| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit da29f2d84bd10234df570b7f07cbd0166e738230 ]
When using fixed link we don't need the MDIO bus support.
Reported-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: kernelci.org bot <bot@kernelci.org>
Fixes: d3e014ec7d5e ("net: stmmac: platform: Fix MDIO init for platforms without PHY")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Acked-by: Sriram Dash <Sriram.dash@samsung.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail> # Lamobo R1 (fixed-link + MDIO sub node for roboswitch).
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 52cc73e5404c7ba0cbfc50cb4c265108c84b3d5a ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba80 ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f1239d8aa84dad8fe4b6cc1356f40fc8e842db47 ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c72a0bc0aa19f49160330a65ab77184b5b7d131b ]
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d8dc2c9676e614ef62f54a155b50076888c8a29a ]
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a676 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 96cc4b69581db68efc9749ef32e9cf8e0160c509 ]
Use of eth_hdr() in tx path is error prone.
Many drivers call skb_reset_mac_header() before using it,
but others do not.
Commit 6d1ccff62780 ("net: reset mac header in dev_start_xmit()")
attempted to fix this generically, but commit d346a3fae3ff
("packet: introduce PACKET_QDISC_BYPASS socket option") brought
back the macvlan bug.
Lets add a new helper, so that tx paths no longer have
to call skb_reset_mac_header() only to get a pointer
to skb->data.
Hopefully we will be able to revert 6d1ccff62780
("net: reset mac header in dev_start_xmit()") and save few cycles
in transmit fast path.
BUG: KASAN: use-after-free in __get_unaligned_cpu32 include/linux/unaligned/packed_struct.h:19 [inline]
BUG: KASAN: use-after-free in mc_hash drivers/net/macvlan.c:251 [inline]
BUG: KASAN: use-after-free in macvlan_broadcast+0x547/0x620 drivers/net/macvlan.c:277
Read of size 4 at addr ffff8880a4932401 by task syz-executor947/9579
CPU: 0 PID: 9579 Comm: syz-executor947 Not tainted 5.5.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:639
__asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:145
__get_unaligned_cpu32 include/linux/unaligned/packed_struct.h:19 [inline]
mc_hash drivers/net/macvlan.c:251 [inline]
macvlan_broadcast+0x547/0x620 drivers/net/macvlan.c:277
macvlan_queue_xmit drivers/net/macvlan.c:520 [inline]
macvlan_start_xmit+0x402/0x77f drivers/net/macvlan.c:559
__netdev_start_xmit include/linux/netdevice.h:4447 [inline]
netdev_start_xmit include/linux/netdevice.h:4461 [inline]
dev_direct_xmit+0x419/0x630 net/core/dev.c:4079
packet_direct_xmit+0x1a9/0x250 net/packet/af_packet.c:240
packet_snd net/packet/af_packet.c:2966 [inline]
packet_sendmsg+0x260d/0x6220 net/packet/af_packet.c:2991
sock_sendmsg_nosec net/socket.c:639 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:659
__sys_sendto+0x262/0x380 net/socket.c:1985
__do_sys_sendto net/socket.c:1997 [inline]
__se_sys_sendto net/socket.c:1993 [inline]
__x64_sys_sendto+0xe1/0x1a0 net/socket.c:1993
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x442639
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 5b 10 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffc13549e08 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000442639
RDX: 000000000000000e RSI: 0000000020000080 RDI: 0000000000000003
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000403bb0 R14: 0000000000000000 R15: 0000000000000000
Allocated by task 9389:
save_stack+0x23/0x90 mm/kasan/common.c:72
set_track mm/kasan/common.c:80 [inline]
__kasan_kmalloc mm/kasan/common.c:513 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:486
kasan_kmalloc+0x9/0x10 mm/kasan/common.c:527
__do_kmalloc mm/slab.c:3656 [inline]
__kmalloc+0x163/0x770 mm/slab.c:3665
kmalloc include/linux/slab.h:561 [inline]
tomoyo_realpath_from_path+0xc5/0x660 security/tomoyo/realpath.c:252
tomoyo_get_realpath security/tomoyo/file.c:151 [inline]
tomoyo_path_perm+0x230/0x430 security/tomoyo/file.c:822
tomoyo_inode_getattr+0x1d/0x30 security/tomoyo/tomoyo.c:129
security_inode_getattr+0xf2/0x150 security/security.c:1222
vfs_getattr+0x25/0x70 fs/stat.c:115
vfs_statx_fd+0x71/0xc0 fs/stat.c:145
vfs_fstat include/linux/fs.h:3265 [inline]
__do_sys_newfstat+0x9b/0x120 fs/stat.c:378
__se_sys_newfstat fs/stat.c:375 [inline]
__x64_sys_newfstat+0x54/0x80 fs/stat.c:375
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 9389:
save_stack+0x23/0x90 mm/kasan/common.c:72
set_track mm/kasan/common.c:80 [inline]
kasan_set_free_info mm/kasan/common.c:335 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:474
kasan_slab_free+0xe/0x10 mm/kasan/common.c:483
__cache_free mm/slab.c:3426 [inline]
kfree+0x10a/0x2c0 mm/slab.c:3757
tomoyo_realpath_from_path+0x1a7/0x660 security/tomoyo/realpath.c:289
tomoyo_get_realpath security/tomoyo/file.c:151 [inline]
tomoyo_path_perm+0x230/0x430 security/tomoyo/file.c:822
tomoyo_inode_getattr+0x1d/0x30 security/tomoyo/tomoyo.c:129
security_inode_getattr+0xf2/0x150 security/security.c:1222
vfs_getattr+0x25/0x70 fs/stat.c:115
vfs_statx_fd+0x71/0xc0 fs/stat.c:145
vfs_fstat include/linux/fs.h:3265 [inline]
__do_sys_newfstat+0x9b/0x120 fs/stat.c:378
__se_sys_newfstat fs/stat.c:375 [inline]
__x64_sys_newfstat+0x54/0x80 fs/stat.c:375
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8880a4932000
which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 1025 bytes inside of
4096-byte region [ffff8880a4932000, ffff8880a4933000)
The buggy address belongs to the page:
page:ffffea0002924c80 refcount:1 mapcount:0 mapping:ffff8880aa402000 index:0x0 compound_mapcount: 0
raw: 00fffe0000010200 ffffea0002846208 ffffea00028f3888 ffff8880aa402000
raw: 0000000000000000 ffff8880a4932000 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880a4932300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880a4932380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880a4932400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880a4932480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880a4932500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: b863ceb7ddce ("[NET]: Add macvlan driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 90d72256addff9e5f8ad645e8f632750dd1f8935 ]
WARNING: bad unlock balance detected!
5.5.0-rc5-syzkaller #0 Not tainted
-------------------------------------
syz-executor921/9688 is trying to release lock (sk_lock-AF_INET6) at:
[<ffffffff84bf8506>] gtp_encap_enable_socket+0x146/0x400 drivers/net/gtp.c:830
but there are no more locks to release!
other info that might help us debug this:
2 locks held by syz-executor921/9688:
#0: ffffffff8a4d8840 (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:72 [inline]
#0: ffffffff8a4d8840 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x405/0xaf0 net/core/rtnetlink.c:5421
#1: ffff88809304b560 (slock-AF_INET6){+...}, at: spin_lock_bh include/linux/spinlock.h:343 [inline]
#1: ffff88809304b560 (slock-AF_INET6){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2951
stack backtrace:
CPU: 0 PID: 9688 Comm: syz-executor921 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_unlock_imbalance_bug kernel/locking/lockdep.c:4008 [inline]
print_unlock_imbalance_bug.cold+0x114/0x123 kernel/locking/lockdep.c:3984
__lock_release kernel/locking/lockdep.c:4242 [inline]
lock_release+0x5f2/0x960 kernel/locking/lockdep.c:4503
sock_release_ownership include/net/sock.h:1496 [inline]
release_sock+0x17c/0x1c0 net/core/sock.c:2961
gtp_encap_enable_socket+0x146/0x400 drivers/net/gtp.c:830
gtp_encap_enable drivers/net/gtp.c:852 [inline]
gtp_newlink+0x9fc/0xc60 drivers/net/gtp.c:666
__rtnl_newlink+0x109e/0x1790 net/core/rtnetlink.c:3305
rtnl_newlink+0x69/0xa0 net/core/rtnetlink.c:3363
rtnetlink_rcv_msg+0x45e/0xaf0 net/core/rtnetlink.c:5424
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0x58c/0x7d0 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x91c/0xea0 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:639 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:659
____sys_sendmsg+0x753/0x880 net/socket.c:2330
___sys_sendmsg+0x100/0x170 net/socket.c:2384
__sys_sendmsg+0x105/0x1d0 net/socket.c:2417
__do_sys_sendmsg net/socket.c:2426 [inline]
__se_sys_sendmsg net/socket.c:2424 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2424
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x445d49
Code: e8 bc b7 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 2b 12 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f8019074db8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000006dac38 RCX: 0000000000445d49
RDX: 0000000000000000 RSI: 0000000020000180 RDI: 0000000000000003
RBP: 00000000006dac30 R08: 0000000000000004 R09: 0000000000000000
R10: 0000000000000008 R11: 0000000000000246 R12: 00000000006dac3c
R13: 00007ffea687f6bf R14: 00007f80190759c0 R15: 20c49ba5e353f7cf
Fixes: e198987e7dd7 ("gtp: fix suspicious RCU usage")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b0689faa8efc5a3391402d7ae93bd373b7248e51 ]
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c0fdccfd226a1424683d3000d9e08384391210a2 ]
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. ixgbe_down already calls synchronize_rcu after setting __IXGBE_DOWN.
2. After switching the XDP program, call synchronize_rcu to let
ixgbe_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down.
4. Disabling UMEM sets __IXGBE_TX_DISABLED before closing hardware
resources and resetting xsk_umem. Check that bit in ixgbe_xsk_wakeup to
avoid using the XDP ring when it's already destroyed. synchronize_rcu is
called from ixgbe_txrx_ring_disable.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-5-maximmi@mellanox.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b3873a5be757b44d51af542a50a6f2a3b6f95284 ]
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).
2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).
4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9cf88808ad6a0f1e958e00abd9a081295fe6da0c ]
After disabling resources necessary for XSK (the XDP program, channels,
XSK queues), use synchronize_rcu to wait until the XSK wakeup function
finishes, before freeing the resources.
Suspend XSK wakeups during switching channels. If the XDP program is
being removed, synchronize_rcu before closing the old channels to allow
XSK wakeup to complete.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-3-maximmi@mellanox.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4772f26db8d1fb568c4862c538344a1b5fb52081 ]
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be11 ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d558f0294fe92e04af192e221d0d0f6a180ee7b ]
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11d55fd9975f8e46a0e5e19c14899544e81e1e15 ]
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eaf4fac478077d4ed57cbca2c044c4b58a96bd98 ]
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d626c879e238be9585bd59a61eb606c9408178a ]
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08c965430869ed423921bd9058ae59f75207feb6 ]
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 858ce8ca62ea1530f2779d0e3f934b0176e663c3 ]
Display the return code as decimal integer.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 479a0d1376f6d97c60871442911f1394d4446a25 ]
The sge_info debugfs collects offload queue info even when offload
capability is disabled and leads to panic.
[ 144.139871] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 144.139874] CR2: 0000000000000000 CR3: 000000082d456005 CR4: 00000000001606e0
[ 144.139876] Call Trace:
[ 144.139887] sge_queue_start+0x12/0x30 [cxgb4]
[ 144.139897] seq_read+0x1d4/0x3d0
[ 144.139906] full_proxy_read+0x50/0x70
[ 144.139913] vfs_read+0x89/0x140
[ 144.139916] ksys_read+0x55/0xd0
[ 144.139924] do_syscall_64+0x5b/0x1d0
[ 144.139933] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 144.139936] RIP: 0033:0x7f4b01493990
Fix this crash by skipping the offload queue access in sge_qinfo when
offload capability is disabled
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee699f89bdbaa19c399804504241b5c531b48888 ]
Driver doesn't calculate total number of PFs configured on a
given engine correctly which messed up resources in the PFs
loaded on that engine, leading driver to exceed configuration
of resources (like vlan filters etc.) beyond the limit per
engine, which ended up with asserts from the firmware.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7113f796bbbced2470cd6d7379d50d7a7a78bf34 ]
Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1e58252e334dc3f3756f424a157d1b7484464c40 ]
mwifiex_process_tdls_action_frame() without checking
the incoming tdls infomation element's vality before use it,
this may cause multi heap buffer overflows.
Fix them by putting vality check before use it.
IE is TLV struct, but ht_cap and ht_oper aren’t TLV struct.
the origin marvell driver code is wrong:
memcpy(&sta_ptr->tdls_cap.ht_oper, pos,....
memcpy((u8 *)&sta_ptr->tdls_cap.ht_capb, pos,...
Fix the bug by changing pos(the address of IE) to
pos+2 ( the address of IE value ).
Signed-off-by: qize wang <wangqize888888888@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd486e627e67ee9ab66914d36d3127ef057cc010 ]
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
This patch ports 2 patches from ath9k to ath9k_htc.
commit 3c0efb745a172bfe96459e20cbd37b0c945d5f8d "ath9k: discard
undersized packets".
commit df5c4150501ee7e86383be88f6490d970adcf157 "ath9k: correctly
handle short radar pulses".
[ 112.835889] ------------[ cut here ]------------
[ 112.835971] WARNING: CPU: 5 PID: 0 at net/mac80211/rx.c:804 ieee80211_rx_napi+0xaac/0xb40 [mac80211]
[ 112.835973] Modules linked in: ath9k_htc ath9k_common ath9k_hw ath mac80211 cfg80211 libarc4 nouveau snd_hda_codec_hdmi intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_hda_codec video snd_hda_core ttm snd_hwdep drm_kms_helper snd_pcm crct10dif_pclmul snd_seq_midi drm snd_seq_midi_event crc32_pclmul snd_rawmidi ghash_clmulni_intel snd_seq aesni_intel aes_x86_64 crypto_simd cryptd snd_seq_device glue_helper snd_timer sch_fq_codel i2c_algo_bit fb_sys_fops snd input_leds syscopyarea sysfillrect sysimgblt intel_cstate mei_me intel_rapl_perf soundcore mxm_wmi lpc_ich mei kvm_intel kvm mac_hid irqbypass parport_pc ppdev lp parport ip_tables x_tables autofs4 hid_generic usbhid hid raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear e1000e ahci libahci wmi
[ 112.836022] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.3.0-wt #1
[ 112.836023] Hardware name: MouseComputer Co.,Ltd. X99-S01/X99-S01, BIOS 1.0C-W7 04/01/2015
[ 112.836056] RIP: 0010:ieee80211_rx_napi+0xaac/0xb40 [mac80211]
[ 112.836059] Code: 00 00 66 41 89 86 b0 00 00 00 e9 c8 fa ff ff 4c 89 b5 40 ff ff ff 49 89 c6 e9 c9 fa ff ff 48 c7 c7 e0 a2 a5 c0 e8 47 41 b0 e9 <0f> 0b 48 89 df e8 5a 94 2d ea e9 02 f9 ff ff 41 39 c1 44 89 85 60
[ 112.836060] RSP: 0018:ffffaa6180220da8 EFLAGS: 00010286
[ 112.836062] RAX: 0000000000000024 RBX: ffff909a20eeda00 RCX: 0000000000000000
[ 112.836064] RDX: 0000000000000000 RSI: ffff909a2f957448 RDI: ffff909a2f957448
[ 112.836065] RBP: ffffaa6180220e78 R08: 00000000000006e9 R09: 0000000000000004
[ 112.836066] R10: 000000000000000a R11: 0000000000000001 R12: 0000000000000000
[ 112.836068] R13: ffff909a261a47a0 R14: 0000000000000000 R15: 0000000000000004
[ 112.836070] FS: 0000000000000000(0000) GS:ffff909a2f940000(0000) knlGS:0000000000000000
[ 112.836071] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 112.836073] CR2: 00007f4e3ffffa08 CR3: 00000001afc0a006 CR4: 00000000001606e0
[ 112.836074] Call Trace:
[ 112.836076] <IRQ>
[ 112.836083] ? finish_td+0xb3/0xf0
[ 112.836092] ? ath9k_rx_prepare.isra.11+0x22f/0x2a0 [ath9k_htc]
[ 112.836099] ath9k_rx_tasklet+0x10b/0x1d0 [ath9k_htc]
[ 112.836105] tasklet_action_common.isra.22+0x63/0x110
[ 112.836108] tasklet_action+0x22/0x30
[ 112.836115] __do_softirq+0xe4/0x2da
[ 112.836118] irq_exit+0xae/0xb0
[ 112.836121] do_IRQ+0x86/0xe0
[ 112.836125] common_interrupt+0xf/0xf
[ 112.836126] </IRQ>
[ 112.836130] RIP: 0010:cpuidle_enter_state+0xa9/0x440
[ 112.836133] Code: 3d bc 20 38 55 e8 f7 1d 84 ff 49 89 c7 0f 1f 44 00 00 31 ff e8 28 29 84 ff 80 7d d3 00 0f 85 e6 01 00 00 fb 66 0f 1f 44 00 00 <45> 85 ed 0f 89 ff 01 00 00 41 c7 44 24 10 00 00 00 00 48 83 c4 18
[ 112.836134] RSP: 0018:ffffaa61800e3e48 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
[ 112.836136] RAX: ffff909a2f96b340 RBX: ffffffffabb58200 RCX: 000000000000001f
[ 112.836137] RDX: 0000001a458adc5d RSI: 0000000026c9b581 RDI: 0000000000000000
[ 112.836139] RBP: ffffaa61800e3e88 R08: 0000000000000002 R09: 000000000002abc0
[ 112.836140] R10: ffffaa61800e3e18 R11: 000000000000002d R12: ffffca617fb40b00
[ 112.836141] R13: 0000000000000002 R14: ffffffffabb582d8 R15: 0000001a458adc5d
[ 112.836145] ? cpuidle_enter_state+0x98/0x440
[ 112.836149] ? menu_select+0x370/0x600
[ 112.836151] cpuidle_enter+0x2e/0x40
[ 112.836154] call_cpuidle+0x23/0x40
[ 112.836156] do_idle+0x204/0x280
[ 112.836159] cpu_startup_entry+0x1d/0x20
[ 112.836164] start_secondary+0x167/0x1c0
[ 112.836169] secondary_startup_64+0xa4/0xb0
[ 112.836173] ---[ end trace 9f4cd18479cc5ae5 ]---
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e01fddc19d215f6ad397894ec2a851d99bf154e2 ]
rs_datalen is be16 so we need to convert it before printing.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 24dee0c7478d1a1e00abdf5625b7f921467325dc ]
In netpoll the napi handler could be called with budget equal to zero.
Current ENA napi handler doesn't take that into consideration.
The napi handler handles Rx packets in a do-while loop.
Currently, the budget check happens only after decrementing the
budget, therefore the napi handler, in rare cases, could run over
MAX_INT packets.
In addition to that, this moves all budget related variables to int
calculation and stop mixing u32 to avoid ambiguity
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9b2079c046a9d6c9c73a4ec33816678565ee01f3 ]
A mismerge between the following two commits:
c678726305b9 ("net: phylink: ensure consistent phy interface mode")
27755ff88c0e ("net: phylink: Add phylink_mac_link_{up, down} wrapper functions")
resulted in the wrong interface being passed to the mac_link_up()
function. Fix this up.
Fixes: b4b12b0d2f02 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6adc4601c2a1ac87b4ab8ed0cb55db6efd0264e8 ]
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa712d ("bnxt_en: Update interrupt coalescing logic.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6b01b1d9b2d38dc84ac398bfe9f00baff06a31e5 ]
GTP RX packet path lookups pdp context with TID. If duplicate TID pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, TID value should be unique.
GTP TX packet path lookups pdp context with ms_addr. If duplicate ms_addr pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, ms_addr value should be unique.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 94dc550a5062030569d4aa76e10e50c8fc001930 ]
ipv4_pdp_find() is called in TX packet path of GTP.
ipv4_pdp_find() internally uses gtp->tid_hash to lookup pdp context.
In the current code, gtp->tid_hash and gtp->addr_hash are freed by
->dellink(), which is gtp_dellink().
But gtp_dellink() would be called while packets are processing.
So, gtp_dellink() should not free gtp->tid_hash and gtp->addr_hash.
Instead, dev->priv_destructor() would be used because this callback
is called after all packet processing safely.
Test commands:
ip link add veth1 type veth peer name veth2
ip a a 172.0.0.1/24 dev veth1
ip link set veth1 up
ip a a 172.99.0.1/32 dev lo
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 200 100 172.99.0.2 172.0.0.2
ip r a 172.99.0.2/32 dev gtp1
ip link set gtp1 mtu 1500
ip netns add ns2
ip link set veth2 netns ns2
ip netns exec ns2 ip a a 172.0.0.2/24 dev veth2
ip netns exec ns2 ip link set veth2 up
ip netns exec ns2 ip a a 172.99.0.2/32 dev lo
ip netns exec ns2 ip link set lo up
ip netns exec ns2 gtp-link add gtp2 &
ip netns exec ns2 gtp-tunnel add gtp2 v1 100 200 172.99.0.1 172.0.0.1
ip netns exec ns2 ip r a 172.99.0.1/32 dev gtp2
ip netns exec ns2 ip link set gtp2 mtu 1500
hping3 172.99.0.2 -2 --flood &
ip link del gtp1
Splat looks like:
[ 72.568081][ T1195] BUG: KASAN: use-after-free in ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.568916][ T1195] Read of size 8 at addr ffff8880b9a35d28 by task hping3/1195
[ 72.569631][ T1195]
[ 72.569861][ T1195] CPU: 2 PID: 1195 Comm: hping3 Not tainted 5.5.0-rc1 #199
[ 72.570547][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 72.571438][ T1195] Call Trace:
[ 72.571764][ T1195] dump_stack+0x96/0xdb
[ 72.572171][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.572761][ T1195] print_address_description.constprop.5+0x1be/0x360
[ 72.573400][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.573971][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.574544][ T1195] __kasan_report+0x12a/0x16f
[ 72.575014][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.575593][ T1195] kasan_report+0xe/0x20
[ 72.576004][ T1195] ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.576577][ T1195] gtp_build_skb_ip4+0x199/0x1420 [gtp]
[ ... ]
[ 72.647671][ T1195] BUG: unable to handle page fault for address: ffff8880b9a35d28
[ 72.648512][ T1195] #PF: supervisor read access in kernel mode
[ 72.649158][ T1195] #PF: error_code(0x0000) - not-present page
[ 72.649849][ T1195] PGD a6c01067 P4D a6c01067 PUD 11fb07067 PMD 11f939067 PTE 800fffff465ca060
[ 72.652958][ T1195] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 72.653834][ T1195] CPU: 2 PID: 1195 Comm: hping3 Tainted: G B 5.5.0-rc1 #199
[ 72.668062][ T1195] RIP: 0010:ipv4_pdp_find.isra.12+0x86/0x170 [gtp]
[ ... ]
[ 72.679168][ T1195] Call Trace:
[ 72.679603][ T1195] gtp_build_skb_ip4+0x199/0x1420 [gtp]
[ 72.681915][ T1195] ? ipv4_pdp_find.isra.12+0x170/0x170 [gtp]
[ 72.682513][ T1195] ? lock_acquire+0x164/0x3b0
[ 72.682966][ T1195] ? gtp_dev_xmit+0x35e/0x890 [gtp]
[ 72.683481][ T1195] gtp_dev_xmit+0x3c2/0x890 [gtp]
[ ... ]
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c39ea5cba5a2e97fc01b78c85208bf31383b399c ]
Host can provide send indirection table messages anytime after RSS is
enabled by calling rndis_filter_set_rss_param(). So the host provided
table values may be overwritten by the initialization in
rndis_set_subchannel().
To prevent this problem, move the tx_table initialization before calling
rndis_filter_set_rss_param().
Fixes: a6fb6aa3cfa9 ("hv_netvsc: Set tx_table to equal weight after subchannels open")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5d485ed88d48f8101a2067348e267c0aaf4ed486 ]
After the recent fix in commit 1899bb325149 ("bonding: fix state
transition issue in link monitoring"), the active-backup mode with
miimon initially come-up fine but after a link-failure, both members
transition into backup state.
Following steps to reproduce the scenario (eth1 and eth2 are the
slaves of the bond):
ip link set eth1 up
ip link set eth2 down
sleep 1
ip link set eth2 up
ip link set eth1 down
cat /sys/class/net/eth1/bonding_slave/state
cat /sys/class/net/eth2/bonding_slave/state
Fixes: 1899bb325149 ("bonding: fix state transition issue in link monitoring")
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6a902c0f31993ab02e1b6ea7085002b9c9083b6a ]
GTP default hashtable size is 1024 and userspace could set specific
hashtable size with IFLA_GTP_PDP_HASHSIZE. If hashtable size is set to 0
from userspace, hashtable will not work and panic will occur.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 94a6d9fb88df43f92d943c32b84ce398d50bf49f ]
gtp_genl_dump_pdp() is ->dumpit() callback of GTP module and it is used
to dump pdp contexts. it would be re-executed because of dump packet size.
If dump packet size is too big, it saves current dump pointer
(gtp interface pointer, bucket, TID value) then it restarts dump from
last pointer.
Current GTP code allows adding zero TID pdp context but dump code
ignores zero TID value. So, last dump pointer will not be found.
In addition, this patch adds missing rcu_read_lock() in
gtp_genl_dump_pdp().
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f3f2364ea14d1cf6bf966542f31eadcf178f1577 ]
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb043262878 ("net: mvpp2: phylink support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 54fa49ee88138756df0fcf867cb1849904710a8c ]
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6e9105c73f8d2163d12d5dfd762fd75483ed30f5 ]
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bd085ef678b2cc8c38c105673dfe8ff8f5ec0c57 ]
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acca789a358cc960be3937851d7de6591c79d6c2 ]
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 314bd842d98e1035cc40b671a71e07f48420e58f ]
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7e334fc8003c7a38372cc98e7be6082670a47d29 ]
The VF driver also needs to create the health reporters since
VFs are also involved in firmware reset and recovery. Modify
bnxt_dl_register() and bnxt_dl_unregister() so that they can
be called by the VFs to register/unregister devlink. Only the PF
will register the devlink parameters. With devlink registered,
we can now create the health reporters on the VFs.
Fixes: 6763c779c2d8 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 937f188c1f4f89b3fa93ba31fc8587dc1fb14a22 ]
Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed. The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.
Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register(). This allows the
reporters to be adjusted when capabilities change. The same
applies to bnxt_dl_fw_reporters_destroy().
Fixes: 6763c779c2d8 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0797c10d2d1fa0d6f14612404781b348fc757c3e ]
After fixing the allocation of bp->fw_health in the previous patch,
the driver will not go through the fw reset and recovery code paths
if bp->fw_health allocation fails. So we can now remove the
unnecessary NULL checks.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8280b38e01f71e0f89389ccad3fa43b79e57c604 ]
bp->fw_health needs to be allocated for either the firmware initiated
reset feature or the driver initiated error recovery feature. The
current code is not allocating bp->fw_health for all the necessary cases.
This patch corrects the logic to allocate bp->fw_health correctly when
needed. If allocation fails, we clear the feature flags.
We also add the the missing kfree(bp->fw_health) when the driver is
unloaded. If we get an async reset message from the firmware, we also
need to make sure that we have a valid bp->fw_health before proceeding.
Fixes: 07f83d72d238 ("bnxt_en: Discover firmware error recovery capabilities.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c74751f4c39232c31214ec6a3bc1c7e62f5c728b ]
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 325f85f37e5b35807d86185bdf2c64d2980c44ba ]
This will trigger new context memory to be rediscovered and allocated
during the re-probe process after a firmware reset. Without this, the
newly reset firmware does not have valid context memory and the driver
will eventually fail to allocate some resources.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c722ec0a289c7f6b53f89bad1cfb7c4db3f7a62 ]
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323a1 ("bnxt_en: Keep track of reserved IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bd6f48546b9cb7a785344fc78058c420923d7ed8 ]
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1c93fb45761e79b3c00080e71523886cefaf351c ]
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd31f ("net: phy: add driver for aquantia phy")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a5bcd72e054aabb93ddc51ed8cde36a5bfc50271 ]
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7c3125f0a6ebc17846c5908ad7d6056d66c1c426 ]
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Jose Abreu
Chen-Yu Tsai
Andrew Lunn
Eric Dumazet
Haiyang Zhang
Maxim Mikityanskiy
Cristian Birsan
Vishal Kulkarni
Manish Chopra
qize wang
Masashi Honma
Netanel Belgazal
Russell King
Jonathan Lemon
Taehee Yoo
Mahesh Bandewar
Vladimir Oltean
Hangbin Liu
Ido Schimmel
Amit Cohen
Vasundhara Volam
Michael Chan
Martin Blumenstingl
Madalin Bucur
Vladyslav Tarasiuk
Florian Fainelli