| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 16b55b1f2269962fb6b5154b8bf43f37c9a96637 ]
When an EEH error is encountered by a PCI adapter, the EEH driver
modifies the PCI channel's state as shown below:
enum {
/* I/O channel is in normal state */
pci_channel_io_normal = (__force pci_channel_state_t) 1,
/* I/O to channel is blocked */
pci_channel_io_frozen = (__force pci_channel_state_t) 2,
/* PCI card is dead */
pci_channel_io_perm_failure = (__force pci_channel_state_t) 3,
};
If the same EEH error then causes the tg3 driver's transmit timeout
logic to execute, the tg3_tx_timeout() function schedules a reset
task via tg3_reset_task_schedule(), which may cause a race condition
between the tg3 and EEH driver as both attempt to recover the HW via
a reset action.
EEH driver gets error event
--> eeh_set_channel_state()
and set device to one of
error state above scheduler: tg3_reset_task() get
returned error from tg3_init_hw()
--> dev_close() shuts down the interface
tg3_io_slot_reset() and
tg3_io_resume() fail to
reset/resume the device
To resolve this issue, we avoid the race condition by checking the PCI
channel state in the tg3_reset_task() function and skip the tg3 driver
initiated reset when the PCI channel is not in the normal state. (The
driver has no access to tg3 device registers at this point and cannot
even complete the reset task successfully without external assistance.)
We'll leave the reset procedure to be managed by the EEH driver which
calls the tg3_io_error_detected(), tg3_io_slot_reset() and
tg3_io_resume() functions as appropriate.
Adding the same checking in tg3_dump_state() to avoid dumping all
device registers when the PCI channel is not in the normal state.
Signed-off-by: Thinh Tran <thinhtr@linux.vnet.ibm.com>
Tested-by: Venkata Sai Duggi <venkata.sai.duggi@ibm.com>
Reviewed-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201001911.656-1-thinhtr@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 17dd5efe5f36a96bd78012594fabe21efb01186b ]
tg3_tso_bug() drops a packet if it cannot be segmented for any reason.
The number of discarded frames should be incremented accordingly.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20231113182350.37472-2-alexey.pakhunov@spacex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 907d1bdb8b2cc0357d03a1c34d2a08d9943760b1 ]
This change moves [rt]x_dropped counters to tg3_napi so that they can be
updated by a single writer, race-free.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231113182350.37472-1-alexey.pakhunov@spacex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fc3bc7643341dc5be7d269f3d3dbe441d8d7ac3 ]
Dell R650xs servers hangs on reboot if tg3 driver calls
tg3_power_down.
This happens only if network adapters (BCM5720 for R650xs) were
initialized using SNP (e.g. by booting ipxe.efi).
The actual problem is on Dell side, but this fix allows servers
to come back alive after reboot.
Signed-off-by: George Shuklin <george.shuklin@gmail.com>
Fixes: 2ca1c94ce0b6 ("tg3: Disable tg3 device on system reboot to avoid triggering AER")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231103115029.83273-1-george.shuklin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 046f753da6143ee16452966915087ec8b0de3c70 ]
Fixes a bug where on the M1 mac mini initramfs-tools fails to
include the necessary firmware into the initrd.
Fixes: c4dab50697ff ("tg3: Download 57766 EEE service patch firmware")
Signed-off-by: Tobias Heider <me@tobhe.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/ZJt7LKzjdz8+dClx@tobhe.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c4ca03bd890566d873e3593b32d034bf2f5a087 ]
During EEH error injection testing, a deadlock was encountered in the tg3
driver when tg3_io_error_detected() was attempting to cancel outstanding
reset tasks:
crash> foreach UN bt
...
PID: 159 TASK: c0000000067c6000 CPU: 8 COMMAND: "eehd"
...
#5 [c00000000681f990] __cancel_work_timer at c00000000019fd18
#6 [c00000000681fa30] tg3_io_error_detected at c00800000295f098 [tg3]
#7 [c00000000681faf0] eeh_report_error at c00000000004e25c
...
PID: 290 TASK: c000000036e5f800 CPU: 6 COMMAND: "kworker/6:1"
...
#4 [c00000003721fbc0] rtnl_lock at c000000000c940d8
#5 [c00000003721fbe0] tg3_reset_task at c008000002969358 [tg3]
#6 [c00000003721fc60] process_one_work at c00000000019e5c4
...
PID: 296 TASK: c000000037a65800 CPU: 21 COMMAND: "kworker/21:1"
...
#4 [c000000037247bc0] rtnl_lock at c000000000c940d8
#5 [c000000037247be0] tg3_reset_task at c008000002969358 [tg3]
#6 [c000000037247c60] process_one_work at c00000000019e5c4
...
PID: 655 TASK: c000000036f49000 CPU: 16 COMMAND: "kworker/16:2"
...:1
#4 [c0000000373ebbc0] rtnl_lock at c000000000c940d8
#5 [c0000000373ebbe0] tg3_reset_task at c008000002969358 [tg3]
#6 [c0000000373ebc60] process_one_work at c00000000019e5c4
...
Code inspection shows that both tg3_io_error_detected() and
tg3_reset_task() attempt to acquire the RTNL lock at the beginning of
their code blocks. If tg3_reset_task() should happen to execute between
the times when tg3_io_error_deteced() acquires the RTNL lock and
tg3_reset_task_cancel() is called, a deadlock will occur.
Moving tg3_reset_task_cancel() call earlier within the code block, prior
to acquiring RTNL, prevents this from happening, but also exposes another
deadlock issue where tg3_reset_task() may execute AFTER
tg3_io_error_detected() has executed:
crash> foreach UN bt
PID: 159 TASK: c0000000067d2000 CPU: 9 COMMAND: "eehd"
...
#4 [c000000006867a60] rtnl_lock at c000000000c940d8
#5 [c000000006867a80] tg3_io_slot_reset at c0080000026c2ea8 [tg3]
#6 [c000000006867b00] eeh_report_reset at c00000000004de88
...
PID: 363 TASK: c000000037564000 CPU: 6 COMMAND: "kworker/6:1"
...
#3 [c000000036c1bb70] msleep at c000000000259e6c
#4 [c000000036c1bba0] napi_disable at c000000000c6b848
#5 [c000000036c1bbe0] tg3_reset_task at c0080000026d942c [tg3]
#6 [c000000036c1bc60] process_one_work at c00000000019e5c4
...
This issue can be avoided by aborting tg3_reset_task() if EEH error
recovery is already in progress.
Fixes: db84bf43ef23 ("tg3: tg3_reset_task() needs to use rtnl_lock to synchronize")
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230124185339.225806-1-drc@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2ca1c94ce0b65a2ce7512b718f3d8a0fe6224bca ]
Commit d60cd06331a3 ("PM: ACPI: reboot: Use S5 for reboot") caused a
reboot hang on one Dell servers so the commit was reverted.
Someone managed to collect the AER log and it's caused by MSI:
[ 148.762067] ACPI: Preparing to enter system sleep state S5
[ 148.794638] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 5
[ 148.803731] {1}[Hardware Error]: event severity: recoverable
[ 148.810191] {1}[Hardware Error]: Error 0, type: fatal
[ 148.816088] {1}[Hardware Error]: section_type: PCIe error
[ 148.822391] {1}[Hardware Error]: port_type: 0, PCIe end point
[ 148.829026] {1}[Hardware Error]: version: 3.0
[ 148.834266] {1}[Hardware Error]: command: 0x0006, status: 0x0010
[ 148.841140] {1}[Hardware Error]: device_id: 0000:04:00.0
[ 148.847309] {1}[Hardware Error]: slot: 0
[ 148.852077] {1}[Hardware Error]: secondary_bus: 0x00
[ 148.857876] {1}[Hardware Error]: vendor_id: 0x14e4, device_id: 0x165f
[ 148.865145] {1}[Hardware Error]: class_code: 020000
[ 148.870845] {1}[Hardware Error]: aer_uncor_status: 0x00100000, aer_uncor_mask: 0x00010000
[ 148.879842] {1}[Hardware Error]: aer_uncor_severity: 0x000ef030
[ 148.886575] {1}[Hardware Error]: TLP Header: 40000001 0000030f 90028090 00000000
[ 148.894823] tg3 0000:04:00.0: AER: aer_status: 0x00100000, aer_mask: 0x00010000
[ 148.902795] tg3 0000:04:00.0: AER: [20] UnsupReq (First)
[ 148.910234] tg3 0000:04:00.0: AER: aer_layer=Transaction Layer, aer_agent=Requester ID
[ 148.918806] tg3 0000:04:00.0: AER: aer_uncor_severity: 0x000ef030
[ 148.925558] tg3 0000:04:00.0: AER: TLP Header: 40000001 0000030f 90028090 00000000
The MSI is probably raised by incoming packets, so power down the device
and disable bus mastering to stop the traffic, as user confirmed this
approach works.
In addition to that, be extra safe and cancel reset task if it's running.
Cc: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/all/b8db79e6857c41dab4ef08bdf826ea7c47e3bafc.1615947283.git.josef@toxicpanda.com/
BugLink: https://bugs.launchpad.net/bugs/1917471
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220826002530.1153296-1-kai.heng.feng@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 556699341efa98243e08e34401b3f601da91f5a3 ]
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a2656a211caf35e56afc9425e6e518fa52f7fbc ]
The driver function tg3_io_error_detected() calls napi_disable twice,
without an intervening napi_enable, when the number of EEH errors exceeds
eeh_max_freezes, resulting in an indefinite sleep while holding rtnl_lock.
Add check for pcierr_recovery which skips code already executed for the
"Frozen" state.
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 59663e42199c93d1d7314d1446f6782fc4b1eb81 ]
This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Fix dcache flushing crash in skcipher.
- Add hash finup self-tests.
- Reschedule during speed tests.
Algorithms:
- Remove insecure vmac and replace it with vmac64.
- Add public key verification for DH/ECDH.
Drivers:
- Decrease priority of sha-mb on x86.
- Improve NEON latency/throughput on ARM64.
- Add md5/sha384/sha512/des/3des to inside-secure.
- Support eip197d in inside-secure.
- Only register algorithms supported by the host in virtio.
- Add cts and remove incompatible cts1 from ccree.
- Add hisilicon SEC security accelerator driver.
- Replace msm hwrng driver with qcom pseudo rng driver.
Misc:
- Centralize CRC polynomials"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (121 commits)
crypto: arm64/ghash-ce - implement 4-way aggregation
crypto: arm64/ghash-ce - replace NEON yield check with block limit
crypto: hisilicon - sec_send_request() can be static
lib/mpi: remove redundant variable esign
crypto: arm64/aes-ce-gcm - don't reload key schedule if avoidable
crypto: arm64/aes-ce-gcm - implement 2-way aggregation
crypto: arm64/aes-ce-gcm - operate on two input blocks at a time
crypto: dh - make crypto_dh_encode_key() make robust
crypto: dh - fix calculating encoded key size
crypto: ccp - Check for NULL PSP pointer at module unload
crypto: arm/chacha20 - always use vrev for 16-bit rotates
crypto: ccree - allow bigger than sector XTS op
crypto: ccree - zero all of request ctx before use
crypto: ccree - remove cipher ivgen left overs
crypto: ccree - drop useless type flag during reg
crypto: ablkcipher - fix crash flushing dcache in error path
crypto: blkcipher - fix crash flushing dcache in error path
crypto: skcipher - fix crash flushing dcache in error path
crypto: skcipher - remove unnecessary setting of walk->nbytes
crypto: scatterwalk - remove scatterwalk_samebuf()
...
|
|
Merge mainline to pick up c7513c2a2714 ("crypto/arm64: aes-ce-gcm -
add missing kernel_neon_begin/end pair").
|
|
Do not define again the polynomial but use header with existing define.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
All conflicts were trivial overlapping changes, so reasonably
easy to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a * b, gfp)
as well as handling cases of:
kzalloc(a * b * c, gfp)
with:
kzalloc(array3_size(a, b, c), gfp)
as it's slightly less ugly than:
kzalloc_array(array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
kzalloc(4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
kzalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kzalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
kzalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
- kzalloc
+ kcalloc
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
kzalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
kzalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
kzalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
kzalloc(sizeof(THING) * C2, ...)
|
kzalloc(sizeof(TYPE) * C2, ...)
|
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * E2
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
tg3_free_consistent() calls dma_free_coherent() to free tp->hw_stats
under spinlock and can trigger BUG_ON() in vunmap() because vunmap()
may sleep. Fix it by removing the spinlock and relying on the
TG3_FLAG_INIT_COMPLETE flag to prevent race conditions between
tg3_get_stats64() and tg3_free_consistent(). TG3_FLAG_INIT_COMPLETE
is always cleared under tp->lock before tg3_free_consistent()
and therefore tg3_get_stats64() can safely access tp->hw_stats
under tp->lock if TG3_FLAG_INIT_COMPLETE is set.
Fixes: f5992b72ebe0 ("tg3: Fix race condition in tg3_get_stats64().")
Reported-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The problem was introduced in commit
506b0a395f26 ("[netdrv] tg3: APE heartbeat changes"). The bug occurs
because tp->lock spinlock is held which is obtained in tg3_start
by way of tg3_full_lock(), line 11571. The documentation for usleep_range()
specifically states it cannot be used inside a spinlock.
Fixes: 506b0a395f26 ("[netdrv] tg3: APE heartbeat changes")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for Macronix NVRAM
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.
Casting from unsigned long:
void my_callback(unsigned long data)
{
struct something *ptr = (struct something *)data;
...
}
...
setup_timer(&ptr->my_timer, my_callback, ptr);
and forced object casts:
void my_callback(struct something *ptr)
{
...
}
...
setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);
become:
void my_callback(struct timer_list *t)
{
struct something *ptr = from_timer(ptr, t, my_timer);
...
}
...
timer_setup(&ptr->my_timer, my_callback, 0);
Direct function assignments:
void my_callback(unsigned long data)
{
struct something *ptr = (struct something *)data;
...
}
...
ptr->my_timer.function = my_callback;
have a temporary cast added, along with converting the args:
void my_callback(struct timer_list *t)
{
struct something *ptr = from_timer(ptr, t, my_timer);
...
}
...
ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;
And finally, callbacks without a data assignment:
void my_callback(unsigned long data)
{
...
}
...
setup_timer(&ptr->my_timer, my_callback, 0);
have their argument renamed to verify they're unused during conversion:
void my_callback(struct timer_list *unused)
{
...
}
...
timer_setup(&ptr->my_timer, my_callback, 0);
The conversion is done with the following Coccinelle script:
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/timer_setup.cocci
@fix_address_of@
expression e;
@@
setup_timer(
-&(e)
+&e
, ...)
// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@
(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)
@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@
(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
_E->_timer@_stl.function = _callback;
|
_E->_timer@_stl.function = &_callback;
|
_E->_timer@_stl.function = (_cast_func)_callback;
|
_E->_timer@_stl.function = (_cast_func)&_callback;
|
_E._timer@_stl.function = _callback;
|
_E._timer@_stl.function = &_callback;
|
_E._timer@_stl.function = (_cast_func)_callback;
|
_E._timer@_stl.function = (_cast_func)&_callback;
)
// callback(unsigned long arg)
@change_callback_handle_cast
depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@
void _callback(
-_origtype _origarg
+struct timer_list *t
)
{
(
... when != _origarg
_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle;
... when != _handle
_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle;
... when != _handle
_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
)
}
// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
depends on change_timer_function_usage &&
!change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@
void _callback(
-_origtype _origarg
+struct timer_list *t
)
{
+ _handletype *_origarg = from_timer(_origarg, t, _timer);
+
... when != _origarg
- (_handletype *)_origarg
+ _origarg
... when != _origarg
}
// Avoid already converted callbacks.
@match_callback_converted
depends on change_timer_function_usage &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@
void _callback(struct timer_list *t)
{ ... }
// callback(struct something *handle)
@change_callback_handle_arg
depends on change_timer_function_usage &&
!match_callback_converted &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@
void _callback(
-_handletype *_handle
+struct timer_list *t
)
{
+ _handletype *_handle = from_timer(_handle, t, _timer);
...
}
// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
depends on change_timer_function_usage &&
change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@
void _callback(struct timer_list *t)
{
- _handletype *_handle = from_timer(_handle, t, _timer);
}
// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
depends on change_timer_function_usage &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg &&
!change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@
(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)
// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
depends on change_timer_function_usage &&
(change_callback_handle_cast ||
change_callback_handle_cast_no_arg ||
change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@
(
_E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
;
)
// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
depends on change_timer_function_usage &&
(change_callback_handle_cast ||
change_callback_handle_cast_no_arg ||
change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@
_callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
)
// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@
(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)
@change_callback_unused_data
depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@
void _callback(
-_origtype _origarg
+struct timer_list *unused
)
{
... when != _origarg
}
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tnapi is being initialized and then immediately updated and
hence the initialiation is redundant. Clean up the warning
by moving the declaration and initialization to the inside
of the for-loop.
Cleans up clang scan-build warning:
warning: Value stored to 'tnapi' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_tx() does the normal packet TX completion,
tigon3_dma_hwbug_workaround() and tg3_tso_bug() both need to allocate a
new SKB that is suitable to workaround HW bugs, and finally
tg3_free_rings() is doing ring cleanup. Use dev_consume_skb_any() for
these 3 locations to be SKB drop monitor friendly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now tg3 NIC's stats will be cleared after ifdown/ifup. bond_get_stats traverse
its salves to get statistics,cumulative the increment.If a tg3 NIC is added to
bonding as a slave,ifdown/ifup will cause bonding's stats become tremendous value
(ex.1638.3 PiB) because of negative increment.
Fixes: 92feeabf3f67 ("tg3: Save stats across chip resets")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a Kconfig option: CONFIG_TIGON3_HWMON which allows to build
in/out support for thermal sensors reported by Tigon3 NICs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<linux/sched.h> into <linux/sched/signal.h>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
|
|
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3: min_mtu 60, max_mtu 9000/1500
bnxt: min_mtu 60, max_mtu 9000
bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
duplicated defines from bnx2x_link.c.
bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.
bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
bcm_enet_change_mtu.
b44: min_mtu 60, max_mtu 1500
CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three sets of overlapping changes. Nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
[1.402247] Unable to handle kernel paging request for data at address 0x00001a99
[1.402410] Faulting instruction address: 0xc0000000007e33f8
[1.402450] Oops: Kernel access of bad area, sig: 11 [#1]
[1.402481] SMP NR_CPUS=2048 NUMA PowerNV
[1.402513] Modules linked in:
[1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic #55-Ubuntu
[1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
[1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
[1.402787] REGS: c000001fe4e8b790 TRAP: 0300 Not tainted (4.4.0-36-generic)
[1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 28000422 XER: 20000000
[1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
[1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
[1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a063b1ff ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f370316b ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent commit 087d7a8c9174 "tg3: Fix for diasllow rx coalescing
time to be 0" disallow to set Rx coalescing time to be 0 as this stops
generating interrupts for the incoming packets. I found the zero
Tx coalescing time stops generating interrupts for outgoing packets
as well and fires Tx watchdog later. To avoid this, don't allow to set
Tx coalescing time to 0 and also remove subsequent checks that become
senseless.
Cc: satish.baddipadige@broadcom.com
Cc: siva.kallam@broadcom.com
Cc: michael.chan@broadcom.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:
struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)
Compile tested only.
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.
tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.
This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.
v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Thinh Tran
Alex Pakhunov
George Shuklin
Tobias Heider
David Christensen
Kai-Heng Feng
Michael Chan
Siva Reddy Kallam
Linus Torvalds
Herbert Xu
Krzysztof Kozlowski
David S. Miller
Sanjeev Bansal
Gustavo A. R. Silva
Kees Cook
Joe Perches
Jonathan Toppins
Prashant Sreedharan
Brian King
Allen Pais
Colin Ian King
Florian Fainelli
yuval.shaia@oracle.com
YueHaibing
Ingo Molnar
stephen hemminger
Jarod Wilson
Milton Miller
Philippe Reynes
Ivan Vecera
Satish Baddipadige
Florian Westphal
Arnd Bergmann
Andrew Lunn