Age | Commit message (Collapse) | Author |
|
commit 4d820543c54c47a2bd3c95ddbf52f83c89a219a0 upstream.
When using vf_ops->ndo_select_queue, the number of queues of VF is
usually bigger than the synthetic NIC. This condition may happen
often.
Remove "unlikely" from the comparison of ndev->real_num_tx_queues.
Fixes: b3bf5666a510 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c3d897e01aef8ddc43149e4d661b86f823e3aae7 ]
netvsc_vf_xmit() / dev_queue_xmit() will call VF NIC’s ndo_select_queue
or netdev_pick_tx() again. They will use skb_get_rx_queue() to get the
queue number, so the “skb->queue_mapping - 1” will be used. This may
cause the last queue of VF not been used.
Use skb_record_rx_queue() here, so that the skb_get_rx_queue() called
later will get the correct queue number, and VF will be able to use
all queues.
Fixes: b3bf5666a510 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c9864bbccc23e1812ac82966555d68c13ea4006 ]
If the accelerated networking SRIOV VF device has lost carrier
use the synthetic network device which is available as backup
path. This is a rare case since if VF link goes down, normally
the VMBus device will also loose external connectivity as well.
But if the communication is between two VM's on the same host
the VMBus device will still work.
Reported-by: "Shah, Ashish N" <ashish.n.shah@intel.com>
Fixes: 0c195567a8f6 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f6f13c125e05603f68f5bf31f045b95e6d493598 upstream.
When netvsc_attach() is called by operations like changing MTU, etc.,
an extra wakeup may happen while netvsc_attach() calling
rndis_filter_device_add() which sends rndis messages when queue is
stopped in netvsc_detach(). The completion message will wake up queue 0.
We can reproduce the issue by changing MTU etc., then the wake_queue
counter from "ethtool -S" will increase beyond stop_queue counter:
stop_queue: 0
wake_queue: 1
The issue causes queue wake up, and counter increment, no other ill
effects in current code. So we didn't see any network problem for now.
To fix this, initialize tx_disable to true, and set it to false when
the NIC is ready to be attached or registered.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df9f540ca74297a84bafacfa197e9347b20beea5 ]
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2e3 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 171c1fd98df3d5948d9a9eb755274850fa5e59c6 ]
If negotiated NVSP version <= NVSP_PROTOCOL_VERSION_6, the offset may
be wrong (too small) due to a host bug. This can cause missing the
end of the send indirection table, and add multiple zero entries from
leading zeros before the data region. This bug adds extra burden on
channel 0.
So fix the offset by computing it from the data structure sizes. This
will ensure netvsc driver runs normally on unfixed hosts, and future
fixed hosts.
Fixes: 5b54dac856cb ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 71f21959dd5516031db4f011e15e9a9508b93a7d ]
To reach the data region, the existing code adds offset in struct
nvsp_5_send_indirect_table on the beginning of this struct. But the
offset should be based on the beginning of its container,
struct nvsp_message. This bug causes the first table entry missing,
and adds an extra zero from the zero pad after the data region.
This can put extra burden on the channel 0.
So, correct the offset usage. Also add a boundary check to ensure
not reading beyond data region.
Fixes: 5b54dac856cb ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 996ed04741467f6d1552440c92988b132a9487ec ]
The netvsc VF skb handler should make sure that skb is not
shared. Similar logic already exists in bonding and team device
drivers.
This is not an issue in practice because the VF devicex
does not send up shared skb's. But the netvsc driver
should do the right thing if it did.
Fixes: 0c195567a8f6 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 536dc5df2808efbefc5acee334d3c4f701790ec0 ]
kmemleak detects the following memory leak when hot removing
a network device:
unreferenced object 0xffff888083f63600 (size 256):
comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
hex dump (first 32 bytes):
00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00 .@.3............
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
backtrace:
[<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
[<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
[<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
[<00000000046e64f1>] really_probe+0x22f/0xb50
[<000000005cc35eb7>] driver_probe_device+0x25e/0x370
[<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
[<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
[<00000000a72c362f>] bus_probe_device+0x1a6/0x260
[<0000000008478399>] device_add+0x10a3/0x18e0
[<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
[<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
[<000000002c94bb64>] process_one_work+0x919/0x17d0
[<0000000096de6781>] worker_thread+0x87/0xb40
[<00000000fbe7397e>] kthread+0x333/0x3f0
[<000000004f844269>] ret_from_fork+0x3a/0x50
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b0689faa8efc5a3391402d7ae93bd373b7248e51 ]
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 719b85c336ed35565d0f3982269d6f684087bb00 ]
If rndis_filter_open() fails, we need to remove the rndis device created
in earlier steps, before returning an error code. Otherwise, the retry of
netvsc_attach() from its callers will fail and hang.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d0d779dca73cd5acb649c54f81401f93098b298 ]
This fixes a warning of "suspicious rcu_dereference_check() usage"
when nload runs.
Fixes: 776e726bfb34 ("netvsc: fix RCU warning in get_stats")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be4363bdf0ce9530f15aa0a03d1060304d116b15 ]
There is an extra rcu_read_unlock left in netvsc_recv_callback(),
after a previous patch that removes RCU from this function.
This patch removes the extra RCU unlock.
Fixes: 345ac08990b8 ("hv_netvsc: pass netvsc_device to receive callback")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9a33629ba6b26caebd73e3c581ba1e6068c696a7 ]
For better consistency of synthetic NIC names, we set the probe mode to
PROBE_FORCE_SYNCHRONOUS. So the names can be aligned with the vmbus
channel offer sequence.
Fixes: af0a5646cb8d ("use the new async probing feature for the hyperv drivers")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 93aa4792c3908eac87ddd368ee0fe0564148232b ]
When the ring buffer is almost full due to RX completion messages, a
TX packet may reach the "low watermark" and cause the queue stopped.
If the TX completion arrives earlier than queue stopping, the wakeup
may be missed.
This patch moves the check for the last pending packet to cover both
EAGAIN and success cases, so the queue will be reliably waked up when
necessary.
Reported-and-tested-by: Stephan Klein <stephan.klein@wegfinder.at>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b704c4a1ba95574832e730f23817b651db2aa59 ]
After queue stopped, the wakeup mechanism may wake it up again
when ring buffer usage is lower than a threshold. This may cause
send path panic on NULL pointer when we stopped all tx queues in
netvsc_detach and start removing the netvsc device.
This patch fix it by adding a tx_disable flag to prevent unwanted
queue wakeup.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf48648d650db1146b75b9bd358502431e86cf4f ]
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 17d91256898402daf4425cc541ac9cbf64574d9a ]
Changing mtu, channels, or buffer sizes ops call to netvsc_attach(),
rndis_set_subchannel(), which always reset the hash key to default
value. That will override hash key changed previously. This patch
fixes the problem by save the hash key, then restore it when we re-
add the netvsc device.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c9f335a3ff20557a92584199f3d35c7e992bbe5 ]
These assignments occur in multiple places. The patch refactor them
to a function for simplicity. It also puts the struct to heap area
for future expension.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b4a10c750424e01b5e37372fef0a574ebf7b56c3 ]
Hyper-V hosts require us to disable RSS before changing RSS key,
otherwise the changing request will fail. This patch fixes the
coding error.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Reported-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 005479556197f80139771960dda0dfdcd2d2aad5 ]
The VF device's serial number is saved as a string in PCI slot's
kobj name, not the slot->number. This patch corrects the netvsc
driver, so the VF device can be successfully paired with synthetic
NIC.
Fixes: 00d7ddba1143 ("hv_netvsc: pair VF based on serial number")
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Matching network device based on MAC address is problematic
since a non VF network device can be creted with a duplicate MAC
address causing confusion and problems. The VMBus API does provide
a serial number that is a better matching method.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netvsc device is removed it can call reschedule in RCU context.
This happens because canceling the subchannel setup work could (in theory)
cause a reschedule when manipulating the timer.
To reproduce, run with lockdep enabled kernel and unbind
a network device from hv_netvsc (via sysfs).
[ 160.682011] WARNING: suspicious RCU usage
[ 160.707466] 4.19.0-rc3-uio+ #2 Not tainted
[ 160.709937] -----------------------------
[ 160.712352] ./include/linux/rcupdate.h:302 Illegal context switch in RCU read-side critical section!
[ 160.723691]
[ 160.723691] other info that might help us debug this:
[ 160.723691]
[ 160.730955]
[ 160.730955] rcu_scheduler_active = 2, debug_locks = 1
[ 160.762813] 5 locks held by rebind-eth.sh/1812:
[ 160.766851] #0: 000000008befa37a (sb_writers#6){.+.+}, at: vfs_write+0x184/0x1b0
[ 160.773416] #1: 00000000b097f236 (&of->mutex){+.+.}, at: kernfs_fop_write+0xe2/0x1a0
[ 160.783766] #2: 0000000041ee6889 (kn->count#3){++++}, at: kernfs_fop_write+0xeb/0x1a0
[ 160.787465] #3: 0000000056d92a74 (&dev->mutex){....}, at: device_release_driver_internal+0x39/0x250
[ 160.816987] #4: 0000000030f6031e (rcu_read_lock){....}, at: netvsc_remove+0x1e/0x250 [hv_netvsc]
[ 160.828629]
[ 160.828629] stack backtrace:
[ 160.831966] CPU: 1 PID: 1812 Comm: rebind-eth.sh Not tainted 4.19.0-rc3-uio+ #2
[ 160.832952] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012
[ 160.832952] Call Trace:
[ 160.832952] dump_stack+0x85/0xcb
[ 160.832952] ___might_sleep+0x1a3/0x240
[ 160.832952] __flush_work+0x57/0x2e0
[ 160.832952] ? __mutex_lock+0x83/0x990
[ 160.832952] ? __kernfs_remove+0x24f/0x2e0
[ 160.832952] ? __kernfs_remove+0x1b2/0x2e0
[ 160.832952] ? mark_held_locks+0x50/0x80
[ 160.832952] ? get_work_pool+0x90/0x90
[ 160.832952] __cancel_work_timer+0x13c/0x1e0
[ 160.832952] ? netvsc_remove+0x1e/0x250 [hv_netvsc]
[ 160.832952] ? __lock_is_held+0x55/0x90
[ 160.832952] netvsc_remove+0x9a/0x250 [hv_netvsc]
[ 160.832952] vmbus_remove+0x26/0x30
[ 160.832952] device_release_driver_internal+0x18a/0x250
[ 160.832952] unbind_store+0xb4/0x180
[ 160.832952] kernfs_fop_write+0x113/0x1a0
[ 160.832952] __vfs_write+0x36/0x1a0
[ 160.832952] ? rcu_read_lock_sched_held+0x6b/0x80
[ 160.832952] ? rcu_sync_lockdep_assert+0x2e/0x60
[ 160.832952] ? __sb_start_write+0x141/0x1a0
[ 160.832952] ? vfs_write+0x184/0x1b0
[ 160.832952] vfs_write+0xbe/0x1b0
[ 160.832952] ksys_write+0x55/0xc0
[ 160.832952] do_syscall_64+0x60/0x1b0
[ 160.832952] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 160.832952] RIP: 0033:0x7fe48f4c8154
Resolve this by getting RTNL earlier. This is safe because the subchannel
work queue does trylock on RTNL and will detect the race.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the race between netvsc_probe() and
rndis_set_subchannel(), which can cause a deadlock.
These are the related 3 paths which show the deadlock:
path #1:
Workqueue: hv_vmbus_con vmbus_onmessage_work [hv_vmbus]
Call Trace:
schedule
schedule_preempt_disabled
__mutex_lock
__device_attach
bus_probe_device
device_add
vmbus_device_register
vmbus_onoffer
vmbus_onmessage_work
process_one_work
worker_thread
kthread
ret_from_fork
path #2:
schedule
schedule_preempt_disabled
__mutex_lock
netvsc_probe
vmbus_probe
really_probe
__driver_attach
bus_for_each_dev
driver_attach_async
async_run_entry_fn
process_one_work
worker_thread
kthread
ret_from_fork
path #3:
Workqueue: events netvsc_subchan_work [hv_netvsc]
Call Trace:
schedule
rndis_set_subchannel
netvsc_subchan_work
process_one_work
worker_thread
kthread
ret_from_fork
Before path #1 finishes, path #2 can start to run, because just before
the "bus_probe_device(dev);" in device_add() in path #1, there is a line
"object_uevent(&dev->kobj, KOBJ_ADD);", so systemd-udevd can
immediately try to load hv_netvsc and hence path #2 can start to run.
Next, path #2 offloads the subchannal's initialization to a workqueue,
i.e. path #3, so we can end up in a deadlock situation like this:
Path #2 gets the device lock, and is trying to get the rtnl lock;
Path #3 gets the rtnl lock and is waiting for all the subchannel messages
to be processed;
Path #1 is trying to get the device lock, but since #2 is not releasing
the device lock, path #1 has to sleep; since the VMBus messages are
processed one by one, this means the sub-channel messages can't be
procedded, so #3 has to sleep with the rtnl lock held, and finally #2
has to sleep... Now all the 3 paths are sleeping and we hit the deadlock.
With the patch, we can make sure #2 gets both the device lock and the
rtnl lock together, gets its job done, and releases the locks, so #1
and #3 will not be blocked for ever.
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Registering another device with same MAC address (such as TAP, VPN or
DPDK KNI) will confuse the VF autobinding logic. Restrict the search
to only run if the device is known to be a PCI attached VF.
Fixes: e8ff40d4bff1 ("hv_netvsc: improve VF device matching")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
|
|
The recent commit 916c5e1413be ("hv/netvsc: fix handling of fallback
to single queue mode") tried to fix the fallback behavior to a single
queue mode, but it changed the function to return zero incorrectly,
while the function should return an object pointer. Eventually this
leads to a NULL dereference at the callers that expect non-NULL
value.
Fix it by returning the proper net_device object.
Fixes: 916c5e1413be ("hv/netvsc: fix handling of fallback to single queue mode")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements following ethtool stats fields for netvsc:
cpu<n>_tx/rx_packets/bytes
cpu<n>_vf_tx/rx_packets/bytes
Corresponding per-cpu counters already exist in current code. Exposing
these counters will help troubleshooting performance issues.
for_each_present_cpu() was used instead of for_each_possible_cpu().
for_each_possible_cpu() would create very long and useless output.
It is still being used for internal buffer, but not for ethtool
output.
There could be an overflow if cpu was added between ethtool
call netvsc_get_sset_count() and netvsc_get_ethtool_stats() and
netvsc_get_strings(). (still safe if cpu was removed)
ethtool makes these three function calls separately.
As long as we use ethtool, I can't see any clean solution.
Currently and in foreseeable short term, Hyper-V doesn't support
cpu hot-plug. Plus, ethtool is for admin use. Unlikely the admin
would perform such combo operations.
Changes in v2:
- Remove cpp style comment
- Resubmit after freeze
Changes in v3:
- Reimplemented with kvmalloc instead of alloc_percpu
Changes in v4:
- Fixed inconsistent array size
- Use kvmalloc_array instead of kvmalloc
Signed-off-by: Yidong Ren <yidren@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts were trivial overlapping changes, so reasonably
easy to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If out ring is full temporarily and receive completion cannot go out,
we may still need to reschedule napi if certain conditions are met.
Otherwise the napi poll might be stopped forever, and cause network
disconnect.
Fixes: 7426b1a51803 ("netvsc: optimize receive completions")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1a641 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Recent kernels support asynchronous probing; most hyperv drivers
can be probed async easily so set the required flag for this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.
When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: Thomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e49850c5e ("netvsc: fix race on sub channel creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These fields in struct ndis_ipsecv2_offload and struct ndis_rsc_offload
are one byte according to the specs. This patch defines them with the
right size. These structs are not in use right now, but will be used soon.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VF is added, the paravirtual device is already present
and may have been moved to another network namespace. For example,
sometimes the management interface is put in another net namespace
in some environments.
The VF should get moved to where the netvsc device is when the
VF is discovered. The user can move it later (if desired).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When finding the parent netvsc device, the search needs to be across
all netvsc device instances (independent of network namespace).
Find parent device of VF using upper_dev_get routine which
searches only adjacent list.
Fixes: e8ff40d4bff1 ("hv_netvsc: improve VF device matching")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
netns aware byref
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The callback model of handling network failover is not suitable
in the current form.
1. It was merged without addressing all the review feedback.
2. It was merged without approval of any of the netvsc maintainers.
3. Design discussion on how to handle PV/VF fallback is still
not complete.
4. IMHO the code model using callbacks is trying to make
something common which isn't.
Revert the netvsc specific changes for now. Does not impact ongoing
development of failover model for virtio.
Revisit this after a simpler library based failover kernel
routines are extracted.
This reverts
commit 9c6ffbacdb57 ("hv_netvsc: fix error return code in netvsc_probe()")
and
commit 1ff78076d8dd ("netvsc: refactor notifier/event handling code to use the failover framework")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix several bpfilter/UMH bugs, in particular make the UMH build not
depend upon X86 specific Kconfig symbols. From Alexei Starovoitov.
2) Fix handling of modified context pointer in bpf verifier, from
Daniel Borkmann.
3) Kill regression in ifdown/ifup sequences for hv_netvsc driver, from
Dexuan Cui.
4) When the bonding primary member name changes, we have to re-evaluate
the bond->force_primary setting, from Xiangning Yu.
5) Eliminate possible padding beyone end of SKB in cdc_ncm driver, from
Bjørn Mork.
6) RX queue length reported for UDP sockets in procfs and socket diag
are inaccurate, from Paolo Abeni.
7) Fix br_fdb_find_port() locking, from Petr Machata.
8) Limit sk_rcvlowat values properly in TCP, from Soheil Hassas
Yeganeh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
tcp: limit sk_rcvlowat by the maximum receive buffer
net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620
socket: close race condition between sock_close() and sockfs_setattr()
net: bridge: Fix locking in br_fdb_find_port()
udp: fix rx queue len reported by diag and proc interface
cdc_ncm: avoid padding beyond end of skb
net/sched: act_simple: fix parsing of TCA_DEF_DATA
net: fddi: fix a possible null-ptr-deref
net: aquantia: fix unsigned numvecs comparison with less than zero
net: stmmac: fix build failure due to missing COMMON_CLK dependency
bpfilter: fix race in pipe access
bpf, xdp: fix crash in xdp_umem_unaccount_pages
xsk: Fix umem fill/completion queue mmap on 32-bit
tools/bpf: fix selftest get_cgroup_id_user
bpfilter: fix OUTPUT_FORMAT
umh: fix race condition
net: mscc: ocelot: Fix uninitialized error in ocelot_netdevice_event()
bonding: re-evaluate force_primary when the primary slave name changes
ip_tunnel: Fix name string concatenate in __ip_tunnel_create()
hv_netvsc: Fix a network regression after ifdown/ifup
...
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
|
|
Recently people reported the NIC stops working after
"ifdown eth0; ifup eth0". It turns out in this case the TX queues are not
enabled, after the refactoring of the common detach logic: when the NIC
has sub-channels, usually we enable all the TX queues after all
sub-channels are set up: see rndis_set_subchannel() ->
netif_device_attach(), but in the case of "ifdown eth0; ifup eth0" where
the number of channels doesn't change, we also must make sure the TX queues
are enabled. The patch fixes the regression.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the failover register fail
error handling case instead of 0, as done elsewhere in this function.
Fixes: 1ff78076d8dd ("netvsc: refactor notifier/event handling code to use the failover framework")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the registration/notification framework supported by the generic
failover infrastructure.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the guest network adapter is not configured with DeviceNaming
enabled on the host, then the query for friendly name will return
success but with a zero length name. Which then leads to a garbage value
(stack contents) for ifalias.
Fix is simple, just don't set name if host doesn't return it.
Fixes: 0fe554a46a0f ("hv_netvsc: propogate Hyper-V friendly name into interface alias")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The handlers for ethtool get/set msg level are missing from netvsc.
This patch adds them.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hyper-v transparent bonding should have used master_dev_link.
The netvsc device should look like a master bond device not
like the upper side of a tunnel.
This makes the semantics the same so that userspace applications
looking at network devices see the correct master relationshipship.
Fixes: 0c195567a8f6 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix simple misspelling kashkey_offset should be hashkey_offset.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|