aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/intel
AgeCommit message (Collapse)Author
2019-06-01iwlwifi: print fseq info upon fw assertShahar S Matityahu
Read fseq info from FW registers and print it upon fw assert. The print is needed since the fseq version coming from the TLV might not be the actual version that is used. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-01iwlwifi: clear persistence bit according to device familyShahar S Matityahu
The driver attempts to clear persistence bit on any device familiy even though only 9000 and 22000 families require it. Clear the bit only on the relevant device families. Each HW has different address to the write protection register. Use the right register for each HW Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Fixes: 8954e1eb2270 ("iwlwifi: trans: Clear persistence bit when starting the FW") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-01iwlwifi: fix load in rfkill flow for unified firmwareEmmanuel Grumbach
When we have a single image (same firmware image for INIT and OPERATIONAL), we couldn't load the driver and register to the stack if we had hardware RF-Kill asserted. Fix this. This required a few changes: 1) Run the firmware as part of the INIT phase even if its ucode_type is not IWL_UCODE_INIT. 2) Send the commands that are sent to the unified image in INIT flow even in RF-Kill. 3) Don't ask the transport to stop the hardware upon RF-Kill interrupt if the RF-Kill is asserted. 4) Allow the RF-Kill interrupt to take us out of L1A so that the RF-Kill interrupt will be received by the host (to enable the radio). Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-01iwlwifi: mvm: remove d3_sram debugfs fileJohannes Berg
This debugfs file is really old, and cannot work properly since the unified image support. Rather than trying to make it work, which is difficult now due to multiple images (LMAC/UMAC etc.) just remove it - we no longer need it since we properly do a FW coredump even in D3 cases. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 183Thomas Gleixner
Based on 1 normalized pattern(s): gpl license summary [copyright] [c] [2008] [2011] [intel] [corporation] [all] [rights] [reserved] this program is free software you can redistribute it and or modify it under the terms of version 2 of the gnu general public license as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 51 franklin street fifth floor boston ma 02110 usa the full gnu general public license is included in this distribution in the file called license gpl extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 5 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190528170026.622254531@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: "Highlights: 1) Support AES128-CCM ciphers in kTLS, from Vakul Garg. 2) Add fib_sync_mem to control the amount of dirty memory we allow to queue up between synchronize RCU calls, from David Ahern. 3) Make flow classifier more lockless, from Vlad Buslov. 4) Add PHY downshift support to aquantia driver, from Heiner Kallweit. 5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces contention on SLAB spinlocks in heavy RPC workloads. 6) Partial GSO offload support in XFRM, from Boris Pismenny. 7) Add fast link down support to ethtool, from Heiner Kallweit. 8) Use siphash for IP ID generator, from Eric Dumazet. 9) Pull nexthops even further out from ipv4/ipv6 routes and FIB entries, from David Ahern. 10) Move skb->xmit_more into a per-cpu variable, from Florian Westphal. 11) Improve eBPF verifier speed and increase maximum program size, from Alexei Starovoitov. 12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit spinlocks. From Neil Brown. 13) Allow tunneling with GUE encap in ipvs, from Jacky Hu. 14) Improve link partner cap detection in generic PHY code, from Heiner Kallweit. 15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan Maguire. 16) Remove SKB list implementation assumptions in SCTP, your's truly. 17) Various cleanups, optimizations, and simplifications in r8169 driver. From Heiner Kallweit. 18) Add memory accounting on TX and RX path of SCTP, from Xin Long. 19) Switch PHY drivers over to use dynamic featue detection, from Heiner Kallweit. 20) Support flow steering without masking in dpaa2-eth, from Ioana Ciocoi. 21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri Pirko. 22) Increase the strict parsing of current and future netlink attributes, also export such policies to userspace. From Johannes Berg. 23) Allow DSA tag drivers to be modular, from Andrew Lunn. 24) Remove legacy DSA probing support, also from Andrew Lunn. 25) Allow ll_temac driver to be used on non-x86 platforms, from Esben Haabendal. 26) Add a generic tracepoint for TX queue timeouts to ease debugging, from Cong Wang. 27) More indirect call optimizations, from Paolo Abeni" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits) cxgb4: Fix error path in cxgb4_init_module net: phy: improve pause mode reporting in phy_print_status dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings net: macb: Change interrupt and napi enable order in open net: ll_temac: Improve error message on error IRQ net/sched: remove block pointer from common offload structure net: ethernet: support of_get_mac_address new ERR_PTR error net: usb: smsc: fix warning reported by kbuild test robot staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check net: dsa: support of_get_mac_address new ERR_PTR error net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats vrf: sit mtu should not be updated when vrf netdev is the link net: dsa: Fix error cleanup path in dsa_init_module l2tp: Fix possible NULL pointer dereference taprio: add null check on sched_nest to avoid potential null pointer dereference net: mvpp2: cls: fix less than zero check on a u32 variable net_sched: sch_fq: handle non connected flows net_sched: sch_fq: do not assume EDT packets are ordered net: hns3: use devm_kcalloc when allocating desc_cb net: hns3: some cleanup for struct hns3_enet_ring ...
2019-05-06Merge tag 'arm64-mmiowb' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull mmiowb removal from Will Deacon: "Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb()) Remove mmiowb() from the kernel memory barrier API and instead, for architectures that need it, hide the barrier inside spin_unlock() when MMIO has been performed inside the critical section. The only relatively recent changes have been addressing review comments on the documentation, which is in a much better shape thanks to the efforts of Ben and Ingo. I was initially planning to split this into two pull requests so that you could run the coccinelle script yourself, however it's been plain sailing in linux-next so I've just included the whole lot here to keep things simple" * tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits) docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section arch: Remove dummy mmiowb() definitions from arch code net/ethernet/silan/sc92031: Remove stale comment about mmiowb() i40iw: Redefine i40iw_mmiowb() to do nothing scsi/qla1280: Remove stale comment about mmiowb() drivers: Remove explicit invocations of mmiowb() drivers: Remove useless trailing comments from mmiowb() invocations Documentation: Kill all references to mmiowb() riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() m68k/io: Remove useless definition of mmiowb() nds32/io: Remove useless definition of mmiowb() x86/io: Remove useless definition of mmiowb() arm64/io: Remove useless definition of mmiowb() ARM/io: Remove useless definition of mmiowb() mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors ...
2019-05-05Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.2 Most likely the last patchset of new feature for 5.2, and this time we have quite a lot of new features. Most obvious being rtw88 from Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We have also new hardware support for existing drivers and improvements. There's one conflict in iwlwifi, my example conflict resolution below. Major changes: iwlwifi * bump the 20000-series FW API version * work on new hardware continues * RTT confidence indication support for Fine Timing Measurement (FTM) * an improvement in HE (802.11ax) rate-scaling * add command version parsing from the fimware TLVs * add support for a new WoWLAN patterns firmware API rsi * add support for rs9116 mwifiex * add support for SD8987 brcmfmac * add quirk for ACEPC T8 and T11 mini PCs rt2x00 * add RT3883 support qtnfmac * fix debugfs interface to support multiple cards rtw88 * new driver mt76 * share more code across drivers * add support for MT7615 chipset * rework DMA API * tx/rx performance optimizations * use NAPI for tx cleanup on mt76x02 * AP mode support for USB devices * USB stability fixes * tx power handling fixes for 76x2 * endian fixes Conflicts: There's a trivial conflict in drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be just empty: diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h index cd622af90077,b0671e16e1ce..000000000000 --- a/drivers/net/wireless/intel/iwlwifi/fw/file.h +++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three trivial overlapping conflicts. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-29iwlwifi: dbg_ini: check for valid region type during regions parsingShahar S Matityahu
Add region type checking during regions parsing to avoid attempts to parse unsupported or illegal region types. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: avoid allocating memory for region with disabled domainShahar S Matityahu
In iwl_fw_ini_get_trigger_len the driver allocates space for memory regions regardless of their domain and in iwl_fw_ini_dump_trigger the driver aborts trigger collection of disabled domain. This diff causes unneeded memory allocation and traling zeros in the dump file. Solve this behavior by enforcing domain checking in iwl_fw_ini_get_trigger_len Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: dbg: replace dump info device family with HW typeShahar S Matityahu
In the dump info, the driver sets device_family to IWL_FW_ERROR_DUMP_FAMILY_7 in case IWL_FW_ERROR_DUMP_FAMILY_7 is used or IWL_FW_ERROR_DUMP_FAMILY_8 otherwise. This information is misleading and incorrect since the driver sets the device family to 8 to any device that is from family 8 and later, e.g. device family 9 is represented as 8 in the dump. Also, the device family enum is known only to the driver and does not give any information to the FW developer Change the device family to HW type to give propper data about the nic in use. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: dbg_ini: add periodic trigger supportShahar S Matityahu
Allows to configure a periodic data collection Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: dbg_ini: add lmac and umac error tables dumping supportShahar S Matityahu
Add LMAC_ERROR_TABLE and UMAC_ERROR_TABLE region types and handle them in the same way as we handle DEVICE_MEMORY. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: parse command version TLVJohannes Berg
In newer firmware images there's a command version TLV that states, for each listed command or notification, which version of the command and/or notification structure is used. Read and keep this data to be able to use it in the future. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: pcie: remove stray character in iwl_pcie_rx_alloc_page()Luca Coelho
We have a solitary and inconspicous ` in the middle of a comment in this function, which should not be there. Remove it. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: mvm: Don't sleep in RX pathAndrei Otcheretianski
Don't use cancel_delayed_work_sync() inside the channel switch notifications as they are handled synchronously as part of the RX path. Fix that by replacing it with cancel_delayed_work(). This should be safe as we don't really care whether the work is already started and in such case we would disconnect anyway. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: bump FW API to 48 for 22000 seriesLuca Coelho
Start supporting API version 48 for 22000 series. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: mvm: limit TLC according to our HE capabilitiesLiad Kaufman
Instead of setting the TLC config command according to the rates the peer supports, make sure that we aren't also limited by our own rates, so take the minimum between the peer's supported RX rates and our supported TX rates. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: support fseq tlv and print fseq versionShahar S Matityahu
Support fseq tlv and print fseq version to dmesg. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: mvm: report FTM start time TSF when applicableAvraham Stern
When the interface that is requesting an FTM measurement is connected to a BSS, it is possible that the FTM request was originated by an RRM request from the AP. In this case the station needs to report the measurement start time in terms of the TSF of the AP. Since there is no indication in the FTM request itself if the TSF is needed, always report the TSF if the station is associated. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: mvm: support v2 of the WoWLAN patterns commandLuca Coelho
Add new definitions for the WoWLAN patterns API version 2 and support for version 2 of the WoWLAN patterns command without implementing the new features. With this commit we only supporting the existing bitmask pattern match. Use the new version only if the TLV is set. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: pcie: don't crash on invalid RX interruptJohannes Berg
If for some reason the device gives us an RX interrupt before we're ready for it, perhaps during device power-on with misconfigured IRQ causes mapping or so, we can crash trying to access the queues. Prevent that by checking that we actually have RXQs and that they were properly allocated. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: pcie: initialize debug_rfkill to -1Johannes Berg
This will let us introduce a mechanism to start with rfkill faked, and put 0 here to override it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: Use correct channel_profile iniwl_get_nvmYueHaibing
commit 2785ce008e3b ("iwlwifi: support new NVM response API") seems forgot use correct channel_profile in iwl_get_nvm when call iwl_init_sbands(). Fixes: 2785ce008e3b ("iwlwifi: support new NVM response API") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-28iwlwifi: mvm: fix merge damage in iwl_mvm_vif_dbgfs_register()Luca Coelho
When I rebased Greg's patch, I accidentally left the old if block that was already there. Remove it. Fixes: 154d4899e411 ("iwlwifi: mvm: properly check debugfs dentry before using it") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-28iwlwifi: fix driver operation for 5350Emmanuel Grumbach
We introduced a bug that prevented this old device from working. The driver would simply not be able to complete the INIT flow while spewing this warning: CSR addresses aren't configured WARNING: CPU: 0 PID: 819 at drivers/net/wireless/intel/iwlwifi/pcie/drv.c:917 iwl_pci_probe+0x160/0x1e0 [iwlwifi] Cc: stable@vger.kernel.org # v4.18+ Fixes: a8cbb46f831d ("iwlwifi: allow different csr flags for different device families") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Fixes: c8f1b51e506d ("iwlwifi: allow different csr flags for different device families") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-28iwlwifi: mvm: check for length correctness in iwl_mvm_create_skb()Luca Coelho
We don't check for the validity of the lengths in the packet received from the firmware. If the MPDU length received in the rx descriptor is too short to contain the header length and the crypt length together, we may end up trying to copy a negative number of bytes (headlen - hdrlen < 0) which will underflow and cause us to try to copy a huge amount of data. This causes oopses such as this one: BUG: unable to handle kernel paging request at ffff896be2970000 PGD 5e201067 P4D 5e201067 PUD 5e205067 PMD 16110d063 PTE 8000000162970161 Oops: 0003 [#1] PREEMPT SMP NOPTI CPU: 2 PID: 1824 Comm: irq/134-iwlwifi Not tainted 4.19.33-04308-geea41cf4930f #1 Hardware name: [...] RIP: 0010:memcpy_erms+0x6/0x10 Code: 90 90 90 90 eb 1e 0f 1f 00 48 89 f8 48 89 d1 48 c1 e9 03 83 e2 07 f3 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48 89 d1 <f3> a4 c3 0f 1f 80 00 00 00 00 48 89 f8 48 83 fa 20 72 7e 40 38 fe RSP: 0018:ffffa4630196fc60 EFLAGS: 00010287 RAX: ffff896be2924618 RBX: ffff896bc8ecc600 RCX: 00000000fffb4610 RDX: 00000000fffffff8 RSI: ffff896a835e2a38 RDI: ffff896be2970000 RBP: ffffa4630196fd30 R08: ffff896bc8ecc600 R09: ffff896a83597000 R10: ffff896bd6998400 R11: 000000000200407f R12: ffff896a83597050 R13: 00000000fffffff8 R14: 0000000000000010 R15: ffff896a83597038 FS: 0000000000000000(0000) GS:ffff896be8280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffff896be2970000 CR3: 000000005dc12002 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: iwl_mvm_rx_mpdu_mq+0xb51/0x121b [iwlmvm] iwl_pcie_rx_handle+0x58c/0xa89 [iwlwifi] iwl_pcie_irq_rx_msix_handler+0xd9/0x12a [iwlwifi] irq_thread_fn+0x24/0x49 irq_thread+0xb0/0x122 kthread+0x138/0x140 ret_from_fork+0x1f/0x40 Fix that by checking the lengths for correctness and trigger a warning to show that we have received wrong data. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-27netlink: make validation more configurable for future strictnessJohannes Berg
We currently have two levels of strict validation: 1) liberal (default) - undefined (type >= max) & NLA_UNSPEC attributes accepted - attribute length >= expected accepted - garbage at end of message accepted 2) strict (opt-in) - NLA_UNSPEC attributes accepted - attribute length >= expected accepted Split out parsing strictness into four different options: * TRAILING - check that there's no trailing data after parsing attributes (in message or nested) * MAXTYPE - reject attrs > max known type * UNSPEC - reject attributes with NLA_UNSPEC policy entries * STRICT_ATTRS - strictly validate attribute size The default for future things should be *everything*. The current *_strict() is a combination of TRAILING and MAXTYPE, and is renamed to _deprecated_strict(). The current regular parsing has none of this, and is renamed to *_parse_deprecated(). Additionally it allows us to selectively set one of the new flags even on old policies. Notably, the UNSPEC flag could be useful in this case, since it can be arranged (by filling in the policy) to not be an incompatible userspace ABI change, but would then going forward prevent forgetting attribute entries. Similar can apply to the POLICY flag. We end up with the following renames: * nla_parse -> nla_parse_deprecated * nla_parse_strict -> nla_parse_deprecated_strict * nlmsg_parse -> nlmsg_parse_deprecated * nlmsg_parse_strict -> nlmsg_parse_deprecated_strict * nla_parse_nested -> nla_parse_nested_deprecated * nla_validate_nested -> nla_validate_nested_deprecated Using spatch, of course: @@ expression TB, MAX, HEAD, LEN, POL, EXT; @@ -nla_parse(TB, MAX, HEAD, LEN, POL, EXT) +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression TB, MAX, NLA, POL, EXT; @@ -nla_parse_nested(TB, MAX, NLA, POL, EXT) +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT) @@ expression START, MAX, POL, EXT; @@ -nla_validate_nested(START, MAX, POL, EXT) +nla_validate_nested_deprecated(START, MAX, POL, EXT) @@ expression NLH, HDRLEN, MAX, POL, EXT; @@ -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT) +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT) For this patch, don't actually add the strict, non-renamed versions yet so that it breaks compile if I get it wrong. Also, while at it, make nla_validate and nla_parse go down to a common __nla_validate_parse() function to avoid code duplication. Ultimately, this allows us to have very strict validation for every new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the next patch, while existing things will continue to work as is. In effect then, this adds fully strict validation for any new command. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-25iwlegacy: fix spelling mistake "acumulative" -> "accumulative"Colin Ian King
Fix spelling mistakes in rx stats text. I missed these from an earlier round of fixing the same spelling mistake. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-19iwlwifi: dbg_ini: set dump bit only when trigger collection is certainShahar S Matityahu
In case the the trigger occurrences is zero or force_restart is set, the driver sets IWL_FWRT_STATUS_DUMPING without actually scheduling trigger collection. At this point no other dump collection can be performed. Solve this by setting IWL_FWRT_STATUS_DUMPING bit only when the driver is surely going to schedule dump collection Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: mvm: Change an 'else if' into an 'else' in iwl_mvm_send_add_bcast_staNathan Chancellor
When building with -Wsometimes-uninitialized, Clang warns: drivers/net/wireless/intel/iwlwifi/mvm/sta.c:2114:12: warning: variable 'queue' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] Clang can't evaluate at this point that WARN(1, ...) always returns true because __ret_warn_on is defined as !!(condition), which isn't immediately evaluated as 1. Change this branch to else so that it's clear to Clang that we intend to bail out here. Link: https://github.com/ClangBuiltLinux/linux/issues/399 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> [added a few more braces] Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: remove unused 0x40C0 PCI device IDsLuca Coelho
This device ID and device type was never released, so we can remove it from the PCI IDs list. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: mvm: support rtt confidence indicationAvraham Stern
The range response notification API has changed to add a value that indicates the confidence of the rtt result. Support the new API and print the rtt confidence for debug. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: dbg: add lmac and umac PC registers to periphery dumpShahar S Matityahu
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: dbg: add periphery memory dumping support to ax210 device familyShahar S Matityahu
Allows to dump periphery memory on ax210 devices. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: rs: consider LDPC capability in case of HEGregory Greenman
When building TLC configuration command, consider in case of HE, if LDPC support is turned on in our capabilities. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: dbg_ini: add debug prints to the ini flowsShahar S Matityahu
Add debug prints to the ini flow and rewrite existing prints to provide more information Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: add FW_INFO debug levelShahar S Matityahu
Add FW_INFO debug level. This level is enabled if INFO or FW debug levels are set. Also, set fw request and callback prints under this debug level. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: dbg_ini: support notification and dhc regions type parsingShahar S Matityahu
IWL_FW_INI_REGION_CSR and IWL_FW_INI_REGION_NOTIFICATION does not have memory addresses attached to them so the driver should skip them when parsing the region tlv. Also, instead of declearing what region types should skip the addition of the memory addresses, declare what regions have addition of memory addresses. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: unite macros with same meaningShaul Triebitz
TFD_*_SLOTS and IWL_*_QUEUE_SIZE both define the TX queue size (number of TFDs). Get rid of TFD_*_SLOTS and use only IWL_*_QUEUE_SIZE. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: mvm: set 512 TX queue slots for AX210 devicesShaul Triebitz
AX210 devices support 256 BA (256 MPDUs in an AMPDU). The firmware requires that the number of TFDs will be minimum twice as big as the BA size (2 * 256 = 512). Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: bump FW API to 47 for 22000 seriesLuca Coelho
Start supporting API version 47 for 22000 series. The 9000 series is now frozen on version 46. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.2 Nothing really special standing out this time, iwlwifi being the most active driver. Major changes: iwlwifi * send NO_DATA events so they can be captured in radiotap * support for multiple BSSID * support for some new FW API versions * support new hardware * debugfs cleanups by Greg-KH qtnfmac * allow each MAC to specify its own regulatory rules ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-18iwlwifi: cfg: use family 22560 based_params for AX210 familyShaul Triebitz
Specifically, max_tfd_queue_size should be 0x10000 like in 22560 family and not 0x100 like in 22000 family. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18iwlwifi: mvm: properly check debugfs dentry before using itGreg Kroah-Hartman
debugfs can now report an error code if something went wrong instead of just NULL. So if the return value is to be used as a "real" dentry, it needs to be checked if it is an error before dereferencing it. This is now happening because of ff9fb72bc077 ("debugfs: return error values, not NULL"). If multiple iwlwifi devices are in the system, this can cause problems when the driver attempts to create the main debugfs directory again. Later on in the code we fail horribly by trying to dereference a pointer that is an error value. Reported-by: Laura Abbott <labbott@redhat.com> Reported-by: Gabriel Ramirez <gabriello.ramirez@gmail.com> Cc: Johannes Berg <johannes.berg@intel.com> Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Cc: Luca Coelho <luciano.coelho@intel.com> Cc: Intel Linux Wireless <linuxwifi@intel.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: stable <stable@vger.kernel.org> # 5.0 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18iwlwifi: dbg_ini: check debug TLV type explicitlyShahar S Matityahu
In ini debug TLVs bit 24 is set. The driver relies on it in the memory allocation for the debug configuration. This implementation is problematic in case of a new debug TLV that is not supported yet is added and uses bit 24. In such a scenario the driver allocate space without using it which causes errors in the apply point enabling flow. Solve it by explicitly checking if a given TLV is part of the list of the supported ini debug TLVs. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Fixes: f14cda6f3b31 ("iwlwifi: trans: parse and store debug ini TLVs") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18iwlwifi: mvm: don't attempt debug collection in rfkillJohannes Berg
If we fail to initialize because rfkill is enabled, then trying to do debug collection currently just fails. Prevent that in the high-level code, although we should probably also fix the lower level code to do things more carefully. It's not 100% clear that it fixes this commit, as the original dump code at the time might've been more careful. In any case, we don't really need to dump anything in this expected scenario. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 7125648074e8 ("iwlwifi: add fw dump upon RT ucode start failure") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18iwlwifi: don't panic in error path on non-msix systemsShahar S Matityahu
The driver uses msix causes-register to handle both msix and non msix interrupts when performing sync nmi. On devices that do not support msix this register is unmapped and accessing it causes a kernel panic. Solve this by differentiating the two cases and accessing the proper causes-register in each case. Reported-by: Michal Hocko <mhocko@kernel.org> Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
generated by cgit 1.2.3-korg (git 2.39.0) at 2024-07-01 20:35:11 +0000