| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit f85846bbf43de38fb2c89fe7d2a085608c4eb25a ]
Time synchronization was not properly enabled on non-MSI-X platforms.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: James McLaughlin <james.mclaughlin@qsc.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 373e2829e7c2e1e606503cdb5c97749f512a4be9 ]
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 691bd4d7761992914a0e83c27a4ce57d01474cda ]
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading")
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b79959510e6612d80f8d86022e0cb44eee6f4a2 ]
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde61f ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c6bc9e5ce5d37cb3e6b552f41b92a193db1806ab ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: c9a11c23ceb6 ("igc: Add netdev")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56ea7ed103b46970e171eb1c95916f393d64eeff ]
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igc_poll() runs
while the controller is being reset this can lead to the driver try to
free a skb that was already freed.
Log message:
[ 101.525242] refcount_t: underflow; use-after-free.
[ 101.525251] WARNING: CPU: 1 PID: 646 at lib/refcount.c:28 refcount_warn_saturate+0xab/0xf0
[ 101.525259] Modules linked in: sch_etf(E) sch_mqprio(E) rfkill(E) intel_rapl_msr(E) intel_rapl_common(E)
x86_pkg_temp_thermal(E) intel_powerclamp(E) coretemp(E) binfmt_misc(E) kvm_intel(E) kvm(E) irqbypass(E) crc32_pclmul(E)
ghash_clmulni_intel(E) aesni_intel(E) mei_wdt(E) libaes(E) crypto_simd(E) cryptd(E) glue_helper(E) snd_hda_codec_hdmi(E)
rapl(E) intel_cstate(E) snd_hda_intel(E) snd_intel_dspcfg(E) sg(E) soundwire_intel(E) intel_uncore(E) at24(E)
soundwire_generic_allocation(E) iTCO_wdt(E) soundwire_cadence(E) intel_pmc_bxt(E) serio_raw(E) snd_hda_codec(E)
iTCO_vendor_support(E) watchdog(E) snd_hda_core(E) snd_hwdep(E) snd_soc_core(E) snd_compress(E) snd_pcsp(E)
soundwire_bus(E) snd_pcm(E) evdev(E) snd_timer(E) mei_me(E) snd(E) soundcore(E) mei(E) configfs(E) ip_tables(E) x_tables(E)
autofs4(E) ext4(E) crc32c_generic(E) crc16(E) mbcache(E) jbd2(E) sd_mod(E) t10_pi(E) crc_t10dif(E) crct10dif_generic(E)
i915(E) ahci(E) libahci(E) ehci_pci(E) igb(E) xhci_pci(E) ehci_hcd(E)
[ 101.525303] drm_kms_helper(E) dca(E) xhci_hcd(E) libata(E) crct10dif_pclmul(E) cec(E) crct10dif_common(E) tsn(E) igc(E)
e1000e(E) ptp(E) i2c_i801(E) crc32c_intel(E) psmouse(E) i2c_algo_bit(E) i2c_smbus(E) scsi_mod(E) lpc_ich(E) pps_core(E)
usbcore(E) drm(E) button(E) video(E)
[ 101.525318] CPU: 1 PID: 646 Comm: irq/37-enp7s0-T Tainted: G E 5.10.30-rt37-tsn1-rt-ipipe #ipipe
[ 101.525320] Hardware name: SIEMENS AG SIMATIC IPC427D/A5E31233588, BIOS V17.02.09 03/31/2017
[ 101.525322] RIP: 0010:refcount_warn_saturate+0xab/0xf0
[ 101.525325] Code: 05 31 48 44 01 01 e8 f0 c6 42 00 0f 0b c3 80 3d 1f 48 44 01 00 75 90 48 c7 c7 78 a8 f3 a6 c6 05 0f 48
44 01 01 e8 d1 c6 42 00 <0f> 0b c3 80 3d fe 47 44 01 00 0f 85 6d ff ff ff 48 c7 c7 d0 a8 f3
[ 101.525327] RSP: 0018:ffffbdedc0917cb8 EFLAGS: 00010286
[ 101.525329] RAX: 0000000000000000 RBX: ffff98fd6becbf40 RCX: 0000000000000001
[ 101.525330] RDX: 0000000000000001 RSI: ffffffffa6f2700c RDI: 00000000ffffffff
[ 101.525332] RBP: ffff98fd6becc14c R08: ffffffffa7463d00 R09: ffffbdedc0917c50
[ 101.525333] R10: ffffffffa74c3578 R11: 0000000000000034 R12: 00000000ffffff00
[ 101.525335] R13: ffff98fd6b0b1000 R14: 0000000000000039 R15: ffff98fd6be35c40
[ 101.525337] FS: 0000000000000000(0000) GS:ffff98fd6e240000(0000) knlGS:0000000000000000
[ 101.525339] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 101.525341] CR2: 00007f34135a3a70 CR3: 0000000150210003 CR4: 00000000001706e0
[ 101.525343] Call Trace:
[ 101.525346] sock_wfree+0x9c/0xa0
[ 101.525353] unix_destruct_scm+0x7b/0xa0
[ 101.525358] skb_release_head_state+0x40/0x90
[ 101.525362] skb_release_all+0xe/0x30
[ 101.525364] napi_consume_skb+0x57/0x160
[ 101.525367] igc_poll+0xb7/0xc80 [igc]
[ 101.525376] ? sched_clock+0x5/0x10
[ 101.525381] ? sched_clock_cpu+0xe/0x100
[ 101.525385] net_rx_action+0x14c/0x410
[ 101.525388] __do_softirq+0xe9/0x2f4
[ 101.525391] __local_bh_enable_ip+0xe3/0x110
[ 101.525395] ? irq_finalize_oneshot.part.47+0xe0/0xe0
[ 101.525398] irq_forced_thread_fn+0x6a/0x80
[ 101.525401] irq_thread+0xe8/0x180
[ 101.525403] ? wake_threads_waitq+0x30/0x30
[ 101.525406] ? irq_thread_check_affinity+0xd0/0xd0
[ 101.525408] kthread+0x183/0x1a0
[ 101.525412] ? kthread_park+0x80/0x80
[ 101.525415] ret_from_fork+0x22/0x30
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings")
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6da262378c99b17b1a1ac2e42aa65acc1bd471c7 ]
This commit applies to the igc_reset_task the same changes that
were applied to the igb driver in commit 024a8168b749 ("igb:
reinit_locked() should be called with rtnl_lock")
and fix possible race in reset subtask.
Fixes: 0507ef8a0372 ("igc: Add transmit and receive fastpath and interrupt handlers")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
'igc_update_stats()' was not updating 'netdev->stats', so the returned
statistics, for example, requested by:
$ ip -s link show dev enp3s0
were not being updated and were always zero.
Fix by returning a set of statistics that are actually being
updated (adapter->stats64).
Fixes: c9a11c23ceb6 ("igc: Add netdev")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we set the BASET registers of i225 with a base_time in the
future, i225 will "hold" all packets until that base_time is reached,
causing a lot of TX Hangs.
As this behaviour seems contrary to the expectations of the IEEE
802.1Q standard (section 8.6.9, especially 8.6.9.4.5), let's start by
rejecting these types of schedules. If this is too limiting, we can
for example, setup a timer to configure the BASET registers closer to
the start time, only blocking the packets for a "short" while.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Many TSN features depend on the internal PTP clock, so the internal
PTP jumping when the adapter is reset can cause problems, usually in
the form of "TX Hangs" warnings in the driver.
The solution is to save the PTP time before a reset and restore it
after the reset is done. The value of the PTP time is saved before a
reset and we use the difference from CLOCK_MONOTONIC from reset time
to now, to correct what's going to be the new PTP time.
This is heavily inspired by commit bf4bf09bdd91 ("i40e: save PTP time
before a device reset").
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Completion to commit 900d1e8b346b ("igc: Add LPI counters")
LPI counters exposed by statistics update method.
A EEE TX LPI counter reflect the transmitter entries EEE (IEEE 802.3az)
into the LPI state. A EEE RX LPI counter reflect the receiver link
partner entries into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
i225 advanced receive descriptor doesn't have the following extend error
bits: CE, SE, SEQ, CXE. In addition to that, the bit TCPE is called L4E
in the datasheet.
Clean up the code accordingly, and get rid of the macro
IGC_RXDEXT_ERR_FRAME_ERR_MASK since it doesn't make much sense anymore.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add new device ID's for the next step of the silicon and
reflect i221 and i226 parts
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Right now, igc_ptp_reset() is called from igc_reset(), which is called
from igc_probe() before igc_ptp_init() has a chance to run. It is
detected as an attempt to use an spinlock without registering its key
first. See log below.
To avoid this problem, simplify the initialization: igc_ptp_init() is
only called from igc_probe(), and igc_ptp_reset() is only called from
igc_reset().
[ 2.736332] INFO: trying to register non-static key.
[ 2.736902] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input10
[ 2.737513] the code is fine but needs lockdep annotation.
[ 2.737513] turning off the locking correctness validator.
[ 2.737515] CPU: 8 PID: 239 Comm: systemd-udevd Tainted: G E 5.8.0-rc7+ #13
[ 2.737515] Hardware name: Gigabyte Technology Co., Ltd. Z390 AORUS ULTRA/Z390 AORUS ULTRA-CF, BIOS F7 03/14/2019
[ 2.737516] Call Trace:
[ 2.737521] dump_stack+0x78/0xa0
[ 2.737524] register_lock_class+0x6b1/0x6f0
[ 2.737526] ? lockdep_hardirqs_on_prepare+0xca/0x160
[ 2.739177] ? _raw_spin_unlock_irq+0x24/0x50
[ 2.739179] ? trace_hardirqs_on+0x1c/0xf0
[ 2.740820] __lock_acquire+0x56/0x1ff0
[ 2.740823] ? __schedule+0x30c/0x970
[ 2.740825] lock_acquire+0x97/0x3e0
[ 2.740830] ? igc_ptp_reset+0x35/0xf0 [igc]
[ 2.740833] ? schedule_hrtimeout_range_clock+0xb7/0x120
[ 2.742507] _raw_spin_lock_irqsave+0x3a/0x50
[ 2.742512] ? igc_ptp_reset+0x35/0xf0 [igc]
[ 2.742515] igc_ptp_reset+0x35/0xf0 [igc]
[ 2.742519] igc_reset+0x96/0xd0 [igc]
[ 2.744148] igc_probe+0x68f/0x7d0 [igc]
[ 2.745796] local_pci_probe+0x3d/0x70
[ 2.745799] pci_device_probe+0xd1/0x190
[ 2.745802] really_probe+0x15a/0x3f0
[ 2.759936] driver_probe_device+0xe1/0x150
[ 2.759937] device_driver_attach+0xa8/0xb0
[ 2.761786] __driver_attach+0x89/0x150
[ 2.761786] ? device_driver_attach+0xb0/0xb0
[ 2.761787] ? device_driver_attach+0xb0/0xb0
[ 2.761788] bus_for_each_dev+0x66/0x90
[ 2.765012] bus_add_driver+0x12e/0x1f0
[ 2.765716] driver_register+0x8b/0xe0
[ 2.766418] ? 0xffffffffc0230000
[ 2.767119] do_one_initcall+0x5a/0x310
[ 2.767826] ? kmem_cache_alloc_trace+0xe9/0x200
[ 2.768528] do_init_module+0x5c/0x260
[ 2.769206] __do_sys_finit_module+0x93/0xe0
[ 2.770048] do_syscall_64+0x46/0xa0
[ 2.770716] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2.771396] RIP: 0033:0x7f83534589e0
[ 2.772073] Code: 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 2e 2e 2e 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 80 24 0d 00 f7 d8 64 89 01 48
[ 2.772074] RSP: 002b:00007ffd31d0ed18 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 2.774854] RAX: ffffffffffffffda RBX: 000055d52816aba0 RCX: 00007f83534589e0
[ 2.774855] RDX: 0000000000000000 RSI: 00007f83535b982f RDI: 0000000000000006
[ 2.774855] RBP: 00007ffd31d0ed60 R08: 0000000000000000 R09: 00007ffd31d0ed30
[ 2.774856] R10: 0000000000000006 R11: 0000000000000246 R12: 0000000000000000
[ 2.774856] R13: 0000000000020000 R14: 00007f83535b982f R15: 000055d527f5e120
Fixes: 5f2958052c58 ("igc: Add basic skeleton for PTP")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
PHY of the i225 device support only copper mode.
There is no point to check media type in the
igc_power_up_link() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the implementation of igc_power_down_link()
method was just calling igc_power_down_phy_copper_base()
method.
We can just call igc_power_down_phy_copper_base()
method directly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
TCP segmentation TX context fail counter is not
applicable for i225 devices.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown<aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Differently from I210, I225 doesn't report Rx timestamps via the TS bit
Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are
reported in the packet buffer only, which is implemented by igc_ptp_rx_
pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code
related to it, copied from igb driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
IEEE802.3az-2010 Energy Efficient Ethernet has been
approved as standard (September 2010) and the driver
can enable and disable it via ethtool.
Disable the feature by default on parts which support it.
Add enable/disable eee options.
tx-lpi, tx-timer and advertise not supported yet.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During igc_down(), we call igc_nfc_rule_exit() which traverse the NFC
rule list disabling filters one by one. Later on in igc_down() flow
we issue an hardware reset which also clear all filters. Since we
already reset the hardware, we don't actually need to disable each
filter manually. In order to simplify the code, this patch removes
igc_nfc_rule() altogether.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes adapter->nfc_rule_lock type from spin_lock to mutex
so we avoid unnecessary busy waiting on lock contention.
A closer look at the execution context of NFC rule API users shows that
all of them run in process context. The API users are: ethtool ops,
igc_configure(), called when interface is brought up by user or reset
workequeue thread, igc_down(), called when interface is brought down,
and igc_remove(), called when driver is unloaded.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
None of igc_disable_nfc_rule() callers actually check its returning
value. A closer look at why this function would fail shows that the
only situation is when we try to delete an Ethertype or MAC filter that
doesn't exist.
That situation is very unlikely so we can change igc_del_etype_filter()
and igc_del_mac_filter() logic to "if the filter doesn't exist, we are
done", and keep the logic in igc_disable_nfc_rule() callers simple.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If we have RFC rules in adapter->nfc_rule_list when the IGC driver
is unloaded, all rules are leaked. This patch fixes the issue by
introducing the helper igc_flush_nfc_rules() and calling it in
igc_remove(). It also updates igc_set_features() so is reuses the
new helper instead of re-implementing it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Current implementation of igc_ethtool_update_nfc_rule() is a bit
convoluted since it handles too many things: rule lookup, deletion
and addition. This patch breaks it into three functions so we simplify
the code and improve code reuse.
Code related to rule lookup is refactored out to a new function called
igc_get_nfc_rule().
Code related to rule addition is refactored out to a new function called
igc_add_nfc_rule(). This function enables the rule in hardware and adds
it to the adapter's list.
Code related to rule deletion is refactored out to a new function called
igc_del_nfc_rule(). This function disables the rule in hardware, removes
it from adapter's list, and deletes it.
As a byproduct of this refactoring, igc_enable_nfc_rule() and
igc_disable_nfc_rule() are moved to igc_main.c since they are not used
in igc_ethtool.c anymore, and igc_restore_nfc_rules() and igc_nfc_rule_
exit() are moved around to avoid forward declaration.
Also, since this patch already touches igc_ethtool_get_nfc_rule(), it
takes the opportunity to remove the 'match_flags' check. Empty flags
are not allowed to be added so no need to check that.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When network interface is brought up, the driver re-enables the NFC
rules previously configured. However, this is done in reverse order
the rules were added and hardware filters are configured differently.
For example, consider the following rules:
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:AA queue 0
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:BB queue 1
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:CC queue 2
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:DD queue 3
RAL/RAH registers are configure so filter index 1 has address ending
with AA, filter index 2 has address ending in BB, and so on.
If we bring the interface down and up again, RAL/RAH registers are
configured so filter index 1 has address ending in DD, filter index 2
has CC, and so on. IOW, in reverse order we had before bringing the
interface down.
This issue can be fixed by traversing adapter->nfc_rule_list in
backwards when restoring the rules. Since hlist doesn't support
backwards traversal, this patch replaces it by list_head and fixes
igc_restore_nfc_rules() accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Multicast MAC addresses are valid address for NFC rules but
igc_add_mac_filter() is currently rejecting them. In fact, the I225
controller doesn't impose any constraint on the address value so this
patch gets rid of the address validation check in MAC filter APIs.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Network Flow Classification (NFC) support code from IGC driver uses
terms such as 'rule', 'filter', 'entry', 'input' interchangeably when
referring to NFC rules, making it harder to follow the code. This patch
renames IGC's internal APIs, structs, and variables so we stick with the
term 'rule' since this is the term used in ethtool APIs. It also removes
some not applicable comments along the way. No functionality is changed
by this patch.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds the prefix 'igc_ethtool_' to all functions defined in
igc_ethtool.c so they align with the name convention already followed by
other parts of the driver (e.g. igc_tsn, igc_ptp). Also, this avoids
some name clashing with functions added to igc_main.c by upcoming
patches in this series. No functionality is changed by this patch, just
function renaming.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The local function igc_max_channels() is a pointless wrapper around
igc_get_max_rss_queues(). This patch removes it and updates the callers
accordingly. It also does some cleanup on igc_get_max_rss_queues().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch extends MAC address filter internal APIs igc_add_mac_filter()
and igc_del_mac_filter(), as well as local helpers, to support filters
based on source address.
A new parameters 'type' is added to the APIs to indicate if the filter
type is source or destination. In case it is source type, the RAH
register is configured accordingly in igc_set_mac_filter_hw().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In igc_adapter we keep a sort of shadow copy of RAL and RAH registers.
There is not much benefit in keeping it, at the cost of maintainability,
since adding/removing MAC address filters is not hot path, and we
already keep filters information in adapter->nfc_filter_list for cleanup
and restoration purposes.
So in order to simplify the MAC address filtering code and prepare it
for source address support, this patch removes the mac_table from
igc_adapter.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
MAC address filters based on source address are not currently supported
by the IGC driver. Despite of that, the driver have some dangling code
to handle it, inherited from IGB driver. This patch removes that code to
prepare for a follow up patch that adds proper source MAC address filter
support.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The whole ethertype filtering code is implemented in igc_ethtool.c and
mixes logic from ethtool and core parts. This patch refactors it so core
logic is moved to igc_main.c, aligning the ethertype filtering code
organization with the rest of the filtering code from the driver (MAC
address and VLAN priority).
Besides moving code to igc_main.c, this patch also does some minor
improvements to the code. Below are some highlights.
In case all filters are already in use and the user tries to add another
filter, we return -ENOSPC instead of -EINVAL so a more meaningful error
code is provided. This also aligns with the behavior implemented in MAC
address filtering code.
With this code refactoring, 'etype_bitmap' array in struct igc_adapter
and 'etype_reg_index' in struct igc_nfc_filter are not needed anymore
and are removed.
Log messages are added to help debugging the ethertype filtering code.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The whole VLAN priority filtering code is implemented in igc_ethtool.c
and mixes logic from ethtool and core parts. This patch refactors it so
core logic is moved to igc_main.c, aligning the VLAN priority filtering
code organization with the MAC address filtering code.
This patch also takes the opportunity to add some log messages to ease
debugging.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igc driver has leftovers from the previous device that supported
Virtualization. This can be found in the function IGC_REMOVED which
became obsolete, and can be removed.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Introduced igc_diag.c and igc_diag.h, these files have the
diagnostics functionality of igc driver. For the time being
these files are being used by ethtool self-test callbacks.
Which mean that eeprom, registers and link self-tests for
ethtool were implemented.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In igc_main.c we print log messages using both dev_* and netdev_*
helpers, generating inconsistent output. Since this is a network device
driver, we should preferably use netdev_* helpers because they append
the interface name to the message, helping making sense out of the logs.
This patch converts all dev_* calls to netdev_*. There is only two
exceptions:
1) calls wihtin igc_probe (net_device has not been registered yet)
2) calls in igc_init_module (module initialization).
It also takes this opportunity to improve some messages.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
James McLaughlin
Sasha Neftin
Toshiki Nishioka
Aaron Ma
Christophe JAILLET
Vinicius Costa Gomes
Sebastian Andrzej Siewior
Andre Guedes
Jesse Brandeburg
Tariq Toukan
Jeff Kirsher
Linus Torvalds
Vitaly Lifshits