| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 9cb1d19f47fafad7dcf7c8564e633440c946cfd7 ]
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08dad2f4d541fcfe5e7bfda72cc6314bbfd2802f ]
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4367355dd90942a71641c98c40c74589c9bddf90 ]
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1adb20f0d496b2c61e9aa1f4761b8d71f93d258e ]
The register starts from 0x800 is the 16th MAC address register rather
than the first one.
Fixes: cffb13f4d6fb ("stmmac: extend mac addr reg and fix perfect filering")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0c32a96d000f260b5ebfabb4145a86ae1cd71847 upstream.
In case clk_prepare() fails, capture and propagate the error code up the
stack. If regulator_enable() was called earlier, properly unwind it by
calling regulator_disable().
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-22-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bee1b0511844c8c79fccf1f2b13472393b6b91f7 upstream.
This reverts commit f86a3b83833e7cfe558ca4d70b64ebc48903efec.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: David S. Miller <davem@davemloft.net>
Fixes: f86a3b83833e ("net: stmicro: fix a missing check of clk_prepare")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8a7cb245cf28cb3e541e0d6c8624b95d079e155b ]
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e127906b68b49ddb3ecba39ffa36a329c48197d3 ]
Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 014dfa26ce1c647af09bf506285ef67e0e3f0a6b ]
MTU cannot be changed on dwmac-sun8i. (ip link set eth0 mtu xxx returning EINVAL)
This is due to tx_fifo_size being 0, since this value is used to compute valid
MTU range.
Like dwmac-sunxi (with commit 806fd188ce2a ("net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes"))
dwmac-sun8i need to have tx and rx fifo sizes set.
I have used values from datasheets.
After this patch, setting a non-default MTU (like 1000) value works and network is still useable.
Tested-on: sun8i-h3-orangepi-pc
Tested-on: sun8i-r40-bananapi-m2-ultra
Tested-on: sun50i-a64-bananapi-m64
Tested-on: sun50i-h5-nanopi-neo-plus2
Tested-on: sun50i-h6-pine-h64
Fixes: 9f93ac8d408 ("net-next: stmmac: Add dwmac-sun8i")
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c511819d138de38e1637eedb645c207e09680d0f upstream.
stmmac_xmit() call stmmac_tx_timer_arm() at the end to modify tx timer to
do the transmission cleanup work. Imagine such a situation, stmmac enters
suspend immediately after tx timer modified, it's expire callback
stmmac_tx_clean() would not be invoked. This could affect BQL, since
netdev_tx_sent_queue() has been called, but netdev_tx_completed_queue()
have not been involved, as a result, dql_avail(&dev_queue->dql) finally
always return a negative value.
__dev_queue_xmit->__dev_xmit_skb->qdisc_run->__qdisc_run->qdisc_restart->dequeue_skb:
if ((q->flags & TCQ_F_ONETXQUEUE) &&
netif_xmit_frozen_or_stopped(txq)) // __QUEUE_STATE_STACK_XOFF is set
Net core will stop transmitting any more. Finillay, net watchdong would timeout.
To fix this issue, we should call netdev_tx_reset_queue() in stmmac_resume().
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3e860a83397bf761ec1128a3f0ba186445992c6 upstream.
If clear GMAC_CONFIG_TE bit, it would stop all tx channels, but users
may only want to stop specific tx channel.
Fixes: 48863ce5940f ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 879c348c35bb5fb758dd881d8a97409c1862dae8 upstream.
We introduce dwmac410_dma_init_channel() here for both EQoS v4.10 and
above which use different DMA_CH(n)_Interrupt_Enable bit definitions for
NIE and AIE.
Fixes: 48863ce5940f ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f317e2ea8c88737aa36228167b2292baef3f0430 ]
When disable CBS, mode_to_use parameter is not updated even the operation
mode of Tx Queue is changed to Data Centre Bridging (DCB). Therefore,
when tc_setup_cbs() function is called to re-enable CBS, the operation
mode of Tx Queue remains at DCB, which causing CBS fails to work.
This patch updates the value of mode_to_use parameter to MTL_QUEUE_DCB
after operation mode of Tx Queue is changed to DCB in stmmac_dma_qmode()
callback function.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/1612447396-20351-1-git-send-email-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5b55299eed78538cc4746e50ee97103a1643249c ]
Since the original mtu is not used when the mtu is updated,
the mtu is aligned with cache, this will get an incorrect.
For example, if you want to configure the mtu to be 1500,
but mtu 1536 is configured in fact.
Fixed: eaf4fac478077 ("net: stmmac: Do not accept invalid MTU values")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20210113034109.27865-1-david.wu@rock-chips.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b8239638853e3e37b287e4bd4d57b41f14c78550 ]
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 529254216773acd5039c07aa18cf06fd1f9fccdd ]
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 82ca4c922b8992013a238d65cf4e60cc33e12f36 ]
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5f58591323bf3f342920179f24515935c4b5fd60 ]
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2ae0b ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ec236c7c51f89abb0224a4da4a6b77f9beb6600 ]
When do suspend/resume test, there have WARN_ON() log dump from
stmmac_xmit() funciton, the code logic:
entry = tx_q->cur_tx;
first_entry = entry;
WARN_ON(tx_q->tx_skbuff[first_entry]);
In normal case, tx_q->tx_skbuff[txq->cur_tx] should be NULL because
the skb should be handled and freed in stmmac_tx_clean().
But stmmac_resume() reset queue parameters like below, skb buffers
may not be freed.
tx_q->cur_tx = 0;
tx_q->dirty_tx = 0;
So free tx skb buffer in stmmac_resume() to avoid warning and
memory leak.
log:
[ 46.139824] ------------[ cut here ]------------
[ 46.144453] WARNING: CPU: 0 PID: 0 at drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3235 stmmac_xmit+0x7a0/0x9d0
[ 46.154969] Modules linked in: crct10dif_ce vvcam(O) flexcan can_dev
[ 46.161328] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 5.4.24-2.1.0+g2ad925d15481 #1
[ 46.170369] Hardware name: NXP i.MX8MPlus EVK board (DT)
[ 46.175677] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 46.180465] pc : stmmac_xmit+0x7a0/0x9d0
[ 46.184387] lr : dev_hard_start_xmit+0x94/0x158
[ 46.188913] sp : ffff800010003cc0
[ 46.192224] x29: ffff800010003cc0 x28: ffff000177e2a100
[ 46.197533] x27: ffff000176ef0840 x26: ffff000176ef0090
[ 46.202842] x25: 0000000000000000 x24: 0000000000000000
[ 46.208151] x23: 0000000000000003 x22: ffff8000119ddd30
[ 46.213460] x21: ffff00017636f000 x20: ffff000176ef0cc0
[ 46.218769] x19: 0000000000000003 x18: 0000000000000000
[ 46.224078] x17: 0000000000000000 x16: 0000000000000000
[ 46.229386] x15: 0000000000000079 x14: 0000000000000000
[ 46.234695] x13: 0000000000000003 x12: 0000000000000003
[ 46.240003] x11: 0000000000000010 x10: 0000000000000010
[ 46.245312] x9 : ffff00017002b140 x8 : 0000000000000000
[ 46.250621] x7 : ffff00017636f000 x6 : 0000000000000010
[ 46.255930] x5 : 0000000000000001 x4 : ffff000176ef0000
[ 46.261238] x3 : 0000000000000003 x2 : 00000000ffffffff
[ 46.266547] x1 : ffff000177e2a000 x0 : 0000000000000000
[ 46.271856] Call trace:
[ 46.274302] stmmac_xmit+0x7a0/0x9d0
[ 46.277874] dev_hard_start_xmit+0x94/0x158
[ 46.282056] sch_direct_xmit+0x11c/0x338
[ 46.285976] __qdisc_run+0x118/0x5f0
[ 46.289549] net_tx_action+0x110/0x198
[ 46.293297] __do_softirq+0x120/0x23c
[ 46.296958] irq_exit+0xb8/0xd8
[ 46.300098] __handle_domain_irq+0x64/0xb8
[ 46.304191] gic_handle_irq+0x5c/0x148
[ 46.307936] el1_irq+0xb8/0x180
[ 46.311076] cpuidle_enter_state+0x84/0x360
[ 46.315256] cpuidle_enter+0x34/0x48
[ 46.318829] call_cpuidle+0x18/0x38
[ 46.322314] do_idle+0x1e0/0x280
[ 46.325539] cpu_startup_entry+0x24/0x40
[ 46.329460] rest_init+0xd4/0xe0
[ 46.332687] arch_call_rest_init+0xc/0x14
[ 46.336695] start_kernel+0x420/0x44c
[ 46.340353] ---[ end trace bc1ee695123cbacd ]---
Fixes: 47dd7a540b8a0 ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f19306d166688a73356aa636c62e698bf2063cc ]
The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.
Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.
Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7241c5a697479c7d0c5a96595822cdab750d41ae ]
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58ad6 ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 592d751c1e174df5ff219946908b005eb48934b3 upstream.
If we don't have a hardware multicast filter available then instead of
silently failing to listen for the requested ethernet broadcast
addresses fall back to receiving all multicast packets, in a similar
fashion to other drivers with no multicast filter.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df43dd526e6609769ae513a81443c7aa727c8ca3 upstream.
The IPQ806x does not appear to have a functional multicast ethernet
address filter. This was observed as a failure to correctly receive IPv6
packets on a LAN to the all stations address. Checking the vendor driver
shows that it does not attempt to enable the multicast filter and
instead falls back to receiving all multicast packets, internally
setting ALLMULTI.
Use the new fallback support in the dwmac1000 driver to correctly
achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6
functionality on an RB3011 router.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a96ac8a0045e3cbe3e5af6d1b3c78c6c2065dec5 ]
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f42234ffd531ca6b13d9da02faa60b72eccf8334 ]
The paranoidal pointer check in IRQ handler looks very strange - it
really protects us only against bogus drivers which request IRQ line
with null pointer dev_id. However, the code fragment is incorrect
because the dev pointer is used before the actual check which leads
to undefined behavior. Remove the check to avoid confusing people
with incorrect code.
Signed-off-by: Maxim Petrov <mmrmaximuzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91a2559c1dc5b0f7e1256d42b1508935e8eabfbf ]
In fine adjustement mode, which is the current default, the sub-second
increment register is the number of nanoseconds that will be added to
the clock when the accumulator overflows. At each clock cycle, the
value of the addend register is added to the accumulator.
Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
frequency of the ptp clock actually is.
The adjustment is then done on the addend register, only incrementing
every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
(addend = 2^32 * 50MHz/ptp_clock_rate).
This causes the following issues :
- In case the frequency of the ptp clock is inferior or equal to 50MHz,
the addend value calculation will overflow and the default
addend value will be set to 0, causing the clock to not work at
all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
- The resolution of the timestamping clock is limited to 20ns while it
is not needed, thus limiting the accuracy of the timestamping to
20ns.
Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
It will allow to reach the minimum possible frequency for
ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
sub-second-increment to a higher value. For instance, for 25MHz, it
gives ssinc = 80ns and default_addend = 2^31.
It will also allow to use a lower value for sub-second-increment, thus
improving the timestamping accuracy with frequencies higher than
100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
2^31.
v1->v2:
- Remove modifications to the calculation of default addend, which broke
compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
is not an integer.
- Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 15ce30609d1e88d42fb1cd948f453e6d5f188249 ]
There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0212a5ebfa6cd789ab47666b9cc169e6e688732 ]
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b9c ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 806fd188ce2a4f8b587e83e73c478e6484fbfa55 ]
After commit bfcb813203e619a8960a819bf533ad2a108d8105 ("net: dsa:
configure the MTU for switch ports") my Lamobo R1 platform which uses
an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail
by rejecting a MTU of 1536. The reason for that is that the DMA
capabilities are not readable on this version of the IP, and there
is also no 'tx-fifo-depth' property being provided in Device Tree. The
property is documented as optional, and is not provided.
Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so
provide these values through platform data as an immediate fix until
various Device Tree sources get updated accordingly.
Fixes: eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3e1221acf6a8f8595b5ce354bab4327a69d54d18 ]
Commit 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address entries")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9de9aa487daff7a5c73434c24269b44ed6a428e6 ]
Make sure we clean up devicetree related configuration
also when clock init fails.
Fixes: fecd4d7eef8b ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b723bd933980f4956dabc8a8d84b3e83be8d094c ]
ACS (auto PAD/FCS stripping) removes FCS off 802.3 packets (LLC) so that
there is no need to manually strip it for such packets. The enhanced DMA
descriptors allow to flag LLC packets so that the receiving callback can
use that to strip FCS manually or not. On the other hand, normal
descriptors do not support that.
Thus in order to not truncate LLC packet ACS should be disabled when
using normal DMA descriptors.
Fixes: 47dd7a540b8a0 ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 14b41a2959fbaa50932699d32ceefd6643abacc6 ]
When running v5.5 with a rootfs on NFS, memory abort may happen in
the system resume stage:
Unable to handle kernel paging request at virtual address dead00000000012a
[dead00000000012a] address between user and kernel address ranges
pc : run_timer_softirq+0x334/0x3d8
lr : run_timer_softirq+0x244/0x3d8
x1 : ffff800011cafe80 x0 : dead000000000122
Call trace:
run_timer_softirq+0x334/0x3d8
efi_header_end+0x114/0x234
irq_exit+0xd0/0xd8
__handle_domain_irq+0x60/0xb0
gic_handle_irq+0x58/0xa8
el1_irq+0xb8/0x180
arch_cpu_idle+0x10/0x18
do_idle+0x1d8/0x2b0
cpu_startup_entry+0x24/0x40
secondary_start_kernel+0x1b4/0x208
Code: f9000693 a9400660 f9000020 b4000040 (f9000401)
---[ end trace bb83ceeb4c482071 ]---
Kernel panic - not syncing: Fatal exception in interrupt
SMP: stopping secondary CPUs
SMP: failed to stop secondary CPUs 2-3
Kernel Offset: disabled
CPU features: 0x00002,2300aa30
Memory Limit: none
---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
It's found that stmmac_xmit() and stmmac_resume() sometimes might
run concurrently, possibly resulting in a race condition between
mod_timer() and setup_timer(), being called by stmmac_xmit() and
stmmac_resume() respectively.
Since the resume() runs setup_timer() every time, it'd be safer to
have del_timer_sync() in the suspend() as the counterpart.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 520cf6002147281d1e7b522bb338416b623dcb93 ]
Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0
in register MAC_PPS_CONTROL is set it selects the functionality
command in the same register, otherwise selects the functionality
control.
Command functionality is required to either enable (command 0x2)
and disable (command 0x5) the flexible PPS output, but the bit
PPSEN0 is currently set only for enabling.
Set the bit PPSEN0 to properly disable flexible PPS output.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 9a8a02c9d46d ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5da202c88f8c355ad79bc2e8eb582e6d433060e7 ]
The field "name" in struct ptp_clock_info has a fixed size of 16
chars and is used as zero terminated string by clock_name_show()
in drivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the
null termination, and this causes overflow to the next bytes in
the struct when the string is read as null terminated:
hexdump -C /sys/class/ptp/ptp0/clock_name
00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock|
00000010 a0 ac b9 03 0a |.....|
where the extra 4 bytes (excluding the newline) after the string
represent the integer 0x03b9aca0 = 62500000 assigned to the field
"max_adj" that follows "name" in the same struct.
There is no strict requirement for the "name" content and in the
comment in ptp_clock_kernel.h it's reported it should just be 'A
short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 25683bab09a70542b9f8e3e28f79b3369e56701f ]
Some setups may not have all Unicast addresses filters available. Check
the number of available filters before trying to setup it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 231042181dc9d6122c6faba64e99ccb25f13cc6c ]
The "gmac->phy_mode" variable is an enum and in this context GCC will
treat it as an unsigned int so the error handling will never be
triggered.
Fixes: b1c17215d718 ("stmmac: add ipq806x glue layer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f10210517a2f37feea2edf85eb34c98977265c16 ]
The "dwmac->phy_mode" is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 566e82516253 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b2f3a481c4cd62f78391b836b64c0a6e72b503d2 upstream.
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8605131747e7e1fd8f6c9f97a00287aae2b2c640 upstream.
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 52cc73e5404c7ba0cbfc50cb4c265108c84b3d5a ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba80 ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f1239d8aa84dad8fe4b6cc1356f40fc8e842db47 ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4772f26db8d1fb568c4862c538344a1b5fb52081 ]
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be11 ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d558f0294fe92e04af192e221d0d0f6a180ee7b ]
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11d55fd9975f8e46a0e5e19c14899544e81e1e15 ]
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eaf4fac478077d4ed57cbca2c044c4b58a96bd98 ]
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd6f48546b9cb7a785344fc78058c420923d7ed8 ]
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f86a3b83833e7cfe558ca4d70b64ebc48903efec ]
clk_prepare() could fail, so let's check its status, and if it fails,
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 40a1dcee2d1846a24619fe9ca45c661ca0db7dda upstream.
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e497c20e203680aba9ccf7bb475959595908ca7e ]
disable ptp_ref_clk in suspend flow, and enable it in resume flow.
Fixes: f573c0b9c4e0 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Herve Codina
Jesper Nilsson
Nathan Chancellor
Jisheng Zhang
Anirudh Rayabharam
Greg Kroah-Hartman
Yannick Vignon
Jonathan McDowell
Corentin Labbe
Joakim Zhang
Ong Boon Leong
Mohammad Athari Bin Ismail
David Wu
Samuel Holland
Martin Blumenstingl
Fugang Duan
Voon Weifeng
Maxim Petrov
Julien Beraud
Marc Zyngier
Florian Fainelli
Emil Renner Berthing
Remi Pommarel
Nicolin Chen
Antonio Borneo
Jose Abreu
Dan Carpenter
Chen-Yu Tsai
Kangjie Lu
Biao Huang