| Age | Commit message (Collapse) | Author |
|---|
|
|
|
[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]
Following a similar reinstate for the KSZ8081 and KSZ9031.
Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.
The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit 32fa4366cc4da1c97b725a0066adf43c6b298f37 ]
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec732951702 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8a5c731fd1223090af57da33838c671a7fc6a78 ]
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay")
Signed-off-by: Tim Pambor <tp@osasysteme.de>
Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 621427fbdada788f18f77238e1c36f463c2cb9d1 ]
RGMII mode can be enable from dp83822 straps, and also writing bit 9
of register 0x17 - RMII and Status Register (RCSR).
When phy_interface_is_rgmii rgmii mode must be enabled, same for
contrary, this prevents malconfigurations of hw straps
References:
- https://www.ti.com/lit/gpn/dp83822i p66
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Alberto Bianchi <alberto.bianchi@amarulasolutions.com>
Tested-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c8a5c731fd12 ("net: phy: dp83822: Fix RGMII TX delay configuration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4469c0c5b14a0919f5965c7ceac96b523eb57b79 ]
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/acpi/acpi_lpss.c
# drivers/mfd/intel-lpss.c
# drivers/usb/phy/phy-mxs-usb.c
|
|
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit 766607570becbd26cab6d66a544dd8d0d964df5a ]
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: aef05e349bfd ("net: usb: ax88179_178a: avoid failed operations when device is disconnected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
# drivers/clk/imx/clk-imx8mq.c
|
|
commit 02d5fdbf4f2b8c406f7a4c98fa52aa181a11d733 upstream.
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
[ Upstream commit e0a8c918daa58700609ebd45e3fcd49965be8bbc ]
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa904 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/tty/serial/fsl_lpuart.c
|
|
[ Upstream commit 096516d092d54604d590827d05b1022c8f326639 ]
The 54810 does not support c45. The mmd_phy_indirect accesses return
arbirtary values leading to odd behavior like saying it supports EEE
when it doesn't. We also see that reading/writing these non-existent
MMD registers leads to phy instability in some cases.
Fixes: b14995ac2527 ("net: phy: broadcom: Add BCM54810 PHY entry")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1691901708-28650-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc941e548bffc01b5816b4edc5cb432a137a58b3 ]
Uwe reports:
"Most PHYs signal WoL using an interrupt. So disabling interrupts [at
shutdown] breaks WoL at least on PHYs covered by the marvell driver."
Discussing with Ioana, the problem which was trying to be solved was:
"The board in question is a LS1021ATSN which has two AR8031 PHYs that
share an interrupt line. In case only one of the PHYs is probed and
there are pending interrupts on the PHY#2 an IRQ storm will happen
since there is no entity to clear the interrupt from PHY#2's registers.
PHY#1's driver will get stuck in .handle_interrupt() indefinitely."
Further confirmation that "the two AR8031 PHYs are on the same MDIO
bus."
With WoL using interrupts to wake the system, in such a case, the
system will begin booting with an asserted interrupt. Thus, we need to
cope with an interrupt asserted during boot.
Solve this instead by disabling interrupts during PHY probe. This will
ensure in Ioana's situation that both PHYs of the same type sharing an
interrupt line on a common MDIO bus will have their interrupt outputs
disabled when the driver probes the device, but before we hook in any
interrupt handlers - thus avoiding the interrupt storm.
A better fix would be for platform firmware to disable the interrupting
devices at source during boot, before control is handed to the kernel.
Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure")
Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
commit d7791cec2304aea22eb2ada944e4d467302f5bfe upstream.
Since the AR8032 part does not support wol, remove related callbacks
from it.
Fixes: 5800091a2061 ("net: phy: at803x: add support for AR8032 PHY")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/usb/dwc3/core.h
|
|
[ Upstream commit c7b75bea853daeb64fc831dbf39a6bbabcc402ac ]
Clear MV_V2_PORT_CTRL_PWRDOWN bit to set power up for 88x3310 PHY,
it sometimes does not take effect immediately. And a read of this
register causes the bit not to clear. This will cause mv3310_reset()
to time out, which will fail the config initialization. So add a delay
before the next access.
Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit 1c613beaf877c0c0d755853dc62687e2013e55c4 ]
mdio_bus_init() and phy_driver_register() both have error paths, and if
those are ever hit, ethtool will have a stale pointer to the
phy_ethtool_phy_ops stub structure, which references memory from a
module that failed to load (phylib).
It is probably hard to force an error in this code path even manually,
but the error teardown path of phy_init() should be the same as
phy_exit(), which is now simply not the case.
Fixes: 55d8f053ce1b ("net: phy: Register ethtool PHY operations")
Link: https://lore.kernel.org/netdev/ZLaiJ4G6TaJYGJyU@shell.armlinux.org.uk/
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230720000231.1939689-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/spi/spi-fsl-lpspi.c
|
|
[ Upstream commit a129b41fe0a8b4da828c46b10f5244ca07a3fec3 ]
This reverts commit da9ef50f545f86ffe6ff786174d26500c4db737a.
This fixes a regression in which the link would come up, but no
communication was possible.
The reverted commit was also removing a comment about
DP83867_PHYCR_FORCE_LINK_GOOD, this is not added back in this commits
since it seems that this is unrelated to the original code change.
Closes: https://lore.kernel.org/all/ZGuDJos8D7N0J6Z2@francesco-nb.int.toradex.com/
Fixes: da9ef50f545f ("net: phy: dp83867: perform soft reset and retain established link")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20230619154435.355485-1-francesco@dolcini.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
[ Upstream commit 71460c9ec5c743e9ffffca3c874d66267c36345e ]
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/regulator/pca9450-regulator.c
# drivers/usb/dwc3/core.h
|
|
commit 57fb54ab9f6945e204740b696bd4cee61ee04e5e upstream.
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# sound/soc/fsl/fsl_micfil.c
|
|
[ Upstream commit 0b01db274028f5acd207332686ffc92ac77491ac ]
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
write_reg(0x001F, 0x8000); //hard reset
write_reg(DSP_FFE_CFG, 0x0E81);
write_reg(0x001F, 0x4000); //soft reset
Since DP83867 PHY DM says "Changing this register to 0x0E81, will not
affect Long Cable performance.", enable the W/A by default.
Fixes: 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/i2c/busses/i2c-imx-lpi2c.c
|
|
commit bdaaecc127d471c422ee9e994978617c8aa79e1e upstream.
Any multiplication between GENMASK(31, 0) and a number bigger than 1
will be truncated because of the overflow, if the size of unsigned long
is 32 bits.
Replaced GENMASK with GENMASK_ULL to make sure that multiplication will
be between 64 bits values.
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095953.75622-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4506722dc39ca840593f14e3faa4c9ba9408211 upstream.
Unregister PTP clock when the driver is removed.
Purge the RX and TX skb queues.
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095904.75456-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 813c2dd78618f108fdcf9cd726ea90f081ee2881 upstream.
sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.
One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.
# ethtool -m xge0
i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
Cannot get Module EEPROM data: Operation not supported
If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error
# ethtool -m xge0
Cannot get Module EEPROM data: Remote I/O error
Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# drivers/tty/serial/fsl_lpuart.c
# drivers/usb/chipidea/ci.h
# drivers/usb/chipidea/core.c
|
|
commit 82e2c39f9ef78896e9b634dfd82dc042e6956bb7 upstream.
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Cc: stable@vger.kernel.org
Fixes: 736b25afe284 ("net: dp83869: Add RGMII internal delay configuration")
Co-developed-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323102536.31988-1-josua@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 99669259f3361d759219811e670b7e0742668556 ]
Bus ownership is wrong when using of_mdiobus_register() to register an mdio
bus. That function is not inline, so when it calls mdiobus_register() the wrong
THIS_MODULE value is captured.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
[florian: fix kdoc, added Fixes tag]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4203d84032e28f893594a453bd8bc9c3b15c7334 ]
In the phy_disconnect() -> phy_stop() path, we will be forcibly setting
the PHY state machine to PHY_HALTED. This invalidates the old_state !=
phydev->state condition in phy_state_machine() such that we will neither
display the state change for debugging, nor will we invoke the
link_change_notify() callback.
Factor the code by introducing phy_process_state_change(), and ensure
that we process the state change from phy_stop() as well.
Fixes: 5c5f626bcace ("net: phy: improve handling link_change_notify callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
commit 8ba572052a4b8fe5b205854d27e54e3486049b71 upstream.
According to the TJA1103 user manual, the bit for the reversed role in MII
or RMII modes is bit 4.
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: b050f2f15e04 ("phy: nxp-c45: add driver for tja1103")
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230309100111.1246214-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c22c3bbf351e4ce905f082649cffa1ff893ea8c1 ]
If genphy_read_status fails then further access to the PHY may result
in unpredictable behavior. To prevent this bail out immediately if
genphy_read_status fails.
Fixes: 4223dbffed9f ("net: phy: smsc: Re-enable EDPD mode for LAN87xx")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/026aa4f2-36f5-1c10-ab9f-cdb17dda6ac4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# arch/arm/mach-imx/mmdc.c
# drivers/media/platform/imx-jpeg/mxc-jpeg.c
# drivers/tty/serial/fsl_lpuart.c
# sound/soc/fsl/fsl_sai.c
# sound/soc/fsl/fsl_sai.h
|
|
[ Upstream commit 58aac3a2ef414fea6d7fdf823ea177744a087d13 ]
Currently link up can't be detected in forced mode if polling
isn't used. Only link up interrupt source we have is aneg
complete which isn't applicable in forced mode. Therefore we
have to use energy-on as link up indicator.
Fixes: 7365494550f6 ("net: phy: smsc: skip ENERGYON interrupt if disabled")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7e8b617eb93f9fcaedac02cd19edcad31c767386 ]
Cache the interrupt mask to avoid re-reading it from the PHY upon every
interrupt.
This will simplify a subsequent commit which detects hot-removal in the
interrupt handler and bails out.
Analyzing and debugging PHY transactions also becomes simpler if such
redundant reads are avoided.
Last not least, interrupt overhead and latency is slightly improved.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 58aac3a2ef41 ("net: phy: smsc: fix link up detection in forced irq mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f4b47a2e9463950df3e7c8b70e017877c1d4eb11 ]
The locking in phy_probe() and phy_remove() does very little to prevent
any races with e.g. phy_attach_direct(), but instead causes lockdep ABBA
warnings. Remove it.
======================================================
WARNING: possible circular locking dependency detected
6.2.0-dirty #1108 Tainted: G W E
------------------------------------------------------
ip/415 is trying to acquire lock:
ffff5c268f81ef50 (&dev->lock){+.+.}-{3:3}, at: phy_attach_direct+0x17c/0x3a0 [libphy]
but task is already holding lock:
ffffaef6496cb518 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x154/0x560
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.}-{3:3}:
__lock_acquire+0x35c/0x6c0
lock_acquire.part.0+0xcc/0x220
lock_acquire+0x68/0x84
__mutex_lock+0x8c/0x414
mutex_lock_nested+0x34/0x40
rtnl_lock+0x24/0x30
sfp_bus_add_upstream+0x34/0x150
phy_sfp_probe+0x4c/0x94 [libphy]
mv3310_probe+0x148/0x184 [marvell10g]
phy_probe+0x8c/0x200 [libphy]
call_driver_probe+0xbc/0x15c
really_probe+0xc0/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__device_attach_driver+0xc4/0x160
bus_for_each_drv+0x80/0xe0
__device_attach+0xb0/0x1f0
device_initial_probe+0x1c/0x2c
bus_probe_device+0xa4/0xb0
device_add+0x360/0x53c
phy_device_register+0x60/0xa4 [libphy]
fwnode_mdiobus_phy_device_register+0xc0/0x190 [fwnode_mdio]
fwnode_mdiobus_register_phy+0x160/0xd80 [fwnode_mdio]
of_mdiobus_register+0x140/0x340 [of_mdio]
orion_mdio_probe+0x298/0x3c0 [mvmdio]
platform_probe+0x70/0xe0
call_driver_probe+0x34/0x15c
really_probe+0xc0/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0x104/0x210
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x3c
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__platform_driver_register+0x30/0x3c
xt_compat_calc_jump+0x28/0xa4 [x_tables]
do_one_initcall+0x50/0x1b0
do_init_module+0x50/0x1fc
load_module+0x684/0x744
__do_sys_finit_module+0xc4/0x140
__arm64_sys_finit_module+0x28/0x34
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0x6c/0x1b0
do_el0_svc+0x34/0x44
el0_svc+0x48/0xf0
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x1a0/0x1a4
-> #0 (&dev->lock){+.+.}-{3:3}:
check_prev_add+0xb4/0xc80
validate_chain+0x414/0x47c
__lock_acquire+0x35c/0x6c0
lock_acquire.part.0+0xcc/0x220
lock_acquire+0x68/0x84
__mutex_lock+0x8c/0x414
mutex_lock_nested+0x34/0x40
phy_attach_direct+0x17c/0x3a0 [libphy]
phylink_fwnode_phy_connect.part.0+0x70/0xe4 [phylink]
phylink_fwnode_phy_connect+0x48/0x60 [phylink]
mvpp2_open+0xec/0x2e0 [mvpp2]
__dev_open+0x104/0x214
__dev_change_flags+0x1d4/0x254
dev_change_flags+0x2c/0x7c
do_setlink+0x254/0xa50
__rtnl_newlink+0x430/0x514
rtnl_newlink+0x58/0x8c
rtnetlink_rcv_msg+0x17c/0x560
netlink_rcv_skb+0x64/0x150
rtnetlink_rcv+0x20/0x30
netlink_unicast+0x1d4/0x2b4
netlink_sendmsg+0x1a4/0x400
____sys_sendmsg+0x228/0x290
___sys_sendmsg+0x88/0xec
__sys_sendmsg+0x70/0xd0
__arm64_sys_sendmsg+0x2c/0x40
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0x6c/0x1b0
do_el0_svc+0x34/0x44
el0_svc+0x48/0xf0
el0t_64_sync_handler+0xb8/0xc0
el0t_64_sync+0x1a0/0x1a4
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(rtnl_mutex);
lock(&dev->lock);
lock(rtnl_mutex);
lock(&dev->lock);
*** DEADLOCK ***
Fixes: 298e54fa810e ("net: phy: add core phylib sfp support")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
from the MAC driver
[ Upstream commit e57cf3639c323eeed05d3725fd82f91b349adca8 ]
Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).
Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."
I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.
Fixes: 14437e3fa284 ("lan78xx: workaround of forced 100 Full/Half duplex mode error")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
# Conflicts:
# arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
# drivers/iio/imu/fxos8700_core.c
|
Bruce Ashfield
Mathieu Othacehe
Nikita Kiryushin
Tim Pambor
Tommaso Merciai
Kévin L'hôpital
Claudiu Beznea
Jakub Kicinski
Klaus Kudielka
Radu Pirea (NXP OSS)
Justin Chen
Russell King (Oracle)
Li Yang
Jiawen Wu
Vladimir Oltean
Francesco Dolcini
David Epping
Grygorii Strashko
Ivan Bornyakov
Josua Mayer
Maxime Bizon
Florian Fainelli
Heiner Kallweit
Lukas Wunner
Yuiko Oshino