being null when freeing the node.
Fixes: 2cc43b494a6c ("net/mlx5_core: Managing root flow table")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Unmanaged flow tables doesn't have a parent and tree_put_node()
assume there is always a parent if cleaning is needed. fix that.
Fixes: 5281a0c90919 ("net/mlx5: fs_core: Introduce unmanaged flow tables")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix memory leak in mlx5_events_init(), in case
create_single_thread_workqueue() fails, events
struct should be freed.
Fixes: 5d3c537f9070 ("net/mlx5: Handle event of power detection in the PCIE slot")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the cited commit inner_tirs argument was added to create and destroy
inner tirs, and no indication was added to mlx5e_modify_tirs_hash()
function. In order to have a consistent handling, use
inner_indir_tir[0].tirn in tirs destroy/modify function as an indication
to whether inner tirs are created.
Inner tirs are not created for representors and before this commit,
a call to mlx5e_modify_tirs_hash() was sending HW commands to
modify non-existent inner tirs.
Fixes: 46dc933cee82 ("net/mlx5e: Provide explicit directive if to create inner indirect tirs")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The TLS TIS object contains the dek/key ID.
By destroying the key first, the TIS would contain an invalid
non-existing key ID.
Reverse the destroy order, this also acheives the desired assymetry
between the destroy and the create flows.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After changing the parent_id to be the same for both NICs of same
The cited commit wrongly allow offload of tc redirect flows from
VF to uplink and vice versa when devcies are on different eswitch,
these cases aren't supported by HW.
Disallow the above offloads when devcies are on different eswitch
and VF LAG is not configured.
Fixes: f6dc1264f1c0 ("net/mlx5e: Disallow tc redirect offload cases we don't support")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver is reloading during recovery flow, it can't get new commands
till command interface is up again. Otherwise we may get to null pointer
trying to access non initialized command structures.
Add cmdif state to avoid processing commands while cmdif is not ready.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After driver creates (via FW command) an EQ for commands, the driver will
be informed on new commands completion by EQE. However, due to a race in
driver's internal command mode metadata update, some new commands will
still be miss-handled by driver as if we are in polling mode. Such commands
can get two non forced completion, leading to already freed command entry
access.
CREATE_EQ command, that maps EQ to the command queue must be posted to the
command queue while it is empty and no other command should be posted.
Add SW mechanism that once the CREATE_EQ command is about to be executed,
all other commands will return error without being sent to the FW. Allow
sending other commands only after successfully changing the driver's
internal command mode metadata.
We can safely return error to all other commands while creating the command
EQ, as all other commands might be sent from the user/application during
driver load. Application can rerun them later after driver's load was
finished.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When FW response to commands is very slow and all command entries in
use are waiting for completion we can have a race where commands can get
timeout before they get out of the queue and handled. Timeout
completion on uninitialized command will cause releasing command's
buffers before accessing it for initialization and then we will get NULL
pointer exception while trying access it. It may also cause releasing
buffers of another command since we may have timeout completion before
even allocating entry index for this command.
Add entry handling completion to avoid this race.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In cas_init_one(), "pdev" is requested by "pci_request_regions", but it
was not released after a call of the function “pci_write_config_byte”
failed. Thus replace the jump target “err_write_cacheline” by
"err_out_free_res".
Fixes: 1f26dac32057 ("[NET]: Add Sun Cassini driver.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_set_ageing_time has 2 callers:
- felix_set_ageing_time: from drivers/net/dsa/ocelot/felix.c
- ocelot_port_attr_ageing_set: from drivers/net/ethernet/mscc/ocelot.c
The issue described in the fixed commit below actually happened for the
felix_set_ageing_time code path only, since ocelot_port_attr_ageing_set
was already dividing by 1000. So to make both paths symmetrical (and to
fix addresses getting aged way too fast on Ocelot), stop dividing by
1000 at caller side altogether.
Fixes: c0d7eccbc761 ("net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa139 ("r8169: add support for RTL8117")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fails
In case of reload fail, the mlxsw_sp->ports contains a pointer to a
freed memory (either by reload_down() or reload_up() error path).
Fix this by initializing the pointer to NULL and checking it before
dereferencing in split/unsplit/type_set callpaths.
Fixes: 24cc68ad6c46 ("mlxsw: core: Add support for reload")
Reported-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the policer drop counter is retrieved when the jiffies value is
a multiple of 64, the counter will not be incremented.
This randomly breaks a selftest [1] the reads the counter twice and
checks that it was incremented:
```
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
```
Fix by always incrementing the counter by 1.
[1] tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh
Fixes: ad188458d012 ("netdevsim: Add devlink-trap policer support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without 895586d5dc32 and with 895586d5dc32 applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with 895586d5dc32, failing: 00200000 40000000
- without 895586d5dc32, working: 04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc32, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function devm_platform_ioremap_resource(), if get resource
failed, the return value is ERR_PTR() not NULL. Thus it must be
replaced by IS_ERR(), or else it may result in crashes if a critical
error path is encountered.
Fixes: 0ce5ebd24d25 ("mfd: ioc3: Add driver for SGI IOC3 chip")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert to using IS_ERR() instead of NULL test for cpsw_ale_create()
error handling. Also fix to return negative error code from this error
handling case instead of 0 in.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpsw_ale_create() can return both NULL and PTR_ERR(), but all of
the caller only check NULL for error handling. This patch convert
it to only return PTR_ERR() in all error cases, and the caller using
IS_ERR() instead of NULL test.
Fixes: 4b41d3436796 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In "wireguard: queueing: preserve flow hash across packet scrubbing", we
were required to slightly increase the size of the receive replay
counter to something still fairly small, but an increase nonetheless.
It turns out that we can recoup some of the additional memory overhead
by splitting up the prior union type into two distinct types. Before, we
used the same "noise_counter" union for both sending and receiving, with
sending just using a simple atomic64_t, while receiving used the full
replay counter checker. This meant that most of the memory being
allocated for the sending counter was being wasted. Since the old
"noise_counter" type increased in size in the prior commit, now is a
good time to split up that union type into a distinct "noise_replay_
counter" for receiving and a boring atomic64_t for sending, each using
neither more nor less memory than required.
Also, since sometimes the replay counter is accessed without
necessitating additional accesses to the bitmap, we can reduce cache
misses by hoisting the always-necessary lock above the bitmap in the
struct layout. We also change a "noise_replay_counter" stack allocation
to kmalloc in a -DDEBUG selftest so that KASAN doesn't trigger a stack
frame warning.
All and all, removing a bit of abstraction in this commit makes the code
simpler and smaller, in addition to the motivating memory usage
recuperation. For example, passing around raw "noise_symmetric_key"
structs is something that really only makes sense within noise.c, in the
one place where the sending and receiving keys can safely be thought of
as the same type of object; subsequent to that, it's important that we
uniformly access these through keypair->{sending,receiving}, where their
distinct roles are always made explicit. So this patch allows us to draw
that distinction clearly as well.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's important that we clear most header fields during encapsulation and
decapsulation, because the packet is substantially changed, and we don't
want any info leak or logic bug due to an accidental correlation. But,
for encapsulation, it's wrong to clear skb->hash, since it's used by
fq_codel and flow dissection in general. Without it, classification does
not proceed as usual. This change might make it easier to estimate the
number of innerflows by examining clustering of out of order packets,
but this shouldn't open up anything that can't already be inferred
otherwise (e.g. syn packet size inference), and fq_codel can be disabled
anyway.
Furthermore, it might be the case that the hash isn't used or queried at
all until after wireguard transmits the encrypted UDP packet, which
means skb->hash might still be zero at this point, and thus no hash
taken over the inner packet data. In order to address this situation, we
force a calculation of skb->hash before encrypting packet data.
Of course this means that fq_codel might transmit packets slightly more
out of order than usual. Toke did some testing on beefy machines with
high quantities of parallel flows and found that increasing the
reply-attack counter to 8192 takes care of the most pathological cases
pretty well.
Reported-by: Dave Taht <dave.taht@gmail.com>
Reviewed-and-tested-by: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior we read the preshared key after dropping the handshake lock, which
isn't an actual crypto issue if it races, but it's still not quite
correct. So copy that part of the state into a temporary like we do with
the rest of the handshake state variables. Then we can release the lock,
operate on the temporary, and zero it out at the end of the function. In
performance tests, the impact of this was entirely unnoticable, probably
because those bytes are coming from the same cacheline as other things
that are being copied out in the same manner.
Reported-by: Matt Dunwoodie <ncon@noconroy.net>
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <marc.payne@mdpsys.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.7
Third and most likely the last set of fixes for v5.7. Only one
iwlwifi fix this time.
iwlwifi
* another fix for QuZ device configuration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bmac_get_station_address, We're reading two bytes at a time from ROM,
but we do that six times, resulting in 12 bytes of read & writes. This
means we will write off the end of the six-byte destination buffer.
This change fixes the for-loop to only read/write six bytes.
Based on a proposed fix from Finn Thain <fthain@telegraphics.com.au>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The compilation warning below reveals that the errors returned from
the sfp_bus_add_upstream() call are not propagated to the callers.
Fix it by returning "ret".
14:37:51 drivers/net/phy/phy_device.c: In function 'phy_sfp_probe':
14:37:51 drivers/net/phy/phy_device.c:1236:6: warning: variable 'ret'
set but not used [-Wunused-but-set-variable]
14:37:51 1236 | int ret;
14:37:51 | ^~~
Fixes: 298e54fa810e ("net: phy: add core phylib sfp support")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The iteration count value used in gsi_channel_poll() is intended to
limit poll iterations to the budget supplied as an argument. But
it's never updated.
Fix this bug by incrementing the count each time through the loop.
Reported-by: Sharath Chandra Vurukala <sharathv@codeaurora.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on the WRIOP version, the buffer size on the RX path must by a
multiple of 64 or 256. Handle this restriction properly by aligning down
the buffer size to the necessary value. Also, use the new buffer size
dynamically computed instead of the compile time one.
Fixes: 27c874867c4e ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc5-next-20200514-syzkaller #0 Not tainted
-----------------------------
drivers/net/hamradio/bpqether.c:149 RCU-list traversed in non-reader section!!
Since rtnl lock is held, pass this cond in list_for_each_entry_rcu().
Reported-by: syzbot+bb82cafc737c002d11ca@syzkaller.appspotmail.com
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the correct bit when checking for PHY_BRCM_DIS_TXCRXC_NOENRGY on the
BCM54810 PHY.
Fixes: 0ececcfc9267 ("net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk()")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the duplicate "mutex", and change "Motex" to "Mutex". Also I
recommend it's easier for understanding to make the "ready-interrupt"
a bundle for it is a parallel description as "shutdown" which is appended
after the slash.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Cc: Alex Elder <elder@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't want to disconnect a session because of a stray PADT arriving
while the interface is in promiscuous mode.
Furthermore, multicast and broadcast packets make no sense here, so
only PACKET_HOST is accepted.
Reported-by: David Balažic <xerces9@gmail.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver missed initializing num_por which is one of the por values that
driver configures to hardware. In order to get these values, add a new
structure ethqos_emac_driver_data which holds por and num_por values
and populate that in driver probe.
Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos")
Reported-by: Rahul Ankushrao Kawadgave <rahulak@qti.qualcomm.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.
Fixes: f75abeb8338e ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET controller on the Raspberry Pi 4 (2711) is typically
interfaced with an external Broadcom PHY via a RGMII electrical
interface. To make sure that delays are properly configured at the PHY
side, ensure that we the dedicated Broadcom PHY driver
(CONFIG_BROADCOM_PHY) is enabled for this to happen.
Fixes: 402482a6a78e ("net: bcmgenet: Clear ID_MODE_DIS in EXT_RGMII_OOB_CTRL when not needed")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My recent commit b6d49cab44b5 ("net: Make PTP-specific drivers depend on
PTP_1588_CLOCK") exposes a missing dependency in defconfigs that select
TI_CPTS without selecting PTP_1588_CLOCK, leading to linker errors of the
form:
drivers/net/ethernet/ti/cpsw.o: in function `cpsw_ndo_stop':
cpsw.c:(.text+0x680): undefined reference to `cpts_unregister'
...
That's because TI_CPTS_MOD (which is the symbol gating the _compilation_ of
cpts.c) now depends on PTP_1588_CLOCK, and so is not enabled in these
configurations, but TI_CPTS (which is the symbol gating _calls_ to the cpts
functions) _is_ enabled. So we end up compiling calls to functions that
don't exist, resulting in the linker errors.
This patch fixes build errors and restores previous behavior by:
- ensure PTP_1588_CLOCK=y in TI specific configs and CPTS will be built
- remove TI_CPTS_MOD and, instead, add dependencies from CPTS in
TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV as below:
config TI_CPSW_SWITCHDEV
...
depends on TI_CPTS || !TI_CPTS
which will ensure proper dependencies PTP_1588_CLOCK -> TI_CPTS ->
TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV and build type selection.
Note. For NFS boot + CPTS all of above configs have to be built-in.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Fixes: b6d49cab44b5 ("net: Make PTP-specific drivers depend on PTP_1588_CLOCK")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Clay McClure <clay@daemons.net>
[grygorii.strashko@ti.com: rewording, add deps cpsw/netcp from cpts, drop IS_REACHABLE]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Dinghao Liu
David S. Miller
Qiushi Wu
Grygorii Strashko
Antoine Tenart
Leon Yu
Tiezhu Yang
Shay Drory
Roi Dayan
Moshe Shemesh
Tariq Toukan
Maor Dickman
Eran Ben Elisha
Vladimir Oltean
Heiner Kallweit
Jiri Pirko
Jonathan McDowell
Ido Schimmel
Valentin Longchamp
Russell King
Claudiu Manoil
Tang Bin
Wei Yongjun
Jason A. Donenfeld
Marc Payne
Jeremy Kerr
Leon Romanovsky
Alex Elder
DENG Qingfang
Ioana Ciornei
Madhuparna Bhowmik
Kevin Lo
Wang Wenhu
Guillaume Nault
Vinod Koul
Florian Fainelli
Clay McClure