| Age | Commit message (Collapse) | Author |
|---|
|
“dev_kfree_skb”
[ Upstream commit 868ad21496020ef83d41fdeed3b0a63de2a3caa5 ]
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stable-dep-of: 0c1528675d7a ("wifi: iwlegacy: common: don't call dev_kfree_skb() under spin_lock_irqsave()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6dfbc3ba90cc2b619229be56b485f085a0a8e1c ]
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1629811733-7927-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c7cee9c0f499f27ec6de06bea664b61320534768 ]
The wmi service available event has been
extended to contain extra 128 bit for new services
to be indicated by firmware.
Currently the presence of any optional TLVs in
the wmi service available event leads to a parsing
error with the below error message:
ath10k_snoc 18800000.wifi: failed to parse svc_avail tlv: -71
The wmi service available event parsing should
not return error for the newly added optional TLV.
Fix this parsing for service available event message.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00720-QCAHLSWMTPL-1
Fixes: cea19a6ce8bf ("ath10k: add WMI_SERVICE_AVAILABLE_EVENT support")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605501291-23040-1-git-send-email-pillair@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5329b2d5b8b4e41be14d31ee8505b4f5607bf9b ]
If firmware reports rate_max > WMI_TPC_RATE_MAX(WMI_TPC_FINAL_RATE_MAX)
or num_tx_chain > WMI_TPC_TX_N_CHAIN, it will cause array out-of-bounds
access, so print a warning and reset to avoid memory corruption.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ba8b3b6bd772f575f7736c8fd893c6981fcce16 ]
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb6 ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Currently instant rx_duration always fetching as zero
in fw_stats debugfs entry if extended peer stats event
supports.
This patch updates instant rx_duration in fw_stats entry
based on extended peer stats and maintaining backward
compatibility for 10.2/10.x.
Tested HW: QCA9984.
Tested FW: 10.4-3.6.0.1-00004.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662ce1
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662ce1 ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
|
|
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02b7 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The host driver currently expects the channel info event to be
received in pairs for all the channels, i.e. the first
chan_info event for a particular channel will not have the
COMPLETE flag set and the second chan_info event for the
same channel will have the COMPLETE flag set.
The HL2.0 firmware sends only one channel info event per channel
which is scanned without the COMPLETE flag set. After sending the
chan_info_event for all the channels, the HL2.0 firmware sends a
chan_info_event with COMPLETE flag set to indicate the completion
of the channel info event.
The firmware does not indicate this behavior with any service bitmap
and hence a new firmware feature flag is used to handle the modified
parsing of the channel info events, in the host driver, for the
firmware which sends single channel info event per scanned channel.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Co-developed-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The tx_status for management frames is being filled
incorrectly in the flags of skb_cb. This incorrect
flag setting causes the upper layers to consider that
the particular frame was not transmitted properly,
leading to improper behavior.
Set the IEEE80211_TX_STAT_ACK flag in the info flags
of skb_cb, to indicate the successful transmission of
the management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: dc405152bb64d4ae01c9ac669de25b2d1fb6fc2d
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is done in order not to trig the below warning in
ieee80211_rx_napi:
WARN_ON_ONCE(softirq_count() == 0);
ieee80211_rx_napi requires that softirq's are disabled during
execution.
The High latency bus drivers (SDIO and USB) sometimes call the wmi
ep_rx_complete callback from non softirq context, resulting in a trigger
of the above warning.
Calling ieee80211_rx_ni with softirq's already disabled (e.g., from
softirq context) should be safe as the local_bh_disable and
local_bh_enable functions (called from ieee80211_rx_ni) are fully
reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
array "ctl_power_table" access index "pream" is initialized with -1 and
is raised as a static analysis tool issue.
[drivers\net\wireless\ath\ath10k\wmi.c:4719] ->
[drivers\net\wireless\ath\ath10k\wmi.c:4730]: (error) Array index -1 is
out of bounds.
Since the "pream" index for accessing ctl_power_table array is initialized
with -1, there is a chance of memory access violation for the cases below.
1) wmi_pdev_tpc_final_table_event change frequency is between 2483 and 5180
2) pream_idx is out of the enumeration ranges of wmi_tpc_pream_2ghz,
wmi_tpc_pream_5ghz
Signed-off-by: K.T.VIJAYAKUMAAR <vijay.bvb@samsung.com>
[kvalo@codeaurora.org: clean up the warning message]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
Wifi).
Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The India regulatory domain allows CH 173, so add that to the
available channel list. I verified basic connectivity between
a 9880 and 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently tpc_stats is allocated and is leaked on the return
path if num_tx_chain is greater than WMI_TPC_TX_N_CHAIN. Avoid
this leak by performing the check on num_tx_chain before the
allocation of tpc_stats.
Detected by CoverityScan, CID#1469422 ("Resource Leak")
Fixes: 4b190675ad06 ("ath10k: fix kernel panic while reading tpc_stats")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation
feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag.
This new features enables the ath10k host to send information to the
firmware on the specifications of detected radar type. This allows the
firmware to validate if the host's radar pattern detector unit is
operational and check if the radar information shared by host matches
the radar pulses sent as phy error events from firmware. If the check
fails the firmware won't allow use of DFS channels on AP mode when using
FCC regulatory region.
Hence this patch is mandatory when using a firmware from 10.4-3.6 branch.
Else, DFS channels on FCC regions cannot be used.
Supported Chipsets : QCA9984/QCA9888/QCA4019
Firmware Version : 10.4-3.6-00104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This enables ath10k/ath9k drivers to collect the specifications of the
radar type once it is detected by the dfs pattern detector unit.
Usage of the collected info is specific to driver implementation.
For example, collected radar info could be used by the host driver
to send to co-processors for additional processing/validation.
Note: 'radar_detector_specs' data containing the specifications of
different radar types which was private within dfs_pattern_detector/
dfs_pri_detector is now shared with drivers as well for making use
of this information.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variable buf_len and num_vdev_stats are being assigned but never read.
These are redundant and can be remove.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Trivial fix to spelling mistake in ath10k_warn warning message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When attempt to read tpc_stats for the chipsets which support
more than 3 tx chain will trigger kernel panic(kernel stack is corrupted)
due to writing values on rate_code array out of range.
This patch changes the array size depends on the WMI_TPC_TX_N_CHAIN and
added check to avoid write values on the array if the num tx chain
get in tpc config event is greater than WMI_TPC_TX_N_CHAIN.
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00057
Kernel panic log :
[ 323.510944] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: bf90c654
[ 323.510944]
[ 323.524390] CPU: 0 PID: 1908 Comm: cat Not tainted 3.14.77 #31
[ 323.530224] [<c021db48>] (unwind_backtrace) from [<c021ac08>] (show_stack+0x10/0x14)
[ 323.537941] [<c021ac08>] (show_stack) from [<c03c53c0>] (dump_stack+0x80/0xa0)
[ 323.545146] [<c03c53c0>] (dump_stack) from [<c022e4ac>] (panic+0x84/0x1e4)
[ 323.552000] [<c022e4ac>] (panic) from [<c022e61c>] (__stack_chk_fail+0x10/0x14)
[ 323.559350] [<c022e61c>] (__stack_chk_fail) from [<bf90c654>] (ath10k_wmi_event_pdev_tpc_config+0x424/0x438 [ath10k_core])
[ 323.570471] [<bf90c654>] (ath10k_wmi_event_pdev_tpc_config [ath10k_core]) from [<bf90d800>] (ath10k_wmi_10_4_op_rx+0x2f0/0x39c [ath10k_core])
[ 323.583047] [<bf90d800>] (ath10k_wmi_10_4_op_rx [ath10k_core]) from [<bf8fcc18>] (ath10k_htc_rx_completion_handler+0x170/0x1a0 [ath10k_core])
[ 323.595702] [<bf8fcc18>] (ath10k_htc_rx_completion_handler [ath10k_core]) from [<bf961f44>] (ath10k_pci_hif_send_complete_check+0x1f0/0x220 [ath10k_pci])
[ 323.609421] [<bf961f44>] (ath10k_pci_hif_send_complete_check [ath10k_pci]) from [<bf96562c>] (ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci])
[ 323.622490] [<bf96562c>] (ath10k_ce_per_engine_service [ath10k_pci]) from [<bf9656f0>] (ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci])
[ 323.635423] [<bf9656f0>] (ath10k_ce_per_engine_service_any [ath10k_pci]) from [<bf96365c>] (ath10k_pci_napi_poll+0x44/0xe8 [ath10k_pci])
[ 323.647665] [<bf96365c>] (ath10k_pci_napi_poll [ath10k_pci]) from [<c0599994>] (net_rx_action+0xac/0x160)
[ 323.657208] [<c0599994>] (net_rx_action) from [<c02324a4>] (__do_softirq+0x104/0x294)
[ 323.665017] [<c02324a4>] (__do_softirq) from [<c0232920>] (irq_exit+0x9c/0x11c)
[ 323.672314] [<c0232920>] (irq_exit) from [<c0217fc0>] (handle_IRQ+0x6c/0x90)
[ 323.679341] [<c0217fc0>] (handle_IRQ) from [<c02084e0>] (gic_handle_irq+0x3c/0x60)
[ 323.686893] [<c02084e0>] (gic_handle_irq) from [<c02095c0>] (__irq_svc+0x40/0x70)
[ 323.694349] Exception stack(0xdd489c58 to 0xdd489ca0)
[ 323.699384] 9c40: 00000000 a0000013
[ 323.707547] 9c60: 00000000 dc4bce40 60000013 ddc1d800 dd488000 00000990 00000000 c085c800
[ 323.715707] 9c80: 00000000 dd489d44 0000092d dd489ca0 c026e664 c026e668 60000013 ffffffff
[ 323.723877] [<c02095c0>] (__irq_svc) from [<c026e668>] (rcu_note_context_switch+0x170/0x184)
[ 323.732298] [<c026e668>] (rcu_note_context_switch) from [<c020e928>] (__schedule+0x50/0x4d4)
[ 323.740716] [<c020e928>] (__schedule) from [<c020e490>] (schedule_timeout+0x148/0x178)
[ 323.748611] [<c020e490>] (schedule_timeout) from [<c020f804>] (wait_for_common+0x114/0x154)
[ 323.756972] [<c020f804>] (wait_for_common) from [<bf8f6ef0>] (ath10k_tpc_stats_open+0xc8/0x340 [ath10k_core])
[ 323.766873] [<bf8f6ef0>] (ath10k_tpc_stats_open [ath10k_core]) from [<c02bb598>] (do_dentry_open+0x1ac/0x274)
[ 323.776741] [<c02bb598>] (do_dentry_open) from [<c02c838c>] (do_last+0x8c0/0xb08)
[ 323.784201] [<c02c838c>] (do_last) from [<c02c87e4>] (path_openat+0x210/0x598)
[ 323.791408] [<c02c87e4>] (path_openat) from [<c02c9d1c>] (do_filp_open+0x2c/0x78)
[ 323.798873] [<c02c9d1c>] (do_filp_open) from [<c02bc85c>] (do_sys_open+0x114/0x1b4)
[ 323.806509] [<c02bc85c>] (do_sys_open) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
[ 323.814241] CPU1: stopping
[ 323.816927] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.77 #31
[ 323.823008] [<c021db48>] (unwind_backtrace) from [<c021ac08>] (show_stack+0x10/0x14)
[ 323.830731] [<c021ac08>] (show_stack) from [<c03c53c0>] (dump_stack+0x80/0xa0)
[ 323.837934] [<c03c53c0>] (dump_stack) from [<c021cfac>] (handle_IPI+0xb8/0x140)
[ 323.845224] [<c021cfac>] (handle_IPI) from [<c02084fc>] (gic_handle_irq+0x58/0x60)
[ 323.852774] [<c02084fc>] (gic_handle_irq) from [<c02095c0>] (__irq_svc+0x40/0x70)
[ 323.860233] Exception stack(0xdd499fa0 to 0xdd499fe8)
[ 323.865273] 9fa0: ffffffed 00000000 1d3c9000 00000000 dd498000 dd498030 10c0387d c08b62c8
[ 323.873432] 9fc0: 4220406a 512f04d0 00000000 00000000 00000001 dd499fe8 c021838c c0218390
[ 323.881588] 9fe0: 60000013 ffffffff
[ 323.885070] [<c02095c0>] (__irq_svc) from [<c0218390>] (arch_cpu_idle+0x30/0x50)
[ 323.892454] [<c0218390>] (arch_cpu_idle) from [<c026500c>] (cpu_startup_entry+0xa4/0x108)
[ 323.900690] [<c026500c>] (cpu_startup_entry) from [<422085a4>] (0x422085a4)
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix a typo in the function ath10k_wmi_set_wmm_param().
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The way that 'strncat' is used here raised a warning in gcc-8:
drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables':
drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Effectively, this is simply a strcat() but the use of strncat() suggests
some form of overflow check. Regardless of whether this might actually
overflow, using strlcat() instead of strncat() avoids the warning and
makes the code more robust.
Fixes: bc64d05220f3 ("ath10k: debugfs support to get final TPC stats for 10.4 variants")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The skb may be freed in tx completion context before
trace_ath10k_wmi_cmd is called. This can be easily captured when
KASAN(Kernel Address Sanitizer) is enabled. The fix is to move
trace_ath10k_wmi_cmd before the send operation. As the ret has no
meaning in trace_ath10k_wmi_cmd then, so remove this parameter too.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Update year for Qualcomm Atheros, Inc. copyrights.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Handle tdls peer events from the target. TDLS events for the peer
could be discover, teardown, etc. As of now, adding the logic to
handle tdls teardown events alone.
Teardown due to peer traffic indication(PTR) timeout is one such
teardown event from the target.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The current firmware 10.4-3.5.1-00035 on QCA9888 supports
TDLS explicit mode, it expects WMI_TDLS_ENABLE_PASSIVE
for tdls setup and WMI_TDLS_DISABLE for tdls teardown.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
Markus Elfring
Loic Poulain
Rakesh Pillai
Miaoqing Pan
Balaji Pothunoori
Surabhi Vishnoi
Abhishek Ambure
Kalle Valo
Pradeep Kumar Chitrapu
Christian Lamparter
Luis Chamberlain
Bhagavathi Perumal S
Dan Carpenter
Sathishkumar Muruganandam
Maharaja Kennadyrajan
Ben Greear
Erik Stromdahl
K.T.VIJAYAKUMAAR
Brian Norris
Martin Willi
YueHaibing
Colin Ian King
Sriram R
Kenneth Lu
Tamizh Chelvam
Carl Huang
Arnd Bergmann
Rajkumar Manoharan
Kalle Valo
Manikanta Pubbisetty
Anilkumar Kolli