| Age | Commit message (Collapse) | Author |
|---|
|
commit d59e267912cd90b0adf33b4659050d831e746317 upstream.
READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 27d461333459d282ffa4a2bdb6b215a59d493a8f upstream.
In i40e_setup_macvlans if i40e_setup_channel fails the allocated memory
for ch should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b3873a5be757b44d51af542a50a6f2a3b6f95284 upstream.
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).
2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).
4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com
[PG: note async_xmit ---> wakeup rename in mainline 9116e5e2b1ff.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 998e5166e604fd37afe94352f7b8c2d816b11049 upstream.
Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN/ITR0 registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a7542b87607560d0b89e7ff81d870bd6ff8835cb upstream.
While testing VF spawn/destroy the following panic occurred.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000029
[...]
Workqueue: i40e i40e_service_task [i40e]
RIP: 0010:i40e_sync_vsi_filters+0x6fd/0xc60 [i40e]
[...]
Call Trace:
? __switch_to_asm+0x35/0x70
? __switch_to_asm+0x41/0x70
? __switch_to_asm+0x35/0x70
? _cond_resched+0x15/0x30
i40e_sync_filters_subtask+0x56/0x70 [i40e]
i40e_service_task+0x382/0x11b0 [i40e]
? __switch_to_asm+0x41/0x70
? __switch_to_asm+0x41/0x70
process_one_work+0x1a7/0x3b0
worker_thread+0x30/0x390
? create_worker+0x1a0/0x1a0
kthread+0x112/0x130
? kthread_bind+0x30/0x30
ret_from_fork+0x35/0x40
Investigation revealed a race where pf->vf[vsi->vf_id].trusted may get
accessed by the watchdog via i40e_sync_filters_subtask() although
i40e_free_vfs() already free'd pf->vf.
To avoid this the call to i40e_sync_vsi_filters() in
i40e_sync_filters_subtask() needs to be guarded by __I40E_VF_DISABLE,
which is also used by i40e_free_vfs().
Note: put the __I40E_VF_DISABLE check after the
__I40E_MACVLAN_SYNC_PENDING check as the latter is more likely to
trigger.
CC: stable@vger.kernel.org
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
New device ids are created to support X710 backplane and SFP+ cards.
This patch adds in i40e driver support for 2.5GbaseT and 5GbaseT speed.
It's implemented by checking I40E_CAP_PHY_TYPE_2_5GBASE_T,
I40E_CAP_PHY_TYPE_5GBASE_T bits from f/w and setting corresponding bits
in ethtool link ksettings supported and advertising masks.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a bug where changing VLAN to 0 was not set until VF
restart.
Now we are setting pvid info to 0 when we have to change VLAN to 0.
Without this change when VF VLAN was changed to 0 nothing happened until
VF restart. For changing to VLAN different than 0 it worked correctly.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
New device ids are created to support X710/XXV710 N3000 cards.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.
These additional AQ commands are part of the interface used by
the NVMUpdate tool. The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands. The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Printing each devices PCI vendor and device ID has the advantage of
easily revealing what hardware we're dealing with exactly. It's no
longer necessary to match the PCI bus information to the lspci output.
Helps with bug reports where no lspci output is available.
Output before
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0
and after
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0 [8086:1572] [8086:0004]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Just bumping the version number appropriately.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
TX MDD events reported on the PF are the result of the
PF misconfiguring a descriptor and not because of "bad actions"
by anything else. No need to reset now because if it
results in a Tx hang, the Tx hang check will take care of it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the driver behavior when detecting a VF MDD event.
It now disables the VF after one event, which indicates a hw detected
problem in the VF. Before this change, the PF would allow a couple of
events before doing the reset.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Added the API version in the error message for clarity.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Removed misleading messages when untrusted VF tries to
add more addresses than NIC limit
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Modify the i40e_init_dcb to return the correct error when LLDP or DCBX
is not in operational state.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the case where PTP is running on the hardware clock, but the kernel
system time is not being synced, a device reset can mess up the clock
time.
This occurs because we reset the clock time based on the kernel time
every reset. This causes us to potentially completely reset the PTP
time, and can cause unexpected behavior in programs like ptp4l.
Avoid this by saving the PTP time prior to device reset, and then
restoring using that time after the reset.
Directly restoring the PTP time we saved isn't perfect, because time
should have continued running, but the clock will essentially be stopped
during the reset. This is still better than the current solution of
assuming that the PTP HW clock is synced to the CLOCK_REALTIME.
We can do even better, by saving the ktime and calculating
a differential, using ktime_get(). This is based on CLOCK_MONOTONIC, and
allows us to get a fairly precise measure of the time difference between
saving and restoring the time.
Using this, we can update the saved PTP time, and use that as the value
to write to the hardware clock registers. This, of course is not perfect.
However, it does help ensure that the PTP time is restored as close as
feasible to the time it should have been if the reset had not occurred.
During device initialization, continue using the system time as the
source for the creation of the PTP clock, since this is the best known
current time source at driver load.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Modifying the VLAN stripping options when a port VLAN is configured
will break traffic for the VSI, and conceptually doesn't make sense,
so don't allow this.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch introduces DDP (Dynamic Device Personalization) which allows
loading profiles that change the way internal parser interprets processed
frames. To load DDP profiles it utilizes ethtool flash feature. The files
with recipes must be located in /var/lib/firmware directory. Afterwards
the recipe can be loaded by invoking:
ethtool -f <if_name> <file_name> 100
ethtool -f <if_name> - 100
See further details of this feature in the i40e documentation, or
visit
https://www.intel.com/content/www/us/en/architecture-and-technology/ethernet/dynamic-device-personalization-brief.html
The driver shall verify DDP profile can be loaded in accordance with
the rules:
* Package with Group ID 0 are exclusive and can only be loaded the first.
* Packages with Group ID 0x01-0xFE can only be loaded simultaneously
with the packages from the same group.
* Packages with Group ID 0xFF are compatible with all other packages.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Added a new local variable in the i40e_setup_tc function named
old_queue_pairs so num_queue_pairs can be restored to the correct
value in case configuring queue channels fails. Additionally, moved
the exit label in the i40e_setup_tc function so the if (need_reset)
block can be executed.
Also, fixed data packing in the i40e_setup_tc function.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit f3fef2b6e1cc ("i40e: Remove umem from VSI") a regression was
introduced; When the VSI was reset, the setup code would try to enable
AF_XDP ZC unconditionally (as long as there was a umem placed in the
netdev._rx struct). Here, we add a bitmap to the VSI that tracks if a
certain queue pair has been "zero-copy enabled" via the ndo_bpf. The
bitmap is used in i40e_xsk_umem, and enables zero-copy if and only if
XDP is enabled, the corresponding qid in the bitmap is set and the
umem is non-NULL.
Fixes: f3fef2b6e1cc ("i40e: Remove umem from VSI")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e_xsk_umem function was explicitly inlined in i40e.h. There is
no reason for that, so move it to i40e_main.c instead.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver clears the XDP xmit ring due to re-configuration or
teardown, in-progress ndo_xdp_xmit must be taken into consideration.
The ndo_xdp_xmit function is typically called from a NAPI context that
the driver does not control. Therefore, we must be careful not to
clear the XDP ring, while the call is on-going. This patch adds a
synchronize_rcu() to wait for napi(s) (preempt-disable regions and
softirqs), prior clearing the queue. Further, the __I40E_CONFIG_BUSY
flag is checked in the ndo_xdp_xmit implementation to avoid touching
the XDP xmit queue during re-configuration.
Fixes: d9314c474d4f ("i40e: add support for XDP_REDIRECT")
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit c9b47cc1fabc ("xsk: fix bug when trying to use both copy and
zero-copy on one queue id") moved the umem query code to the AF_XDP
core, and therefore removed the need to query the netdevice for a
umem.
This patch removes XDP_QUERY_XSK_UMEM and all code that implement that
behavior, which is just dead code.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.
To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.
This introduces two new interfaces:
bool flow_rule_match_key(rule, dissector_id)
that returns true if a given matching key is set on, and:
flow_rule_match_XYZ(rule, &match);
To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several statements that have incorrect levels of indentation,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Convert spaces to tabs to get correct alignment.
Found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for setting/getting FEC configuration
using ethtool options:
set/show-priv-flags rs-fec/base-r-fec
set/show-fec off/rs/baser/auto for kernels version >= 4.14
Signed-off-by: Damian Dybek <damian.dybek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Limiting RSS queues number to online CPUs number in order to
avoid issues with creating misconfigured RSS queues.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-12-20
This series contains updates to e100, igb, ixgbe, i40e and ice drivers.
I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics. This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.
Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.
Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.
YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.
Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.
Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.
Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.
Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in. This was due to the
driver not setting PME during runtime suspend.
Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Out of bound read reported by KASan.
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca0c ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If a TX hang occurs, we attempt to recover by incrementally resetting.
If we're starved for CPU time, it's possible the reset doesn't actually
complete (or even fire) before another tx_timeout fires causing us to
fly through the different resets without actually doing them.
This adds a bit to set and check if a timeout recovery is already
pending and, if so, bail out of tx_timeout. The bit will get cleared at
the end of i40e_rebuild when reset is complete.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch allows disabling FW LLDP agent on X722 devices.
It also changes a source of information for this feature from
pf->hw_features to pf->hw.flags which are set in i40e_init_adminq.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The version numbers have not been kept up to date and this is
an effort to ammend that.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using strncpy allows destination buffer to be not null terminated
after the copying takes place. strlcpy ensures that's not the
case by explicitly setting last element in the buffer as '\0'.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC
occurs prior to the initial setup of the local hw_features variable.
This means the features are set as user-changeable, but are not set in
the currently active feature list. This results in the features being
disabled at the driver's initial load.
Move the assignment after the initial assignment of hw_features, and
assign to the local variable. This ensures that NETIF_F_NTUPLE and
NETIF_F_HW_TC are marked as user-changeable, and also enables them by
default when the driver loads.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit bacd75cfac8a ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.
Fix this by adding back the missing feature flags.
For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa4a
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.
NETIF_F_GSO_IPXIP6 was added in commit bf2d1df39502 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
|
Ciara Loftus
Navid Emamdoost
Maxim Mikityanskiy
Nicholas Nunley
Stefan Assmann
Aleksandr Loktionov
Grzegorz Siwik
Alice Michael
Carolyn Wyborny
Adam Ludkiewicz
Chinh T Cao
Jacob Keller
Björn Töpel
David S. Miller
Magnus Karlsson
Jan Sokolowski
Pablo Neira Ayuso
Colin Ian King
Julia Lawall
Damian Dybek
Petr Machata
Luis Chamberlain
Konstantin Khorenko
Lihong Yang
Alan Brady
Patryk Małek
Lance Roy
Linus Torvalds