aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/ath10k
AgeCommit message (Collapse)Author
2018-06-28ath10k: update the phymode along with bandwidth change requestRyan Hsu
In the case of Station connects to AP with narrower bandwidth at beginning. And later the AP changes the bandwidth to winder bandwidth, the AP will beacon with wider bandwidth IE, eg VHT20->VHT40->VHT80 or VHT40->VHT80. Since the supported BANDWIDTH will be limited by the PHYMODE, so while Station receives the bandwidth change request, it will also need to reconfigure the PHYMODE setting to firmware instead of just configuring the BANDWIDTH info, otherwise it'll trigger a firmware crash with non-support bandwidth. The issue was observed in WLAN.RM.4.4.1-00051-QCARMSWP-1, QCA6174 with below scenario: AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz) disconnect from AP xxx for new auth to yyy RX ReassocResp from xxx (capab=0x1111 status=0 aid=102) associated .... AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz) AP xxx changed bandwidth, new config is 5200 MHz, width 3 (5210/0 MHz) .... firmware register dump: [00]: 0x05030000 0x000015B3 0x00987291 0x00955B31 [04]: 0x00987291 0x00060730 0x00000004 0x00000001 [08]: 0x004089F0 0x00955A00 0x000A0B00 0x00400000 [12]: 0x00000009 0x00000000 0x00952CD0 0x00952CE6 [16]: 0x00952CC4 0x0098E25F 0x00000000 0x0091080D [20]: 0x40987291 0x0040E7A8 0x00000000 0x0041EE3C [24]: 0x809ABF05 0x0040E808 0x00000000 0xC0987291 [28]: 0x809A650C 0x0040E948 0x0041FE40 0x004345C4 [32]: 0x809A5C63 0x0040E988 0x0040E9AC 0x0042D1A8 [36]: 0x8091D252 0x0040E9A8 0x00000002 0x00000001 [40]: 0x809FDA9D 0x0040EA58 0x0043D554 0x0042D554 [44]: 0x809F8B22 0x0040EA78 0x0043D554 0x00000001 [48]: 0x80911210 0x0040EAC8 0x00000010 0x004041D0 [52]: 0x80911154 0x0040EB28 0x00400000 0x00000000 [56]: 0x8091122D 0x0040EB48 0x00000000 0x00400600 Reported-by: Rouven Czerwinski <rouven@czerwinskis.de> Tested-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Add Maglev hashing scheduler to IPVS, from Inju Song. 2) Lots of new TC subsystem tests from Roman Mashak. 3) Add TCP zero copy receive and fix delayed acks and autotuning with SO_RCVLOWAT, from Eric Dumazet. 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard Brouer. 5) Add ttl inherit support to vxlan, from Hangbin Liu. 6) Properly separate ipv6 routes into their logically independant components. fib6_info for the routing table, and fib6_nh for sets of nexthops, which thus can be shared. From David Ahern. 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP messages from XDP programs. From Nikita V. Shirokov. 8) Lots of long overdue cleanups to the r8169 driver, from Heiner Kallweit. 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau. 10) Add traffic condition monitoring to iwlwifi, from Luca Coelho. 11) Plumb extack down into fib_rules, from Roopa Prabhu. 12) Add Flower classifier offload support to igb, from Vinicius Costa Gomes. 13) Add UDP GSO support, from Willem de Bruijn. 14) Add documentation for eBPF helpers, from Quentin Monnet. 15) Add TLS tx offload to mlx5, from Ilya Lesokhin. 16) Allow applications to be given the number of bytes available to read on a socket via a control message returned from recvmsg(), from Soheil Hassas Yeganeh. 17) Add x86_32 eBPF JIT compiler, from Wang YanQing. 18) Add AF_XDP sockets, with zerocopy support infrastructure as well. From Björn Töpel. 19) Remove indirect load support from all of the BPF JITs and handle these operations in the verifier by translating them into native BPF instead. From Daniel Borkmann. 20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha. 21) Allow XDP programs to do lookups in the main kernel routing tables for forwarding. From David Ahern. 22) Allow drivers to store hardware state into an ELF section of kernel dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy. 23) Various RACK and loss detection improvements in TCP, from Yuchung Cheng. 24) Add TCP SACK compression, from Eric Dumazet. 25) Add User Mode Helper support and basic bpfilter infrastructure, from Alexei Starovoitov. 26) Support ports and protocol values in RTM_GETROUTE, from Roopa Prabhu. 27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard Brouer. 28) Add lots of forwarding selftests, from Petr Machata. 29) Add generic network device failover driver, from Sridhar Samudrala. * ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits) strparser: Add __strp_unpause and use it in ktls. rxrpc: Fix terminal retransmission connection ID to include the channel net: hns3: Optimize PF CMDQ interrupt switching process net: hns3: Fix for VF mailbox receiving unknown message net: hns3: Fix for VF mailbox cannot receiving PF response bnx2x: use the right constant Revert "net: sched: cls: Fix offloading when ingress dev is vxlan" net: dsa: b53: Fix for brcm tag issue in Cygnus SoC enic: fix UDP rss bits netdev-FAQ: clarify DaveM's position for stable backports rtnetlink: validate attributes in do_setlink() mlxsw: Add extack messages for port_{un, }split failures netdevsim: Add extack error message for devlink reload devlink: Add extack to reload and port_{un, }split operations net: metrics: add proper netlink validation ipmr: fix error path when ipmr_new_table fails ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds net: hns3: remove unused hclgevf_cfg_func_mta_filter netfilter: provide udp*_lib_lookup for nf_tproxy qed*: Utilize FW 8.37.2.0 ...
2018-05-25ath10k: DFS Host ConfirmationSriram R
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag. This new features enables the ath10k host to send information to the firmware on the specifications of detected radar type. This allows the firmware to validate if the host's radar pattern detector unit is operational and check if the radar information shared by host matches the radar pulses sent as phy error events from firmware. If the check fails the firmware won't allow use of DFS channels on AP mode when using FCC regulatory region. Hence this patch is mandatory when using a firmware from 10.4-3.6 branch. Else, DFS channels on FCC regions cannot be used. Supported Chipsets : QCA9984/QCA9888/QCA4019 Firmware Version : 10.4-3.6-00104 Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: add support to get the detected radar specificationsSriram R
This enables ath10k/ath9k drivers to collect the specifications of the radar type once it is detected by the dfs pattern detector unit. Usage of the collected info is specific to driver implementation. For example, collected radar info could be used by the host driver to send to co-processors for additional processing/validation. Note: 'radar_detector_specs' data containing the specifications of different radar types which was private within dfs_pattern_detector/ dfs_pri_detector is now shared with drivers as well for making use of this information. Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath10k: remove useless test before clk_disable_unprepareYueHaibing
clk_disable_unprepare() already checks that the clock pointer is valid. No need to test it before calling it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath10k: add support to configure channel dwell timePradeep Kumar Chitrapu
Configure channel dwell time from duration of the scan request received from mac80211 when the duration is non-zero. When the scan request does not have duration value, use the default ones, the current implementation. Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is advertized. Supported Chipsets: -QCA988X/QCA9887 PCI -QCA99X0/QCA9984/QCA9888/QCA4019 PCI -QCA6174/QCA9377 PCI/USB/SDIO -WCN3990 SNOC Tested on QCA9984 with firmware ver 10.4-3.6-0010 Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath10k: add memory dump support for QCA9888 and QCA99X0Anilkumar Kolli
This patch adds firmware crash memory dump support for QCA9888 and QCA99X0. Tested on: QCA9888 firmware 10.4-3.5.3-00053 QCA99X0 firmware 10.4.1.00030-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-14ath10k: re-enable the firmware fallback mechanism for testmodeAndres Rodriguez
The ath10k testmode uses request_firmware_direct() in order to avoid producing firmware load warnings. Disabling the fallback mechanism was a side effect of disabling warnings. We now have a new API that allows us to avoid warnings while keeping the fallback mechanism enabled. So use that instead. Signed-off-by: Andres Rodriguez <andresx7@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14ath10k: use firmware_request_nowarn() to load firmwareAndres Rodriguez
This reduces the unnecessary spew when trying to load optional firmware: "Direct firmware load for ... failed with error -2" Signed-off-by: Andres Rodriguez <andresx7@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-12ath10k: replace bit shifts with the BIT() macro for rx desc bitsGovind Singh
Use the BIT() macro from 'linux/bitops.h' to define the rx desc bit flags to have consistency with new definitions. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-12ath10k: hw: make consistent usage of ATH10K_FW_DIR in pathsMarcus Folkesson
For some reason not all entries used ATH10K_FW_DIR so fix that. No functional changes. Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-12ath10k: remove variables which set but not usedKenneth Lu
Variable buf_len and num_vdev_stats are being assigned but never read. These are redundant and can be remove. Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-12ath10k: fix return value check in wake_tx_q opErik Stromdahl
ath10k_mac_tx_push_txq returns either a postive integer (length) on success or a negative error code on error. The "if (ret) break;" statement will thus always break out of the loop immediately after ath10k_mac_tx_push_txq has returned (making the loop pointless). A side effect of this fix is that we will iterate the queue until ath10k_mac_tx_push_txq returns -ENOENT. This will make sure the queue is not added back to ar->txqs when it is empty. This could potentially improve performance somewhat (I have seen a small improvement with SDIO devices). Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-12ath10k: snoc: Remove owner assignment from platform_driverFabio Estevam
Structure platform_driver does not need to set the owner field, as this will be populated by the driver core. Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-12ath10k: add quiet mode support for QCA6174/QCA9377Yu Wang
To enable thermal throttling for QCA6174 and QCA9377, implement gen_pdev_set_quiet_mode for them. With this change, quiet period for QCA6174/QCA9377 can be also set/get via debugfs. Usage: To set quiet period: echo <period> > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period To get the current quiet period: cat /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period This change has been verified with QCA6174 hw3.2(fw: WLAN_RM.4.4.1-00102-QCARMSWP-1). Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-27ath10k: sdio: jump to correct label in error handling pathNiklas Cassel
Jump to the correct label in error handling path. At this point of execution create_singlethread_workqueue() has succeeded, so it should be properly destroyed. Jump label was renamed in commit ec2c64e20257 ("ath10k: sdio: fix memory leak for probe allocations"). However, the bug was originally introduced in commit d96db25d2025 ("ath10k: add initial SDIO support"). Fixes: d96db25d2025 ("ath10k: add initial SDIO support") Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-27ath10k: fix spelling mistake: "servive" -> "service"Colin Ian King
Trivial fix to spelling mistake in ath10k_warn warning message text Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-27ath10k: fix kernel panic while reading tpc_statsTamizh Chelvam
When attempt to read tpc_stats for the chipsets which support more than 3 tx chain will trigger kernel panic(kernel stack is corrupted) due to writing values on rate_code array out of range. This patch changes the array size depends on the WMI_TPC_TX_N_CHAIN and added check to avoid write values on the array if the num tx chain get in tpc config event is greater than WMI_TPC_TX_N_CHAIN. Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00057 Kernel panic log : [ 323.510944] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: bf90c654 [ 323.510944] [ 323.524390] CPU: 0 PID: 1908 Comm: cat Not tainted 3.14.77 #31 [ 323.530224] [<c021db48>] (unwind_backtrace) from [<c021ac08>] (show_stack+0x10/0x14) [ 323.537941] [<c021ac08>] (show_stack) from [<c03c53c0>] (dump_stack+0x80/0xa0) [ 323.545146] [<c03c53c0>] (dump_stack) from [<c022e4ac>] (panic+0x84/0x1e4) [ 323.552000] [<c022e4ac>] (panic) from [<c022e61c>] (__stack_chk_fail+0x10/0x14) [ 323.559350] [<c022e61c>] (__stack_chk_fail) from [<bf90c654>] (ath10k_wmi_event_pdev_tpc_config+0x424/0x438 [ath10k_core]) [ 323.570471] [<bf90c654>] (ath10k_wmi_event_pdev_tpc_config [ath10k_core]) from [<bf90d800>] (ath10k_wmi_10_4_op_rx+0x2f0/0x39c [ath10k_core]) [ 323.583047] [<bf90d800>] (ath10k_wmi_10_4_op_rx [ath10k_core]) from [<bf8fcc18>] (ath10k_htc_rx_completion_handler+0x170/0x1a0 [ath10k_core]) [ 323.595702] [<bf8fcc18>] (ath10k_htc_rx_completion_handler [ath10k_core]) from [<bf961f44>] (ath10k_pci_hif_send_complete_check+0x1f0/0x220 [ath10k_pci]) [ 323.609421] [<bf961f44>] (ath10k_pci_hif_send_complete_check [ath10k_pci]) from [<bf96562c>] (ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]) [ 323.622490] [<bf96562c>] (ath10k_ce_per_engine_service [ath10k_pci]) from [<bf9656f0>] (ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]) [ 323.635423] [<bf9656f0>] (ath10k_ce_per_engine_service_any [ath10k_pci]) from [<bf96365c>] (ath10k_pci_napi_poll+0x44/0xe8 [ath10k_pci]) [ 323.647665] [<bf96365c>] (ath10k_pci_napi_poll [ath10k_pci]) from [<c0599994>] (net_rx_action+0xac/0x160) [ 323.657208] [<c0599994>] (net_rx_action) from [<c02324a4>] (__do_softirq+0x104/0x294) [ 323.665017] [<c02324a4>] (__do_softirq) from [<c0232920>] (irq_exit+0x9c/0x11c) [ 323.672314] [<c0232920>] (irq_exit) from [<c0217fc0>] (handle_IRQ+0x6c/0x90) [ 323.679341] [<c0217fc0>] (handle_IRQ) from [<c02084e0>] (gic_handle_irq+0x3c/0x60) [ 323.686893] [<c02084e0>] (gic_handle_irq) from [<c02095c0>] (__irq_svc+0x40/0x70) [ 323.694349] Exception stack(0xdd489c58 to 0xdd489ca0) [ 323.699384] 9c40: 00000000 a0000013 [ 323.707547] 9c60: 00000000 dc4bce40 60000013 ddc1d800 dd488000 00000990 00000000 c085c800 [ 323.715707] 9c80: 00000000 dd489d44 0000092d dd489ca0 c026e664 c026e668 60000013 ffffffff [ 323.723877] [<c02095c0>] (__irq_svc) from [<c026e668>] (rcu_note_context_switch+0x170/0x184) [ 323.732298] [<c026e668>] (rcu_note_context_switch) from [<c020e928>] (__schedule+0x50/0x4d4) [ 323.740716] [<c020e928>] (__schedule) from [<c020e490>] (schedule_timeout+0x148/0x178) [ 323.748611] [<c020e490>] (schedule_timeout) from [<c020f804>] (wait_for_common+0x114/0x154) [ 323.756972] [<c020f804>] (wait_for_common) from [<bf8f6ef0>] (ath10k_tpc_stats_open+0xc8/0x340 [ath10k_core]) [ 323.766873] [<bf8f6ef0>] (ath10k_tpc_stats_open [ath10k_core]) from [<c02bb598>] (do_dentry_open+0x1ac/0x274) [ 323.776741] [<c02bb598>] (do_dentry_open) from [<c02c838c>] (do_last+0x8c0/0xb08) [ 323.784201] [<c02c838c>] (do_last) from [<c02c87e4>] (path_openat+0x210/0x598) [ 323.791408] [<c02c87e4>] (path_openat) from [<c02c9d1c>] (do_filp_open+0x2c/0x78) [ 323.798873] [<c02c9d1c>] (do_filp_open) from [<c02bc85c>] (do_sys_open+0x114/0x1b4) [ 323.806509] [<c02bc85c>] (do_sys_open) from [<c0208c80>] (ret_fast_syscall+0x0/0x44) [ 323.814241] CPU1: stopping [ 323.816927] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.77 #31 [ 323.823008] [<c021db48>] (unwind_backtrace) from [<c021ac08>] (show_stack+0x10/0x14) [ 323.830731] [<c021ac08>] (show_stack) from [<c03c53c0>] (dump_stack+0x80/0xa0) [ 323.837934] [<c03c53c0>] (dump_stack) from [<c021cfac>] (handle_IPI+0xb8/0x140) [ 323.845224] [<c021cfac>] (handle_IPI) from [<c02084fc>] (gic_handle_irq+0x58/0x60) [ 323.852774] [<c02084fc>] (gic_handle_irq) from [<c02095c0>] (__irq_svc+0x40/0x70) [ 323.860233] Exception stack(0xdd499fa0 to 0xdd499fe8) [ 323.865273] 9fa0: ffffffed 00000000 1d3c9000 00000000 dd498000 dd498030 10c0387d c08b62c8 [ 323.873432] 9fc0: 4220406a 512f04d0 00000000 00000000 00000001 dd499fe8 c021838c c0218390 [ 323.881588] 9fe0: 60000013 ffffffff [ 323.885070] [<c02095c0>] (__irq_svc) from [<c0218390>] (arch_cpu_idle+0x30/0x50) [ 323.892454] [<c0218390>] (arch_cpu_idle) from [<c026500c>] (cpu_startup_entry+0xa4/0x108) [ 323.900690] [<c026500c>] (cpu_startup_entry) from [<422085a4>] (0x422085a4) Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-27ath10k: fix information leak in debugfsVenkateswara Naralasetty
During write to some of debugfs in ath10k, few variables exposing stack data when process user input. which leads to possible information leak. This patch fix this issue by initializing buffer and checks the return valure of 'simple_write_to_buffer'. Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: enable sta idle power saveGovind Singh
Enable sta power save in fw for the targets that supports idle power save. The idle ps enable command will be ignored by the firmware which does not support this feature. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: enable SRRI/DRRI support on ddr for WCN3990Govind Singh
SRRI/DRRI are not mapped in the HW Shadow block and can lead to un-clocked access if common subsystem in the target is powered down due to idle mode. To mitigate this problem SRRI/DRRI can be read from DDR instead of doing an actual hardware read. Host allocates non cached memory on ddr and configures the physical address of this memory to the CE hardware. The hardware updates the RRI on this particular location. Read SRRI/DRRI from DDR location instead of direct target read. Enable retention restore on ddr using hw params to enable in specific targets. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: add support for shadow register for WNC3990Rakesh Pillai
WCN3990 needs shadow register write operation support for copy engine for regular operation in powersave mode. Add support for copy engine shadow register write in datapath tx for WCN3990 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: add hw params for shadow register supportRakesh Pillai
wcn3990 supports shadow register for ce write. Add a hw param for shadow register support. Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: enable hw checksum for wcn3990Rakesh Pillai
By default ath10k driver enables the support for HW_CHECKSUM (NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets and all patckets are dropped. But due note that wcn3990 support in ath10k is still incomplete so this isn't a critical fix (yet). Enable hw checksum calculations in wcn3990 hardware by setting the proper flags in msdu descriptor tso flags. Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: convert wow pattern from 802.3 to 802.11Wen Gong
When trying to set wow wakeup patterns it fails with this command: iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx The reason is that the wow pattern from upper layer is in 802.3 format for this case, it need to convert it to 802.11 format. The input offset parameter is used for 802.3, but the actual offset firmware need depends on rx_decap_mode, so that it needs to be recalculated. Pattern of 802.3 packet is not same with 802.11 packet. If the rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will receive data packet with 802.11 format from hardware. Tested with QCA6174 hw3.0 with firmware WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377. This has always failed, so it's not a regression with new firmware releases. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: support MAC address randomization in scanCarl Huang
The ath10k reports the random_mac_addr capability to upper layer based on the service bit firmware reported. Driver sets the spoofed flag in scan_ctrl_flag to firmware if upper layer has enabled this feature in scan request. Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1, but QCA9377 is also affected. Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: add WMI_SERVICE_AVAILABLE_EVENT supportCarl Huang
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT, the 128bit service map in WMI_SERVICE_READY_EVENT is not enough for firmware to notice new WLAN service to host driver. Hereby, for thoese new WLAN service, firmware will notice host driver by WMI_SERVICE_AVAILABLE_EVENT. Signed-off-by: Alan Liu <alanliu@codeaurora.org> Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: fix fw path name for WCN3990 targetGovind Singh
FW path is mapped incorrectly for the WCN3990 hw version. Fix fw path with correct hw1.0 name. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add inlined wrappers for htt rx opsErik Stromdahl
Added for the same reason as the TX wrappers. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add inlined wrappers for htt tx opsErik Stromdahl
These wrappers makes the HTT ops align better with the HIF ops (where similar wrappers are used). It also makes it easier for a target to have unsupported ops (by letting the corresponding function pointer be NULL). Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: search all IEs for variant before falling backThomas Hebb
commit f2593cb1b291 ("ath10k: Search SMBIOS for OEM board file extension") added a feature to ath10k that allows Board Data File (BDF) conflicts between multiple devices that use the same device IDs but have different calibration requirements to be resolved by allowing a "variant" string to be stored in SMBIOS [and later device tree, added by commit d06f26c5c8a4 ("ath10k: search DT for qcom,ath10k-calibration- variant")] that gets appended to the ID stored in board-2.bin. This original patch had a regression, however. Namely that devices with a variant present in SMBIOS that didn't need custom BDFs could no longer find the default BDF, which has no variant appended. The patch was reverted and re-applied with a fix for this issue in commit 1657b8f84ed9 ("search SMBIOS for OEM board file extension"). But the fix to fall back to a default BDF introduced another issue: the driver currently parses IEs in board-2.bin one by one, and for each one it first checks to see if it matches the ID with the variant appended. If it doesn't, it checks to see if it matches the "fallback" ID with no variant. If a matching BDF is found at any point during this search, the search is terminated and that BDF is used. The issue is that it's very possible (and is currently the case for board-2.bin files present in the ath10k-firmware repository) for the default BDF to occur in an earlier IE than the variant-specific BDF. In this case, the current code will happily choose the default BDF even though a better-matching BDF is present later in the file. This patch fixes the issue by first searching the entire file for the ID with variant, and searching for the fallback ID only if that search fails. It also includes some code cleanup in the area, as ath10k_core_fetch_board_data_api_n() no longer does its own string mangling to remove the variant from an ID, instead leaving that job to a new flag passed to ath10k_core_create_board_name(). I've tested this patch on a QCA4019 and verified that the driver behaves correctly for 1) both fallback and variant BDFs present, 2) only fallback BDF present, and 3) no matching BDFs present. Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension") Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: fix a typo in ath10k_wmi_set_wmm_param()Maharaja Kennadyrajan
Fix a typo in the function ath10k_wmi_set_wmm_param(). Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: correct target assert problem due to CE5 stuckManikanta Pubbisetty
Correct a minor bug in the commit 0628467f97b5 ("ath10k: fix copy engine 5 destination ring stuck") which introduced a change to fix firmware assert that happens when ring indices of copy engine 5 are stuck for a specific duration, problem with this fix is that it did not use ring arithmatic. As a result,firmware asserts did not go away entirely athough the frequency of occurrence has reduced. Using ring arithmatic to fix the issue. Tested on QCA9984(fw version-10.4-3.4-00082). Fixes: 0628467f97b5 ("ath10k: fix copy engine 5 destination ring stuck) Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: vote for hardware resources for WCN3990Govind Singh
Add clock and regulator votes for WCN3990 WLAN chipset. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: check all CE for data if irq summary is not retainedRakesh Pillai
WCN3990 has interrupts per CE and the interrupt summary is not retained after the interrupt handler has finished execution. We need to check if we received any ce in rx and tx completion path. Generate a interrupt summary with all CE interrupts if the target does not retain interrupt summary after the execution of interrupt handler. Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add support to get target info from hif opsRakesh Pillai
wcn3990 does not use bmi. Add support to get target info from hif ops. Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: modify hif tx paddr to dma_addr_t typeGovind Singh
Change type of hif sg tx paddr to dma_addr_t for supporting target having addressing mode greater than 32 bit. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add hif rx methods for wcn3990Govind Singh
Add hif rx methods in rx path for wcn3990 target. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add hif tx methods for wcn3990Govind Singh
Add hif tx/tx-complete methods for wcn3990 target. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add hif power-up/power-down methodsGovind Singh
Add hif power-up/power-down methods for wcn3990 target. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: map HTC services to tx/rx pipes for wcn3990Govind Singh
Add mapping of HTC endpoint services supported by wcn3990 target to tx/rx pipe. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add HTC services for WCN3990Govind Singh
WCN3990 target uses 3 Copy engine(CE1/CE9/CE10) in RX path and CE 11 for pktlog. Add data path HTC ep services and PKTLOG services for WCN3990. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add hif start/stop methods for wcn3990 snoc layerGovind Singh
Add hif start/stop callback for allocating/freeing buffers on tx/rx pipe and enabling/disabling the tx/rx pipe interrupts. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: add resource init and deinit for WCN3990Govind Singh
Add methods for resource(memory, irq, HOST CE config) initialization and de-initialization for WCN3990 target. WCN3990 target uses 12 copy engine and following CE config. [CE0] :host->target control and raw streams [CE1] :target->host HTT [CE2] :target->host WMI [CE3] :host->target WMI [CE4] :host->target HTT [CE5] :reserved [CE6] :Target autonomous HIF_memcpy [CE7] :reserved [CE8] :reserved [CE9] :target->host HTT [CE10] :target->host HTT [CE11] :target -> host PKTLOG Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: platform driver for WCN3990 SNOC WLAN moduleGovind Singh
WCN3990 is integrated 802.11ac chipset with SNOC bus interface. Add snoc layer driver registration and associated ops. WCN3990 support is not yet complete as cold-boot handshake is done using qmi(Qualcomm-MSM-Interface) and qmi client support will be added once qmi framework is available. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: build ce layer in ath10k core moduleGovind Singh
CE layer is shared between pci and snoc target and results in duplicate object inclusion if both modules are compiled together statically and undefined KBUILD_MODNAME if compiled as module. Fix this by building ce layer in ath10k core module by adding ce object inclusion with ATH10K_CE boolean CONFIG. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-19ath10k: Add tx ack signal support for management framesVenkateswara Naralasetty
This patch add support to get RSSI from acknowledgment frames for transmitted management frames. hardware_used: QCA4019, QCA9984. firmware version: 10.4-3.5.3-00052. Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-10ath10k: fix spelling mistake: "tiggers" -> "triggers"Colin Ian King
Trivial fix to spelling mistake in message text Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-10ath10k: sdio: fix memory leak for probe allocationsMarcus Folkesson
These allocations are not freed upon release. When on it; go for managed resources instead. Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com> [kvalo: fix two checkpatch warnings] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit 1.2.3-korg (git 2.39.0) at 2024-07-01 04:15:12 +0000