| Age | Commit message (Collapse) | Author |
|---|
|
The NAND controller returns ECC failure during read of completely
erased codeword. The NAND controller has hardware functionality
to detect erased codeword in case of BCH ECC algorithm. The
NAND_ERASED_CW_DETECT_CFG register controls the erased
codeword/page detection controller. This register should be reset
before every page read by setting and clearing bit 0 of
NAND_ERASED_CW_DETECT_CFG.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
In EBI2, all codeword data will be read in FLASH_BUF_ACC buffer
and ADM will copy the data from source (FLASH_BUF_ACC) to
destination (memory for data read).
In QPIC, there is no FLASH_BUF_ACC and all the codeword data will
held in QPIC BAM FIFO buffers. It provides multiple READ_LOCATION
registers which will be used for copying the data from FIFO to
memory. The READ_LOCATION register will be used to read a
specific amount of data from a specific offset within the flash
buffer. It supports sequential offset requests. Each request is
composed of the following fields:
a. Offset within the flash buffer from which data should be
read
b. Amount of data to be read
c. Flag bit specifying the last read request from the flash
buffer. Following the last read request the NANDc refers to the
buffer as empty.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The QPIC NAND BAM has multiple flags to control the transfer. This
patch adds flags parameter in register and data transfer DMA helper
functions and modifies all these functions call with appropriate
flags using following rule
1. Read and write can’t go in single command descriptor so
separate SGL should be used.
2. For some of the requests, NWD flag should be set in BAM
DMA descriptor.
3. For Data write, the BAM has internal buffer for each codeword.
All write request will modify the data in internal buffer and
this buffer will be flushed to NAND device once EOT flag is set.
So for all the write requests in single codeword, the EOT should
be cleared for all tx data descriptors except the last one.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
1. prepare_bam_async_desc is the function which will call
all the DMA API’s. It will fetch the outstanding scatter gather
list for passed channel and will do the DMA descriptor formation.
The DMA flag is dependent upon the type of channel.
2. For ADM DMA, the descriptor is being formed for every DMA
request so its sgl count will be always 1 while in BAM DMA, the
clubbing of descriptor is being done to increase throughput.
3. ADM DMA uses only one channel while in BAM DMA, data descriptors
will be submitted to tx channel (for write) or rx channel
(for read) and all the registers read/write descriptors in
command channel.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
- The BAM transaction is the core data structure which will be used
for all the data transfers in QPIC NAND. Since the core framework
in nand_base.c is serializing all the NAND requests so allocating
BAM transaction before every transfer will be overhead. The memory
for it be allocated during probe time and before every transfer,
it will be cleared.
- The BAM transaction contains the array of
command and data scatter gather list and indexes. For
every transfer, all the resource will be taken from BAM
transaction.
- The size of the buffer used for BAM transactions
is calculated based on the NAND device with the maximum page size,
among all the devices connected to the
controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The EBI2 NAND controller directly remaps register read buffer with
dma_map_sg and DMA address of this buffer will be passed to DMA
API’s. While, on QPIC NAND controller, which uses BAM DMA, we read
the controller registers by preparing a BAM command descriptor. This
command descriptor requires the
- controller register address
- the DMA address in which we want to store the value read
back from the controller register.
This command descriptor will be remapped with dma_map_sg
and its DMA address will be passed to DMA API’s. Therefore,
it's required that we also map our register read buffer for
DMA (using dma_map_single). We use the returned DMA address
for preparing entries in our command descriptor.
This patch adds the DMA mapping support for register read
buffer. This buffer will be DMA mapped during allocation
time. Before starting of any operation, this buffer will
be synced for device operation and after operation
completion, it will be synced again for CPU.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
1. QPIC NAND controller uses 3 BAM channels: command, data tx
and data rx while EBI2 NAND controller uses only single ADM
channel.
2. CRCI is only required for ADM DMA and it's not required for
BAM DMA.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The current driver only supports EBI2 NAND controller which uses
ADM DMA. The latest QCOM SoC uses QPIC NAND controller with BAM
DMA. NAND registers and programming sequence are same for EBI2
and QPIC NAND so the same driver can support QPIC NAND also by
adding the BAM DMA support. This patch adds the is_bam in NAND
property which will be checked for determining the DMA engine type.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Currently driver data is being assigned directly with ECC modes.
Now, the plan is to add more NAND controller versions which will
have different properties. This patch reorganizes the current driver
data assignment by creating NAND controller properties structure
which will contain all properties specific to NAND controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would
then call devm_request_irq() for IRQ0 in its probe method and never get
a valid interrupt.
Check for 'nc->irq <= 0' instead and return -ENXIO from the driver's probe
if of_irq_get() returned 0.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Wenyou Yang <Wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)
Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: 78f3482d7480 ("mtd: nand: hynix: Rework NAND ID decoding to extract more information")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
- clk_prepare_enable() can fail here and we must check its return value.
- oxnas_nand_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
orion_nand_read_buf uses an inline assembly with the "ldrd"
instruction, which is only available from ARMv5 upwards. This
used to be fine, since all users have an ARMv5 or ARMv7 CPU,
but now we can also build a multiplatform kernel with ARMv4
support enabled in addition to the "kirkwood" (mvebu) platform.
This provides an alternative to call the readsl() function that
is supposed to have the same effect and is also optimized for
performance.
I first posted a version of this patch back in 2014, and there
was some discussion about it then. This fixes the bugs identified
back then and should be a reasonable alternative for the rare
corner case.
Link: https://patchwork.kernel.org/patch/4144791/
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The controller supported by the pxa3xx_nand driver is also available on
the mvebu 64-bit SoCs, such as the Armada 7K and Armada 8K SoCs. This
patch updates the Kconfig dependency to allow building the kernel for
this SoC family too.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The NAND controller can support multiple NAND devices having different
page sizes. Future code will require us to allocate memory based on the
maximum number of codewords among all the devices. We reorganize the
NAND device probing such that the ONFI parameters are first read for
each connected device to identify the maximum number of codewords
possible, and only then proceed with MTD device registration (i.e, call
nand_scan_tail and mtd_device_register).
This is a reorganization of the existing code and will not change any
functionality.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The memset in clear_read_regs is overhead. All the register data
will be filled by DMA during NAND operation so making these
register variables zero is not required.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Each NAND page consist of multiple codewords. Following is
sequence for NAND page write according to hardware guide.
1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.
The step 1 should be done once for each page and step 2,3 should
be done for each codeword.
Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes page write functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Each NAND page consist of multiple codewords. Following is
sequence for NAND page read according to hardware guide.
1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.
The step 1 should be done once for each page and step 2,3 should
be done for each codeword.
Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes read page functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.
Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which
0x1 : BCH_DISABLED
0x0 : BCH_ENABLED
But currently host->bch_enabled is being assigned to BCH_DISABLED.
Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
pinctrl_pm_select_default_state() is already the default pinctrl state and
since pinctrl_pm_select_sleep_state() is not used in this driver, there
is no need to explicitly call pinctrl_pm_select_default_state().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.
NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22bfe1f for defining ids length in nand_flash_ids[] list.
This commit unifies ids length in nand base driver.
Signed-off-by: Jean-Louis Thekekara <jeanlouis.thekekara@parrot.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The nand_scan_ident() function is not expected to allocate resources,
and people are usually not calling nand_cleanup() if something fails
between nand_scan_ident() and nand_scan_tail().
Move all functions that may allocate resource to the nand_scan_tail()
path to prevent such resource leaks.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
|
|
Commit 7d70f334ad2b ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.
Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
EDO mode should be used when tRC is less than 30ns, but timings are
expressed in picoseconds in the nand_sdr_timings struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f9ce2eddf176 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Reported-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 204e7ecd47e2 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some ONFI NANDs do not support the SET/GET FEATURES commands, which,
according to the spec, is perfectly valid.
On these NANDs we can't set a specific timing mode using the "timing
mode" feature, and we should assume the NAND does not require any setup
to enter a specific timing mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 0b4773fd1649 (mtd: nand: Drop unused cached programming support)
removed the "cached" parameter from nand_write_page(), but did not update
the kerneldoc comments, creating this docs build warning:
./drivers/mtd/nand/nand_base.c:2751: warning: Excess function parameter 'cached' description in 'nand_write_page'
Remove the offending line so we can have a little peace and quiet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_round_rate() can return <= 0. Currently the value returned by
clk_round_rate() is used directly for a division. This patch introduces a
guard to ensure a divide-by-zero or a divide by a negative number for that
matter can't happen by bugging out returning -EINVAL if clk_round_rate()
returns <= 0.
Fixes: 2d43457f79e4 ("mtd: nand: sunxi: fix EDO mode selection")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When using soft ecc, if no ooblayout is given, the core automatically
uses one of the nand_ooblayout_{sp,lp}*() functions to determine the
layout inside the out of band data.
Until kernel version 4.6, struct nand_ecclayout was used for that
purpose. During the migration from 4.6 to 4.7, an error shown up in the
small page layout, in the case oob section is only 8 bytes long.
The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4)
as free bytes, one byte (5) for bad block marker and finally
two bytes (6, 7) as free bytes, as shown there:
[linux-4.6] drivers/mtd/nand/nand_base.c:52
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.eccpos = {0, 1, 2},
.oobfree = {
{.offset = 3,
.length = 2},
{.offset = 6,
.length = 2} }
};
This fixes the current implementation which is incoherent. It
references bit 3 at the same time as an ecc byte and a free byte.
Furthermore, it is clear with the previous implementation that there
is only one ecc section with 8 bytes oob sections. We shall return
-ERANGE in the nand_ooblayout_ecc_sp() function when asked for the
second section.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Several MTD devices are using debugfs entries created in the root.
This commit provides the means for a standardized subtree, creating
one "mtd" entry at root, and one entry per device inside it, named
after the device.
The tree is registered in add_mtd_device, and released in
del_mtd_device.
Devices docg3, mtdswap and nandsim were updated to use this subtree
instead of custom ones, and their entries were prefixed with the
drivers' names.
Signed-off-by: Mario J. Rugiero <mrugiero@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
PMECC caps extraction from old DT bindings is broken, thus leading to
erroneous EL registers offset, which in turn make HW ECC unusable on
sama5d2 when old bindings are in use.
Passing the NAND dev node instead of the NFC node to of_match_node()
solves the problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Tested-by: Romain Izard <romain.izard.pro@gmail.com>
|
|
Pull MTD updates from Brian Norris:
"General updates:
- Cleanups and additional flash support for "dataflash" driver
- new driver for mchp23k256 SPI SRAM device
- improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
- refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPINOR updates, from Cyrille Pitchen and Marek Vasut:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
- addition of on-die ECC support to Micron driver
- addition of helpers to help drivers choose most appropriate ECC
settings
- deletion of dead-code (cached programming and ->errstat() hook)
- make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
- change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
- support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
- change the prototype of ->setup_data_interface()
A bunch of driver related changes:
- various cleanup, fixes and improvements of the MTK driver
- OMAP DT bindings fixes
- support for ->setup_data_interface() in the fsmc driver
- support for imx7 in the gpmi driver
- finalization of the denali driver rework (thanks to Masahiro for
the work he's done on this driver)
- fix "bitflips in erased pages" handling in the ifc driver
- addition of PM ops and dynamic timing configuration to the atmel
driver"
* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
Documentation: ABI: mtd: describe "offset" more precisely
mtd: Fix check in mtd_unpoint()
mtd: nand: mtk: release lock on error path
mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
mtd: spi-nor: cqspi: remove duplicate const
mtd: spi-nor: Add support for Spansion S25FL064L
mtd: spi-nor: Add support for mx66u51235f
mtd: nand: mtk: add ->setup_data_interface() hook
mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
mtd: nand: mtk: disable ecc irq when writing page with hwecc
mtd: nand: mtk: fix incorrect register setting order about ecc irq
mtd: partitions: fixup some allocate_partition() whitespace
mtd: parsers: trx: fix pr_err format for printing offset
MAINTAINERS: Update SPI NOR subsystem git repositories
mtd: extract TRX parser out of bcm47xxpart into a separated module
mtd: partitions: add support for partition parsers
mtd: partitions: add support for subpartitions
mtd: partitions: rename "master" to the "parent" where appropriate
mtd: partitions: remove sysfs files when deleting all master's partitions
...
|
|
From Boris:
"""
This pull request contains the following core changes:
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
|
|
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
|
|
We only want to hold the lock on the success path, not this error path.
Fixes: 7ec4a37c5d71 ("mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Linux 4.12-rc7
|
|
Currently, we use the fixed ACC timing 0x10804211. This is not the best
setting for each case. Actually, MTK NAND controller can adapt ACC timings
dynamically according to nfi clock frequence.
Implement the ->setup_data_interface() hook to optimize driver performance.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
Abhishek Sahu
Gustavo A. R. Silva
Pan Bian
Sergei Shtylyov
Martin Blumenstingl
Boris Brezillon
Philipp Zabel
Arvind Yadav
Arnd Bergmann
Gregory CLEMENT
Fabio Estevam
Jean-Louis Thekekara
Jonathan Corbet
Bryan O'Donoghue
Miquel Raynal
Mario Rugiero
Linus Torvalds
Brian Norris
Dan Carpenter
Linus Walleij
Xiaolei Li