| Age | Commit message (Collapse) | Author |
|---|
|
Make the code more readable by moving the initial checksum setup
and the command/status preparation to its own function.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in mv643xx_eth_xmit and
txq_submit_skb that can be called in hard irq and other contexts,
on paths where the skbs are dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
When using phydev, it should be phy_start/phy_stop'ed properly. This
driver doesn't do that, so add the corresponding calls to port_start/
stop respectively.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of open-coding a PHY reset through the MII BMCR register, use
phy_init_hw() which does that for us and will also make sure that PHY
fixups are applied if required. We also remove a call to phy_reset()
due to the following sequence of calls in the driver:
phy_scan()
-> phy_connect()
-> phy_connect_direct()
-> phy_attach_direct()
-> phy_init_hw()
and we only have a call to phy_init() after phy_scan().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Olof Johansson <olof@lixom.net>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Nicolas Pitre <nico@fluxnic.net>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We assume that "mp->phy" can be NULL a couple lines before the
dereference.
Fixes: 1cce16d37d0f ('net: mv643xx_eth: Add missing phy_addr_set in DT mode')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit cc9d4598 'net: mv643xx_eth: use of_phy_connect if phy_node
present' made the call to phy_scan optional, if the DT has a link to
the phy node.
However phy_scan has the side effect of calling phy_addr_set, which
writes the phy MDIO address to the ethernet controller. If phy_addr_set
is not called, and the bootloader has not set the correct address then
the driver will fail to function.
Tested on Kirkwood.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DT-based mv643xx_eth probes and creates platform_devices for the
port devices on its own. To allow fixups for ports based on the
device_node, we need to set .of_node of the corresponding device
with the correct node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The periodic statistics timer gets started at port _probe() time, but
is stopped on _stop() only. In a modular environment, this can cause
the timer to access already deallocated memory, if the module is unloaded
without starting the eth device. To fix this, we add the timer right
before the port is started, instead of at _probe() time.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each port driver installs a periodic timer to update port statistics
by calling mib_counters_update. As mib_counters_update is also called
from non-timer context, we should not reschedule the timer there but
rather move it to timer-only context.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port number is only local to the ethernet block, not global, so
there can be two ethernet blocks both using the same port, like
kirkwood with both using port 0.
Fix this by using the array index offset for the allocated platform
devices as the id.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Zero pointer in rx_skb is how respective rxq_deinit() finds out out that a skb
slot is unallocated. If rxq_refill() fails (e.g. on OOM condition), subsequent
teardown would result in an attempt to kfree() invalid pointers.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The change set of 4305b541 "[SK_BUFF]: Convert skb->end to sk_buff_data_t"
converted skb->end from pointer to sk_buff_data_t.
The pointed value should be accessed via skb_end_pointer().
Since arm or ppc arch doesn't define NET_SKBUFF_DATA_USES_OFFSET,
skb->end is effectively pointer. So it doesn't cause a real problem.
But this patch is good for consistency.
Found by inspection. Compile test only.
Cc: Simon Horman <horms@verge.net.au>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
76723bca28 "net: mv643xx_eth: add DT parsing support" added a
dummy mv643xx_eth_shared_of_probe() fallback function with a
typo.
This adds the missing semicolon so we can build without CONFIG_OF
again, and changes both dummy functions to the more conventional
"static inline" syntax, which can avoid potential problems with
the empty macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds device tree parsing support for the shared driver of mv643xx_eth.
As the bindings are slightly different from current PPC bindings new binding
documentation is also added. Following PPC-style device setup, the shared
driver now also adds port platform_devices and sets up port platform_data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethernet controllers found on Kirkwood SoCs not only suffer from loosing
MAC address register contents on clock gating but also some important
registers are reset to values that would break ethernet. This patch
clears the CLK125_BYPASS_EN bit for DT enabled Kirkwood only by using
of_device_is_compatible() instead of #ifdefs. Non-DT Kirkwood is not
affected as it installs a clock gating workaround because of the MAC
address issue above. Other Orion SoCs do not suffer from register reset,
do not have the bit in question, or do not have the register at all.
Moreover, system controllers on PPC using this driver should also be
protected from clearing that bit.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This connects to a phy node passed to the port device instead of probing
the phy by phy_addr.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of managed devm_ioremap and remove corresponding iounmap.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using a separated mdio bus driver with mvmdio, phy_detach on network device
removal will not stop the phy and finally lead to NULL pointer dereference
in mvmdio due to non-existent network device. Use phy_disconnect instead
to properly stop phy device from accessing network device prior removal of
the network device.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the interface is shutdown, the mv643xx_eth driver hits the following
lockdep dump:
=================================
[ INFO: inconsistent lock state ]
3.8.0+ #303 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
NetworkManager/3449 [HC0[0]:SC0[0]:HE1:SE1] takes:
(_xmit_ETHER#2){+.?...}, at: [<c02828e4>] txq_reclaim+0x60/0x230
{IN-SOFTIRQ-W} state was registered at:
[<c007e93c>] mark_irqflags+0xf8/0x1c4
[<c007ee60>] __lock_acquire+0x458/0x9a4
[<c007f8b0>] lock_acquire+0x60/0x74
[<c03ea914>] _raw_spin_lock+0x40/0x50
[<c0334040>] sch_direct_xmit+0xa4/0x2e4
[<c0320880>] dev_queue_xmit+0x174/0x508
[<c03953b0>] ip6_finish_output2+0xd0/0x3c4
[<c03b15bc>] mld_sendpack+0x190/0x368
[<c03b3204>] mld_ifc_timer_expire+0xc/0x58
[<c005133c>] call_timer_fn+0x6c/0xe0
[<c0051588>] run_timer_softirq+0x1d8/0x210
[<c004c004>] __do_softirq+0xe0/0x1b4
[<c004c448>] irq_exit+0x64/0x6c
[<c000f1e0>] handle_IRQ+0x34/0x84
[<c000e0d0>] __irq_usr+0x30/0x80
irq event stamp: 160603
hardirqs last enabled at (160603): [<c00c736c>] kfree+0xa8/0xe8
hardirqs last disabled at (160602): [<c00c72e0>] kfree+0x1c/0xe8
softirqs last enabled at (160304): [<c028260c>] mib_counters_update+0x5ec/0x60c
softirqs last disabled at (160302): [<c03eab8c>] _raw_spin_lock_bh+0x14/0x54
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
<Interrupt>
lock(_xmit_ETHER#2);
*** DEADLOCK ***
1 lock held by NetworkManager/3449:
#0: (rtnl_mutex){+.+.+.}, at: [<c032e664>] rtnetlink_rcv+0xc/0x24
stack backtrace:
[<c0013e34>] (unwind_backtrace+0x0/0xf8) from [<c007e12c>] (print_usage_bug+0x150/0x1d4)
[<c007e12c>] (print_usage_bug+0x150/0x1d4) from [<c007e3f8>] (mark_lock_irq+0x248/0x290)
[<c007e3f8>] (mark_lock_irq+0x248/0x290) from [<c007e598>] (mark_lock+0x158/0x404)
[<c007e598>] (mark_lock+0x158/0x404) from [<c007e97c>] (mark_irqflags+0x138/0x1c4)
[<c007e97c>] (mark_irqflags+0x138/0x1c4) from [<c007ee60>] (__lock_acquire+0x458/0x9a4)
[<c007ee60>] (__lock_acquire+0x458/0x9a4) from [<c007f8b0>] (lock_acquire+0x60/0x74)
[<c007f8b0>] (lock_acquire+0x60/0x74) from [<c03ea914>] (_raw_spin_lock+0x40/0x50)
[<c03ea914>] (_raw_spin_lock+0x40/0x50) from [<c02828e4>] (txq_reclaim+0x60/0x230)
[<c02828e4>] (txq_reclaim+0x60/0x230) from [<c0282ad8>] (txq_deinit+0x24/0xcc)
[<c0282ad8>] (txq_deinit+0x24/0xcc) from [<c0282d28>] (mv643xx_eth_stop+0x1a8/0x1bc)
[<c0282d28>] (mv643xx_eth_stop+0x1a8/0x1bc) from [<c031e314>] (__dev_close_many+0x88/0xcc)
[<c031e314>] (__dev_close_many+0x88/0xcc) from [<c031e380>] (__dev_close+0x28/0x3c)
[<c031e380>] (__dev_close+0x28/0x3c) from [<c0320fa0>] (__dev_change_flags+0x7c/0x134)
[<c0320fa0>] (__dev_change_flags+0x7c/0x134) from [<c03210e0>] (dev_change_flags+0x10/0x48)
[<c03210e0>] (dev_change_flags+0x10/0x48) from [<c032da1c>] (do_setlink+0x1a0/0x730)
[<c032da1c>] (do_setlink+0x1a0/0x730) from [<c032f524>] (rtnl_newlink+0x304/0x4b0)
[<c032f524>] (rtnl_newlink+0x304/0x4b0) from [<c032ef8c>] (rtnetlink_rcv_msg+0x25c/0x2a0)
[<c032ef8c>] (rtnetlink_rcv_msg+0x25c/0x2a0) from [<c03383a0>] (netlink_rcv_skb+0xbc/0xd8)
[<c03383a0>] (netlink_rcv_skb+0xbc/0xd8) from [<c032e674>] (rtnetlink_rcv+0x1c/0x24)
[<c032e674>] (rtnetlink_rcv+0x1c/0x24) from [<c03361d8>] (netlink_unicast_kernel+0x88/0xd4)
[<c03361d8>] (netlink_unicast_kernel+0x88/0xd4) from [<c0337dd0>] (netlink_unicast+0x138/0x180)
[<c0337dd0>] (netlink_unicast+0x138/0x180) from [<c0338020>] (netlink_sendmsg+0x208/0x32c)
[<c0338020>] (netlink_sendmsg+0x208/0x32c) from [<c030ab48>] (sock_sendmsg+0x84/0xa4)
[<c030ab48>] (sock_sendmsg+0x84/0xa4) from [<c030aef4>] (__sys_sendmsg+0x2ac/0x2c4)
[<c030aef4>] (__sys_sendmsg+0x2ac/0x2c4) from [<c030c8ec>] (sys_sendmsg+0x3c/0x68)
[<c030c8ec>] (sys_sendmsg+0x3c/0x68) from [<c000e2e0>] (ret_fast_syscall+0x0/0x3c)
It seems that txq_reclaim() takes the netif tx lock:
__netif_tx_lock(nq, smp_processor_id());
in a context outside of softirq context, and thus is susceptible to
deadlock should an interrupt occur.
Use __netif_tx_lock_bh()/__netif_tx_unlock_bh() instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
3.10-rc1 issues the following warning:
netif_napi_add() called with weight 128 on device eth%d
This patch reduce the weight to 64, using NAPI_POLL_WEIGHT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent support for GRO, there is no need to keep both LRO and
GRO. This patch therefore removes the deprecated inet_lro support
from mv643xx_eth. This is work is based on an experimental patch
provided by Eric Dumazet and Willy Tarreau.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Based-on-patch-by: Eric Dumazet <eric.dumazet@gmail.com>
Based-on-patch-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds GRO support to mv643xx_eth by making it invoke
napi_gro_receive instead of netif_receive_skb.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves shared private data kzalloc to managed devm_kzalloc and
cleans now unneccessary kfree and error handling.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds an optional shared block clock to avoid lockups on
clock gated controllers. Besides the new clock, clock handling for
existing clocks is cleaned up and moved to devm_clk_get. Device
tree binding documentation is updated for the new clocks property.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When both the Marvell MV643XX ethernet driver and the Orion MDIO driver
are compiled as modules, the ethernet driver may be probed before the
MDIO driver. Let mv643xx_eth_probe() return EPROBE_DEFER in this case,
i.e. when it cannot find the PHY.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts the Marvell MV643XX ethernet driver to use the
Marvell Orion MDIO driver. As a result, PowerPC and ARM platforms
registering the Marvell MV643XX ethernet driver are also updated to
register a Marvell Orion MDIO driver. This driver voluntarily overlaps
with the Marvell Ethernet shared registers because it will use a subset
of this shared register (shared_base + 0x4 to shared_base + 0x84). The
Ethernet driver is also updated to look up for a PHY device using the
Orion MDIO bus driver.
For ARM and PowerPC we register a single instance of the "mvmdio" driver
in the system like it used to be done with the use of the "shared_smi"
platform_data cookie on ARM.
Note that it is safe to register the mvmdio driver only for the "ge00"
instance of the driver because this "ge00" interface is guaranteed to
always be explicitely registered by consumers of
arch/arm/plat-orion/common.c and other instances (ge01, ge10 and ge11)
were all pointing their shared_smi to ge00. For PowerPC the in-tree
Device Tree Source files mention only one MV643XX ethernet MAC instance
so the MDIO bus driver is registered only when id == 0.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When autoneg has been disabled in the PHY (Marvell 88E1118 here), auto
negotiation between MAC and PHY seem non-functional anymore. The only
way I found to workaround this is to manually configure the MAC with the
settings sent to the PHY earlier.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.
Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.
With help from Maxime Bizon, who pointed out that commit
87151b8689d (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.
Instead of fixing this bug, lets remove skb recycling.
Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From Andrew Lunn <andrew@lunn.ch>:
* 'v3.5-rc7-fixes' of git://github.com/lunn/linux:
ARM: Kirkwood: Replace mrvl with marvell
ARM: Orion: fix driver probe error handling with respect to clk
ARM: Dove: Fixup ge00 initialisation
ARM: Kirkwood: Fix PHY disable clk problems
ARM: Kirkwood: Ensure runit clock always ticks.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>
|
|
|
|
Commit 452503ebc (ARM: Orion: Eth: Add clk/clkdev support.) broke
the building of the driver on architectures which don't have clk
support. In particular PPC32 Pegasos which uses this driver.
Add #ifdef around the clk API usage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
|
|
The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
|
|
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Ezequiel Garcia
Wilfried Klaebe
Eric W. Biederman
Sebastian Hesselbarth
Florian Fainelli
Jeff Kirsher
Dan Carpenter
Jason Gunthorpe
David S. Miller
Joe Perches
Jingoo Han
Jonas Gorski
Lubomir Rintel
Isaku Yamahata
Arnd Bergmann
Russell King
Andrew Lunn
Simon Baatz
Florian Fainelli
Michael Stapelberg
Phil Sutter
Eric Dumazet
Linus Torvalds
Richard Cochran
David Howells
Danny Kukawka
Pradeep A Dalvi