Age | Commit message (Collapse) | Author |
|
[ Upstream commit fd8d9731bcdfb22d28e45bce789bcb211c868c78 ]
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ]
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 10eff1f5788b6ffac212c254e2f3666219576889 upstream.
This reverts commit ab609f25d19858513919369ff3d9a63c02cd9e2e.
This patch is correct in the sense that we _should_ call device_put() in
case of device_register() failure, but the problem in this code is more
vast.
We need to set bus->state to UNMDIOBUS_REGISTERED before calling
device_register() to correctly release the device in mdiobus_free().
This patch prevents us from doing it, since in case of device_register()
failure put_device() will be called 2 times and it will cause UAF or
something else.
Also, Reported-by: tag in revered commit was wrong, since syzbot
reported different leak in same function.
Link: https://lore.kernel.org/netdev/20210928092657.GI2048@kadam/
Acked-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/f12fb1faa4eccf0f355788225335eb4309ff2599.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab609f25d19858513919369ff3d9a63c02cd9e2e upstream.
Once device_register() failed, we should call put_device() to
decrement reference count for cleanup. Or it will cause memory
leak.
BUG: memory leak
unreferenced object 0xffff888114032e00 (size 256):
comm "kworker/1:3", pid 2960, jiffies 4294943572 (age 15.920s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 08 2e 03 14 81 88 ff ff ................
08 2e 03 14 81 88 ff ff 90 76 65 82 ff ff ff ff .........ve.....
backtrace:
[<ffffffff8265cfab>] kmalloc include/linux/slab.h:591 [inline]
[<ffffffff8265cfab>] kzalloc include/linux/slab.h:721 [inline]
[<ffffffff8265cfab>] device_private_init drivers/base/core.c:3203 [inline]
[<ffffffff8265cfab>] device_add+0x89b/0xdf0 drivers/base/core.c:3253
[<ffffffff828dd643>] __mdiobus_register+0xc3/0x450 drivers/net/phy/mdio_bus.c:537
[<ffffffff828cb835>] __devm_mdiobus_register+0x75/0xf0 drivers/net/phy/mdio_devres.c:87
[<ffffffff82b92a00>] ax88772_init_mdio drivers/net/usb/asix_devices.c:676 [inline]
[<ffffffff82b92a00>] ax88772_bind+0x330/0x480 drivers/net/usb/asix_devices.c:786
[<ffffffff82baa33f>] usbnet_probe+0x3ff/0xdf0 drivers/net/usb/usbnet.c:1745
[<ffffffff82c36e17>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff82661d17>] call_driver_probe drivers/base/dd.c:517 [inline]
[<ffffffff82661d17>] really_probe.part.0+0xe7/0x380 drivers/base/dd.c:596
[<ffffffff826620bc>] really_probe drivers/base/dd.c:558 [inline]
[<ffffffff826620bc>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:751
[<ffffffff826621ba>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:781
[<ffffffff82662a26>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:898
[<ffffffff8265eca7>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff826625a2>] __device_attach+0x122/0x260 drivers/base/dd.c:969
[<ffffffff82660916>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487
[<ffffffff8265cd0b>] device_add+0x5fb/0xdf0 drivers/base/core.c:3359
[<ffffffff82c343b9>] usb_set_configuration+0x9d9/0xb90 drivers/usb/core/message.c:2170
[<ffffffff82c4473c>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
BUG: memory leak
unreferenced object 0xffff888116f06900 (size 32):
comm "kworker/0:2", pid 2670, jiffies 4294944448 (age 7.160s)
hex dump (first 32 bytes):
75 73 62 2d 30 30 31 3a 30 30 33 00 00 00 00 00 usb-001:003.....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff81484516>] kstrdup+0x36/0x70 mm/util.c:60
[<ffffffff814845a3>] kstrdup_const+0x53/0x80 mm/util.c:83
[<ffffffff82296ba2>] kvasprintf_const+0xc2/0x110 lib/kasprintf.c:48
[<ffffffff82358d4b>] kobject_set_name_vargs+0x3b/0xe0 lib/kobject.c:289
[<ffffffff826575f3>] dev_set_name+0x63/0x90 drivers/base/core.c:3147
[<ffffffff828dd63b>] __mdiobus_register+0xbb/0x450 drivers/net/phy/mdio_bus.c:535
[<ffffffff828cb835>] __devm_mdiobus_register+0x75/0xf0 drivers/net/phy/mdio_devres.c:87
[<ffffffff82b92a00>] ax88772_init_mdio drivers/net/usb/asix_devices.c:676 [inline]
[<ffffffff82b92a00>] ax88772_bind+0x330/0x480 drivers/net/usb/asix_devices.c:786
[<ffffffff82baa33f>] usbnet_probe+0x3ff/0xdf0 drivers/net/usb/usbnet.c:1745
[<ffffffff82c36e17>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff82661d17>] call_driver_probe drivers/base/dd.c:517 [inline]
[<ffffffff82661d17>] really_probe.part.0+0xe7/0x380 drivers/base/dd.c:596
[<ffffffff826620bc>] really_probe drivers/base/dd.c:558 [inline]
[<ffffffff826620bc>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:751
[<ffffffff826621ba>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:781
[<ffffffff82662a26>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:898
[<ffffffff8265eca7>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff826625a2>] __device_attach+0x122/0x260 drivers/base/dd.c:969
Reported-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com
Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d88fd1b546ff19c8040cfaea76bf16aed1c5a0bb upstream.
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a6998 ("net: phy: bcm7xxx: add support for 28nm EPHY")
[florian: adjust locking since phy_{read,write}_mmd are called with no
PHYLIB locks held]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca6e11c337daf7925ff8a2aac8e84490a8691905 ]
Syzbot reported memory leak in MDIO bus interface, the problem was in
wrong state logic.
MDIOBUS_ALLOCATED indicates 2 states:
1. Bus is only allocated
2. Bus allocated and __mdiobus_register() fails, but
device_register() was called
In case of device_register() has been called we should call put_device()
to correctly free the memory allocated for this device, but mdiobus_free()
calls just kfree(dev) in case of MDIOBUS_ALLOCATED state
To avoid this behaviour we need to set bus->state to MDIOBUS_UNREGISTERED
_before_ calling device_register(), because put_device() should be
called even in case of device_register() failure.
Link: https://lore.kernel.org/netdev/YVMRWNDZDUOvQjHL@shell.armlinux.org.uk/
Fixes: 46abc02175b3 ("phylib: give mdio buses a device tree presence")
Reported-and-tested-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/eceae1429fbf8fa5c73dd2a0d39d525aa905074d.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf9579976f724ad517cc15b7caadea728c7e245c ]
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726e9 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7366c23ff492ad260776a3ee1aaabba9fc773a8b upstream.
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7bd0cef5dac685f09ef8b0b2a7748ff42d284dc7 ]
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99d81e942474cc7677d12f673f42a7ea699e2589 ]
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1dde47a66d4fb181830d6fa000e5ea86907b639e ]
We spotted a bug recently during a review where a driver was
unregistering a bus that wasn't registered, which would trigger this
BUG_ON(). Let's handle that situation more gracefully, and just print
a warning and return.
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e1d027dd97e1e750669cdc0d3b016a4f54e473eb ]
'bus->mii_bus' has been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the error handling path of the
probe function and in remove function.
Suggested-By: Andrew Lunn <andrew@lunn.ch>
Fixes: 35d2aeac9810 ("phy: mdio-octeon: Use devm_mdiobus_alloc_size()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a93a0a15876d2a077a3bc260b387d2457a051f24 ]
'bus->mii_bus' have been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the remove function.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c056d480b40a68f2520ccc156c7fae672d69d57d upstream
We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.
Fixes: 99cec8a4dda2 ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d9032dba5a2b2bbf0fdce67c8795300ec9923b43 ]
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846eab ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9621618130bf7e83635367c13b9a6ee53935bb37 ]
gpiod_to_irq() never return 0, but returns negative in
case of error, check it and set gpio_irq to 0.
Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201031031053.25264-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7dbbcf496f2a4b6d82cfc7810a0746e160b79762 ]
Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER.
Fixes this build error:
ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe':
drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size'
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: netdev@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2b727df7caa33876e7066bde090f40001b6d643 ]
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 297a6961ffb8ff4dc66c9fbf53b924bd1dda05d5 ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 473309fb8372365ad211f425bca760af800e10a7 ]
From Documentation/networking/timestamping.txt:
A driver which supports hardware time stamping shall update the
struct with the actual, possibly more permissive configuration.
Do update the struct passed when we upscale the requested time
stamping mode.
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9de5d235b60a7cdfcdd5461e70c5663e713fde87 ]
phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.
Fixes: f75abeb8338e ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 55f53567afe5f0cd2fd9e006b174c08c31c466f8 upstream.
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 865308373ed49c9fb05720d14cbf1315349b32a9 ]
In this code, it appears that phyter_clocks is a list head, based on
the previous list_for_each, and that clock->list is intended to be a
list element, given that it has just been initialized in
dp83640_clock_init. Accordingly, switch the arguments to
list_add_tail, which takes the list head as the second argument.
Fixes: cb646e2b02b27 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
accessing PHY registers
[ Upstream commit 6110dff776f7fa65c35850ef65b41d3b39e2fac2 ]
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 611d779af7cad2b87487ff58e4931a90c20b113c ]
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 503ba7c6961034ff0047707685644cad9287c226 upstream.
It is currently possible for a PHY device to be suspended as part of a
network device driver's suspend call while it is still being attached to
that net_device, either via phy_suspend() or implicitly via phy_stop().
Later on, when the MDIO bus controller get suspended, we would attempt
to suspend again the PHY because it is still attached to a network
device.
This is both a waste of time and creates an opportunity for improper
clock/power management bugs to creep in.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b566f70e1bf65b189b66eb3de6f431c30f7dff2 upstream.
This reverts:
ef1b5bf506b1 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b81296 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
[just take the ef1b5bf506b1 revert - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f08e98d62799e53c89dbf2c9a49d77e20ca648c upstream.
The mii management register in iproc mdio block
does not have a retention register so it is lost on suspend.
Save and restore value of register while resuming from suspend.
Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8f289805616e81f7c1690931aa8a586c76f4fa88 ]
Fix fixed_phy not checking GPIO if no link_update callback
is registered.
In the original version all users registered a link_update
callback so the issue was masked.
Fixes: a5597008dbc2 ("phy: fixed_phy: Add gpio to determine link up/down.")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef1b5bf506b1f0ee3edc98533e1f3ecb105eb46a ]
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a5d66f810061e2dd70fb7a108dcd14e535bc639f ]
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a7f08c2abb0efc9d17aff2fc75d6d3b85e622e4 ]
The link detection timeouts can be observed (or link might not be detected
at all) when dp83867 PHY is configured in manual mode (speed/duplex).
CFG3[9] Robust Auto-MDIX option allows to significantly improve link detection
in case dp83867 is configured in manual mode and reduce link detection
time.
As per DM: "If link partners are configured to operational modes that are
not supported by normal Auto MDI/MDIX mode (like Auto-Neg versus Force
100Base-TX or Force 100Base-TX versus Force 100Base-TX), this Robust Auto
MDI/MDIX mode allows MDI/MDIX resolution and prevents deadlock."
Hence, enable this option by default as there are no known reasons
not to do so.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1a97a477e666cbdededab93bd3754e508f0c09d7 upstream.
After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ adapted for kernels without phy_modify_mmd ]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 333061b924539c0de081339643f45514f5f1c1e6 upstream.
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ adapted for kernels without phy_modify_mmd ]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9b97123a584f60a5bca5a2663485768a1f6cd0a4 ]
The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:
drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
static int unimac_mdio_suspend(struct device *d)
Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.
Fixes: b78ac6ecd1b6 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b78ac6ecd1b6b46f8767cbafa95a7b0b51b87ad8 ]
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36c53cf0f46526b898390659b125155939f67892 ]
In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown'
is an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,edge-slowdown' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a993e0f583c7925adaa7721226ccd7a41e7e63d1 ]
In the DT binding, it is specified nowhere that 'vsc8531,vddmac' is an
u16, even though it's read as an u16 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,vddmac' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e47488b2df7f9cb405789c7f5d4c27909fc597ae ]
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf129856 ("phy: Add file missed in previous commit.")
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 63b2ed4e10b2e6c913e1d8cdd728e7fba4115a3d ]
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reported-by: Shaul Ben-Mayor <shaulb@marvell.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8aace4f3eba2a3ceb431e18683ea0e1ecbade5cd ]
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ]
sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8a17eefa235f73b60c0ca7d397d2e4f66f85f413 upstream.
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 820ee17b8d3b ("net: phy: broadcom: Add support code for reading PHY counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b892649254fec01678c64f16427622b41fa27f4 ]
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28e74a7cfd6403f0d1c0f8b10b45d6fae37b227e ]
Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time. This behaviour is not specified
in the SFP MSAs, which specifies:
"The serial interface uses the 2-wire serial CMOS E2PROM protocol
defined for the ATMEL AT24C01A/02/04 family of components."
and
"As long as the SFP+ receives an acknowledge, it shall serially clock
out sequential data words. The sequence is terminated when the host
responds with a NACK and a STOP instead of an acknowledge."
We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3d3ced2ec5d71b99d72ae6910fbdf890bc2eccf0 ]
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2f23a2a768bee7ad2ff1e9527c3f7e279e794a46 ]
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fdfdf86720a34527f777cbe0d8599bf0528fa146 ]
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a40 ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit c4ba68b8691e4 backported from upstream to 4.14 stable was
probably applied wrongly, and instead of calling sfp_register_socket in
sfp_probe, the socket registering code was put into sfp_remove. This is
obviously wrong.
The commit first appeared in 4.14.104. Fix it for the next 4.14 release.
Fixes: c4ba68b8691e4 ("net: sfp: do not probe SFP module before we're attached")
Cc: stable <stable@vger.kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|