Age | Commit message (Collapse) | Author |
|
commit 949fe9b35570361bc6ee2652f89a0561b26eec98 upstream.
When remove the module peek_pci, referencing 'chan' again after
releasing 'dev' will cause UAF.
Fix this by releasing 'dev' later.
The following log reveals it:
[ 35.961814 ] BUG: KASAN: use-after-free in peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.963414 ] Read of size 8 at addr ffff888136998ee8 by task modprobe/5537
[ 35.965513 ] Call Trace:
[ 35.965718 ] dump_stack_lvl+0xa8/0xd1
[ 35.966028 ] print_address_description+0x87/0x3b0
[ 35.966420 ] kasan_report+0x172/0x1c0
[ 35.966725 ] ? peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.967137 ] ? trace_irq_enable_rcuidle+0x10/0x170
[ 35.967529 ] ? peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.967945 ] __asan_report_load8_noabort+0x14/0x20
[ 35.968346 ] peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.968752 ] pci_device_remove+0xa9/0x250
Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards")
Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
notification
commit 3d031abc7e7249573148871180c28ecedb5e27df upstream.
This corrects the lack of notification of a return to ERROR_ACTIVE
state for USB - CANFD devices from PEAK-System.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Link: https://lore.kernel.org/all/20210929142111.55757-1-s.grosjean@peak-system.com
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7c05c3987dcfde9a4e8c2d533db013fabebca0d upstream.
If the driver was not opened, rcar_can_suspend() should not call
clk_disable() because the clock was not enabled.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com
Cc: stable@vger.kernel.org
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
and TX error counters
commit 044012b52029204900af9e4230263418427f4ba4 upstream.
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f6b3c7848e66e9046c8a79a5b88fd03461cc252b ]
The hi3110_cmd() is supposed to return zero on success and negative
error codes on failure, but it was accidentally declared as a u8 when
it needs to be an int type.
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
Link: https://lore.kernel.org/r/20210729141246.GA1267@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 928150fad41ba16df7fcc9f7f945747d0f56cbb6 upstream.
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/b31b096926dcb35998ad0271aac4b51770ca7cc8.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9969e3c5f40c166e3396acc36c34f9de502929f6 upstream.
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/59aa9fbc9a8cbf9af2bbd2f61a659c480b415800.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0e865f0c31928d6a313269ef624907eec55287c4 upstream.
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/r/d39b458cd425a1cf7f512f340224e6e9563b07bd.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc43fb69a7af92839551f99c1a96a37b77b3ae7a upstream.
Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c02557174b ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.
In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().
All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.
| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
Fixes: 91c02557174b ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TX path
commit b17233d385d0b6b43ecf81d43008cb1bbb008166 upstream.
Rather than just indicating that transmission can start, this patch
requires the explicit flushing of the network TX queue when the driver
is informed by the device that it can transmit, next to its
configuration.
In this way, if frames have already been written by the application,
they will actually be transmitted.
Fixes: ffd137f7043c ("can: peak/pcie_fd: remove useless code when interface starts")
Link: https://lore.kernel.org/r/20210623142600.149904-1-s.grosjean@peak-system.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab4a0b8fcb9a95c02909b62049811bd2e586aaa4 upstream.
In ems_usb_disconnect() dev pointer, which is netdev private data, is
used after free_candev() call:
| if (dev) {
| unregister_netdev(dev->netdev);
| free_candev(dev->netdev);
|
| unlink_all_urbs(dev);
|
| usb_free_urb(dev->intr_urb);
|
| kfree(dev->intr_in_buffer);
| kfree(dev->tx_msg_buffer);
| }
Fix it by simply moving free_candev() at the end of the block.
Fail log:
| BUG: KASAN: use-after-free in ems_usb_disconnect
| Read of size 8 at addr ffff88804e041008 by task kworker/1:2/2895
|
| CPU: 1 PID: 2895 Comm: kworker/1:2 Not tainted 5.13.0-rc5+ #164
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.4
| Workqueue: usb_hub_wq hub_event
| Call Trace:
| dump_stack (lib/dump_stack.c:122)
| print_address_description.constprop.0.cold (mm/kasan/report.c:234)
| kasan_report.cold (mm/kasan/report.c:420 mm/kasan/report.c:436)
| ems_usb_disconnect (drivers/net/can/usb/ems_usb.c:683 drivers/net/can/usb/ems_usb.c:1058)
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/20210617185130.5834-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91c02557174be7f72e46ed7311e3bea1939840b0 upstream.
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0b96b4a62745397aee662670cfc2157bac03f55 upstream.
syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.
backtrace:
[<0000000079d6542a>] kmalloc include/linux/slab.h:552 [inline]
[<0000000079d6542a>] kzalloc include/linux/slab.h:682 [inline]
[<0000000079d6542a>] pcan_usb_fd_init+0x156/0x210 drivers/net/can/usb/peak_usb/pcan_usb_fd.c:868 [2]
[<00000000c09f9057>] peak_usb_create_dev drivers/net/can/usb/peak_usb/pcan_usb_core.c:851 [inline] [1]
[<00000000c09f9057>] peak_usb_probe+0x389/0x490 drivers/net/can/usb/peak_usb/pcan_usb_core.c:949
Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47c5e474bc1e1061fb037d13b5000b38967eb070 upstream.
For cases when flexcan is built-in, bitrate is still not set at
registering. So flexcan_chip_freeze() generates:
[ 1.860000] *** ZERO DIVIDE *** FORMAT=4
[ 1.860000] Current process id is 1
[ 1.860000] BAD KERNEL TRAP: 00000000
[ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8
To allow chip freeze, using an hardcoded timeout when bitrate is still
not set.
Fixes: ec15e27cc890 ("can: flexcan: enable RX FIFO after FRZ/HALT valid")
Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.org
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
[mkl: use if instead of ? operator]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Koen Vandeputte <koen.vandeputte@citymesh.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d7047ed6b7214fbabc16d8712a822e256b1aa44 upstream.
In commit 6417f03132a6 ("module: remove never implemented
MODULE_SUPPORTED_DEVICE") the MODULE_SUPPORTED_DEVICE macro was
removed from the kerne entirely. Shortly before this patch was applied
mainline the commit 59ec7b89ed3e ("can: peak_usb: add forgotten
supported devices") was added to net/master. As this would result in a
merge conflict, let's revert this patch.
Fixes: 59ec7b89ed3e ("can: peak_usb: add forgotten supported devices")
Link: https://lore.kernel.org/r/20210320192649.341832-1-mkl@pengutronix.de
Suggested-by: Leon Romanovsky <leon@kernel.org>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a5ca857079ea022e0b1b17fc154f7ad7dbc150f upstream.
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8dc7 ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c0e399f3baf42279f48991554240af8c457535d1 ]
Message loss from RX FIFO 0 is already handled in
m_can_handle_lost_msg(), with netdev output included.
Removing this warning also improves driver performance under heavy
load, where m_can_do_rx_poll() may be called many times before this
interrupt is cleared, causing this message to be output many
times (thanks Mariusz Madej for this report).
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/r/20210303103151.3760532-1-torin@maxiluxsystems.com
Reported-by: Mariusz Madej <mariusz.madej@xtrack.com>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e2fe01dd6f98da6cae8b07cd5cfa67abc70d97d ]
Currently doing modprobe c_can_pci will make the kernel complain:
Unbalanced pm_runtime_enable!
this is caused by pm_runtime_enable() called before pm is initialized.
This fix is similar to 227619c3ff7c, move those pm_enable/disable code
to c_can_platform.
Fixes: 4cdd34b26826 ("can: c_can: Add runtime PM support to Bosch C_CAN/D_CAN controller")
Link: http://lore.kernel.org/r/20210302025542.987600-1-ztong0001@gmail.com
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0429d6d89f97ebff4f17f13f5b5069c66bde8138 ]
There is a UAF in c_can_pci_remove(). dev is released by
free_c_can_dev() and is used by pci_iounmap(pdev, priv->base) later.
To fix this issue, save the mmio address before releasing dev.
Fixes: 5b92da0443c2 ("c_can_pci: generic module for C_CAN/D_CAN on PCI")
Link: https://lore.kernel.org/r/20210301024512.539039-1-ztong0001@gmail.com
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59ec7b89ed3e921cd0625a8c83f31a30d485fdf8 ]
Since the peak_usb driver also supports the CAN-USB interfaces
"PCAN-USB X6" and "PCAN-Chip USB" from PEAK-System GmbH, this patch adds
their names to the list of explicitly supported devices.
Fixes: ea8b65b596d7 ("can: usb: Add support of PCAN-Chip USB stamp module")
Fixes: f00b534ded60 ("can: peak: Add support for PCAN-USB X6 USB interface")
Link: https://lore.kernel.org/r/20210309082128.23125-3-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ec15e27cc8904605846a354bb1f808ea1432f853 upstream.
RX FIFO enable failed could happen when do system reboot stress test:
[ 0.303958] flexcan 5a8d0000.can: 5a8d0000.can supply xceiver not found, using dummy regulator
[ 0.304281] flexcan 5a8d0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.314640] flexcan 5a8d0000.can: registering netdev failed
[ 0.320728] flexcan 5a8e0000.can: 5a8e0000.can supply xceiver not found, using dummy regulator
[ 0.320991] flexcan 5a8e0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.331360] flexcan 5a8e0000.can: registering netdev failed
[ 0.337444] flexcan 5a8f0000.can: 5a8f0000.can supply xceiver not found, using dummy regulator
[ 0.337716] flexcan 5a8f0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.348117] flexcan 5a8f0000.can: registering netdev failed
RX FIFO should be enabled after the FRZ/HALT are valid. But the current
code enable RX FIFO and FRZ/HALT at the same time.
Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20210218110037.16591-3-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 449052cfebf624b670faa040245d3feed770d22f upstream.
Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is
asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although
the reset value is 1b'1. This is a prepare patch, later patch will
invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze
mode acknowledge.
Fixes: b1aa1c7a2165b ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze")
Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b552766c872f5b0d90323b24e4c9e8fa67486dd5 ]
The "bec" struct isn't necessarily always initialized. For example, the
mcp251xfd_get_berr_counter() function doesn't initialize anything if the
interface is down.
Fixes: 52c793f24054 ("can: netlink support for bus-error reporting and counters")
Link: https://lore.kernel.org/r/YAkaRdRJncsJO8Ve@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75854cad5d80976f6ea0f0431f8cedd3bcc475cb ]
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the canfd_frame cfd which aliases skb memory is accessed
after the netif_rx_ni().
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)")
Link: https://lore.kernel.org/r/20210120114137.200019-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03f16c5075b22c8902d2af739969e878b0879c94 ]
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the netif_rx_ni() in:
stats->rx_bytes += cf->len;
Reordering the lines solves the issue.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/r/20210120114137.200019-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d1be581ec6b92a338bb7ed23e1381f45ddf336f ]
If softing_netdev_open() fails, we should call close_candev() to avoid
reference leak.
Fixes: 03fd3cf5a179d ("can: add driver for Softing card")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Link: https://lore.kernel.org/r/20201202151632.1343786-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201204133508.742120-2-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3409e4192535fbcc86a84b7a65d9351f46039ec ]
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0e1 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ba1cb39fce4464151517a37ce0ac0a1a3f580d6 ]
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd0d83eab2e0c26fe87a10debfedbb23901853c1 ]
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a68cc0d690c9e5730d676b764c6f059343b842c ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
can_put_echo_skb()
[ Upstream commit 81c9c8e0adef3285336b942f93287c554c89e6c6 ]
The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7968c7c79d3be8987feb8021f0c46e6866831408 ]
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1e654070a60d5d4f7cce59c38f4ca790bb79121 ]
netif_rx() is meant to be called from interrupt contexts. can_restart() may be
called by can_restart_work(), which is called from a worqueue, so it may run in
process context. Use netif_rx_ni() instead.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu>
Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu
[mkl: use netif_rx_ni() instead of netif_rx_any_context()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93ef65e5a6357cc7381f85fcec9283fe29970045 ]
Echo management is driven by PUCAN_MSG_LOOPED_BACK bit, while loopback
frames are identified with PUCAN_MSG_SELF_RECEIVE bit. Those bits are set
for each outgoing frame written to the IP core so that a copy of each one
will be placed into the rx path. Thus,
- when PUCAN_MSG_LOOPED_BACK is set then the rx frame is an echo of a
previously sent frame,
- when PUCAN_MSG_LOOPED_BACK+PUCAN_MSG_SELF_RECEIVE are set, then the rx
frame is an echo AND a loopback frame. Therefore, this frame must be
put into the socket rx path too.
This patch fixes how CAN frames are handled when these are sent while the
can interface is configured in "loopback on" mode.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20201013153947.28012-1-s.grosjean@peak-system.com
Fixes: 8ac8321e4a79 ("can: peak: add support for PEAK PCAN-PCIe FD CAN-FD boards")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecc7b4187dd388549544195fb13a11b4ea8e6a84 ]
Fabian Inostroza <fabianinostrozap@gmail.com> has discovered a potential
problem in the hardware timestamp reporting from the PCAN-USB USB CAN interface
(only), related to the fact that a timestamp of an event may precede the
timestamp used for synchronization when both records are part of the same USB
packet. However, this case was used to detect the wrapping of the time counter.
This patch details and fixes the two identified cases where this problem can
occur.
Reported-by: Fabian Inostroza <fabianinostrozap@gmail.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20201014085631.15128-1-s.grosjean@peak-system.com
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a6921dd524fe31d1f460c161d3526a407533b6db ]
These values come from skb->data so Smatch considers them untrusted. I
believe Smatch is correct but I don't have a way to test this.
The usb_if->dev[] array has 2 elements but the index is in the 0-15
range without checks. The cfd->len can be up to 255 but the maximum
valid size is CANFD_MAX_DLEN (64) so that could lead to memory
corruption.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200813140604.GA456946@mwanda
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
frames
[ Upstream commit ed3320cec279407a86bc4c72edc4a39eb49165ec ]
The can_get_echo_skb() function returns the number of received bytes to
be used for netdev statistics. In the case of RTR frames we get a valid
(potential non-zero) data length value which has to be passed for further
operations. But on the wire RTR frames have no payload length. Therefore
the value to be used in the statistics has to be zero for RTR frames.
Reported-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201020064443.80164-1-socketcan@hartkopp.net
Fixes: cf5046b309b3 ("can: dev: let can_get_echo_skb() return dlc of CAN frame")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2283f79b22684d2812e5c76fc2280aae00390365 ]
If a driver calls can_get_echo_skb() during a hardware IRQ (which is often, but
not always, the case), the 'WARN_ON(in_irq)' in
net/core/skbuff.c#skb_release_head_state() might be triggered, under network
congestion circumstances, together with the potential risk of a NULL pointer
dereference.
The root cause of this issue is the call to kfree_skb() instead of
dev_kfree_skb_irq() in net/core/dev.c#enqueue_to_backlog().
This patch prevents the skb to be freed within the call to netif_rx() by
incrementing its reference count with skb_get(). The skb is finally freed by
one of the in-irq-context safe functions: dev_consume_skb_any() or
dev_kfree_skb_any(). The "any" version is used because some drivers might call
can_get_echo_skb() in a normal context.
The reason for this issue to occur is that initially, in the core network
stack, loopback skb were not supposed to be received in hardware IRQ context.
The CAN stack is an exeption.
This bug was previously reported back in 2017 in [1] but the proposed patch
never got accepted.
While [1] directly modifies net/core/dev.c, we try to propose here a
smoother modification local to CAN network stack (the assumption
behind is that only CAN devices are affected by this issue).
[1] http://lore.kernel.org/r/57a3ffb6-3309-3ad5-5a34-e93c3fe3614d@cetitec.com
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20201002154219.4887-2-mailhol.vincent@wanadoo.fr
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2ddd6bfe7bdbb6c661835c3ff9cab8e0769940a6 ]
A CAN driver, using the rx-offload infrastructure, is reading CAN frames
(usually in IRQ context) from the hardware and placing it into the rx-offload
queue to be delivered to the networking stack via NAPI.
In case the rx-offload queue is full, trying to add more skbs results in the
skbs being dropped using kfree_skb(). If done from hard-IRQ context this
results in the following warning:
[ 682.552693] ------------[ cut here ]------------
[ 682.557360] WARNING: CPU: 0 PID: 3057 at net/core/skbuff.c:650 skb_release_head_state+0x74/0x84
[ 682.566075] Modules linked in: can_raw can coda_vpu flexcan dw_hdmi_ahb_audio v4l2_jpeg imx_vdoa can_dev
[ 682.575597] CPU: 0 PID: 3057 Comm: cansend Tainted: G W 5.7.0+ #18
[ 682.583098] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 682.589657] [<c0112628>] (unwind_backtrace) from [<c010c1c4>] (show_stack+0x10/0x14)
[ 682.597423] [<c010c1c4>] (show_stack) from [<c06c481c>] (dump_stack+0xe0/0x114)
[ 682.604759] [<c06c481c>] (dump_stack) from [<c0128f10>] (__warn+0xc0/0x10c)
[ 682.611742] [<c0128f10>] (__warn) from [<c0129314>] (warn_slowpath_fmt+0x5c/0xc0)
[ 682.619248] [<c0129314>] (warn_slowpath_fmt) from [<c0b95dec>] (skb_release_head_state+0x74/0x84)
[ 682.628143] [<c0b95dec>] (skb_release_head_state) from [<c0b95e08>] (skb_release_all+0xc/0x24)
[ 682.636774] [<c0b95e08>] (skb_release_all) from [<c0b95eac>] (kfree_skb+0x74/0x1c8)
[ 682.644479] [<c0b95eac>] (kfree_skb) from [<bf001d1c>] (can_rx_offload_queue_sorted+0xe0/0xe8 [can_dev])
[ 682.654051] [<bf001d1c>] (can_rx_offload_queue_sorted [can_dev]) from [<bf001d6c>] (can_rx_offload_get_echo_skb+0x48/0x94 [can_dev])
[ 682.666007] [<bf001d6c>] (can_rx_offload_get_echo_skb [can_dev]) from [<bf01efe4>] (flexcan_irq+0x194/0x5dc [flexcan])
[ 682.676734] [<bf01efe4>] (flexcan_irq [flexcan]) from [<c019c1ec>] (__handle_irq_event_percpu+0x4c/0x3ec)
[ 682.686322] [<c019c1ec>] (__handle_irq_event_percpu) from [<c019c5b8>] (handle_irq_event_percpu+0x2c/0x88)
[ 682.695993] [<c019c5b8>] (handle_irq_event_percpu) from [<c019c64c>] (handle_irq_event+0x38/0x5c)
[ 682.704887] [<c019c64c>] (handle_irq_event) from [<c01a1058>] (handle_fasteoi_irq+0xc8/0x180)
[ 682.713432] [<c01a1058>] (handle_fasteoi_irq) from [<c019b2c0>] (generic_handle_irq+0x30/0x44)
[ 682.722063] [<c019b2c0>] (generic_handle_irq) from [<c019b8f8>] (__handle_domain_irq+0x64/0xdc)
[ 682.730783] [<c019b8f8>] (__handle_domain_irq) from [<c06df4a4>] (gic_handle_irq+0x48/0x9c)
[ 682.739158] [<c06df4a4>] (gic_handle_irq) from [<c0100b30>] (__irq_svc+0x70/0x98)
[ 682.746656] Exception stack(0xe80e9dd8 to 0xe80e9e20)
[ 682.751725] 9dc0: 00000001 e80e8000
[ 682.759922] 9de0: e820cf80 00000000 ffffe000 00000000 eaf08fe4 00000000 600d0013 00000000
[ 682.768117] 9e00: c1732e3c c16093a8 e820d4c0 e80e9e28 c018a57c c018b870 600d0013 ffffffff
[ 682.776315] [<c0100b30>] (__irq_svc) from [<c018b870>] (lock_acquire+0x108/0x4e8)
[ 682.783821] [<c018b870>] (lock_acquire) from [<c0e938e4>] (down_write+0x48/0xa8)
[ 682.791242] [<c0e938e4>] (down_write) from [<c02818dc>] (unlink_file_vma+0x24/0x40)
[ 682.798922] [<c02818dc>] (unlink_file_vma) from [<c027a258>] (free_pgtables+0x34/0xb8)
[ 682.806858] [<c027a258>] (free_pgtables) from [<c02835a4>] (exit_mmap+0xe4/0x170)
[ 682.814361] [<c02835a4>] (exit_mmap) from [<c01248e0>] (mmput+0x5c/0x110)
[ 682.821171] [<c01248e0>] (mmput) from [<c012e910>] (do_exit+0x374/0xbe4)
[ 682.827892] [<c012e910>] (do_exit) from [<c0130888>] (do_group_exit+0x38/0xb4)
[ 682.835132] [<c0130888>] (do_group_exit) from [<c0130914>] (__wake_up_parent+0x0/0x14)
[ 682.843063] irq event stamp: 1936
[ 682.846399] hardirqs last enabled at (1935): [<c02938b0>] rmqueue+0xf4/0xc64
[ 682.853553] hardirqs last disabled at (1936): [<c0100b20>] __irq_svc+0x60/0x98
[ 682.860799] softirqs last enabled at (1878): [<bf04cdcc>] raw_release+0x108/0x1f0 [can_raw]
[ 682.869256] softirqs last disabled at (1876): [<c0b8f478>] release_sock+0x18/0x98
[ 682.876753] ---[ end trace 7bca4751ce44c444 ]---
This patch fixes the problem by replacing the kfree_skb() by
dev_kfree_skb_any(), as rx-offload might be called from threaded IRQ handlers
as well.
Fixes: ca913f1ac024 ("can: rx-offload: can_rx_offload_queue_sorted(): fix error handling, avoid skb mem leak")
Fixes: 6caf8a6d6586 ("can: rx-offload: can_rx_offload_queue_tail(): fix error handling, avoid skb mem leak")
Link: http://lore.kernel.org/r/20201019190524.1285319-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9ad02c7f4f279504bdd38ab706fdc97d5f2b2a9c ]
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit da2311a6385c3b499da2ed5d9be59ce331fa93e9 upstream.
Uninitialized Kernel memory can leak to USB devices.
Fix this by using kzalloc() instead of kmalloc().
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Fixes: 7259124eac7d ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.19
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[bwh: Backported to 4.9: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b9258a2cece4ec1f020715fe3554bc2e360f6264 ]
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Fixes: a1044e36e457 ("can: add slcan driver for serial/USB-serial CAN adapters")
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: security@kernel.org
Cc: wg@grandegger.com
Cc: mkl@pengutronix.de
Cc: davem@davemloft.net
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2091a3d42b4f339eaeed11228e0cbe9d4f92f558 ]
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
This patch is a 1:1 copy of upstream slip.c commit f596c87005f7
("slip: not call free_netdev before rtnl_unlock in slip_open").
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ab02ad660586b94f5d08912a3952b939cf4c4430 ]
Add missing attribute validation for IFLA_CAN_TERMINATION
to the netlink policy.
Fixes: 12a6075cabc0 ("can: dev: add CAN interface termination API")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0ace17d56824165c7f4c68785d6b58971db954dd ]
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21b1 ("slip: Fix deadlock in write_wakeup")
Fixes: a8e83b17536a ("slcan: Port write_wakeup deadlock fix from slip")
Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tyler Hall <tylerwhall@gmail.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
to irq mode
commit 2d77bd61a2927be8f4e00d9478fe6996c47e8d45 upstream.
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f361cd9474ab2c4ab9ac8db20faf81e66c6279b upstream.
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ebd796e24008f33f06ebea5a5e6aceb68b51794 upstream.
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:634
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
sl_sync drivers/net/slip/slip.c:725 [inline]
slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801
tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469
tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596
tiocsetd drivers/tty/tty_io.c:2334 [inline]
tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: ed50e1600b44 ("slcan: Fix memory leak in error path")
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Miller <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1f7f504dcd9d1262437bdcf4fa071e41dec1af03 ]
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2a9f74c9d18acfdcabd3361adc7eac82c537a66 ]
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|